From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- arch/arm/plat-samsung/include/plat/adc-core.h | 28 ++ arch/arm/plat-samsung/include/plat/adc.h | 36 +++ arch/arm/plat-samsung/include/plat/ata-core.h | 28 ++ arch/arm/plat-samsung/include/plat/backlight.h | 26 ++ arch/arm/plat-samsung/include/plat/cpu-freq-core.h | 291 +++++++++++++++++++++ arch/arm/plat-samsung/include/plat/cpu-freq.h | 145 ++++++++++ arch/arm/plat-samsung/include/plat/cpu.h | 143 ++++++++++ arch/arm/plat-samsung/include/plat/devs.h | 100 +++++++ arch/arm/plat-samsung/include/plat/fb-core.h | 29 ++ arch/arm/plat-samsung/include/plat/fb-s3c2410.h | 72 +++++ arch/arm/plat-samsung/include/plat/fb.h | 35 +++ .../plat-samsung/include/plat/gpio-cfg-helpers.h | 163 ++++++++++++ arch/arm/plat-samsung/include/plat/gpio-cfg.h | 182 +++++++++++++ arch/arm/plat-samsung/include/plat/gpio-core.h | 145 ++++++++++ arch/arm/plat-samsung/include/plat/iic-core.h | 42 +++ arch/arm/plat-samsung/include/plat/irq-uart.h | 20 ++ arch/arm/plat-samsung/include/plat/keypad-core.h | 31 +++ arch/arm/plat-samsung/include/plat/keypad.h | 31 +++ arch/arm/plat-samsung/include/plat/map-base.h | 46 ++++ arch/arm/plat-samsung/include/plat/map-s3c.h | 84 ++++++ arch/arm/plat-samsung/include/plat/map-s5p.h | 40 +++ arch/arm/plat-samsung/include/plat/nand-core.h | 28 ++ arch/arm/plat-samsung/include/plat/onenand-core.h | 37 +++ arch/arm/plat-samsung/include/plat/pm-common.h | 110 ++++++++ arch/arm/plat-samsung/include/plat/pm.h | 121 +++++++++ arch/arm/plat-samsung/include/plat/pwm-core.h | 22 ++ arch/arm/plat-samsung/include/plat/regs-adc.h | 68 +++++ arch/arm/plat-samsung/include/plat/regs-irqtype.h | 21 ++ arch/arm/plat-samsung/include/plat/regs-spi.h | 48 ++++ arch/arm/plat-samsung/include/plat/regs-srom.h | 54 ++++ arch/arm/plat-samsung/include/plat/regs-udc.h | 151 +++++++++++ .../plat-samsung/include/plat/regs-usb-hsotg-phy.h | 51 ++++ arch/arm/plat-samsung/include/plat/samsung-time.h | 30 +++ arch/arm/plat-samsung/include/plat/sdhci.h | 166 ++++++++++++ arch/arm/plat-samsung/include/plat/spi-core.h | 30 +++ arch/arm/plat-samsung/include/plat/usb-phy.h | 19 ++ arch/arm/plat-samsung/include/plat/wakeup-mask.h | 44 ++++ .../arm/plat-samsung/include/plat/watchdog-reset.h | 20 ++ 38 files changed, 2737 insertions(+) create mode 100644 arch/arm/plat-samsung/include/plat/adc-core.h create mode 100644 arch/arm/plat-samsung/include/plat/adc.h create mode 100644 arch/arm/plat-samsung/include/plat/ata-core.h create mode 100644 arch/arm/plat-samsung/include/plat/backlight.h create mode 100644 arch/arm/plat-samsung/include/plat/cpu-freq-core.h create mode 100644 arch/arm/plat-samsung/include/plat/cpu-freq.h create mode 100644 arch/arm/plat-samsung/include/plat/cpu.h create mode 100644 arch/arm/plat-samsung/include/plat/devs.h create mode 100644 arch/arm/plat-samsung/include/plat/fb-core.h create mode 100644 arch/arm/plat-samsung/include/plat/fb-s3c2410.h create mode 100644 arch/arm/plat-samsung/include/plat/fb.h create mode 100644 arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h create mode 100644 arch/arm/plat-samsung/include/plat/gpio-cfg.h create mode 100644 arch/arm/plat-samsung/include/plat/gpio-core.h create mode 100644 arch/arm/plat-samsung/include/plat/iic-core.h create mode 100644 arch/arm/plat-samsung/include/plat/irq-uart.h create mode 100644 arch/arm/plat-samsung/include/plat/keypad-core.h create mode 100644 arch/arm/plat-samsung/include/plat/keypad.h create mode 100644 arch/arm/plat-samsung/include/plat/map-base.h create mode 100644 arch/arm/plat-samsung/include/plat/map-s3c.h create mode 100644 arch/arm/plat-samsung/include/plat/map-s5p.h create mode 100644 arch/arm/plat-samsung/include/plat/nand-core.h create mode 100644 arch/arm/plat-samsung/include/plat/onenand-core.h create mode 100644 arch/arm/plat-samsung/include/plat/pm-common.h create mode 100644 arch/arm/plat-samsung/include/plat/pm.h create mode 100644 arch/arm/plat-samsung/include/plat/pwm-core.h create mode 100644 arch/arm/plat-samsung/include/plat/regs-adc.h create mode 100644 arch/arm/plat-samsung/include/plat/regs-irqtype.h create mode 100644 arch/arm/plat-samsung/include/plat/regs-spi.h create mode 100644 arch/arm/plat-samsung/include/plat/regs-srom.h create mode 100644 arch/arm/plat-samsung/include/plat/regs-udc.h create mode 100644 arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h create mode 100644 arch/arm/plat-samsung/include/plat/samsung-time.h create mode 100644 arch/arm/plat-samsung/include/plat/sdhci.h create mode 100644 arch/arm/plat-samsung/include/plat/spi-core.h create mode 100644 arch/arm/plat-samsung/include/plat/usb-phy.h create mode 100644 arch/arm/plat-samsung/include/plat/wakeup-mask.h create mode 100644 arch/arm/plat-samsung/include/plat/watchdog-reset.h (limited to 'arch/arm/plat-samsung/include/plat') diff --git a/arch/arm/plat-samsung/include/plat/adc-core.h b/arch/arm/plat-samsung/include/plat/adc-core.h new file mode 100644 index 000000000..a927bee55 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/adc-core.h @@ -0,0 +1,28 @@ +/* linux/arch/arm/plat-samsung/include/plat/adc-core.h + * + * Copyright (c) 2010 Samsung Electronics Co., Ltd. + * http://www.samsung.com/ + * + * Samsung ADC Controller core functions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_PLAT_ADC_CORE_H +#define __ASM_PLAT_ADC_CORE_H __FILE__ + +/* These functions are only for use with the core support code, such as + * the cpu specific initialisation code + */ + +/* re-define device name depending on support. */ +static inline void s3c_adc_setname(char *name) +{ +#if defined(CONFIG_SAMSUNG_DEV_ADC) || defined(CONFIG_PLAT_S3C24XX) + s3c_device_adc.name = name; +#endif +} + +#endif /* __ASM_PLAT_ADC_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/adc.h b/arch/arm/plat-samsung/include/plat/adc.h new file mode 100644 index 000000000..2fc893155 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/adc.h @@ -0,0 +1,36 @@ +/* arch/arm/plat-samsung/include/plat/adc.h + * + * Copyright (c) 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C ADC driver information + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_PLAT_ADC_H +#define __ASM_PLAT_ADC_H __FILE__ + +struct s3c_adc_client; +struct platform_device; + +extern int s3c_adc_start(struct s3c_adc_client *client, + unsigned int channel, unsigned int nr_samples); + +extern int s3c_adc_read(struct s3c_adc_client *client, unsigned int ch); + +extern struct s3c_adc_client * + s3c_adc_register(struct platform_device *pdev, + void (*select)(struct s3c_adc_client *client, + unsigned selected), + void (*conv)(struct s3c_adc_client *client, + unsigned d0, unsigned d1, + unsigned *samples_left), + unsigned int is_ts); + +extern void s3c_adc_release(struct s3c_adc_client *client); + +#endif /* __ASM_PLAT_ADC_H */ diff --git a/arch/arm/plat-samsung/include/plat/ata-core.h b/arch/arm/plat-samsung/include/plat/ata-core.h new file mode 100644 index 000000000..f5a4ec714 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/ata-core.h @@ -0,0 +1,28 @@ +/* linux/arch/arm/plat-samsung/include/plat/ata-core.h + * + * Copyright (c) 2010 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Samsung CF-ATA Controller core functions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_PLAT_ATA_CORE_H +#define __ASM_PLAT_ATA_CORE_H __FILE__ + +/* These functions are only for use with the core support code, such as + * the cpu specific initialisation code +*/ + +/* re-define device name depending on support. */ +static inline void s3c_cfcon_setname(char *name) +{ +#ifdef CONFIG_SAMSUNG_DEV_IDE + s3c_device_cfcon.name = name; +#endif +} + +#endif /* __ASM_PLAT_ATA_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/backlight.h b/arch/arm/plat-samsung/include/plat/backlight.h new file mode 100644 index 000000000..ad530c78f --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/backlight.h @@ -0,0 +1,26 @@ +/* linux/arch/arm/plat-samsung/include/plat/backlight.h + * + * Copyright (c) 2011 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_PLAT_BACKLIGHT_H +#define __ASM_PLAT_BACKLIGHT_H __FILE__ + +/* samsung_bl_gpio_info - GPIO info for PWM Backlight control + * @no: GPIO number for PWM timer out + * @func: Special function of GPIO line for PWM timer + */ +struct samsung_bl_gpio_info { + int no; + int func; +}; + +extern void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info, + struct platform_pwm_backlight_data *bl_data); + +#endif /* __ASM_PLAT_BACKLIGHT_H */ diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h new file mode 100644 index 000000000..317c52303 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h @@ -0,0 +1,291 @@ +/* arch/arm/plat-samsung/include/plat/cpu-freq-core.h + * + * Copyright (c) 2006-2009 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C CPU frequency scaling support - core support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include + +struct seq_file; + +#define MAX_BANKS (8) +#define S3C2412_MAX_IO (8) + +/** + * struct s3c2410_iobank_timing - IO bank timings for S3C2410 style timings + * @bankcon: The cached version of settings in this structure. + * @tacp: + * @tacs: Time from address valid to nCS asserted. + * @tcos: Time from nCS asserted to nOE or nWE asserted. + * @tacc: Time that nOE or nWE is asserted. + * @tcoh: Time nCS is held after nOE or nWE are released. + * @tcah: Time address is held for after + * @nwait_en: Whether nWAIT is enabled for this bank. + * + * This structure represents the IO timings for a S3C2410 style IO bank + * used by the CPU frequency support if it needs to change the settings + * of the IO. + */ +struct s3c2410_iobank_timing { + unsigned long bankcon; + unsigned int tacp; + unsigned int tacs; + unsigned int tcos; + unsigned int tacc; + unsigned int tcoh; /* nCS hold afrer nOE/nWE */ + unsigned int tcah; /* Address hold after nCS */ + unsigned char nwait_en; /* nWait enabled for bank. */ +}; + +/** + * struct s3c2412_iobank_timing - io timings for PL092 (S3C2412) style IO + * @idcy: The idle cycle time between transactions. + * @wstrd: nCS release to end of read cycle. + * @wstwr: nCS release to end of write cycle. + * @wstoen: nCS assertion to nOE assertion time. + * @wstwen: nCS assertion to nWE assertion time. + * @wstbrd: Burst ready delay. + * @smbidcyr: Register cache for smbidcyr value. + * @smbwstrd: Register cache for smbwstrd value. + * @smbwstwr: Register cache for smbwstwr value. + * @smbwstoen: Register cache for smbwstoen value. + * @smbwstwen: Register cache for smbwstwen value. + * @smbwstbrd: Register cache for smbwstbrd value. + * + * Timing information for a IO bank on an S3C2412 or similar system which + * uses a PL093 block. + */ +struct s3c2412_iobank_timing { + unsigned int idcy; + unsigned int wstrd; + unsigned int wstwr; + unsigned int wstoen; + unsigned int wstwen; + unsigned int wstbrd; + + /* register cache */ + unsigned char smbidcyr; + unsigned char smbwstrd; + unsigned char smbwstwr; + unsigned char smbwstoen; + unsigned char smbwstwen; + unsigned char smbwstbrd; +}; + +union s3c_iobank { + struct s3c2410_iobank_timing *io_2410; + struct s3c2412_iobank_timing *io_2412; +}; + +/** + * struct s3c_iotimings - Chip IO timings holder + * @bank: The timings for each IO bank. + */ +struct s3c_iotimings { + union s3c_iobank bank[MAX_BANKS]; +}; + +/** + * struct s3c_plltab - PLL table information. + * @vals: List of PLL values. + * @size: Size of the PLL table @vals. + */ +struct s3c_plltab { + struct s3c_pllval *vals; + int size; +}; + +/** + * struct s3c_cpufreq_config - current cpu frequency configuration + * @freq: The current settings for the core clocks. + * @max: Maxium settings, derived from core, board and user settings. + * @pll: The PLL table entry for the current PLL settings. + * @divs: The divisor settings for the core clocks. + * @info: The current core driver information. + * @board: The information for the board we are running on. + * @lock_pll: Set if the PLL settings cannot be changed. + * + * This is for the core drivers that need to know information about + * the current settings and values. It should not be needed by any + * device drivers. +*/ +struct s3c_cpufreq_config { + struct s3c_freq freq; + struct s3c_freq max; + struct clk *mpll; + struct cpufreq_frequency_table pll; + struct s3c_clkdivs divs; + struct s3c_cpufreq_info *info; /* for core, not drivers */ + struct s3c_cpufreq_board *board; + + unsigned int lock_pll:1; +}; + +/** + * struct s3c_cpufreq_info - Information for the CPU frequency driver. + * @name: The name of this implementation. + * @max: The maximum frequencies for the system. + * @latency: Transition latency to give to cpufreq. + * @locktime_m: The lock-time in uS for the MPLL. + * @locktime_u: The lock-time in uS for the UPLL. + * @locttime_bits: The number of bits each LOCKTIME field. + * @need_pll: Set if this driver needs to change the PLL values to achieve + * any frequency changes. This is really only need by devices like the + * S3C2410 where there is no or limited divider between the PLL and the + * ARMCLK. + * @get_iotiming: Get the current IO timing data, mainly for use at start. + * @set_iotiming: Update the IO timings from the cached copies calculated + * from the @calc_iotiming entry when changing the frequency. + * @calc_iotiming: Calculate and update the cached copies of the IO timings + * from the newly calculated frequencies. + * @calc_freqtable: Calculate (fill in) the given frequency table from the + * current frequency configuration. If the table passed in is NULL, + * then the return is the number of elements to be filled for allocation + * of the table. + * @set_refresh: Set the memory refresh configuration. + * @set_fvco: Set the PLL frequencies. + * @set_divs: Update the clock divisors. + * @calc_divs: Calculate the clock divisors. + */ +struct s3c_cpufreq_info { + const char *name; + struct s3c_freq max; + + unsigned int latency; + + unsigned int locktime_m; + unsigned int locktime_u; + unsigned char locktime_bits; + + unsigned int need_pll:1; + + /* driver routines */ + + int (*get_iotiming)(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + + void (*set_iotiming)(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + + int (*calc_iotiming)(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + + int (*calc_freqtable)(struct s3c_cpufreq_config *cfg, + struct cpufreq_frequency_table *t, + size_t table_size); + + void (*debug_io_show)(struct seq_file *seq, + struct s3c_cpufreq_config *cfg, + union s3c_iobank *iob); + + void (*set_refresh)(struct s3c_cpufreq_config *cfg); + void (*set_fvco)(struct s3c_cpufreq_config *cfg); + void (*set_divs)(struct s3c_cpufreq_config *cfg); + int (*calc_divs)(struct s3c_cpufreq_config *cfg); +}; + +extern int s3c_cpufreq_register(struct s3c_cpufreq_info *info); + +extern int s3c_plltab_register(struct cpufreq_frequency_table *plls, + unsigned int plls_no); + +/* exports and utilities for debugfs */ +extern struct s3c_cpufreq_config *s3c_cpufreq_getconfig(void); +extern struct s3c_iotimings *s3c_cpufreq_getiotimings(void); + +#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_DEBUGFS +#define s3c_cpufreq_debugfs_call(x) x +#else +#define s3c_cpufreq_debugfs_call(x) NULL +#endif + +/* Useful utility functions. */ + +extern struct clk *s3c_cpufreq_clk_get(struct device *, const char *); + +/* S3C2410 and compatible exported functions */ + +extern void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg); +extern void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg); + +#ifdef CONFIG_S3C2410_IOTIMING +extern void s3c2410_iotiming_debugfs(struct seq_file *seq, + struct s3c_cpufreq_config *cfg, + union s3c_iobank *iob); + +extern int s3c2410_iotiming_calc(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot); + +extern int s3c2410_iotiming_get(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + +extern void s3c2410_iotiming_set(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot); +#else +#define s3c2410_iotiming_debugfs NULL +#define s3c2410_iotiming_calc NULL +#define s3c2410_iotiming_get NULL +#define s3c2410_iotiming_set NULL +#endif /* CONFIG_S3C2410_IOTIMING */ + +/* S3C2412 compatible routines */ + +#ifdef CONFIG_S3C2412_IOTIMING +extern void s3c2412_iotiming_debugfs(struct seq_file *seq, + struct s3c_cpufreq_config *cfg, + union s3c_iobank *iob); + +extern int s3c2412_iotiming_get(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + +extern int s3c2412_iotiming_calc(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot); + +extern void s3c2412_iotiming_set(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot); +#else +#define s3c2412_iotiming_debugfs NULL +#define s3c2412_iotiming_calc NULL +#define s3c2412_iotiming_get NULL +#define s3c2412_iotiming_set NULL +#endif /* CONFIG_S3C2412_IOTIMING */ + +#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_DEBUG +#define s3c_freq_dbg(x...) printk(KERN_INFO x) +#else +#define s3c_freq_dbg(x...) do { if (0) printk(x); } while (0) +#endif /* CONFIG_ARM_S3C24XX_CPUFREQ_DEBUG */ + +#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_IODEBUG +#define s3c_freq_iodbg(x...) printk(KERN_INFO x) +#else +#define s3c_freq_iodbg(x...) do { if (0) printk(x); } while (0) +#endif /* CONFIG_ARM_S3C24XX_CPUFREQ_IODEBUG */ + +static inline int s3c_cpufreq_addfreq(struct cpufreq_frequency_table *table, + int index, size_t table_size, + unsigned int freq) +{ + if (index < 0) + return index; + + if (table) { + if (index >= table_size) + return -ENOMEM; + + s3c_freq_dbg("%s: { %d = %u kHz }\n", + __func__, index, freq); + + table[index].driver_data = index; + table[index].frequency = freq; + } + + return index + 1; +} diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq.h b/arch/arm/plat-samsung/include/plat/cpu-freq.h new file mode 100644 index 000000000..85517ab96 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/cpu-freq.h @@ -0,0 +1,145 @@ +/* arch/arm/plat-samsung/include/plat/cpu-freq.h + * + * Copyright (c) 2006-2007 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C CPU frequency scaling support - driver and board + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include + +struct s3c_cpufreq_info; +struct s3c_cpufreq_board; +struct s3c_iotimings; + +/** + * struct s3c_freq - frequency information (mainly for core drivers) + * @fclk: The FCLK frequency in Hz. + * @armclk: The ARMCLK frequency in Hz. + * @hclk_tns: HCLK cycle time in 10ths of nano-seconds. + * @hclk: The HCLK frequency in Hz. + * @pclk: The PCLK frequency in Hz. + * + * This contains the frequency information about the current configuration + * mainly for the core drivers to ensure we do not end up passing about + * a large number of parameters. + * + * The @hclk_tns field is a useful cache for the parts of the drivers that + * need to calculate IO timings and suchlike. + */ +struct s3c_freq { + unsigned long fclk; + unsigned long armclk; + unsigned long hclk_tns; /* in 10ths of ns */ + unsigned long hclk; + unsigned long pclk; +}; + +/** + * struct s3c_cpufreq_freqs - s3c cpufreq notification information. + * @freqs: The cpufreq setting information. + * @old: The old clock settings. + * @new: The new clock settings. + * @pll_changing: Set if the PLL is changing. + * + * Wrapper 'struct cpufreq_freqs' so that any drivers receiving the + * notification can use this information that is not provided by just + * having the core frequency alone. + * + * The pll_changing flag is used to indicate if the PLL itself is + * being set during this change. This is important as the clocks + * will temporarily be set to the XTAL clock during this time, so + * drivers may want to close down their output during this time. + * + * Note, this is not being used by any current drivers and therefore + * may be removed in the future. + */ +struct s3c_cpufreq_freqs { + struct cpufreq_freqs freqs; + struct s3c_freq old; + struct s3c_freq new; + + unsigned int pll_changing:1; +}; + +#define to_s3c_cpufreq(_cf) container_of(_cf, struct s3c_cpufreq_freqs, freqs) + +/** + * struct s3c_clkdivs - clock divisor information + * @p_divisor: Divisor from FCLK to PCLK. + * @h_divisor: Divisor from FCLK to HCLK. + * @arm_divisor: Divisor from FCLK to ARMCLK (not all CPUs). + * @dvs: Non-zero if using DVS mode for ARMCLK. + * + * Divisor settings for the core clocks. + */ +struct s3c_clkdivs { + int p_divisor; + int h_divisor; + int arm_divisor; + unsigned char dvs; +}; + +#define PLLVAL(_m, _p, _s) (((_m) << 12) | ((_p) << 4) | (_s)) + +/** + * struct s3c_pllval - PLL value entry. + * @freq: The frequency for this entry in Hz. + * @pll_reg: The PLL register setting for this PLL value. + */ +struct s3c_pllval { + unsigned long freq; + unsigned long pll_reg; +}; + +/** + * struct s3c_cpufreq_board - per-board cpu frequency informatin + * @refresh: The SDRAM refresh period in nanoseconds. + * @auto_io: Set if the IO timing settings should be generated from the + * initialisation time hardware registers. + * @need_io: Set if the board has external IO on any of the chipselect + * lines that will require the hardware timing registers to be + * updated on a clock change. + * @max: The maxium frequency limits for the system. Any field that + * is left at zero will use the CPU's settings. + * + * This contains the board specific settings that affect how the CPU + * drivers chose settings. These include the memory refresh and IO + * timing information. + * + * Registration depends on the driver being used, the ARMCLK only + * implementation does not currently need this but the older style + * driver requires this to be available. + */ +struct s3c_cpufreq_board { + unsigned int refresh; + unsigned int auto_io:1; /* automatically init io timings. */ + unsigned int need_io:1; /* set if needs io timing support. */ + + /* any non-zero field in here is taken as an upper limit. */ + struct s3c_freq max; /* frequency limits */ +}; + +/* Things depending on frequency scaling. */ +#ifdef CONFIG_ARM_S3C_CPUFREQ +#define __init_or_cpufreq +#else +#define __init_or_cpufreq __init +#endif + +/* Board functions */ + +#ifdef CONFIG_ARM_S3C_CPUFREQ +extern int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board); +#else + +static inline int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board) +{ + return 0; +} +#endif /* CONFIG_ARM_S3C_CPUFREQ */ diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/plat-samsung/include/plat/cpu.h new file mode 100644 index 000000000..61d14f3a0 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/cpu.h @@ -0,0 +1,143 @@ +/* linux/arch/arm/plat-samsung/include/plat/cpu.h + * + * Copyright (c) 2011 Samsung Electronics Co., Ltd. + * http://www.samsung.com/ + * + * Copyright (c) 2004-2005 Simtec Electronics + * Ben Dooks + * + * Header file for Samsung CPU support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* todo - fix when rmk changes iodescs to use `void __iomem *` */ + +#ifndef __SAMSUNG_PLAT_CPU_H +#define __SAMSUNG_PLAT_CPU_H + +extern unsigned long samsung_cpu_id; + +#define S3C2410_CPU_ID 0x32410000 +#define S3C2410_CPU_MASK 0xFFFFFFFF + +#define S3C24XX_CPU_ID 0x32400000 +#define S3C24XX_CPU_MASK 0xFFF00000 + +#define S3C2412_CPU_ID 0x32412000 +#define S3C2412_CPU_MASK 0xFFFFF000 + +#define S3C6400_CPU_ID 0x36400000 +#define S3C6410_CPU_ID 0x36410000 +#define S3C64XX_CPU_MASK 0xFFFFF000 + +#define S5PV210_CPU_ID 0x43110000 +#define S5PV210_CPU_MASK 0xFFFFF000 + +#define IS_SAMSUNG_CPU(name, id, mask) \ +static inline int is_samsung_##name(void) \ +{ \ + return ((samsung_cpu_id & mask) == (id & mask)); \ +} + +IS_SAMSUNG_CPU(s3c2410, S3C2410_CPU_ID, S3C2410_CPU_MASK) +IS_SAMSUNG_CPU(s3c24xx, S3C24XX_CPU_ID, S3C24XX_CPU_MASK) +IS_SAMSUNG_CPU(s3c2412, S3C2412_CPU_ID, S3C2412_CPU_MASK) +IS_SAMSUNG_CPU(s3c6400, S3C6400_CPU_ID, S3C64XX_CPU_MASK) +IS_SAMSUNG_CPU(s3c6410, S3C6410_CPU_ID, S3C64XX_CPU_MASK) + +#if defined(CONFIG_CPU_S3C2410) || defined(CONFIG_CPU_S3C2412) || \ + defined(CONFIG_CPU_S3C2416) || defined(CONFIG_CPU_S3C2440) || \ + defined(CONFIG_CPU_S3C2442) || defined(CONFIG_CPU_S3C244X) || \ + defined(CONFIG_CPU_S3C2443) +# define soc_is_s3c24xx() is_samsung_s3c24xx() +# define soc_is_s3c2410() is_samsung_s3c2410() +#else +# define soc_is_s3c24xx() 0 +# define soc_is_s3c2410() 0 +#endif + +#if defined(CONFIG_CPU_S3C2412) +# define soc_is_s3c2412() is_samsung_s3c2412() +#else +# define soc_is_s3c2412() 0 +#endif + +#if defined(CONFIG_CPU_S3C6400) || defined(CONFIG_CPU_S3C6410) +# define soc_is_s3c6400() is_samsung_s3c6400() +# define soc_is_s3c6410() is_samsung_s3c6410() +# define soc_is_s3c64xx() (is_samsung_s3c6400() || is_samsung_s3c6410()) +#else +# define soc_is_s3c6400() 0 +# define soc_is_s3c6410() 0 +# define soc_is_s3c64xx() 0 +#endif + +#define IODESC_ENT(x) { (unsigned long)S3C24XX_VA_##x, __phys_to_pfn(S3C24XX_PA_##x), S3C24XX_SZ_##x, MT_DEVICE } + +#ifndef KHZ +#define KHZ (1000) +#endif + +#ifndef MHZ +#define MHZ (1000*1000) +#endif + +#define print_mhz(m) ((m) / MHZ), (((m) / 1000) % 1000) + +/* forward declaration */ +struct s3c24xx_uart_resources; +struct platform_device; +struct s3c2410_uartcfg; +struct map_desc; + +/* per-cpu initialisation function table. */ + +struct cpu_table { + unsigned long idcode; + unsigned long idmask; + void (*map_io)(void); + void (*init_uarts)(struct s3c2410_uartcfg *cfg, int no); + void (*init_clocks)(int xtal); + int (*init)(void); + const char *name; +}; + +extern void s3c_init_cpu(unsigned long idcode, + struct cpu_table *cpus, unsigned int cputab_size); + +/* core initialisation functions */ + +extern void s3c24xx_init_io(struct map_desc *mach_desc, int size); + +extern void s3c64xx_init_cpu(void); + +extern unsigned int samsung_rev(void); + +extern void s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no); + +extern void s3c24xx_init_clocks(int xtal); + +extern void s3c24xx_init_uartdevs(char *name, + struct s3c24xx_uart_resources *res, + struct s3c2410_uartcfg *cfg, int no); + +extern struct syscore_ops s3c2410_pm_syscore_ops; +extern struct syscore_ops s3c2412_pm_syscore_ops; +extern struct syscore_ops s3c2416_pm_syscore_ops; +extern struct syscore_ops s3c244x_pm_syscore_ops; + +/* system device subsystems */ + +extern struct bus_type s3c2410_subsys; +extern struct bus_type s3c2410a_subsys; +extern struct bus_type s3c2412_subsys; +extern struct bus_type s3c2416_subsys; +extern struct bus_type s3c2440_subsys; +extern struct bus_type s3c2442_subsys; +extern struct bus_type s3c2443_subsys; +extern struct bus_type s3c6410_subsys; + +#endif diff --git a/arch/arm/plat-samsung/include/plat/devs.h b/arch/arm/plat-samsung/include/plat/devs.h new file mode 100644 index 000000000..e23fed311 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/devs.h @@ -0,0 +1,100 @@ +/* arch/arm/plat-samsung/include/plat/devs.h + * + * Copyright (c) 2011 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Copyright (c) 2004 Simtec Electronics + * Ben Dooks + * + * Header file for s3c2410 standard platform devices + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_DEVS_H +#define __PLAT_DEVS_H __FILE__ + +#include + +struct s3c24xx_uart_resources { + struct resource *resources; + unsigned long nr_resources; +}; + +extern struct s3c24xx_uart_resources s3c2410_uart_resources[]; +extern struct s3c24xx_uart_resources s3c64xx_uart_resources[]; + +extern struct platform_device *s3c24xx_uart_devs[]; +extern struct platform_device *s3c24xx_uart_src[]; + +extern struct platform_device s3c64xx_device_ac97; +extern struct platform_device s3c64xx_device_iis0; +extern struct platform_device s3c64xx_device_iis1; +extern struct platform_device s3c64xx_device_iisv4; +extern struct platform_device s3c64xx_device_onenand1; +extern struct platform_device s3c64xx_device_pcm0; +extern struct platform_device s3c64xx_device_pcm1; +extern struct platform_device s3c64xx_device_spi0; +extern struct platform_device s3c64xx_device_spi1; +extern struct platform_device s3c64xx_device_spi2; + +extern struct platform_device s3c_device_adc; +extern struct platform_device s3c_device_cfcon; +extern struct platform_device s3c_device_fb; +extern struct platform_device s3c_device_hwmon; +extern struct platform_device s3c_device_hsmmc0; +extern struct platform_device s3c_device_hsmmc1; +extern struct platform_device s3c_device_hsmmc2; +extern struct platform_device s3c_device_hsmmc3; +extern struct platform_device s3c_device_i2c0; +extern struct platform_device s3c_device_i2c1; +extern struct platform_device s3c_device_i2c2; +extern struct platform_device s3c_device_i2c3; +extern struct platform_device s3c_device_i2c4; +extern struct platform_device s3c_device_i2c5; +extern struct platform_device s3c_device_i2c6; +extern struct platform_device s3c_device_i2c7; +extern struct platform_device s3c_device_iis; +extern struct platform_device s3c_device_lcd; +extern struct platform_device s3c_device_nand; +extern struct platform_device s3c_device_ohci; +extern struct platform_device s3c_device_onenand; +extern struct platform_device s3c_device_rtc; +extern struct platform_device s3c_device_sdi; +extern struct platform_device s3c_device_spi0; +extern struct platform_device s3c_device_spi1; +extern struct platform_device s3c_device_ts; +extern struct platform_device s3c_device_timer[]; +extern struct platform_device s3c_device_usbgadget; +extern struct platform_device s3c_device_usb_hsotg; +extern struct platform_device s3c_device_usb_hsudc; +extern struct platform_device s3c_device_wdt; + +extern struct platform_device samsung_asoc_idma; +extern struct platform_device samsung_device_keypad; +extern struct platform_device samsung_device_pwm; + +/* s3c2440 specific devices */ + +#ifdef CONFIG_CPU_S3C2440 + +extern struct platform_device s3c_device_camif; +extern struct platform_device s3c_device_ac97; + +#endif + +/** + * s3c_set_platdata() - helper for setting platform data + * @pd: The default platform data for this device. + * @pdsize: The size of the platform data. + * @pdev: Pointer to the device to fill in. + * + * This helper replaces a number of calls that copy and then set the + * platform data of the device. + */ +extern void *s3c_set_platdata(void *pd, size_t pdsize, + struct platform_device *pdev); + +#endif /* __PLAT_DEVS_H */ diff --git a/arch/arm/plat-samsung/include/plat/fb-core.h b/arch/arm/plat-samsung/include/plat/fb-core.h new file mode 100644 index 000000000..bca383efc --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/fb-core.h @@ -0,0 +1,29 @@ +/* + * arch/arm/plat-samsung/include/plat/fb-core.h + * + * Copyright 2010 Samsung Electronics Co., Ltd. + * Pawel Osciak + * + * Samsung framebuffer driver core functions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __ASM_PLAT_FB_CORE_H +#define __ASM_PLAT_FB_CORE_H __FILE__ + +/* + * These functions are only for use with the core support code, such as + * the CPU-specific initialization code. + */ + +/* Re-define device name depending on support. */ +static inline void s3c_fb_setname(char *name) +{ +#ifdef CONFIG_S3C_DEV_FB + s3c_device_fb.name = name; +#endif +} + +#endif /* __ASM_PLAT_FB_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/fb-s3c2410.h b/arch/arm/plat-samsung/include/plat/fb-s3c2410.h new file mode 100644 index 000000000..4e5d9588b --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/fb-s3c2410.h @@ -0,0 +1,72 @@ +/* arch/arm/plat-samsung/include/plat/fb-s3c2410.h + * + * Copyright (c) 2004 Arnaud Patard + * + * Inspired by pxafb.h + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_PLAT_FB_S3C2410_H +#define __ASM_PLAT_FB_S3C2410_H __FILE__ + +struct s3c2410fb_hw { + unsigned long lcdcon1; + unsigned long lcdcon2; + unsigned long lcdcon3; + unsigned long lcdcon4; + unsigned long lcdcon5; +}; + +/* LCD description */ +struct s3c2410fb_display { + /* LCD type */ + unsigned type; + + /* Screen size */ + unsigned short width; + unsigned short height; + + /* Screen info */ + unsigned short xres; + unsigned short yres; + unsigned short bpp; + + unsigned pixclock; /* pixclock in picoseconds */ + unsigned short left_margin; /* value in pixels (TFT) or HCLKs (STN) */ + unsigned short right_margin; /* value in pixels (TFT) or HCLKs (STN) */ + unsigned short hsync_len; /* value in pixels (TFT) or HCLKs (STN) */ + unsigned short upper_margin; /* value in lines (TFT) or 0 (STN) */ + unsigned short lower_margin; /* value in lines (TFT) or 0 (STN) */ + unsigned short vsync_len; /* value in lines (TFT) or 0 (STN) */ + + /* lcd configuration registers */ + unsigned long lcdcon5; +}; + +struct s3c2410fb_mach_info { + + struct s3c2410fb_display *displays; /* attached diplays info */ + unsigned num_displays; /* number of defined displays */ + unsigned default_display; + + /* GPIOs */ + + unsigned long gpcup; + unsigned long gpcup_mask; + unsigned long gpccon; + unsigned long gpccon_mask; + unsigned long gpdup; + unsigned long gpdup_mask; + unsigned long gpdcon; + unsigned long gpdcon_mask; + + /* lpc3600 control register */ + unsigned long lpcsel; +}; + +extern void __init s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *); + +#endif /* __ASM_PLAT_FB_S3C2410_H */ diff --git a/arch/arm/plat-samsung/include/plat/fb.h b/arch/arm/plat-samsung/include/plat/fb.h new file mode 100644 index 000000000..b89f8f208 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/fb.h @@ -0,0 +1,35 @@ +/* arch/arm/plat-samsung/include/plat/fb.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C - FB platform data definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_S3C_FB_H +#define __PLAT_S3C_FB_H __FILE__ + +#include + +/** + * s3c_fb_set_platdata() - Setup the FB device with platform data. + * @pd: The platform data to set. The data is copied from the passed structure + * so the machine data can mark the data __initdata so that any unused + * machines will end up dumping their data at runtime. + */ +extern void s3c_fb_set_platdata(struct s3c_fb_platdata *pd); + +/** + * s3c64xx_fb_gpio_setup_24bpp() - S3C64XX setup function for 24bpp LCD + * + * Initialise the GPIO for an 24bpp LCD display on the RGB interface. + */ +extern void s3c64xx_fb_gpio_setup_24bpp(void); + +#endif /* __PLAT_S3C_FB_H */ diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h b/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h new file mode 100644 index 000000000..a181d7ce8 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h @@ -0,0 +1,163 @@ +/* linux/arch/arm/plat-samsung/include/plat/gpio-cfg-helper.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * Samsung Platform - GPIO pin configuration helper definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* This is meant for core cpu support, machine or other driver files + * should not be including this header. + */ + +#ifndef __PLAT_GPIO_CFG_HELPERS_H +#define __PLAT_GPIO_CFG_HELPERS_H __FILE__ + +/* As a note, all gpio configuration functions are entered exclusively, either + * with the relevant lock held or the system prevented from doing anything else + * by disabling interrupts. +*/ + +static inline int samsung_gpio_do_setcfg(struct samsung_gpio_chip *chip, + unsigned int off, unsigned int config) +{ + return (chip->config->set_config)(chip, off, config); +} + +static inline unsigned samsung_gpio_do_getcfg(struct samsung_gpio_chip *chip, + unsigned int off) +{ + return (chip->config->get_config)(chip, off); +} + +static inline int samsung_gpio_do_setpull(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull) +{ + return (chip->config->set_pull)(chip, off, pull); +} + +static inline samsung_gpio_pull_t samsung_gpio_do_getpull(struct samsung_gpio_chip *chip, + unsigned int off) +{ + return chip->config->get_pull(chip, off); +} + +/* Pull-{up,down} resistor controls. + * + * S3C2410,S3C2440 = Pull-UP, + * S3C2412,S3C2413 = Pull-Down + * S3C6400,S3C6410 = Pull-Both [None,Down,Up,Undef] + * S3C2443 = Pull-Both [not same as S3C6400] + */ + +/** + * s3c24xx_gpio_setpull_1up() - Pull configuration for choice of up or none. + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * @param: pull: The pull mode being requested. + * + * This is a helper function for the case where we have GPIOs with one + * bit configuring the presence of a pull-up resistor. + */ +extern int s3c24xx_gpio_setpull_1up(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull); + +/** + * s3c24xx_gpio_setpull_1down() - Pull configuration for choice of down or none + * @chip: The gpio chip that is being configured + * @off: The offset for the GPIO being configured + * @param: pull: The pull mode being requested + * + * This is a helper function for the case where we have GPIOs with one + * bit configuring the presence of a pull-down resistor. + */ +extern int s3c24xx_gpio_setpull_1down(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull); + +/** + * samsung_gpio_setpull_upown() - Pull configuration for choice of up, + * down or none + * + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * @param: pull: The pull mode being requested. + * + * This is a helper function for the case where we have GPIOs with two + * bits configuring the presence of a pull resistor, in the following + * order: + * 00 = No pull resistor connected + * 01 = Pull-up resistor connected + * 10 = Pull-down resistor connected + */ +extern int samsung_gpio_setpull_updown(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull); + +/** + * samsung_gpio_getpull_updown() - Get configuration for choice of up, + * down or none + * + * @chip: The gpio chip that the GPIO pin belongs to + * @off: The offset to the pin to get the configuration of. + * + * This helper function reads the state of the pull-{up,down} resistor + * for the given GPIO in the same case as samsung_gpio_setpull_upown. +*/ +extern samsung_gpio_pull_t samsung_gpio_getpull_updown(struct samsung_gpio_chip *chip, + unsigned int off); + +/** + * s3c24xx_gpio_getpull_1up() - Get configuration for choice of up or none + * @chip: The gpio chip that the GPIO pin belongs to + * @off: The offset to the pin to get the configuration of. + * + * This helper function reads the state of the pull-up resistor for the + * given GPIO in the same case as s3c24xx_gpio_setpull_1up. +*/ +extern samsung_gpio_pull_t s3c24xx_gpio_getpull_1up(struct samsung_gpio_chip *chip, + unsigned int off); + +/** + * s3c24xx_gpio_getpull_1down() - Get configuration for choice of down or none + * @chip: The gpio chip that the GPIO pin belongs to + * @off: The offset to the pin to get the configuration of. + * + * This helper function reads the state of the pull-down resistor for the + * given GPIO in the same case as s3c24xx_gpio_setpull_1down. +*/ +extern samsung_gpio_pull_t s3c24xx_gpio_getpull_1down(struct samsung_gpio_chip *chip, + unsigned int off); + +/** + * s3c2443_gpio_setpull() - Pull configuration for s3c2443. + * @chip: The gpio chip that is being configured. + * @off: The offset for the GPIO being configured. + * @param: pull: The pull mode being requested. + * + * This is a helper function for the case where we have GPIOs with two + * bits configuring the presence of a pull resistor, in the following + * order: + * 00 = Pull-up resistor connected + * 10 = Pull-down resistor connected + * x1 = No pull up resistor + */ +extern int s3c2443_gpio_setpull(struct samsung_gpio_chip *chip, + unsigned int off, samsung_gpio_pull_t pull); + +/** + * s3c2443_gpio_getpull() - Get configuration for s3c2443 pull resistors + * @chip: The gpio chip that the GPIO pin belongs to. + * @off: The offset to the pin to get the configuration of. + * + * This helper function reads the state of the pull-{up,down} resistor for the + * given GPIO in the same case as samsung_gpio_setpull_upown. +*/ +extern samsung_gpio_pull_t s3c2443_gpio_getpull(struct samsung_gpio_chip *chip, + unsigned int off); + +#endif /* __PLAT_GPIO_CFG_HELPERS_H */ diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg.h b/arch/arm/plat-samsung/include/plat/gpio-cfg.h new file mode 100644 index 000000000..b5294eff1 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/gpio-cfg.h @@ -0,0 +1,182 @@ +/* linux/arch/arm/plat-s3c/include/plat/gpio-cfg.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C Platform - GPIO pin configuration + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* This file contains the necessary definitions to get the basic gpio + * pin configuration done such as setting a pin to input or output or + * changing the pull-{up,down} configurations. + */ + +/* Note, this interface is being added to the s3c64xx arch first and will + * be added to the s3c24xx systems later. + */ + +#ifndef __PLAT_GPIO_CFG_H +#define __PLAT_GPIO_CFG_H __FILE__ + +#include + +typedef unsigned int __bitwise__ samsung_gpio_pull_t; + +/* forward declaration if gpio-core.h hasn't been included */ +struct samsung_gpio_chip; + +/** + * struct samsung_gpio_cfg GPIO configuration + * @cfg_eint: Configuration setting when used for external interrupt source + * @get_pull: Read the current pull configuration for the GPIO + * @set_pull: Set the current pull configuraiton for the GPIO + * @set_config: Set the current configuration for the GPIO + * @get_config: Read the current configuration for the GPIO + * + * Each chip can have more than one type of GPIO bank available and some + * have different capabilites even when they have the same control register + * layouts. Provide an point to vector control routine and provide any + * per-bank configuration information that other systems such as the + * external interrupt code will need. + * + * @sa samsung_gpio_cfgpin + * @sa s3c_gpio_getcfg + * @sa s3c_gpio_setpull + * @sa s3c_gpio_getpull + */ +struct samsung_gpio_cfg { + unsigned int cfg_eint; + + samsung_gpio_pull_t (*get_pull)(struct samsung_gpio_chip *chip, unsigned offs); + int (*set_pull)(struct samsung_gpio_chip *chip, unsigned offs, + samsung_gpio_pull_t pull); + + unsigned (*get_config)(struct samsung_gpio_chip *chip, unsigned offs); + int (*set_config)(struct samsung_gpio_chip *chip, unsigned offs, + unsigned config); +}; + +#define S3C_GPIO_SPECIAL_MARK (0xfffffff0) +#define S3C_GPIO_SPECIAL(x) (S3C_GPIO_SPECIAL_MARK | (x)) + +/* Defines for generic pin configurations */ +#define S3C_GPIO_INPUT (S3C_GPIO_SPECIAL(0)) +#define S3C_GPIO_OUTPUT (S3C_GPIO_SPECIAL(1)) +#define S3C_GPIO_SFN(x) (S3C_GPIO_SPECIAL(x)) + +#define samsung_gpio_is_cfg_special(_cfg) \ + (((_cfg) & S3C_GPIO_SPECIAL_MARK) == S3C_GPIO_SPECIAL_MARK) + +/** + * s3c_gpio_cfgpin() - Change the GPIO function of a pin. + * @pin pin The pin number to configure. + * @to to The configuration for the pin's function. + * + * Configure which function is actually connected to the external + * pin, such as an gpio input, output or some form of special function + * connected to an internal peripheral block. + * + * The @to parameter can be one of the generic S3C_GPIO_INPUT, S3C_GPIO_OUTPUT + * or S3C_GPIO_SFN() to indicate one of the possible values that the helper + * will then generate the correct bit mask and shift for the configuration. + * + * If a bank of GPIOs all needs to be set to special-function 2, then + * the following code will work: + * + * for (gpio = start; gpio < end; gpio++) + * s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2)); + * + * The @to parameter can also be a specific value already shifted to the + * correct position in the control register, although these are discouraged + * in newer kernels and are only being kept for compatibility. + */ +extern int s3c_gpio_cfgpin(unsigned int pin, unsigned int to); + +/** + * s3c_gpio_getcfg - Read the current function for a GPIO pin + * @pin: The pin to read the configuration value for. + * + * Read the configuration state of the given @pin, returning a value that + * could be passed back to s3c_gpio_cfgpin(). + * + * @sa s3c_gpio_cfgpin + */ +extern unsigned s3c_gpio_getcfg(unsigned int pin); + +/** + * s3c_gpio_cfgpin_range() - Change the GPIO function for configuring pin range + * @start: The pin number to start at + * @nr: The number of pins to configure from @start. + * @cfg: The configuration for the pin's function + * + * Call s3c_gpio_cfgpin() for the @nr pins starting at @start. + * + * @sa s3c_gpio_cfgpin. + */ +extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr, + unsigned int cfg); + +/* Define values for the pull-{up,down} available for each gpio pin. + * + * These values control the state of the weak pull-{up,down} resistors + * available on most pins on the S3C series. Not all chips support both + * up or down settings, and it may be dependent on the chip that is being + * used to whether the particular mode is available. + */ +#define S3C_GPIO_PULL_NONE ((__force samsung_gpio_pull_t)0x00) +#define S3C_GPIO_PULL_DOWN ((__force samsung_gpio_pull_t)0x01) +#define S3C_GPIO_PULL_UP ((__force samsung_gpio_pull_t)0x02) + +/** + * s3c_gpio_setpull() - set the state of a gpio pin pull resistor + * @pin: The pin number to configure the pull resistor. + * @pull: The configuration for the pull resistor. + * + * This function sets the state of the pull-{up,down} resistor for the + * specified pin. It will return 0 if successful, or a negative error + * code if the pin cannot support the requested pull setting. + * + * @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP. +*/ +extern int s3c_gpio_setpull(unsigned int pin, samsung_gpio_pull_t pull); + +/** + * s3c_gpio_getpull() - get the pull resistor state of a gpio pin + * @pin: The pin number to get the settings for + * + * Read the pull resistor value for the specified pin. +*/ +extern samsung_gpio_pull_t s3c_gpio_getpull(unsigned int pin); + +/* configure `all` aspects of an gpio */ + +/** + * s3c_gpio_cfgall_range() - configure range of gpio functtion and pull. + * @start: The gpio number to start at. + * @nr: The number of gpio to configure from @start. + * @cfg: The configuration to use + * @pull: The pull setting to use. + * + * Run s3c_gpio_cfgpin() and s3c_gpio_setpull() over the gpio range starting + * @gpio and running for @size. + * + * @sa s3c_gpio_cfgpin + * @sa s3c_gpio_setpull + * @sa s3c_gpio_cfgpin_range + */ +extern int s3c_gpio_cfgall_range(unsigned int start, unsigned int nr, + unsigned int cfg, samsung_gpio_pull_t pull); + +static inline int s3c_gpio_cfgrange_nopull(unsigned int pin, unsigned int size, + unsigned int cfg) +{ + return s3c_gpio_cfgall_range(pin, size, cfg, S3C_GPIO_PULL_NONE); +} + +#endif /* __PLAT_GPIO_CFG_H */ diff --git a/arch/arm/plat-samsung/include/plat/gpio-core.h b/arch/arm/plat-samsung/include/plat/gpio-core.h new file mode 100644 index 000000000..6ce11bfdc --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/gpio-core.h @@ -0,0 +1,145 @@ +/* linux/arch/arm/plat-s3c/include/plat/gpio-core.h + * + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C Platform - GPIO core + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_SAMSUNG_GPIO_CORE_H +#define __PLAT_SAMSUNG_GPIO_CORE_H + +/* Bring in machine-local definitions, especially S3C_GPIO_END */ +#include + +#define GPIOCON_OFF (0x00) +#define GPIODAT_OFF (0x04) + +#define con_4bit_shift(__off) ((__off) * 4) + +/* Define the core gpiolib support functions that the s3c platforms may + * need to extend or change depending on the hardware and the s3c chip + * selected at build or found at run time. + * + * These definitions are not intended for driver inclusion, there is + * nothing here that should not live outside the platform and core + * specific code. +*/ + +struct samsung_gpio_chip; + +/** + * struct samsung_gpio_pm - power management (suspend/resume) information + * @save: Routine to save the state of the GPIO block + * @resume: Routine to resume the GPIO block. + */ +struct samsung_gpio_pm { + void (*save)(struct samsung_gpio_chip *chip); + void (*resume)(struct samsung_gpio_chip *chip); +}; + +struct samsung_gpio_cfg; + +/** + * struct samsung_gpio_chip - wrapper for specific implementation of gpio + * @chip: The chip structure to be exported via gpiolib. + * @base: The base pointer to the gpio configuration registers. + * @group: The group register number for gpio interrupt support. + * @irq_base: The base irq number. + * @config: special function and pull-resistor control information. + * @lock: Lock for exclusive access to this gpio bank. + * @pm_save: Save information for suspend/resume support. + * @bitmap_gpio_int: Bitmap for representing GPIO interrupt or not. + * + * This wrapper provides the necessary information for the Samsung + * specific gpios being registered with gpiolib. + * + * The lock protects each gpio bank from multiple access of the shared + * configuration registers, or from reading of data whilst another thread + * is writing to the register set. + * + * Each chip has its own lock to avoid any contention between different + * CPU cores trying to get one lock for different GPIO banks, where each + * bank of GPIO has its own register space and configuration registers. + */ +struct samsung_gpio_chip { + struct gpio_chip chip; + struct samsung_gpio_cfg *config; + struct samsung_gpio_pm *pm; + void __iomem *base; + int irq_base; + int group; + spinlock_t lock; +#ifdef CONFIG_PM + u32 pm_save[4]; +#endif + u32 bitmap_gpio_int; +}; + +static inline struct samsung_gpio_chip *to_samsung_gpio(struct gpio_chip *gpc) +{ + return container_of(gpc, struct samsung_gpio_chip, chip); +} + +/** + * samsung_gpiolib_to_irq - convert gpio pin to irq number + * @chip: The gpio chip that the pin belongs to. + * @offset: The offset of the pin in the chip. + * + * This helper returns the irq number calculated from the chip->irq_base and + * the provided offset. + */ +extern int samsung_gpiolib_to_irq(struct gpio_chip *chip, unsigned int offset); + +/* exported for core SoC support to change */ +extern struct samsung_gpio_cfg s3c24xx_gpiocfg_default; + +#ifdef CONFIG_S3C_GPIO_TRACK +extern struct samsung_gpio_chip *s3c_gpios[S3C_GPIO_END]; + +static inline struct samsung_gpio_chip *samsung_gpiolib_getchip(unsigned int chip) +{ + return (chip < S3C_GPIO_END) ? s3c_gpios[chip] : NULL; +} +#else +/* machine specific code should provide samsung_gpiolib_getchip */ + +extern struct samsung_gpio_chip s3c24xx_gpios[]; + +static inline struct samsung_gpio_chip *samsung_gpiolib_getchip(unsigned int pin) +{ + struct samsung_gpio_chip *chip; + + if (pin > S3C_GPIO_END) + return NULL; + + chip = &s3c24xx_gpios[pin/32]; + return ((pin - chip->chip.base) < chip->chip.ngpio) ? chip : NULL; +} + +static inline void s3c_gpiolib_track(struct samsung_gpio_chip *chip) { } +#endif + +#ifdef CONFIG_PM +extern struct samsung_gpio_pm samsung_gpio_pm_1bit; +extern struct samsung_gpio_pm samsung_gpio_pm_2bit; +extern struct samsung_gpio_pm samsung_gpio_pm_4bit; +#define __gpio_pm(x) x +#else +#define samsung_gpio_pm_1bit NULL +#define samsung_gpio_pm_2bit NULL +#define samsung_gpio_pm_4bit NULL +#define __gpio_pm(x) NULL + +#endif /* CONFIG_PM */ + +/* locking wrappers to deal with multiple access to the same gpio bank */ +#define samsung_gpio_lock(_oc, _fl) spin_lock_irqsave(&(_oc)->lock, _fl) +#define samsung_gpio_unlock(_oc, _fl) spin_unlock_irqrestore(&(_oc)->lock, _fl) + +#endif /* __PLAT_SAMSUNG_GPIO_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/iic-core.h b/arch/arm/plat-samsung/include/plat/iic-core.h new file mode 100644 index 000000000..f182669b8 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/iic-core.h @@ -0,0 +1,42 @@ +/* arch/arm/mach-s3c2410/include/mach/iic-core.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * Ben Dooks + * + * S3C - I2C Controller core functions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_ARCH_IIC_CORE_H +#define __ASM_ARCH_IIC_CORE_H __FILE__ + +/* These functions are only for use with the core support code, such as + * the cpu specific initialisation code + */ + +/* re-define device name depending on support. */ +static inline void s3c_i2c0_setname(char *name) +{ + /* currently this device is always compiled in */ + s3c_device_i2c0.name = name; +} + +static inline void s3c_i2c1_setname(char *name) +{ +#ifdef CONFIG_S3C_DEV_I2C1 + s3c_device_i2c1.name = name; +#endif +} + +static inline void s3c_i2c2_setname(char *name) +{ +#ifdef CONFIG_S3C_DEV_I2C2 + s3c_device_i2c2.name = name; +#endif +} + +#endif /* __ASM_ARCH_IIC_H */ diff --git a/arch/arm/plat-samsung/include/plat/irq-uart.h b/arch/arm/plat-samsung/include/plat/irq-uart.h new file mode 100644 index 000000000..a9331e49b --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/irq-uart.h @@ -0,0 +1,20 @@ +/* arch/arm/plat-samsung/include/plat/irq-uart.h + * + * Copyright (c) 2010 Simtec Electronics + * Ben Dooks + * + * Header file for Samsung SoC UART IRQ demux for S3C64XX and later + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +struct s3c_uart_irq { + void __iomem *regs; + unsigned int base_irq; + unsigned int parent_irq; +}; + +extern void s3c_init_uart_irqs(struct s3c_uart_irq *irq, unsigned int nr_irqs); + diff --git a/arch/arm/plat-samsung/include/plat/keypad-core.h b/arch/arm/plat-samsung/include/plat/keypad-core.h new file mode 100644 index 000000000..d513e1b3a --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/keypad-core.h @@ -0,0 +1,31 @@ +/* + * linux/arch/arm/plat-samsung/include/plat/keypad-core.h + * + * Copyright (C) 2010 Samsung Electronics Co.Ltd + * Author: Joonyoung Shim + * + * Samsung keypad controller core function + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#ifndef __ASM_ARCH_KEYPAD_CORE_H +#define __ASM_ARCH_KEYPAD_CORE_H + +/* These function are only for use with the core support code, such as + * the cpu specific initialisation code + */ + +/* re-define device name depending on support. */ +static inline void samsung_keypad_setname(char *name) +{ +#ifdef CONFIG_SAMSUNG_DEV_KEYPAD + samsung_device_keypad.name = name; +#endif +} + +#endif /* __ASM_ARCH_KEYPAD_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/keypad.h b/arch/arm/plat-samsung/include/plat/keypad.h new file mode 100644 index 000000000..c81ace332 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/keypad.h @@ -0,0 +1,31 @@ +/* + * Samsung Platform - Keypad platform data definitions + * + * Copyright (C) 2010 Samsung Electronics Co.Ltd + * Author: Joonyoung Shim + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef __PLAT_SAMSUNG_KEYPAD_H +#define __PLAT_SAMSUNG_KEYPAD_H + +#include + +/** + * samsung_keypad_set_platdata - Set platform data for Samsung Keypad device. + * @pd: Platform data to register to device. + * + * Register the given platform data for use with Samsung Keypad device. + * The call will copy the platform data, so the board definitions can + * make the structure itself __initdata. + */ +extern void samsung_keypad_set_platdata(struct samsung_keypad_platdata *pd); + +/* defined by architecture to configure gpio. */ +extern void samsung_keypad_cfg_gpio(unsigned int rows, unsigned int cols); + +#endif /* __PLAT_SAMSUNG_KEYPAD_H */ diff --git a/arch/arm/plat-samsung/include/plat/map-base.h b/arch/arm/plat-samsung/include/plat/map-base.h new file mode 100644 index 000000000..3ffac4d2e --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/map-base.h @@ -0,0 +1,46 @@ +/* linux/include/asm-arm/plat-s3c/map.h + * + * Copyright 2003, 2007 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C - Memory map definitions (virtual addresses) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_PLAT_MAP_H +#define __ASM_PLAT_MAP_H __FILE__ + +/* Fit all our registers in at 0xF6000000 upwards, trying to use as + * little of the VA space as possible so vmalloc and friends have a + * better chance of getting memory. + * + * we try to ensure stuff like the IRQ registers are available for + * an single MOVS instruction (ie, only 8 bits of set data) + */ + +#define S3C_ADDR_BASE 0xF6000000 + +#ifndef __ASSEMBLY__ +#define S3C_ADDR(x) ((void __iomem __force *)S3C_ADDR_BASE + (x)) +#else +#define S3C_ADDR(x) (S3C_ADDR_BASE + (x)) +#endif + +#define S3C_VA_IRQ S3C_ADDR(0x00000000) /* irq controller(s) */ +#define S3C_VA_SYS S3C_ADDR(0x00100000) /* system control */ +#define S3C_VA_MEM S3C_ADDR(0x00200000) /* memory control */ +#define S3C_VA_TIMER S3C_ADDR(0x00300000) /* timer block */ +#define S3C_VA_WATCHDOG S3C_ADDR(0x00400000) /* watchdog */ +#define S3C_VA_UART S3C_ADDR(0x01000000) /* UART */ + +/* This is used for the CPU specific mappings that may be needed, so that + * they do not need to directly used S3C_ADDR() and thus make it easier to + * modify the space for mapping. + */ +#define S3C_ADDR_CPU(x) S3C_ADDR(0x00500000 + (x)) + +#endif /* __ASM_PLAT_MAP_H */ diff --git a/arch/arm/plat-samsung/include/plat/map-s3c.h b/arch/arm/plat-samsung/include/plat/map-s3c.h new file mode 100644 index 000000000..c0c70a895 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/map-s3c.h @@ -0,0 +1,84 @@ +/* linux/arch/arm/plat-samsung/include/plat/map-s3c.h + * + * Copyright (c) 2008 Simtec Electronics + * Ben Dooks + * + * S3C24XX - Memory map definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_PLAT_MAP_S3C_H +#define __ASM_PLAT_MAP_S3C_H __FILE__ + +#define S3C24XX_VA_IRQ S3C_VA_IRQ +#define S3C24XX_VA_MEMCTRL S3C_VA_MEM +#define S3C24XX_VA_UART S3C_VA_UART + +#define S3C24XX_VA_TIMER S3C_VA_TIMER +#define S3C24XX_VA_CLKPWR S3C_VA_SYS +#define S3C24XX_VA_WATCHDOG S3C_VA_WATCHDOG + +#define S3C2412_VA_SSMC S3C_ADDR_CPU(0x00000000) +#define S3C2412_VA_EBI S3C_ADDR_CPU(0x00100000) + +#define S3C2410_PA_UART (0x50000000) +#define S3C24XX_PA_UART S3C2410_PA_UART + +#ifndef S3C_UART_OFFSET +#define S3C_UART_OFFSET (0x400) +#endif + +/* + * GPIO ports + * + * the calculation for the VA of this must ensure that + * it is the same distance apart from the UART in the + * phsyical address space, as the initial mapping for the IO + * is done as a 1:1 mapping. This puts it (currently) at + * 0xFA800000, which is not in the way of any current mapping + * by the base system. +*/ + +#define S3C2410_PA_GPIO (0x56000000) +#define S3C24XX_PA_GPIO S3C2410_PA_GPIO + +#define S3C24XX_VA_GPIO ((S3C24XX_PA_GPIO - S3C24XX_PA_UART) + S3C24XX_VA_UART) +#define S3C64XX_VA_GPIO S3C_ADDR_CPU(0x00000000) + +#define S3C64XX_VA_MODEM S3C_ADDR_CPU(0x00100000) +#define S3C64XX_VA_USB_HSPHY S3C_ADDR_CPU(0x00200000) + +#define S3C_VA_USB_HSPHY S3C64XX_VA_USB_HSPHY + +/* + * ISA style IO, for each machine to sort out mappings for, + * if it implements it. We reserve two 16M regions for ISA. + */ + +#define S3C2410_ADDR(x) S3C_ADDR(x) + +#define S3C24XX_VA_ISA_WORD S3C2410_ADDR(0x02000000) +#define S3C24XX_VA_ISA_BYTE S3C2410_ADDR(0x03000000) + +/* deal with the registers that move under the 2412/2413 */ + +#if defined(CONFIG_CPU_S3C2412) || defined(CONFIG_CPU_S3C2413) +#ifndef __ASSEMBLY__ +extern void __iomem *s3c24xx_va_gpio2; +#endif +#ifdef CONFIG_CPU_S3C2412_ONLY +#define S3C24XX_VA_GPIO2 (S3C24XX_VA_GPIO + 0x10) +#else +#define S3C24XX_VA_GPIO2 s3c24xx_va_gpio2 +#endif +#else +#define s3c24xx_va_gpio2 S3C24XX_VA_GPIO +#define S3C24XX_VA_GPIO2 S3C24XX_VA_GPIO +#endif + +#include + +#endif /* __ASM_PLAT_MAP_S3C_H */ diff --git a/arch/arm/plat-samsung/include/plat/map-s5p.h b/arch/arm/plat-samsung/include/plat/map-s5p.h new file mode 100644 index 000000000..f5cf2bd20 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/map-s5p.h @@ -0,0 +1,40 @@ +/* linux/arch/arm/plat-samsung/include/plat/map-s5p.h + * + * Copyright (c) 2010 Samsung Electronics Co., Ltd. + * http://www.samsung.com/ + * + * S5P - Memory map definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_PLAT_MAP_S5P_H +#define __ASM_PLAT_MAP_S5P_H __FILE__ + +#define S5P_VA_CHIPID S3C_ADDR(0x02000000) +#define S5P_VA_CMU S3C_ADDR(0x02100000) + +#define S5P_VA_DMC0 S3C_ADDR(0x02440000) +#define S5P_VA_DMC1 S3C_ADDR(0x02480000) +#define S5P_VA_SROMC S3C_ADDR(0x024C0000) + +#define S5P_VA_COREPERI_BASE S3C_ADDR(0x02800000) +#define S5P_VA_COREPERI(x) (S5P_VA_COREPERI_BASE + (x)) +#define S5P_VA_SCU S5P_VA_COREPERI(0x0) +#define S5P_VA_TWD S5P_VA_COREPERI(0x600) + +#define VA_VIC(x) (S3C_VA_IRQ + ((x) * 0x10000)) +#define VA_VIC0 VA_VIC(0) +#define VA_VIC1 VA_VIC(1) +#define VA_VIC2 VA_VIC(2) +#define VA_VIC3 VA_VIC(3) + +#ifndef S3C_UART_OFFSET +#define S3C_UART_OFFSET (0x400) +#endif + +#include + +#endif /* __ASM_PLAT_MAP_S5P_H */ diff --git a/arch/arm/plat-samsung/include/plat/nand-core.h b/arch/arm/plat-samsung/include/plat/nand-core.h new file mode 100644 index 000000000..6de20789a --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/nand-core.h @@ -0,0 +1,28 @@ +/* arch/arm/plat-samsung/include/plat/nand-core.h + * + * Copyright (c) 2010 Samsung Electronics Co., Ltd. + * http://www.samsung.com/ + * + * S3C - Nand Controller core functions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_ARCH_NAND_CORE_H +#define __ASM_ARCH_NAND_CORE_H __FILE__ + +/* These functions are only for use with the core support code, such as + * the cpu specific initialisation code + */ + +/* re-define device name depending on support. */ +static inline void s3c_nand_setname(char *name) +{ +#ifdef CONFIG_S3C_DEV_NAND + s3c_device_nand.name = name; +#endif +} + +#endif /* __ASM_ARCH_NAND_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/onenand-core.h b/arch/arm/plat-samsung/include/plat/onenand-core.h new file mode 100644 index 000000000..7701cb702 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/onenand-core.h @@ -0,0 +1,37 @@ +/* + * linux/arch/arm/plat-samsung/onenand-core.h + * + * Copyright (c) 2010 Samsung Electronics + * Kyungmin Park + * Marek Szyprowski + * + * Samsung OneNAD Controller core functions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_ARCH_ONENAND_CORE_H +#define __ASM_ARCH_ONENAND_CORE_H __FILE__ + +/* These functions are only for use with the core support code, such as + * the cpu specific initialisation code + */ + +/* re-define device name depending on support. */ +static inline void s3c_onenand_setname(char *name) +{ +#ifdef CONFIG_S3C_DEV_ONENAND + s3c_device_onenand.name = name; +#endif +} + +static inline void s3c64xx_onenand1_setname(char *name) +{ +#ifdef CONFIG_S3C64XX_DEV_ONENAND1 + s3c64xx_device_onenand1.name = name; +#endif +} + +#endif /* __ASM_ARCH_ONENAND_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/pm-common.h b/arch/arm/plat-samsung/include/plat/pm-common.h new file mode 100644 index 000000000..8705f9e0e --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/pm-common.h @@ -0,0 +1,110 @@ +/* + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * Tomasz Figa + * Copyright (c) 2004 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Written by Ben Dooks, + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_SAMSUNG_PM_COMMON_H +#define __PLAT_SAMSUNG_PM_COMMON_H __FILE__ + +#include + +/* sleep save info */ + +/** + * struct sleep_save - save information for shared peripherals. + * @reg: Pointer to the register to save. + * @val: Holder for the value saved from reg. + * + * This describes a list of registers which is used by the pm core and + * other subsystem to save and restore register values over suspend. + */ +struct sleep_save { + void __iomem *reg; + unsigned long val; +}; + +#define SAVE_ITEM(x) \ + { .reg = (x) } + +/* helper functions to save/restore lists of registers. */ + +extern void s3c_pm_do_save(struct sleep_save *ptr, int count); +extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count); +extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count); + +/* PM debug functions */ + +/** + * struct pm_uart_save - save block for core UART + * @ulcon: Save value for S3C2410_ULCON + * @ucon: Save value for S3C2410_UCON + * @ufcon: Save value for S3C2410_UFCON + * @umcon: Save value for S3C2410_UMCON + * @ubrdiv: Save value for S3C2410_UBRDIV + * + * Save block for UART registers to be held over sleep and restored if they + * are needed (say by debug). +*/ +struct pm_uart_save { + u32 ulcon; + u32 ucon; + u32 ufcon; + u32 umcon; + u32 ubrdiv; + u32 udivslot; +}; + +#ifdef CONFIG_SAMSUNG_PM_DEBUG +/** + * s3c_pm_dbg() - low level debug function for use in suspend/resume. + * @msg: The message to print. + * + * This function is used mainly to debug the resume process before the system + * can rely on printk/console output. It uses the low-level debugging output + * routine printascii() to do its work. + */ +extern void s3c_pm_dbg(const char *msg, ...); + +/** + * s3c_pm_debug_init() - suspend/resume low level debug initialization. + * @base: Virtual base of UART to use for suspend/resume debugging. + * + * This function needs to be called before S3C_PMDBG() can be used, to set up + * UART port base address and configuration. + */ +extern void s3c_pm_debug_init(void); + +#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt) + +extern void s3c_pm_save_uarts(void); +extern void s3c_pm_restore_uarts(void); +#else +#define S3C_PMDBG(fmt...) pr_debug(fmt) +#define s3c_pm_debug_init() do { } while (0) + +static inline void s3c_pm_save_uarts(void) { } +static inline void s3c_pm_restore_uarts(void) { } +#endif + +/* suspend memory checking */ + +#ifdef CONFIG_SAMSUNG_PM_CHECK +extern void s3c_pm_check_prepare(void); +extern void s3c_pm_check_restore(void); +extern void s3c_pm_check_cleanup(void); +extern void s3c_pm_check_store(void); +#else +#define s3c_pm_check_prepare() do { } while (0) +#define s3c_pm_check_restore() do { } while (0) +#define s3c_pm_check_cleanup() do { } while (0) +#define s3c_pm_check_store() do { } while (0) +#endif + +#endif diff --git a/arch/arm/plat-samsung/include/plat/pm.h b/arch/arm/plat-samsung/include/plat/pm.h new file mode 100644 index 000000000..7f415ce74 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/pm.h @@ -0,0 +1,121 @@ +/* arch/arm/plat-samsung/include/plat/pm.h + * + * Copyright (c) 2004 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Written by Ben Dooks, + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* s3c_pm_init + * + * called from board at initialisation time to setup the power + * management +*/ + +#include + +struct device; + +#ifdef CONFIG_SAMSUNG_PM + +extern __init int s3c_pm_init(void); +extern __init int s3c64xx_pm_init(void); + +#else + +static inline int s3c_pm_init(void) +{ + return 0; +} + +static inline int s3c64xx_pm_init(void) +{ + return 0; +} +#endif + +/* configuration for the IRQ mask over sleep */ +extern unsigned long s3c_irqwake_intmask; +extern unsigned long s3c_irqwake_eintmask; + +/* IRQ masks for IRQs allowed to go to sleep (see irq.c) */ +extern unsigned long s3c_irqwake_intallow; +#ifdef CONFIG_PM_SLEEP +extern unsigned long s3c_irqwake_eintallow; +#else +#define s3c_irqwake_eintallow 0 +#endif + +/* per-cpu sleep functions */ + +extern void (*pm_cpu_prep)(void); +extern int (*pm_cpu_sleep)(unsigned long); + +/* Flags for PM Control */ + +extern unsigned long s3c_pm_flags; + +/* from sleep.S */ + +extern int s3c2410_cpu_suspend(unsigned long); + +#ifdef CONFIG_PM_SLEEP +extern int s3c_irq_wake(struct irq_data *data, unsigned int state); +extern void s3c_cpu_resume(void); +#else +#define s3c_irq_wake NULL +#define s3c_cpu_resume NULL +#endif + +#ifdef CONFIG_SAMSUNG_PM +extern int s3c_irqext_wake(struct irq_data *data, unsigned int state); +#else +#define s3c_irqext_wake NULL +#endif + +#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK +/** + * s3c_pm_debug_smdkled() - Debug PM suspend/resume via SMDK Board LEDs + * @set: set bits for the state of the LEDs + * @clear: clear bits for the state of the LEDs. + */ +extern void s3c_pm_debug_smdkled(u32 set, u32 clear); + +#else +static inline void s3c_pm_debug_smdkled(u32 set, u32 clear) { } +#endif /* CONFIG_S3C_PM_DEBUG_LED_SMDK */ + +/** + * s3c_pm_configure_extint() - ensure pins are correctly set for IRQ + * + * Setup all the necessary GPIO pins for waking the system on external + * interrupt. + */ +extern void s3c_pm_configure_extint(void); + +#ifdef CONFIG_GPIO_SAMSUNG +/** + * samsung_pm_restore_gpios() - restore the state of the gpios after sleep. + * + * Restore the state of the GPIO pins after sleep, which may involve ensuring + * that we do not glitch the state of the pins from that the bootloader's + * resume code has done. +*/ +extern void samsung_pm_restore_gpios(void); + +/** + * samsung_pm_save_gpios() - save the state of the GPIOs for restoring after sleep. + * + * Save the GPIO states for resotration on resume. See samsung_pm_restore_gpios(). + */ +extern void samsung_pm_save_gpios(void); +#else +static inline void samsung_pm_restore_gpios(void) {} +static inline void samsung_pm_save_gpios(void) {} +#endif + +extern void s3c_pm_save_core(void); +extern void s3c_pm_restore_core(void); diff --git a/arch/arm/plat-samsung/include/plat/pwm-core.h b/arch/arm/plat-samsung/include/plat/pwm-core.h new file mode 100644 index 000000000..5bff1facb --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/pwm-core.h @@ -0,0 +1,22 @@ +/* + * Copyright 2013 Tomasz Figa + * + * Samsung PWM controller platform data helpers. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_PWM_CORE_H +#define __ASM_ARCH_PWM_CORE_H __FILE__ + +#include + +#ifdef CONFIG_SAMSUNG_DEV_PWM +extern void samsung_pwm_set_platdata(struct samsung_pwm_variant *pd); +#else +static inline void samsung_pwm_set_platdata(struct samsung_pwm_variant *pd) { } +#endif + +#endif /* __ASM_ARCH_PWM_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/regs-adc.h b/arch/arm/plat-samsung/include/plat/regs-adc.h new file mode 100644 index 000000000..706121001 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/regs-adc.h @@ -0,0 +1,68 @@ +/* arch/arm/mach-s3c2410/include/mach/regs-adc.h + * + * Copyright (c) 2004 Shannon Holland + * + * This program is free software; yosu can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * S3C2410 ADC registers +*/ + +#ifndef __ASM_ARCH_REGS_ADC_H +#define __ASM_ARCH_REGS_ADC_H "regs-adc.h" + +#define S3C2410_ADCREG(x) (x) + +#define S3C2410_ADCCON S3C2410_ADCREG(0x00) +#define S3C2410_ADCTSC S3C2410_ADCREG(0x04) +#define S3C2410_ADCDLY S3C2410_ADCREG(0x08) +#define S3C2410_ADCDAT0 S3C2410_ADCREG(0x0C) +#define S3C2410_ADCDAT1 S3C2410_ADCREG(0x10) +#define S3C64XX_ADCUPDN S3C2410_ADCREG(0x14) +#define S3C2443_ADCMUX S3C2410_ADCREG(0x18) +#define S3C64XX_ADCCLRINT S3C2410_ADCREG(0x18) +#define S5P_ADCMUX S3C2410_ADCREG(0x1C) +#define S3C64XX_ADCCLRINTPNDNUP S3C2410_ADCREG(0x20) + + +/* ADCCON Register Bits */ +#define S3C64XX_ADCCON_RESSEL (1<<16) +#define S3C2410_ADCCON_ECFLG (1<<15) +#define S3C2410_ADCCON_PRSCEN (1<<14) +#define S3C2410_ADCCON_PRSCVL(x) (((x)&0xFF)<<6) +#define S3C2410_ADCCON_PRSCVLMASK (0xFF<<6) +#define S3C2410_ADCCON_SELMUX(x) (((x)&0x7)<<3) +#define S3C2410_ADCCON_MUXMASK (0x7<<3) +#define S3C2416_ADCCON_RESSEL (1 << 3) +#define S3C2410_ADCCON_STDBM (1<<2) +#define S3C2410_ADCCON_READ_START (1<<1) +#define S3C2410_ADCCON_ENABLE_START (1<<0) +#define S3C2410_ADCCON_STARTMASK (0x3<<0) + + +/* ADCTSC Register Bits */ +#define S3C2443_ADCTSC_UD_SEN (1 << 8) +#define S3C2410_ADCTSC_YM_SEN (1<<7) +#define S3C2410_ADCTSC_YP_SEN (1<<6) +#define S3C2410_ADCTSC_XM_SEN (1<<5) +#define S3C2410_ADCTSC_XP_SEN (1<<4) +#define S3C2410_ADCTSC_PULL_UP_DISABLE (1<<3) +#define S3C2410_ADCTSC_AUTO_PST (1<<2) +#define S3C2410_ADCTSC_XY_PST(x) (((x)&0x3)<<0) + +/* ADCDAT0 Bits */ +#define S3C2410_ADCDAT0_UPDOWN (1<<15) +#define S3C2410_ADCDAT0_AUTO_PST (1<<14) +#define S3C2410_ADCDAT0_XY_PST (0x3<<12) +#define S3C2410_ADCDAT0_XPDATA_MASK (0x03FF) + +/* ADCDAT1 Bits */ +#define S3C2410_ADCDAT1_UPDOWN (1<<15) +#define S3C2410_ADCDAT1_AUTO_PST (1<<14) +#define S3C2410_ADCDAT1_XY_PST (0x3<<12) +#define S3C2410_ADCDAT1_YPDATA_MASK (0x03FF) + +#endif /* __ASM_ARCH_REGS_ADC_H */ + + diff --git a/arch/arm/plat-samsung/include/plat/regs-irqtype.h b/arch/arm/plat-samsung/include/plat/regs-irqtype.h new file mode 100644 index 000000000..c63cd3fc5 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/regs-irqtype.h @@ -0,0 +1,21 @@ +/* arch/arm/plat-s3c/include/plat/regs-irqtype.h + * + * Copyright 2008 Simtec Electronics + * Ben Dooks + * http://armlinux.simtec.co.uk/ + * + * S3C - IRQ detection types. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* values for S3C2410_EXTINT0/1/2 and other cpus in the series, including + * the S3C64XX +*/ +#define S3C2410_EXTINT_LOWLEV (0x00) +#define S3C2410_EXTINT_HILEV (0x01) +#define S3C2410_EXTINT_FALLEDGE (0x02) +#define S3C2410_EXTINT_RISEEDGE (0x04) +#define S3C2410_EXTINT_BOTHEDGE (0x06) diff --git a/arch/arm/plat-samsung/include/plat/regs-spi.h b/arch/arm/plat-samsung/include/plat/regs-spi.h new file mode 100644 index 000000000..552fe7cfe --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/regs-spi.h @@ -0,0 +1,48 @@ +/* arch/arm/plat-samsung/include/plat/regs-spi.h + * + * Copyright (c) 2004 Fetron GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * S3C2410 SPI register definition +*/ + +#ifndef __ASM_ARCH_REGS_SPI_H +#define __ASM_ARCH_REGS_SPI_H + +#define S3C2410_SPI1 (0x20) +#define S3C2412_SPI1 (0x100) + +#define S3C2410_SPCON (0x00) + +#define S3C2410_SPCON_SMOD_DMA (2 << 5) /* DMA mode */ +#define S3C2410_SPCON_SMOD_INT (1 << 5) /* interrupt mode */ +#define S3C2410_SPCON_SMOD_POLL (0 << 5) /* polling mode */ +#define S3C2410_SPCON_ENSCK (1 << 4) /* Enable SCK */ +#define S3C2410_SPCON_MSTR (1 << 3) /* Master:1, Slave:0 select */ +#define S3C2410_SPCON_CPOL_HIGH (1 << 2) /* Clock polarity select */ +#define S3C2410_SPCON_CPOL_LOW (0 << 2) /* Clock polarity select */ + +#define S3C2410_SPCON_CPHA_FMTB (1 << 1) /* Clock Phase Select */ +#define S3C2410_SPCON_CPHA_FMTA (0 << 1) /* Clock Phase Select */ + +#define S3C2410_SPSTA (0x04) + +#define S3C2410_SPSTA_DCOL (1 << 2) /* Data Collision Error */ +#define S3C2410_SPSTA_MULD (1 << 1) /* Multi Master Error */ +#define S3C2410_SPSTA_READY (1 << 0) /* Data Tx/Rx ready */ +#define S3C2412_SPSTA_READY_ORG (1 << 3) + +#define S3C2410_SPPIN (0x08) + +#define S3C2410_SPPIN_ENMUL (1 << 2) /* Multi Master Error detect */ +#define S3C2410_SPPIN_RESERVED (1 << 1) +#define S3C2410_SPPIN_KEEP (1 << 0) /* Master Out keep */ + +#define S3C2410_SPPRE (0x0C) +#define S3C2410_SPTDAT (0x10) +#define S3C2410_SPRDAT (0x14) + +#endif /* __ASM_ARCH_REGS_SPI_H */ diff --git a/arch/arm/plat-samsung/include/plat/regs-srom.h b/arch/arm/plat-samsung/include/plat/regs-srom.h new file mode 100644 index 000000000..9b6729c81 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/regs-srom.h @@ -0,0 +1,54 @@ +/* linux/arch/arm/plat-samsung/include/plat/regs-srom.h + * + * Copyright (c) 2010 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * S5P SROMC register definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_SAMSUNG_REGS_SROM_H +#define __PLAT_SAMSUNG_REGS_SROM_H __FILE__ + +#include + +#define S5P_SROMREG(x) (S5P_VA_SROMC + (x)) + +#define S5P_SROM_BW S5P_SROMREG(0x0) +#define S5P_SROM_BC0 S5P_SROMREG(0x4) +#define S5P_SROM_BC1 S5P_SROMREG(0x8) +#define S5P_SROM_BC2 S5P_SROMREG(0xc) +#define S5P_SROM_BC3 S5P_SROMREG(0x10) +#define S5P_SROM_BC4 S5P_SROMREG(0x14) +#define S5P_SROM_BC5 S5P_SROMREG(0x18) + +/* one register BW holds 4 x 4-bit packed settings for NCS0 - NCS3 */ + +#define S5P_SROM_BW__DATAWIDTH__SHIFT 0 +#define S5P_SROM_BW__ADDRMODE__SHIFT 1 +#define S5P_SROM_BW__WAITENABLE__SHIFT 2 +#define S5P_SROM_BW__BYTEENABLE__SHIFT 3 + +#define S5P_SROM_BW__CS_MASK 0xf + +#define S5P_SROM_BW__NCS0__SHIFT 0 +#define S5P_SROM_BW__NCS1__SHIFT 4 +#define S5P_SROM_BW__NCS2__SHIFT 8 +#define S5P_SROM_BW__NCS3__SHIFT 12 +#define S5P_SROM_BW__NCS4__SHIFT 16 +#define S5P_SROM_BW__NCS5__SHIFT 20 + +/* applies to same to BCS0 - BCS3 */ + +#define S5P_SROM_BCX__PMC__SHIFT 0 +#define S5P_SROM_BCX__TACP__SHIFT 4 +#define S5P_SROM_BCX__TCAH__SHIFT 8 +#define S5P_SROM_BCX__TCOH__SHIFT 12 +#define S5P_SROM_BCX__TACC__SHIFT 16 +#define S5P_SROM_BCX__TCOS__SHIFT 24 +#define S5P_SROM_BCX__TACS__SHIFT 28 + +#endif /* __PLAT_SAMSUNG_REGS_SROM_H */ diff --git a/arch/arm/plat-samsung/include/plat/regs-udc.h b/arch/arm/plat-samsung/include/plat/regs-udc.h new file mode 100644 index 000000000..4003d3dab --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/regs-udc.h @@ -0,0 +1,151 @@ +/* arch/arm/plat-samsung/include/plat/regs-udc.h + * + * Copyright (C) 2004 Herbert Poetzl + * + * This include file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. +*/ + +#ifndef __ASM_ARCH_REGS_UDC_H +#define __ASM_ARCH_REGS_UDC_H + +#define S3C2410_USBDREG(x) (x) + +#define S3C2410_UDC_FUNC_ADDR_REG S3C2410_USBDREG(0x0140) +#define S3C2410_UDC_PWR_REG S3C2410_USBDREG(0x0144) +#define S3C2410_UDC_EP_INT_REG S3C2410_USBDREG(0x0148) + +#define S3C2410_UDC_USB_INT_REG S3C2410_USBDREG(0x0158) +#define S3C2410_UDC_EP_INT_EN_REG S3C2410_USBDREG(0x015c) + +#define S3C2410_UDC_USB_INT_EN_REG S3C2410_USBDREG(0x016c) + +#define S3C2410_UDC_FRAME_NUM1_REG S3C2410_USBDREG(0x0170) +#define S3C2410_UDC_FRAME_NUM2_REG S3C2410_USBDREG(0x0174) + +#define S3C2410_UDC_EP0_FIFO_REG S3C2410_USBDREG(0x01c0) +#define S3C2410_UDC_EP1_FIFO_REG S3C2410_USBDREG(0x01c4) +#define S3C2410_UDC_EP2_FIFO_REG S3C2410_USBDREG(0x01c8) +#define S3C2410_UDC_EP3_FIFO_REG S3C2410_USBDREG(0x01cc) +#define S3C2410_UDC_EP4_FIFO_REG S3C2410_USBDREG(0x01d0) + +#define S3C2410_UDC_EP1_DMA_CON S3C2410_USBDREG(0x0200) +#define S3C2410_UDC_EP1_DMA_UNIT S3C2410_USBDREG(0x0204) +#define S3C2410_UDC_EP1_DMA_FIFO S3C2410_USBDREG(0x0208) +#define S3C2410_UDC_EP1_DMA_TTC_L S3C2410_USBDREG(0x020c) +#define S3C2410_UDC_EP1_DMA_TTC_M S3C2410_USBDREG(0x0210) +#define S3C2410_UDC_EP1_DMA_TTC_H S3C2410_USBDREG(0x0214) + +#define S3C2410_UDC_EP2_DMA_CON S3C2410_USBDREG(0x0218) +#define S3C2410_UDC_EP2_DMA_UNIT S3C2410_USBDREG(0x021c) +#define S3C2410_UDC_EP2_DMA_FIFO S3C2410_USBDREG(0x0220) +#define S3C2410_UDC_EP2_DMA_TTC_L S3C2410_USBDREG(0x0224) +#define S3C2410_UDC_EP2_DMA_TTC_M S3C2410_USBDREG(0x0228) +#define S3C2410_UDC_EP2_DMA_TTC_H S3C2410_USBDREG(0x022c) + +#define S3C2410_UDC_EP3_DMA_CON S3C2410_USBDREG(0x0240) +#define S3C2410_UDC_EP3_DMA_UNIT S3C2410_USBDREG(0x0244) +#define S3C2410_UDC_EP3_DMA_FIFO S3C2410_USBDREG(0x0248) +#define S3C2410_UDC_EP3_DMA_TTC_L S3C2410_USBDREG(0x024c) +#define S3C2410_UDC_EP3_DMA_TTC_M S3C2410_USBDREG(0x0250) +#define S3C2410_UDC_EP3_DMA_TTC_H S3C2410_USBDREG(0x0254) + +#define S3C2410_UDC_EP4_DMA_CON S3C2410_USBDREG(0x0258) +#define S3C2410_UDC_EP4_DMA_UNIT S3C2410_USBDREG(0x025c) +#define S3C2410_UDC_EP4_DMA_FIFO S3C2410_USBDREG(0x0260) +#define S3C2410_UDC_EP4_DMA_TTC_L S3C2410_USBDREG(0x0264) +#define S3C2410_UDC_EP4_DMA_TTC_M S3C2410_USBDREG(0x0268) +#define S3C2410_UDC_EP4_DMA_TTC_H S3C2410_USBDREG(0x026c) + +#define S3C2410_UDC_INDEX_REG S3C2410_USBDREG(0x0178) + +/* indexed registers */ + +#define S3C2410_UDC_MAXP_REG S3C2410_USBDREG(0x0180) + +#define S3C2410_UDC_EP0_CSR_REG S3C2410_USBDREG(0x0184) + +#define S3C2410_UDC_IN_CSR1_REG S3C2410_USBDREG(0x0184) +#define S3C2410_UDC_IN_CSR2_REG S3C2410_USBDREG(0x0188) + +#define S3C2410_UDC_OUT_CSR1_REG S3C2410_USBDREG(0x0190) +#define S3C2410_UDC_OUT_CSR2_REG S3C2410_USBDREG(0x0194) +#define S3C2410_UDC_OUT_FIFO_CNT1_REG S3C2410_USBDREG(0x0198) +#define S3C2410_UDC_OUT_FIFO_CNT2_REG S3C2410_USBDREG(0x019c) + +#define S3C2410_UDC_FUNCADDR_UPDATE (1 << 7) + +#define S3C2410_UDC_PWR_ISOUP (1 << 7) /* R/W */ +#define S3C2410_UDC_PWR_RESET (1 << 3) /* R */ +#define S3C2410_UDC_PWR_RESUME (1 << 2) /* R/W */ +#define S3C2410_UDC_PWR_SUSPEND (1 << 1) /* R */ +#define S3C2410_UDC_PWR_ENSUSPEND (1 << 0) /* R/W */ + +#define S3C2410_UDC_PWR_DEFAULT (0x00) + +#define S3C2410_UDC_INT_EP4 (1 << 4) /* R/W (clear only) */ +#define S3C2410_UDC_INT_EP3 (1 << 3) /* R/W (clear only) */ +#define S3C2410_UDC_INT_EP2 (1 << 2) /* R/W (clear only) */ +#define S3C2410_UDC_INT_EP1 (1 << 1) /* R/W (clear only) */ +#define S3C2410_UDC_INT_EP0 (1 << 0) /* R/W (clear only) */ + +#define S3C2410_UDC_USBINT_RESET (1 << 2) /* R/W (clear only) */ +#define S3C2410_UDC_USBINT_RESUME (1 << 1) /* R/W (clear only) */ +#define S3C2410_UDC_USBINT_SUSPEND (1 << 0) /* R/W (clear only) */ + +#define S3C2410_UDC_INTE_EP4 (1 << 4) /* R/W */ +#define S3C2410_UDC_INTE_EP3 (1 << 3) /* R/W */ +#define S3C2410_UDC_INTE_EP2 (1 << 2) /* R/W */ +#define S3C2410_UDC_INTE_EP1 (1 << 1) /* R/W */ +#define S3C2410_UDC_INTE_EP0 (1 << 0) /* R/W */ + +#define S3C2410_UDC_USBINTE_RESET (1 << 2) /* R/W */ +#define S3C2410_UDC_USBINTE_SUSPEND (1 << 0) /* R/W */ + +#define S3C2410_UDC_INDEX_EP0 (0x00) +#define S3C2410_UDC_INDEX_EP1 (0x01) +#define S3C2410_UDC_INDEX_EP2 (0x02) +#define S3C2410_UDC_INDEX_EP3 (0x03) +#define S3C2410_UDC_INDEX_EP4 (0x04) + +#define S3C2410_UDC_ICSR1_CLRDT (1 << 6) /* R/W */ +#define S3C2410_UDC_ICSR1_SENTSTL (1 << 5) /* R/W (clear only) */ +#define S3C2410_UDC_ICSR1_SENDSTL (1 << 4) /* R/W */ +#define S3C2410_UDC_ICSR1_FFLUSH (1 << 3) /* W (set only) */ +#define S3C2410_UDC_ICSR1_UNDRUN (1 << 2) /* R/W (clear only) */ +#define S3C2410_UDC_ICSR1_PKTRDY (1 << 0) /* R/W (set only) */ + +#define S3C2410_UDC_ICSR2_AUTOSET (1 << 7) /* R/W */ +#define S3C2410_UDC_ICSR2_ISO (1 << 6) /* R/W */ +#define S3C2410_UDC_ICSR2_MODEIN (1 << 5) /* R/W */ +#define S3C2410_UDC_ICSR2_DMAIEN (1 << 4) /* R/W */ + +#define S3C2410_UDC_OCSR1_CLRDT (1 << 7) /* R/W */ +#define S3C2410_UDC_OCSR1_SENTSTL (1 << 6) /* R/W (clear only) */ +#define S3C2410_UDC_OCSR1_SENDSTL (1 << 5) /* R/W */ +#define S3C2410_UDC_OCSR1_FFLUSH (1 << 4) /* R/W */ +#define S3C2410_UDC_OCSR1_DERROR (1 << 3) /* R */ +#define S3C2410_UDC_OCSR1_OVRRUN (1 << 2) /* R/W (clear only) */ +#define S3C2410_UDC_OCSR1_PKTRDY (1 << 0) /* R/W (clear only) */ + +#define S3C2410_UDC_OCSR2_AUTOCLR (1 << 7) /* R/W */ +#define S3C2410_UDC_OCSR2_ISO (1 << 6) /* R/W */ +#define S3C2410_UDC_OCSR2_DMAIEN (1 << 5) /* R/W */ + +#define S3C2410_UDC_EP0_CSR_OPKRDY (1 << 0) +#define S3C2410_UDC_EP0_CSR_IPKRDY (1 << 1) +#define S3C2410_UDC_EP0_CSR_SENTSTL (1 << 2) +#define S3C2410_UDC_EP0_CSR_DE (1 << 3) +#define S3C2410_UDC_EP0_CSR_SE (1 << 4) +#define S3C2410_UDC_EP0_CSR_SENDSTL (1 << 5) +#define S3C2410_UDC_EP0_CSR_SOPKTRDY (1 << 6) +#define S3C2410_UDC_EP0_CSR_SSE (1 << 7) + +#define S3C2410_UDC_MAXP_8 (1 << 0) +#define S3C2410_UDC_MAXP_16 (1 << 1) +#define S3C2410_UDC_MAXP_32 (1 << 2) +#define S3C2410_UDC_MAXP_64 (1 << 3) + +#endif diff --git a/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h b/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h new file mode 100644 index 000000000..fcf279662 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h @@ -0,0 +1,51 @@ +/* arch/arm/plat-s3c/include/plat/regs-usb-hsotg-phy.h + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C - USB2.0 Highspeed/OtG device PHY registers + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +/* Note, this is a separate header file as some of the clock framework + * needs to touch this if the clk_48m is used as the USB OHCI or other + * peripheral source. +*/ + +#ifndef __PLAT_S3C64XX_REGS_USB_HSOTG_PHY_H +#define __PLAT_S3C64XX_REGS_USB_HSOTG_PHY_H __FILE__ + +/* S3C64XX_PA_USB_HSPHY */ + +#define S3C_HSOTG_PHYREG(x) ((x) + S3C_VA_USB_HSPHY) + +#define S3C_PHYPWR S3C_HSOTG_PHYREG(0x00) +#define S3C_PHYPWR_NORMAL_MASK (0x19 << 0) +#define S3C_PHYPWR_OTG_DISABLE (1 << 4) +#define S3C_PHYPWR_ANALOG_POWERDOWN (1 << 3) +#define SRC_PHYPWR_FORCE_SUSPEND (1 << 1) + +#define S3C_PHYCLK S3C_HSOTG_PHYREG(0x04) +#define S3C_PHYCLK_MODE_USB11 (1 << 6) +#define S3C_PHYCLK_EXT_OSC (1 << 5) +#define S3C_PHYCLK_CLK_FORCE (1 << 4) +#define S3C_PHYCLK_ID_PULL (1 << 2) +#define S3C_PHYCLK_CLKSEL_MASK (0x3 << 0) +#define S3C_PHYCLK_CLKSEL_SHIFT (0) +#define S3C_PHYCLK_CLKSEL_48M (0x0 << 0) +#define S3C_PHYCLK_CLKSEL_12M (0x2 << 0) +#define S3C_PHYCLK_CLKSEL_24M (0x3 << 0) + +#define S3C_RSTCON S3C_HSOTG_PHYREG(0x08) +#define S3C_RSTCON_PHYCLK (1 << 2) +#define S3C_RSTCON_HCLK (1 << 1) +#define S3C_RSTCON_PHY (1 << 0) + +#define S3C_PHYTUNE S3C_HSOTG_PHYREG(0x20) + +#endif /* __PLAT_S3C64XX_REGS_USB_HSOTG_PHY_H */ diff --git a/arch/arm/plat-samsung/include/plat/samsung-time.h b/arch/arm/plat-samsung/include/plat/samsung-time.h new file mode 100644 index 000000000..209464ade --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/samsung-time.h @@ -0,0 +1,30 @@ +/* linux/arch/arm/plat-samsung/include/plat/samsung-time.h + * + * Copyright 2011 Samsung Electronics Co., Ltd. + * http://www.samsung.com/ + * + * Header file for samsung s3c and s5p time support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_PLAT_SAMSUNG_TIME_H +#define __ASM_PLAT_SAMSUNG_TIME_H __FILE__ + +/* SAMSUNG HR-Timer Clock mode */ +enum samsung_timer_mode { + SAMSUNG_PWM0, + SAMSUNG_PWM1, + SAMSUNG_PWM2, + SAMSUNG_PWM3, + SAMSUNG_PWM4, +}; + +extern void __init samsung_set_timer_source(enum samsung_timer_mode event, + enum samsung_timer_mode source); + +extern void __init samsung_timer_init(void); + +#endif /* __ASM_PLAT_SAMSUNG_TIME_H */ diff --git a/arch/arm/plat-samsung/include/plat/sdhci.h b/arch/arm/plat-samsung/include/plat/sdhci.h new file mode 100644 index 000000000..2787553c3 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/sdhci.h @@ -0,0 +1,166 @@ +/* linux/arch/arm/plat-samsung/include/plat/sdhci.h + * + * Copyright (c) 2011 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Copyright 2008 Openmoko, Inc. + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks + * + * S3C Platform - SDHCI (HSMMC) platform data definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_S3C_SDHCI_H +#define __PLAT_S3C_SDHCI_H __FILE__ + +#include +#include + +/* s3c_sdhci_set_platdata() - common helper for setting SDHCI platform data + * @pd: The default platform data for this device. + * @set: Pointer to the platform data to fill in. + */ +extern void s3c_sdhci_set_platdata(struct s3c_sdhci_platdata *pd, + struct s3c_sdhci_platdata *set); + +/** + * s3c_sdhci0_set_platdata - Set platform data for S3C SDHCI device. + * @pd: Platform data to register to device. + * + * Register the given platform data for use withe S3C SDHCI device. + * The call will copy the platform data, so the board definitions can + * make the structure itself __initdata. + */ +extern void s3c_sdhci0_set_platdata(struct s3c_sdhci_platdata *pd); +extern void s3c_sdhci1_set_platdata(struct s3c_sdhci_platdata *pd); +extern void s3c_sdhci2_set_platdata(struct s3c_sdhci_platdata *pd); +extern void s3c_sdhci3_set_platdata(struct s3c_sdhci_platdata *pd); + +/* Default platform data, exported so that per-cpu initialisation can + * set the correct one when there are more than one cpu type selected. +*/ + +extern struct s3c_sdhci_platdata s3c_hsmmc0_def_platdata; +extern struct s3c_sdhci_platdata s3c_hsmmc1_def_platdata; +extern struct s3c_sdhci_platdata s3c_hsmmc2_def_platdata; +extern struct s3c_sdhci_platdata s3c_hsmmc3_def_platdata; + +/* Helper function availability */ + +extern void s3c2416_setup_sdhci0_cfg_gpio(struct platform_device *, int w); +extern void s3c2416_setup_sdhci1_cfg_gpio(struct platform_device *, int w); +extern void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *, int w); +extern void s3c64xx_setup_sdhci1_cfg_gpio(struct platform_device *, int w); +extern void s3c64xx_setup_sdhci2_cfg_gpio(struct platform_device *, int w); + +/* S3C2416 SDHCI setup */ + +#ifdef CONFIG_S3C2416_SETUP_SDHCI +static inline void s3c2416_default_sdhci0(void) +{ +#ifdef CONFIG_S3C_DEV_HSMMC + s3c_hsmmc0_def_platdata.cfg_gpio = s3c2416_setup_sdhci0_cfg_gpio; +#endif /* CONFIG_S3C_DEV_HSMMC */ +} + +static inline void s3c2416_default_sdhci1(void) +{ +#ifdef CONFIG_S3C_DEV_HSMMC1 + s3c_hsmmc1_def_platdata.cfg_gpio = s3c2416_setup_sdhci1_cfg_gpio; +#endif /* CONFIG_S3C_DEV_HSMMC1 */ +} + +#else +static inline void s3c2416_default_sdhci0(void) { } +static inline void s3c2416_default_sdhci1(void) { } + +#endif /* CONFIG_S3C2416_SETUP_SDHCI */ + +/* S3C64XX SDHCI setup */ + +#ifdef CONFIG_S3C64XX_SETUP_SDHCI +static inline void s3c6400_default_sdhci0(void) +{ +#ifdef CONFIG_S3C_DEV_HSMMC + s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio; +#endif +} + +static inline void s3c6400_default_sdhci1(void) +{ +#ifdef CONFIG_S3C_DEV_HSMMC1 + s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio; +#endif +} + +static inline void s3c6400_default_sdhci2(void) +{ +#ifdef CONFIG_S3C_DEV_HSMMC2 + s3c_hsmmc2_def_platdata.cfg_gpio = s3c64xx_setup_sdhci2_cfg_gpio; +#endif +} + +static inline void s3c6410_default_sdhci0(void) +{ +#ifdef CONFIG_S3C_DEV_HSMMC + s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio; +#endif +} + +static inline void s3c6410_default_sdhci1(void) +{ +#ifdef CONFIG_S3C_DEV_HSMMC1 + s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio; +#endif +} + +static inline void s3c6410_default_sdhci2(void) +{ +#ifdef CONFIG_S3C_DEV_HSMMC2 + s3c_hsmmc2_def_platdata.cfg_gpio = s3c64xx_setup_sdhci2_cfg_gpio; +#endif +} + +#else +static inline void s3c6410_default_sdhci0(void) { } +static inline void s3c6410_default_sdhci1(void) { } +static inline void s3c6410_default_sdhci2(void) { } +static inline void s3c6400_default_sdhci0(void) { } +static inline void s3c6400_default_sdhci1(void) { } +static inline void s3c6400_default_sdhci2(void) { } + +#endif /* CONFIG_S3C64XX_SETUP_SDHCI */ + +static inline void s3c_sdhci_setname(int id, char *name) +{ + switch (id) { +#ifdef CONFIG_S3C_DEV_HSMMC + case 0: + s3c_device_hsmmc0.name = name; + break; +#endif +#ifdef CONFIG_S3C_DEV_HSMMC1 + case 1: + s3c_device_hsmmc1.name = name; + break; +#endif +#ifdef CONFIG_S3C_DEV_HSMMC2 + case 2: + s3c_device_hsmmc2.name = name; + break; +#endif +#ifdef CONFIG_S3C_DEV_HSMMC3 + case 3: + s3c_device_hsmmc3.name = name; + break; +#endif + default: + break; + } +} +#endif /* __PLAT_S3C_SDHCI_H */ diff --git a/arch/arm/plat-samsung/include/plat/spi-core.h b/arch/arm/plat-samsung/include/plat/spi-core.h new file mode 100644 index 000000000..0b9428ab3 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/spi-core.h @@ -0,0 +1,30 @@ +/* + * Copyright (C) 2012 Heiko Stuebner + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __PLAT_S3C_SPI_CORE_H +#define __PLAT_S3C_SPI_CORE_H + +/* These functions are only for use with the core support code, such as + * the cpu specific initialisation code + */ + +/* re-define device name depending on support. */ +static inline void s3c64xx_spi_setname(char *name) +{ +#ifdef CONFIG_S3C64XX_DEV_SPI0 + s3c64xx_device_spi0.name = name; +#endif +#ifdef CONFIG_S3C64XX_DEV_SPI1 + s3c64xx_device_spi1.name = name; +#endif +#ifdef CONFIG_S3C64XX_DEV_SPI2 + s3c64xx_device_spi2.name = name; +#endif +} + +#endif /* __PLAT_S3C_SPI_CORE_H */ diff --git a/arch/arm/plat-samsung/include/plat/usb-phy.h b/arch/arm/plat-samsung/include/plat/usb-phy.h new file mode 100644 index 000000000..ab34dfadb --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/usb-phy.h @@ -0,0 +1,19 @@ +/* + * Copyright (C) 2011 Samsung Electronics Co.Ltd + * Author: Joonyoung Shim + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef __PLAT_SAMSUNG_USB_PHY_H +#define __PLAT_SAMSUNG_USB_PHY_H __FILE__ + +#include + +extern int s5p_usb_phy_init(struct platform_device *pdev, int type); +extern int s5p_usb_phy_exit(struct platform_device *pdev, int type); + +#endif /* __PLAT_SAMSUNG_USB_PHY_H */ diff --git a/arch/arm/plat-samsung/include/plat/wakeup-mask.h b/arch/arm/plat-samsung/include/plat/wakeup-mask.h new file mode 100644 index 000000000..43e4acd2e --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/wakeup-mask.h @@ -0,0 +1,44 @@ +/* arch/arm/plat-samsung/include/plat/wakeup-mask.h + * + * Copyright 2010 Ben Dooks + * + * Support for wakeup mask interrupts on newer SoCs + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#ifndef __PLAT_WAKEUP_MASK_H +#define __PLAT_WAKEUP_MASK_H __file__ + +/* if no irq yet defined, but still want to mask */ +#define NO_WAKEUP_IRQ (0x90000000) + +/** + * struct samsung_wakeup_mask - wakeup mask information + * @irq: The interrupt associated with this wakeup. + * @bit: The bit, as a (1 << bitno) controlling this source. + */ +struct samsung_wakeup_mask { + unsigned int irq; + u32 bit; +}; + +/** + * samsung_sync_wakemask - sync wakeup mask information for pm + * @reg: The register that is used. + * @masks: The list of masks to use. + * @nr_masks: The number of entries pointed to buy @masks. + * + * Synchronise the wakeup mask information at suspend time from the list + * of interrupts and control bits in @masks. We do this at suspend time + * as overriding the relevant irq chips is harder and the register is only + * required to be correct before we enter sleep. + */ +extern void samsung_sync_wakemask(void __iomem *reg, + struct samsung_wakeup_mask *masks, + int nr_masks); + +#endif /* __PLAT_WAKEUP_MASK_H */ diff --git a/arch/arm/plat-samsung/include/plat/watchdog-reset.h b/arch/arm/plat-samsung/include/plat/watchdog-reset.h new file mode 100644 index 000000000..0386b8f76 --- /dev/null +++ b/arch/arm/plat-samsung/include/plat/watchdog-reset.h @@ -0,0 +1,20 @@ +/* arch/arm/plat-s3c/include/plat/watchdog-reset.h + * + * Copyright (c) 2008 Simtec Electronics + * Ben Dooks + * + * S3C2410 - System define for arch_reset() function + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __PLAT_SAMSUNG_WATCHDOG_RESET_H +#define __PLAT_SAMSUNG_WATCHDOG_RESET_H + +extern void samsung_wdt_reset(void); +extern void samsung_wdt_reset_of_init(void); +extern void samsung_wdt_reset_init(void __iomem *base); + +#endif /* __PLAT_SAMSUNG_WATCHDOG_RESET_H */ -- cgit v1.2.3-54-g00ecf