From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- drivers/gpu/drm/gma500/psb_intel_reg.h | 1545 ++++++++++++++++++++++++++++++++ 1 file changed, 1545 insertions(+) create mode 100644 drivers/gpu/drm/gma500/psb_intel_reg.h (limited to 'drivers/gpu/drm/gma500/psb_intel_reg.h') diff --git a/drivers/gpu/drm/gma500/psb_intel_reg.h b/drivers/gpu/drm/gma500/psb_intel_reg.h new file mode 100644 index 000000000..0be30e4d1 --- /dev/null +++ b/drivers/gpu/drm/gma500/psb_intel_reg.h @@ -0,0 +1,1545 @@ +/* + * Copyright (c) 2009, Intel Corporation. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + */ +#ifndef __PSB_INTEL_REG_H__ +#define __PSB_INTEL_REG_H__ + +/* + * GPIO regs + */ +#define GPIOA 0x5010 +#define GPIOB 0x5014 +#define GPIOC 0x5018 +#define GPIOD 0x501c +#define GPIOE 0x5020 +#define GPIOF 0x5024 +#define GPIOG 0x5028 +#define GPIOH 0x502c +# define GPIO_CLOCK_DIR_MASK (1 << 0) +# define GPIO_CLOCK_DIR_IN (0 << 1) +# define GPIO_CLOCK_DIR_OUT (1 << 1) +# define GPIO_CLOCK_VAL_MASK (1 << 2) +# define GPIO_CLOCK_VAL_OUT (1 << 3) +# define GPIO_CLOCK_VAL_IN (1 << 4) +# define GPIO_CLOCK_PULLUP_DISABLE (1 << 5) +# define GPIO_DATA_DIR_MASK (1 << 8) +# define GPIO_DATA_DIR_IN (0 << 9) +# define GPIO_DATA_DIR_OUT (1 << 9) +# define GPIO_DATA_VAL_MASK (1 << 10) +# define GPIO_DATA_VAL_OUT (1 << 11) +# define GPIO_DATA_VAL_IN (1 << 12) +# define GPIO_DATA_PULLUP_DISABLE (1 << 13) + +#define GMBUS0 0x5100 /* clock/port select */ +#define GMBUS_RATE_100KHZ (0<<8) +#define GMBUS_RATE_50KHZ (1<<8) +#define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */ +#define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */ +#define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */ +#define GMBUS_PORT_DISABLED 0 +#define GMBUS_PORT_SSC 1 +#define GMBUS_PORT_VGADDC 2 +#define GMBUS_PORT_PANEL 3 +#define GMBUS_PORT_DPC 4 /* HDMIC */ +#define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */ + /* 6 reserved */ +#define GMBUS_PORT_DPD 7 /* HDMID */ +#define GMBUS_NUM_PORTS 8 +#define GMBUS1 0x5104 /* command/status */ +#define GMBUS_SW_CLR_INT (1<<31) +#define GMBUS_SW_RDY (1<<30) +#define GMBUS_ENT (1<<29) /* enable timeout */ +#define GMBUS_CYCLE_NONE (0<<25) +#define GMBUS_CYCLE_WAIT (1<<25) +#define GMBUS_CYCLE_INDEX (2<<25) +#define GMBUS_CYCLE_STOP (4<<25) +#define GMBUS_BYTE_COUNT_SHIFT 16 +#define GMBUS_SLAVE_INDEX_SHIFT 8 +#define GMBUS_SLAVE_ADDR_SHIFT 1 +#define GMBUS_SLAVE_READ (1<<0) +#define GMBUS_SLAVE_WRITE (0<<0) +#define GMBUS2 0x5108 /* status */ +#define GMBUS_INUSE (1<<15) +#define GMBUS_HW_WAIT_PHASE (1<<14) +#define GMBUS_STALL_TIMEOUT (1<<13) +#define GMBUS_INT (1<<12) +#define GMBUS_HW_RDY (1<<11) +#define GMBUS_SATOER (1<<10) +#define GMBUS_ACTIVE (1<<9) +#define GMBUS3 0x510c /* data buffer bytes 3-0 */ +#define GMBUS4 0x5110 /* interrupt mask (Pineview+) */ +#define GMBUS_SLAVE_TIMEOUT_EN (1<<4) +#define GMBUS_NAK_EN (1<<3) +#define GMBUS_IDLE_EN (1<<2) +#define GMBUS_HW_WAIT_EN (1<<1) +#define GMBUS_HW_RDY_EN (1<<0) +#define GMBUS5 0x5120 /* byte index */ +#define GMBUS_2BYTE_INDEX_EN (1<<31) + +#define BLC_PWM_CTL 0x61254 +#define BLC_PWM_CTL2 0x61250 +#define PWM_ENABLE (1 << 31) +#define PWM_LEGACY_MODE (1 << 30) +#define PWM_PIPE_B (1 << 29) +#define BLC_PWM_CTL_C 0x62254 +#define BLC_PWM_CTL2_C 0x62250 +#define BACKLIGHT_MODULATION_FREQ_SHIFT (17) +/* + * This is the most significant 15 bits of the number of backlight cycles in a + * complete cycle of the modulated backlight control. + * + * The actual value is this field multiplied by two. + */ +#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17) +#define BLM_LEGACY_MODE (1 << 16) +/* + * This is the number of cycles out of the backlight modulation cycle for which + * the backlight is on. + * + * This field must be no greater than the number of cycles in the complete + * backlight modulation cycle. + */ +#define BACKLIGHT_DUTY_CYCLE_SHIFT (0) +#define BACKLIGHT_DUTY_CYCLE_MASK (0xffff) + +#define I915_GCFGC 0xf0 +#define I915_LOW_FREQUENCY_ENABLE (1 << 7) +#define I915_DISPLAY_CLOCK_190_200_MHZ (0 << 4) +#define I915_DISPLAY_CLOCK_333_MHZ (4 << 4) +#define I915_DISPLAY_CLOCK_MASK (7 << 4) + +#define I855_HPLLCC 0xc0 +#define I855_CLOCK_CONTROL_MASK (3 << 0) +#define I855_CLOCK_133_200 (0 << 0) +#define I855_CLOCK_100_200 (1 << 0) +#define I855_CLOCK_100_133 (2 << 0) +#define I855_CLOCK_166_250 (3 << 0) + +/* I830 CRTC registers */ +#define HTOTAL_A 0x60000 +#define HBLANK_A 0x60004 +#define HSYNC_A 0x60008 +#define VTOTAL_A 0x6000c +#define VBLANK_A 0x60010 +#define VSYNC_A 0x60014 +#define PIPEASRC 0x6001c +#define BCLRPAT_A 0x60020 +#define VSYNCSHIFT_A 0x60028 + +#define HTOTAL_B 0x61000 +#define HBLANK_B 0x61004 +#define HSYNC_B 0x61008 +#define VTOTAL_B 0x6100c +#define VBLANK_B 0x61010 +#define VSYNC_B 0x61014 +#define PIPEBSRC 0x6101c +#define BCLRPAT_B 0x61020 +#define VSYNCSHIFT_B 0x61028 + +#define HTOTAL_C 0x62000 +#define HBLANK_C 0x62004 +#define HSYNC_C 0x62008 +#define VTOTAL_C 0x6200c +#define VBLANK_C 0x62010 +#define VSYNC_C 0x62014 +#define PIPECSRC 0x6201c +#define BCLRPAT_C 0x62020 +#define VSYNCSHIFT_C 0x62028 + +#define PP_STATUS 0x61200 +# define PP_ON (1 << 31) +/* + * Indicates that all dependencies of the panel are on: + * + * - PLL enabled + * - pipe enabled + * - LVDS/DVOB/DVOC on + */ +#define PP_READY (1 << 30) +#define PP_SEQUENCE_NONE (0 << 28) +#define PP_SEQUENCE_ON (1 << 28) +#define PP_SEQUENCE_OFF (2 << 28) +#define PP_SEQUENCE_MASK 0x30000000 +#define PP_CYCLE_DELAY_ACTIVE (1 << 27) +#define PP_SEQUENCE_STATE_ON_IDLE (1 << 3) +#define PP_SEQUENCE_STATE_MASK 0x0000000f + +#define PP_CONTROL 0x61204 +#define POWER_TARGET_ON (1 << 0) +#define PANEL_UNLOCK_REGS (0xabcd << 16) +#define PANEL_UNLOCK_MASK (0xffff << 16) +#define EDP_FORCE_VDD (1 << 3) +#define EDP_BLC_ENABLE (1 << 2) +#define PANEL_POWER_RESET (1 << 1) +#define PANEL_POWER_OFF (0 << 0) +#define PANEL_POWER_ON (1 << 0) + +/* Poulsbo/Oaktrail */ +#define LVDSPP_ON 0x61208 +#define LVDSPP_OFF 0x6120c +#define PP_CYCLE 0x61210 + +/* Cedartrail */ +#define PP_ON_DELAYS 0x61208 /* Cedartrail */ +#define PANEL_PORT_SELECT_MASK (3 << 30) +#define PANEL_PORT_SELECT_LVDS (0 << 30) +#define PANEL_PORT_SELECT_EDP (1 << 30) +#define PANEL_POWER_UP_DELAY_MASK (0x1fff0000) +#define PANEL_POWER_UP_DELAY_SHIFT 16 +#define PANEL_LIGHT_ON_DELAY_MASK (0x1fff) +#define PANEL_LIGHT_ON_DELAY_SHIFT 0 + +#define PP_OFF_DELAYS 0x6120c /* Cedartrail */ +#define PANEL_POWER_DOWN_DELAY_MASK (0x1fff0000) +#define PANEL_POWER_DOWN_DELAY_SHIFT 16 +#define PANEL_LIGHT_OFF_DELAY_MASK (0x1fff) +#define PANEL_LIGHT_OFF_DELAY_SHIFT 0 + +#define PP_DIVISOR 0x61210 /* Cedartrail */ +#define PP_REFERENCE_DIVIDER_MASK (0xffffff00) +#define PP_REFERENCE_DIVIDER_SHIFT 8 +#define PANEL_POWER_CYCLE_DELAY_MASK (0x1f) +#define PANEL_POWER_CYCLE_DELAY_SHIFT 0 + +#define PFIT_CONTROL 0x61230 +#define PFIT_ENABLE (1 << 31) +#define PFIT_PIPE_MASK (3 << 29) +#define PFIT_PIPE_SHIFT 29 +#define PFIT_SCALING_MODE_PILLARBOX (1 << 27) +#define PFIT_SCALING_MODE_LETTERBOX (3 << 26) +#define VERT_INTERP_DISABLE (0 << 10) +#define VERT_INTERP_BILINEAR (1 << 10) +#define VERT_INTERP_MASK (3 << 10) +#define VERT_AUTO_SCALE (1 << 9) +#define HORIZ_INTERP_DISABLE (0 << 6) +#define HORIZ_INTERP_BILINEAR (1 << 6) +#define HORIZ_INTERP_MASK (3 << 6) +#define HORIZ_AUTO_SCALE (1 << 5) +#define PANEL_8TO6_DITHER_ENABLE (1 << 3) + +#define PFIT_PGM_RATIOS 0x61234 +#define PFIT_VERT_SCALE_MASK 0xfff00000 +#define PFIT_HORIZ_SCALE_MASK 0x0000fff0 + +#define PFIT_AUTO_RATIOS 0x61238 + +#define DPLL_A 0x06014 +#define DPLL_B 0x06018 +#define DPLL_VCO_ENABLE (1 << 31) +#define DPLL_DVO_HIGH_SPEED (1 << 30) +#define DPLL_SYNCLOCK_ENABLE (1 << 29) +#define DPLL_VGA_MODE_DIS (1 << 28) +#define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */ +#define DPLLB_MODE_LVDS (2 << 26) /* i915 */ +#define DPLL_MODE_MASK (3 << 26) +#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */ +#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */ +#define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */ +#define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */ +#define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */ +#define DPLL_FPA0h1_P1_POST_DIV_MASK 0x00ff0000 /* i915 */ +#define DPLL_LOCK (1 << 15) /* CDV */ + +/* + * The i830 generation, in DAC/serial mode, defines p1 as two plus this + * bitfield, or just 2 if PLL_P1_DIVIDE_BY_TWO is set. + */ +# define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000 +/* + * The i830 generation, in LVDS mode, defines P1 as the bit number set within + * this field (only one bit may be set). + */ +#define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000 +#define DPLL_FPA01_P1_POST_DIV_SHIFT 16 +#define PLL_P2_DIVIDE_BY_4 (1 << 23) /* i830, required + * in DVO non-gang */ +# define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */ +#define PLL_REF_INPUT_DREFCLK (0 << 13) +#define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */ +#define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO + * TVCLKIN */ +#define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13) +#define PLL_REF_INPUT_MASK (3 << 13) +#define PLL_LOAD_PULSE_PHASE_SHIFT 9 +/* + * Parallel to Serial Load Pulse phase selection. + * Selects the phase for the 10X DPLL clock for the PCIe + * digital display port. The range is 4 to 13; 10 or more + * is just a flip delay. The default is 6 + */ +#define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT) +#define DISPLAY_RATE_SELECT_FPA1 (1 << 8) + +/* + * SDVO multiplier for 945G/GM. Not used on 965. + * + * DPLL_MD_UDI_MULTIPLIER_MASK + */ +#define SDVO_MULTIPLIER_MASK 0x000000ff +#define SDVO_MULTIPLIER_SHIFT_HIRES 4 +#define SDVO_MULTIPLIER_SHIFT_VGA 0 + +/* + * PLL_MD + */ +/* Pipe A SDVO/UDI clock multiplier/divider register for G965. */ +#define DPLL_A_MD 0x0601c +/* Pipe B SDVO/UDI clock multiplier/divider register for G965. */ +#define DPLL_B_MD 0x06020 +/* + * UDI pixel divider, controlling how many pixels are stuffed into a packet. + * + * Value is pixels minus 1. Must be set to 1 pixel for SDVO. + */ +#define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000 +#define DPLL_MD_UDI_DIVIDER_SHIFT 24 +/* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */ +#define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000 +#define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16 +/* + * SDVO/UDI pixel multiplier. + * + * SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus + * clock rate is 10 times the DPLL clock. At low resolution/refresh rate + * modes, the bus rate would be below the limits, so SDVO allows for stuffing + * dummy bytes in the datastream at an increased clock rate, with both sides of + * the link knowing how many bytes are fill. + * + * So, for a mode with a dotclock of 65Mhz, we would want to double the clock + * rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be + * set to 130Mhz, and the SDVO multiplier set to 2x in this register and + * through an SDVO command. + * + * This register field has values of multiplication factor minus 1, with + * a maximum multiplier of 5 for SDVO. + */ +#define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00 +#define DPLL_MD_UDI_MULTIPLIER_SHIFT 8 +/* + * SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK. + * This best be set to the default value (3) or the CRT won't work. No, + * I don't entirely understand what this does... + */ +#define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f +#define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0 + +#define DPLL_TEST 0x606c +#define DPLLB_TEST_SDVO_DIV_1 (0 << 22) +#define DPLLB_TEST_SDVO_DIV_2 (1 << 22) +#define DPLLB_TEST_SDVO_DIV_4 (2 << 22) +#define DPLLB_TEST_SDVO_DIV_MASK (3 << 22) +#define DPLLB_TEST_N_BYPASS (1 << 19) +#define DPLLB_TEST_M_BYPASS (1 << 18) +#define DPLLB_INPUT_BUFFER_ENABLE (1 << 16) +#define DPLLA_TEST_N_BYPASS (1 << 3) +#define DPLLA_TEST_M_BYPASS (1 << 2) +#define DPLLA_INPUT_BUFFER_ENABLE (1 << 0) + +#define ADPA 0x61100 +#define ADPA_DAC_ENABLE (1 << 31) +#define ADPA_DAC_DISABLE 0 +#define ADPA_PIPE_SELECT_MASK (1 << 30) +#define ADPA_PIPE_A_SELECT 0 +#define ADPA_PIPE_B_SELECT (1 << 30) +#define ADPA_USE_VGA_HVPOLARITY (1 << 15) +#define ADPA_SETS_HVPOLARITY 0 +#define ADPA_VSYNC_CNTL_DISABLE (1 << 11) +#define ADPA_VSYNC_CNTL_ENABLE 0 +#define ADPA_HSYNC_CNTL_DISABLE (1 << 10) +#define ADPA_HSYNC_CNTL_ENABLE 0 +#define ADPA_VSYNC_ACTIVE_HIGH (1 << 4) +#define ADPA_VSYNC_ACTIVE_LOW 0 +#define ADPA_HSYNC_ACTIVE_HIGH (1 << 3) +#define ADPA_HSYNC_ACTIVE_LOW 0 + +#define FPA0 0x06040 +#define FPA1 0x06044 +#define FPB0 0x06048 +#define FPB1 0x0604c +#define FP_N_DIV_MASK 0x003f0000 +#define FP_N_DIV_SHIFT 16 +#define FP_M1_DIV_MASK 0x00003f00 +#define FP_M1_DIV_SHIFT 8 +#define FP_M2_DIV_MASK 0x0000003f +#define FP_M2_DIV_SHIFT 0 + +#define PORT_HOTPLUG_EN 0x61110 +#define HDMIB_HOTPLUG_INT_EN (1 << 29) +#define HDMIC_HOTPLUG_INT_EN (1 << 28) +#define HDMID_HOTPLUG_INT_EN (1 << 27) +#define SDVOB_HOTPLUG_INT_EN (1 << 26) +#define SDVOC_HOTPLUG_INT_EN (1 << 25) +#define TV_HOTPLUG_INT_EN (1 << 18) +#define CRT_HOTPLUG_INT_EN (1 << 9) +#define CRT_HOTPLUG_FORCE_DETECT (1 << 3) +/* CDV.. */ +#define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8) +#define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7) +#define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7) +#define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5) +#define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5) +#define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5) +#define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5) +#define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5) +#define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4) +#define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4) +#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2) +#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2) +#define CRT_HOTPLUG_DETECT_MASK 0x000000F8 + +#define PORT_HOTPLUG_STAT 0x61114 +#define CRT_HOTPLUG_INT_STATUS (1 << 11) +#define TV_HOTPLUG_INT_STATUS (1 << 10) +#define CRT_HOTPLUG_MONITOR_MASK (3 << 8) +#define CRT_HOTPLUG_MONITOR_COLOR (3 << 8) +#define CRT_HOTPLUG_MONITOR_MONO (2 << 8) +#define CRT_HOTPLUG_MONITOR_NONE (0 << 8) +#define SDVOC_HOTPLUG_INT_STATUS (1 << 7) +#define SDVOB_HOTPLUG_INT_STATUS (1 << 6) + +#define SDVOB 0x61140 +#define SDVOC 0x61160 +#define SDVO_ENABLE (1 << 31) +#define SDVO_PIPE_B_SELECT (1 << 30) +#define SDVO_STALL_SELECT (1 << 29) +#define SDVO_INTERRUPT_ENABLE (1 << 26) +#define SDVO_COLOR_RANGE_16_235 (1 << 8) +#define SDVO_AUDIO_ENABLE (1 << 6) + +/** + * 915G/GM SDVO pixel multiplier. + * + * Programmed value is multiplier - 1, up to 5x. + * + * DPLL_MD_UDI_MULTIPLIER_MASK + */ +#define SDVO_PORT_MULTIPLY_MASK (7 << 23) +#define SDVO_PORT_MULTIPLY_SHIFT 23 +#define SDVO_PHASE_SELECT_MASK (15 << 19) +#define SDVO_PHASE_SELECT_DEFAULT (6 << 19) +#define SDVO_CLOCK_OUTPUT_INVERT (1 << 18) +#define SDVOC_GANG_MODE (1 << 16) +#define SDVO_BORDER_ENABLE (1 << 7) +#define SDVOB_PCIE_CONCURRENCY (1 << 3) +#define SDVO_DETECTED (1 << 2) +/* Bits to be preserved when writing */ +#define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14)) +#define SDVOC_PRESERVE_MASK (1 << 17) + +/* + * This register controls the LVDS output enable, pipe selection, and data + * format selection. + * + * All of the clock/data pairs are force powered down by power sequencing. + */ +#define LVDS 0x61180 +/* + * Enables the LVDS port. This bit must be set before DPLLs are enabled, as + * the DPLL semantics change when the LVDS is assigned to that pipe. + */ +#define LVDS_PORT_EN (1 << 31) +/* Selects pipe B for LVDS data. Must be set on pre-965. */ +#define LVDS_PIPEB_SELECT (1 << 30) + +/* Turns on border drawing to allow centered display. */ +#define LVDS_BORDER_EN (1 << 15) + +/* + * Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per + * pixel. + */ +#define LVDS_A0A2_CLKA_POWER_MASK (3 << 8) +#define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8) +#define LVDS_A0A2_CLKA_POWER_UP (3 << 8) +/* + * Controls the A3 data pair, which contains the additional LSBs for 24 bit + * mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be + * on. + */ +#define LVDS_A3_POWER_MASK (3 << 6) +#define LVDS_A3_POWER_DOWN (0 << 6) +#define LVDS_A3_POWER_UP (3 << 6) +/* + * Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP + * is set. + */ +#define LVDS_CLKB_POWER_MASK (3 << 4) +#define LVDS_CLKB_POWER_DOWN (0 << 4) +#define LVDS_CLKB_POWER_UP (3 << 4) +/* + * Controls the B0-B3 data pairs. This must be set to match the DPLL p2 + * setting for whether we are in dual-channel mode. The B3 pair will + * additionally only be powered up when LVDS_A3_POWER_UP is set. + */ +#define LVDS_B0B3_POWER_MASK (3 << 2) +#define LVDS_B0B3_POWER_DOWN (0 << 2) +#define LVDS_B0B3_POWER_UP (3 << 2) + +#define PIPEACONF 0x70008 +#define PIPEACONF_ENABLE (1 << 31) +#define PIPEACONF_DISABLE 0 +#define PIPEACONF_DOUBLE_WIDE (1 << 30) +#define PIPECONF_ACTIVE (1 << 30) +#define PIPECONF_DSIPLL_LOCK (1 << 29) +#define PIPEACONF_SINGLE_WIDE 0 +#define PIPEACONF_PIPE_UNLOCKED 0 +#define PIPEACONF_DSR (1 << 26) +#define PIPEACONF_PIPE_LOCKED (1 << 25) +#define PIPEACONF_PALETTE 0 +#define PIPECONF_FORCE_BORDER (1 << 25) +#define PIPEACONF_GAMMA (1 << 24) +#define PIPECONF_PROGRESSIVE (0 << 21) +#define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21) +#define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21) +#define PIPECONF_PLANE_OFF (1 << 19) +#define PIPECONF_CURSOR_OFF (1 << 18) + +#define PIPEBCONF 0x71008 +#define PIPEBCONF_ENABLE (1 << 31) +#define PIPEBCONF_DISABLE 0 +#define PIPEBCONF_DOUBLE_WIDE (1 << 30) +#define PIPEBCONF_DISABLE 0 +#define PIPEBCONF_GAMMA (1 << 24) +#define PIPEBCONF_PALETTE 0 + +#define PIPECCONF 0x72008 + +#define PIPEBGCMAXRED 0x71010 +#define PIPEBGCMAXGREEN 0x71014 +#define PIPEBGCMAXBLUE 0x71018 + +#define PIPEASTAT 0x70024 +#define PIPEBSTAT 0x71024 +#define PIPECSTAT 0x72024 +#define PIPE_VBLANK_INTERRUPT_STATUS (1UL << 1) +#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL << 2) +#define PIPE_VBLANK_CLEAR (1 << 1) +#define PIPE_VBLANK_STATUS (1 << 1) +#define PIPE_TE_STATUS (1UL << 6) +#define PIPE_DPST_EVENT_STATUS (1UL << 7) +#define PIPE_VSYNC_CLEAR (1UL << 9) +#define PIPE_VSYNC_STATUS (1UL << 9) +#define PIPE_HDMI_AUDIO_UNDERRUN_STATUS (1UL << 10) +#define PIPE_HDMI_AUDIO_BUFFER_DONE_STATUS (1UL << 11) +#define PIPE_VBLANK_INTERRUPT_ENABLE (1UL << 17) +#define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL << 18) +#define PIPE_TE_ENABLE (1UL << 22) +#define PIPE_LEGACY_BLC_EVENT_ENABLE (1UL << 22) +#define PIPE_DPST_EVENT_ENABLE (1UL << 23) +#define PIPE_VSYNC_ENABL (1UL << 25) +#define PIPE_HDMI_AUDIO_UNDERRUN (1UL << 26) +#define PIPE_HDMI_AUDIO_BUFFER_DONE (1UL << 27) +#define PIPE_FIFO_UNDERRUN (1UL << 31) +#define PIPE_HDMI_AUDIO_INT_MASK (PIPE_HDMI_AUDIO_UNDERRUN | \ + PIPE_HDMI_AUDIO_BUFFER_DONE) +#define PIPE_EVENT_MASK ((1 << 29)|(1 << 28)|(1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)|(1 << 22)|(1 << 21)|(1 << 20)|(1 << 16)) +#define PIPE_VBLANK_MASK ((1 << 25)|(1 << 24)|(1 << 18)|(1 << 17)) +#define HISTOGRAM_INT_CONTROL 0x61268 +#define HISTOGRAM_BIN_DATA 0X61264 +#define HISTOGRAM_LOGIC_CONTROL 0x61260 +#define PWM_CONTROL_LOGIC 0x61250 +#define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL << 10) +#define HISTOGRAM_INTERRUPT_ENABLE (1UL << 31) +#define HISTOGRAM_LOGIC_ENABLE (1UL << 31) +#define PWM_LOGIC_ENABLE (1UL << 31) +#define PWM_PHASEIN_ENABLE (1UL << 25) +#define PWM_PHASEIN_INT_ENABLE (1UL << 24) +#define PWM_PHASEIN_VB_COUNT 0x00001f00 +#define PWM_PHASEIN_INC 0x0000001f +#define HISTOGRAM_INT_CTRL_CLEAR (1UL << 30) +#define DPST_YUV_LUMA_MODE 0 + +struct dpst_ie_histogram_control { + union { + uint32_t data; + struct { + uint32_t bin_reg_index:7; + uint32_t reserved:4; + uint32_t bin_reg_func_select:1; + uint32_t sync_to_phase_in:1; + uint32_t alt_enhancement_mode:2; + uint32_t reserved1:1; + uint32_t sync_to_phase_in_count:8; + uint32_t histogram_mode_select:1; + uint32_t reserved2:4; + uint32_t ie_pipe_assignment:1; + uint32_t ie_mode_table_enabled:1; + uint32_t ie_histogram_enable:1; + }; + }; +}; + +struct dpst_guardband { + union { + uint32_t data; + struct { + uint32_t guardband:22; + uint32_t guardband_interrupt_delay:8; + uint32_t interrupt_status:1; + uint32_t interrupt_enable:1; + }; + }; +}; + +#define PIPEAFRAMEHIGH 0x70040 +#define PIPEAFRAMEPIXEL 0x70044 +#define PIPEBFRAMEHIGH 0x71040 +#define PIPEBFRAMEPIXEL 0x71044 +#define PIPECFRAMEHIGH 0x72040 +#define PIPECFRAMEPIXEL 0x72044 +#define PIPE_FRAME_HIGH_MASK 0x0000ffff +#define PIPE_FRAME_HIGH_SHIFT 0 +#define PIPE_FRAME_LOW_MASK 0xff000000 +#define PIPE_FRAME_LOW_SHIFT 24 +#define PIPE_PIXEL_MASK 0x00ffffff +#define PIPE_PIXEL_SHIFT 0 + +#define FW_BLC_SELF 0x20e0 +#define FW_BLC_SELF_EN (1<<15) + +#define DSPARB 0x70030 +#define DSPFW1 0x70034 +#define DSP_FIFO_SR_WM_MASK 0xFF800000 +#define DSP_FIFO_SR_WM_SHIFT 23 +#define CURSOR_B_FIFO_WM_MASK 0x003F0000 +#define CURSOR_B_FIFO_WM_SHIFT 16 +#define DSPFW2 0x70038 +#define CURSOR_A_FIFO_WM_MASK 0x3F00 +#define CURSOR_A_FIFO_WM_SHIFT 8 +#define DSP_PLANE_C_FIFO_WM_MASK 0x7F +#define DSP_PLANE_C_FIFO_WM_SHIFT 0 +#define DSPFW3 0x7003c +#define DSPFW4 0x70050 +#define DSPFW5 0x70054 +#define DSP_PLANE_B_FIFO_WM1_SHIFT 24 +#define DSP_PLANE_A_FIFO_WM1_SHIFT 16 +#define CURSOR_B_FIFO_WM1_SHIFT 8 +#define CURSOR_FIFO_SR_WM1_SHIFT 0 +#define DSPFW6 0x70058 +#define DSPCHICKENBIT 0x70400 +#define DSPACNTR 0x70180 +#define DSPBCNTR 0x71180 +#define DSPCCNTR 0x72180 +#define DISPLAY_PLANE_ENABLE (1 << 31) +#define DISPLAY_PLANE_DISABLE 0 +#define DISPPLANE_GAMMA_ENABLE (1 << 30) +#define DISPPLANE_GAMMA_DISABLE 0 +#define DISPPLANE_PIXFORMAT_MASK (0xf << 26) +#define DISPPLANE_8BPP (0x2 << 26) +#define DISPPLANE_15_16BPP (0x4 << 26) +#define DISPPLANE_16BPP (0x5 << 26) +#define DISPPLANE_32BPP_NO_ALPHA (0x6 << 26) +#define DISPPLANE_32BPP (0x7 << 26) +#define DISPPLANE_STEREO_ENABLE (1 << 25) +#define DISPPLANE_STEREO_DISABLE 0 +#define DISPPLANE_SEL_PIPE_MASK (1 << 24) +#define DISPPLANE_SEL_PIPE_POS 24 +#define DISPPLANE_SEL_PIPE_A 0 +#define DISPPLANE_SEL_PIPE_B (1 << 24) +#define DISPPLANE_SRC_KEY_ENABLE (1 << 22) +#define DISPPLANE_SRC_KEY_DISABLE 0 +#define DISPPLANE_LINE_DOUBLE (1 << 20) +#define DISPPLANE_NO_LINE_DOUBLE 0 +#define DISPPLANE_STEREO_POLARITY_FIRST 0 +#define DISPPLANE_STEREO_POLARITY_SECOND (1 << 18) +/* plane B only */ +#define DISPPLANE_ALPHA_TRANS_ENABLE (1 << 15) +#define DISPPLANE_ALPHA_TRANS_DISABLE 0 +#define DISPPLANE_SPRITE_ABOVE_DISPLAYA 0 +#define DISPPLANE_SPRITE_ABOVE_OVERLAY (1) +#define DISPPLANE_BOTTOM (4) + +#define DSPABASE 0x70184 +#define DSPALINOFF 0x70184 +#define DSPASTRIDE 0x70188 + +#define DSPBBASE 0x71184 +#define DSPBLINOFF 0X71184 +#define DSPBADDR DSPBBASE +#define DSPBSTRIDE 0x71188 + +#define DSPCBASE 0x72184 +#define DSPCLINOFF 0x72184 +#define DSPCSTRIDE 0x72188 + +#define DSPAKEYVAL 0x70194 +#define DSPAKEYMASK 0x70198 + +#define DSPAPOS 0x7018C /* reserved */ +#define DSPASIZE 0x70190 +#define DSPBPOS 0x7118C +#define DSPBSIZE 0x71190 +#define DSPCPOS 0x7218C +#define DSPCSIZE 0x72190 + +#define DSPASURF 0x7019C +#define DSPATILEOFF 0x701A4 + +#define DSPBSURF 0x7119C +#define DSPBTILEOFF 0x711A4 + +#define DSPCSURF 0x7219C +#define DSPCTILEOFF 0x721A4 +#define DSPCKEYMAXVAL 0x721A0 +#define DSPCKEYMINVAL 0x72194 +#define DSPCKEYMSK 0x72198 + +#define VGACNTRL 0x71400 +#define VGA_DISP_DISABLE (1 << 31) +#define VGA_2X_MODE (1 << 30) +#define VGA_PIPE_B_SELECT (1 << 29) + +/* + * Overlay registers + */ +#define OV_C_OFFSET 0x08000 +#define OV_OVADD 0x30000 +#define OV_DOVASTA 0x30008 +# define OV_PIPE_SELECT ((1 << 6)|(1 << 7)) +# define OV_PIPE_SELECT_POS 6 +# define OV_PIPE_A 0 +# define OV_PIPE_C 1 +#define OV_OGAMC5 0x30010 +#define OV_OGAMC4 0x30014 +#define OV_OGAMC3 0x30018 +#define OV_OGAMC2 0x3001C +#define OV_OGAMC1 0x30020 +#define OV_OGAMC0 0x30024 +#define OVC_OVADD 0x38000 +#define OVC_DOVCSTA 0x38008 +#define OVC_OGAMC5 0x38010 +#define OVC_OGAMC4 0x38014 +#define OVC_OGAMC3 0x38018 +#define OVC_OGAMC2 0x3801C +#define OVC_OGAMC1 0x38020 +#define OVC_OGAMC0 0x38024 + +/* + * Some BIOS scratch area registers. The 845 (and 830?) store the amount + * of video memory available to the BIOS in SWF1. + */ +#define SWF0 0x71410 +#define SWF1 0x71414 +#define SWF2 0x71418 +#define SWF3 0x7141c +#define SWF4 0x71420 +#define SWF5 0x71424 +#define SWF6 0x71428 + +/* + * 855 scratch registers. + */ +#define SWF00 0x70410 +#define SWF01 0x70414 +#define SWF02 0x70418 +#define SWF03 0x7041c +#define SWF04 0x70420 +#define SWF05 0x70424 +#define SWF06 0x70428 + +#define SWF10 SWF0 +#define SWF11 SWF1 +#define SWF12 SWF2 +#define SWF13 SWF3 +#define SWF14 SWF4 +#define SWF15 SWF5 +#define SWF16 SWF6 + +#define SWF30 0x72414 +#define SWF31 0x72418 +#define SWF32 0x7241c + + +/* + * Palette registers + */ +#define PALETTE_A 0x0a000 +#define PALETTE_B 0x0a800 +#define PALETTE_C 0x0ac00 + +/* Cursor A & B regs */ +#define CURACNTR 0x70080 +#define CURSOR_MODE_DISABLE 0x00 +#define CURSOR_MODE_64_32B_AX 0x07 +#define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX) +#define MCURSOR_GAMMA_ENABLE (1 << 26) +#define CURABASE 0x70084 +#define CURAPOS 0x70088 +#define CURSOR_POS_MASK 0x007FF +#define CURSOR_POS_SIGN 0x8000 +#define CURSOR_X_SHIFT 0 +#define CURSOR_Y_SHIFT 16 +#define CURBCNTR 0x700c0 +#define CURBBASE 0x700c4 +#define CURBPOS 0x700c8 +#define CURCCNTR 0x700e0 +#define CURCBASE 0x700e4 +#define CURCPOS 0x700e8 + +/* + * Interrupt Registers + */ +#define IER 0x020a0 +#define IIR 0x020a4 +#define IMR 0x020a8 +#define ISR 0x020ac + +/* + * MOORESTOWN delta registers + */ +#define MRST_DPLL_A 0x0f014 +#define MDFLD_DPLL_B 0x0f018 +#define MDFLD_INPUT_REF_SEL (1 << 14) +#define MDFLD_VCO_SEL (1 << 16) +#define DPLLA_MODE_LVDS (2 << 26) /* mrst */ +#define MDFLD_PLL_LATCHEN (1 << 28) +#define MDFLD_PWR_GATE_EN (1 << 30) +#define MDFLD_P1_MASK (0x1FF << 17) +#define MRST_FPA0 0x0f040 +#define MRST_FPA1 0x0f044 +#define MDFLD_DPLL_DIV0 0x0f048 +#define MDFLD_DPLL_DIV1 0x0f04c +#define MRST_PERF_MODE 0x020f4 + +/* + * MEDFIELD HDMI registers + */ +#define HDMIPHYMISCCTL 0x61134 +#define HDMI_PHY_POWER_DOWN 0x7f +#define HDMIB_CONTROL 0x61140 +#define HDMIB_PORT_EN (1 << 31) +#define HDMIB_PIPE_B_SELECT (1 << 30) +#define HDMIB_NULL_PACKET (1 << 9) +#define HDMIB_HDCP_PORT (1 << 5) + +/* #define LVDS 0x61180 */ +#define MRST_PANEL_8TO6_DITHER_ENABLE (1 << 25) +#define MRST_PANEL_24_DOT_1_FORMAT (1 << 24) +#define LVDS_A3_POWER_UP_0_OUTPUT (1 << 6) + +#define MIPI 0x61190 +#define MIPI_C 0x62190 +#define MIPI_PORT_EN (1 << 31) +/* Turns on border drawing to allow centered display. */ +#define SEL_FLOPPED_HSTX (1 << 23) +#define PASS_FROM_SPHY_TO_AFE (1 << 16) +#define MIPI_BORDER_EN (1 << 15) +#define MIPIA_3LANE_MIPIC_1LANE 0x1 +#define MIPIA_2LANE_MIPIC_2LANE 0x2 +#define TE_TRIGGER_DSI_PROTOCOL (1 << 2) +#define TE_TRIGGER_GPIO_PIN (1 << 3) +#define MIPI_TE_COUNT 0x61194 + +/* #define PP_CONTROL 0x61204 */ +#define POWER_DOWN_ON_RESET (1 << 1) + +/* #define PFIT_CONTROL 0x61230 */ +#define PFIT_PIPE_SELECT (3 << 29) +#define PFIT_PIPE_SELECT_SHIFT (29) + +/* #define BLC_PWM_CTL 0x61254 */ +#define MRST_BACKLIGHT_MODULATION_FREQ_SHIFT (16) +#define MRST_BACKLIGHT_MODULATION_FREQ_MASK (0xffff << 16) + +/* #define PIPEACONF 0x70008 */ +#define PIPEACONF_PIPE_STATE (1 << 30) +/* #define DSPACNTR 0x70180 */ + +#define MRST_DSPABASE 0x7019c +#define MRST_DSPBBASE 0x7119c +#define MDFLD_DSPCBASE 0x7219c + +/* + * Moorestown registers. + */ + +/* + * MIPI IP registers + */ +#define MIPIC_REG_OFFSET 0x800 + +#define DEVICE_READY_REG 0xb000 +#define LP_OUTPUT_HOLD (1 << 16) +#define EXIT_ULPS_DEV_READY 0x3 +#define LP_OUTPUT_HOLD_RELEASE 0x810000 +# define ENTERING_ULPS (2 << 1) +# define EXITING_ULPS (1 << 1) +# define ULPS_MASK (3 << 1) +# define BUS_POSSESSION (1 << 3) +#define INTR_STAT_REG 0xb004 +#define RX_SOT_ERROR (1 << 0) +#define RX_SOT_SYNC_ERROR (1 << 1) +#define RX_ESCAPE_MODE_ENTRY_ERROR (1 << 3) +#define RX_LP_TX_SYNC_ERROR (1 << 4) +#define RX_HS_RECEIVE_TIMEOUT_ERROR (1 << 5) +#define RX_FALSE_CONTROL_ERROR (1 << 6) +#define RX_ECC_SINGLE_BIT_ERROR (1 << 7) +#define RX_ECC_MULTI_BIT_ERROR (1 << 8) +#define RX_CHECKSUM_ERROR (1 << 9) +#define RX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 10) +#define RX_DSI_VC_ID_INVALID (1 << 11) +#define TX_FALSE_CONTROL_ERROR (1 << 12) +#define TX_ECC_SINGLE_BIT_ERROR (1 << 13) +#define TX_ECC_MULTI_BIT_ERROR (1 << 14) +#define TX_CHECKSUM_ERROR (1 << 15) +#define TX_DSI_DATA_TYPE_NOT_RECOGNIZED (1 << 16) +#define TX_DSI_VC_ID_INVALID (1 << 17) +#define HIGH_CONTENTION (1 << 18) +#define LOW_CONTENTION (1 << 19) +#define DPI_FIFO_UNDER_RUN (1 << 20) +#define HS_TX_TIMEOUT (1 << 21) +#define LP_RX_TIMEOUT (1 << 22) +#define TURN_AROUND_ACK_TIMEOUT (1 << 23) +#define ACK_WITH_NO_ERROR (1 << 24) +#define HS_GENERIC_WR_FIFO_FULL (1 << 27) +#define LP_GENERIC_WR_FIFO_FULL (1 << 28) +#define SPL_PKT_SENT (1 << 30) +#define INTR_EN_REG 0xb008 +#define DSI_FUNC_PRG_REG 0xb00c +#define DPI_CHANNEL_NUMBER_POS 0x03 +#define DBI_CHANNEL_NUMBER_POS 0x05 +#define FMT_DPI_POS 0x07 +#define FMT_DBI_POS 0x0A +#define DBI_DATA_WIDTH_POS 0x0D + +/* DPI PIXEL FORMATS */ +#define RGB_565_FMT 0x01 /* RGB 565 FORMAT */ +#define RGB_666_FMT 0x02 /* RGB 666 FORMAT */ +#define LRGB_666_FMT 0x03 /* RGB LOOSELY PACKED + * 666 FORMAT + */ +#define RGB_888_FMT 0x04 /* RGB 888 FORMAT */ +#define VIRTUAL_CHANNEL_NUMBER_0 0x00 /* Virtual channel 0 */ +#define VIRTUAL_CHANNEL_NUMBER_1 0x01 /* Virtual channel 1 */ +#define VIRTUAL_CHANNEL_NUMBER_2 0x02 /* Virtual channel 2 */ +#define VIRTUAL_CHANNEL_NUMBER_3 0x03 /* Virtual channel 3 */ + +#define DBI_NOT_SUPPORTED 0x00 /* command mode + * is not supported + */ +#define DBI_DATA_WIDTH_16BIT 0x01 /* 16 bit data */ +#define DBI_DATA_WIDTH_9BIT 0x02 /* 9 bit data */ +#define DBI_DATA_WIDTH_8BIT 0x03 /* 8 bit data */ +#define DBI_DATA_WIDTH_OPT1 0x04 /* option 1 */ +#define DBI_DATA_WIDTH_OPT2 0x05 /* option 2 */ + +#define HS_TX_TIMEOUT_REG 0xb010 +#define LP_RX_TIMEOUT_REG 0xb014 +#define TURN_AROUND_TIMEOUT_REG 0xb018 +#define DEVICE_RESET_REG 0xb01C +#define DPI_RESOLUTION_REG 0xb020 +#define RES_V_POS 0x10 +#define DBI_RESOLUTION_REG 0xb024 /* Reserved for MDFLD */ +#define HORIZ_SYNC_PAD_COUNT_REG 0xb028 +#define HORIZ_BACK_PORCH_COUNT_REG 0xb02C +#define HORIZ_FRONT_PORCH_COUNT_REG 0xb030 +#define HORIZ_ACTIVE_AREA_COUNT_REG 0xb034 +#define VERT_SYNC_PAD_COUNT_REG 0xb038 +#define VERT_BACK_PORCH_COUNT_REG 0xb03c +#define VERT_FRONT_PORCH_COUNT_REG 0xb040 +#define HIGH_LOW_SWITCH_COUNT_REG 0xb044 +#define DPI_CONTROL_REG 0xb048 +#define DPI_SHUT_DOWN (1 << 0) +#define DPI_TURN_ON (1 << 1) +#define DPI_COLOR_MODE_ON (1 << 2) +#define DPI_COLOR_MODE_OFF (1 << 3) +#define DPI_BACK_LIGHT_ON (1 << 4) +#define DPI_BACK_LIGHT_OFF (1 << 5) +#define DPI_LP (1 << 6) +#define DPI_DATA_REG 0xb04c +#define DPI_BACK_LIGHT_ON_DATA 0x07 +#define DPI_BACK_LIGHT_OFF_DATA 0x17 +#define INIT_COUNT_REG 0xb050 +#define MAX_RET_PAK_REG 0xb054 +#define VIDEO_FMT_REG 0xb058 +#define COMPLETE_LAST_PCKT (1 << 2) +#define EOT_DISABLE_REG 0xb05c +#define ENABLE_CLOCK_STOPPING (1 << 1) +#define LP_BYTECLK_REG 0xb060 +#define LP_GEN_DATA_REG 0xb064 +#define HS_GEN_DATA_REG 0xb068 +#define LP_GEN_CTRL_REG 0xb06C +#define HS_GEN_CTRL_REG 0xb070 +#define DCS_CHANNEL_NUMBER_POS 0x6 +#define MCS_COMMANDS_POS 0x8 +#define WORD_COUNTS_POS 0x8 +#define MCS_PARAMETER_POS 0x10 +#define GEN_FIFO_STAT_REG 0xb074 +#define HS_DATA_FIFO_FULL (1 << 0) +#define HS_DATA_FIFO_HALF_EMPTY (1 << 1) +#define HS_DATA_FIFO_EMPTY (1 << 2) +#define LP_DATA_FIFO_FULL (1 << 8) +#define LP_DATA_FIFO_HALF_EMPTY (1 << 9) +#define LP_DATA_FIFO_EMPTY (1 << 10) +#define HS_CTRL_FIFO_FULL (1 << 16) +#define HS_CTRL_FIFO_HALF_EMPTY (1 << 17) +#define HS_CTRL_FIFO_EMPTY (1 << 18) +#define LP_CTRL_FIFO_FULL (1 << 24) +#define LP_CTRL_FIFO_HALF_EMPTY (1 << 25) +#define LP_CTRL_FIFO_EMPTY (1 << 26) +#define DBI_FIFO_EMPTY (1 << 27) +#define DPI_FIFO_EMPTY (1 << 28) +#define HS_LS_DBI_ENABLE_REG 0xb078 +#define TXCLKESC_REG 0xb07c +#define DPHY_PARAM_REG 0xb080 +#define DBI_BW_CTRL_REG 0xb084 +#define CLK_LANE_SWT_REG 0xb088 + +/* + * MIPI Adapter registers + */ +#define MIPI_CONTROL_REG 0xb104 +#define MIPI_2X_CLOCK_BITS ((1 << 0) | (1 << 1)) +#define MIPI_DATA_ADDRESS_REG 0xb108 +#define MIPI_DATA_LENGTH_REG 0xb10C +#define MIPI_COMMAND_ADDRESS_REG 0xb110 +#define MIPI_COMMAND_LENGTH_REG 0xb114 +#define MIPI_READ_DATA_RETURN_REG0 0xb118 +#define MIPI_READ_DATA_RETURN_REG1 0xb11C +#define MIPI_READ_DATA_RETURN_REG2 0xb120 +#define MIPI_READ_DATA_RETURN_REG3 0xb124 +#define MIPI_READ_DATA_RETURN_REG4 0xb128 +#define MIPI_READ_DATA_RETURN_REG5 0xb12C +#define MIPI_READ_DATA_RETURN_REG6 0xb130 +#define MIPI_READ_DATA_RETURN_REG7 0xb134 +#define MIPI_READ_DATA_VALID_REG 0xb138 + +/* DBI COMMANDS */ +#define soft_reset 0x01 +/* + * The display module performs a software reset. + * Registers are written with their SW Reset default values. + */ +#define get_power_mode 0x0a +/* + * The display module returns the current power mode + */ +#define get_address_mode 0x0b +/* + * The display module returns the current status. + */ +#define get_pixel_format 0x0c +/* + * This command gets the pixel format for the RGB image data + * used by the interface. + */ +#define get_display_mode 0x0d +/* + * The display module returns the Display Image Mode status. + */ +#define get_signal_mode 0x0e +/* + * The display module returns the Display Signal Mode. + */ +#define get_diagnostic_result 0x0f +/* + * The display module returns the self-diagnostic results following + * a Sleep Out command. + */ +#define enter_sleep_mode 0x10 +/* + * This command causes the display module to enter the Sleep mode. + * In this mode, all unnecessary blocks inside the display module are + * disabled except interface communication. This is the lowest power + * mode the display module supports. + */ +#define exit_sleep_mode 0x11 +/* + * This command causes the display module to exit Sleep mode. + * All blocks inside the display module are enabled. + */ +#define enter_partial_mode 0x12 +/* + * This command causes the display module to enter the Partial Display + * Mode. The Partial Display Mode window is described by the + * set_partial_area command. + */ +#define enter_normal_mode 0x13 +/* + * This command causes the display module to enter the Normal mode. + * Normal Mode is defined as Partial Display mode and Scroll mode are off + */ +#define exit_invert_mode 0x20 +/* + * This command causes the display module to stop inverting the image + * data on the display device. The frame memory contents remain unchanged. + * No status bits are changed. + */ +#define enter_invert_mode 0x21 +/* + * This command causes the display module to invert the image data only on + * the display device. The frame memory contents remain unchanged. + * No status bits are changed. + */ +#define set_gamma_curve 0x26 +/* + * This command selects the desired gamma curve for the display device. + * Four fixed gamma curves are defined in section DCS spec. + */ +#define set_display_off 0x28 +/* ************************************************************************* *\ +This command causes the display module to stop displaying the image data +on the display device. The frame memory contents remain unchanged. +No status bits are changed. +\* ************************************************************************* */ +#define set_display_on 0x29 +/* ************************************************************************* *\ +This command causes the display module to start displaying the image data +on the display device. The frame memory contents remain unchanged. +No status bits are changed. +\* ************************************************************************* */ +#define set_column_address 0x2a +/* + * This command defines the column extent of the frame memory accessed by + * the hostprocessor with the read_memory_continue and + * write_memory_continue commands. + * No status bits are changed. + */ +#define set_page_addr 0x2b +/* + * This command defines the page extent of the frame memory accessed by + * the host processor with the write_memory_continue and + * read_memory_continue command. + * No status bits are changed. + */ +#define write_mem_start 0x2c +/* + * This command transfers image data from the host processor to the + * display modules frame memory starting at the pixel location specified + * by preceding set_column_address and set_page_address commands. + */ +#define set_partial_area 0x30 +/* + * This command defines the Partial Display mode s display area. + * There are two parameters associated with this command, the first + * defines the Start Row (SR) and the second the End Row (ER). SR and ER + * refer to the Frame Memory Line Pointer. + */ +#define set_scroll_area 0x33 +/* + * This command defines the display modules Vertical Scrolling Area. + */ +#define set_tear_off 0x34 +/* + * This command turns off the display modules Tearing Effect output + * signal on the TE signal line. + */ +#define set_tear_on 0x35 +/* + * This command turns on the display modules Tearing Effect output signal + * on the TE signal line. + */ +#define set_address_mode 0x36 +/* + * This command sets the data order for transfers from the host processor + * to display modules frame memory,bits B[7:5] and B3, and from the + * display modules frame memory to the display device, bits B[2:0] and B4. + */ +#define set_scroll_start 0x37 +/* + * This command sets the start of the vertical scrolling area in the frame + * memory. The vertical scrolling area is fully defined when this command + * is used with the set_scroll_area command The set_scroll_start command + * has one parameter, the Vertical Scroll Pointer. The VSP defines the + * line in the frame memory that is written to the display device as the + * first line of the vertical scroll area. + */ +#define exit_idle_mode 0x38 +/* + * This command causes the display module to exit Idle mode. + */ +#define enter_idle_mode 0x39 +/* + * This command causes the display module to enter Idle Mode. + * In Idle Mode, color expression is reduced. Colors are shown on the + * display device using the MSB of each of the R, G and B color + * components in the frame memory + */ +#define set_pixel_format 0x3a +/* + * This command sets the pixel format for the RGB image data used by the + * interface. + * Bits D[6:4] DPI Pixel Format Definition + * Bits D[2:0] DBI Pixel Format Definition + * Bits D7 and D3 are not used. + */ +#define DCS_PIXEL_FORMAT_3bpp 0x1 +#define DCS_PIXEL_FORMAT_8bpp 0x2 +#define DCS_PIXEL_FORMAT_12bpp 0x3 +#define DCS_PIXEL_FORMAT_16bpp 0x5 +#define DCS_PIXEL_FORMAT_18bpp 0x6 +#define DCS_PIXEL_FORMAT_24bpp 0x7 + +#define write_mem_cont 0x3c + +/* + * This command transfers image data from the host processor to the + * display module's frame memory continuing from the pixel location + * following the previous write_memory_continue or write_memory_start + * command. + */ +#define set_tear_scanline 0x44 +/* + * This command turns on the display modules Tearing Effect output signal + * on the TE signal line when the display module reaches line N. + */ +#define get_scanline 0x45 +/* + * The display module returns the current scanline, N, used to update the + * display device. The total number of scanlines on a display device is + * defined as VSYNC + VBP + VACT + VFP.The first scanline is defined as + * the first line of V Sync and is denoted as Line 0. + * When in Sleep Mode, the value returned by get_scanline is undefined. + */ + +/* MCS or Generic COMMANDS */ +/* MCS/generic data type */ +#define GEN_SHORT_WRITE_0 0x03 /* generic short write, no parameters */ +#define GEN_SHORT_WRITE_1 0x13 /* generic short write, 1 parameters */ +#define GEN_SHORT_WRITE_2 0x23 /* generic short write, 2 parameters */ +#define GEN_READ_0 0x04 /* generic read, no parameters */ +#define GEN_READ_1 0x14 /* generic read, 1 parameters */ +#define GEN_READ_2 0x24 /* generic read, 2 parameters */ +#define GEN_LONG_WRITE 0x29 /* generic long write */ +#define MCS_SHORT_WRITE_0 0x05 /* MCS short write, no parameters */ +#define MCS_SHORT_WRITE_1 0x15 /* MCS short write, 1 parameters */ +#define MCS_READ 0x06 /* MCS read, no parameters */ +#define MCS_LONG_WRITE 0x39 /* MCS long write */ +/* MCS/generic commands */ +/* TPO MCS */ +#define write_display_profile 0x50 +#define write_display_brightness 0x51 +#define write_ctrl_display 0x53 +#define write_ctrl_cabc 0x55 + #define UI_IMAGE 0x01 + #define STILL_IMAGE 0x02 + #define MOVING_IMAGE 0x03 +#define write_hysteresis 0x57 +#define write_gamma_setting 0x58 +#define write_cabc_min_bright 0x5e +#define write_kbbc_profile 0x60 +/* TMD MCS */ +#define tmd_write_display_brightness 0x8c + +/* + * This command is used to control ambient light, panel backlight + * brightness and gamma settings. + */ +#define BRIGHT_CNTL_BLOCK_ON (1 << 5) +#define AMBIENT_LIGHT_SENSE_ON (1 << 4) +#define DISPLAY_DIMMING_ON (1 << 3) +#define BACKLIGHT_ON (1 << 2) +#define DISPLAY_BRIGHTNESS_AUTO (1 << 1) +#define GAMMA_AUTO (1 << 0) + +/* DCS Interface Pixel Formats */ +#define DCS_PIXEL_FORMAT_3BPP 0x1 +#define DCS_PIXEL_FORMAT_8BPP 0x2 +#define DCS_PIXEL_FORMAT_12BPP 0x3 +#define DCS_PIXEL_FORMAT_16BPP 0x5 +#define DCS_PIXEL_FORMAT_18BPP 0x6 +#define DCS_PIXEL_FORMAT_24BPP 0x7 +/* ONE PARAMETER READ DATA */ +#define addr_mode_data 0xfc +#define diag_res_data 0x00 +#define disp_mode_data 0x23 +#define pxl_fmt_data 0x77 +#define pwr_mode_data 0x74 +#define sig_mode_data 0x00 +/* TWO PARAMETERS READ DATA */ +#define scanline_data1 0xff +#define scanline_data2 0xff +#define NON_BURST_MODE_SYNC_PULSE 0x01 /* Non Burst Mode + * with Sync Pulse + */ +#define NON_BURST_MODE_SYNC_EVENTS 0x02 /* Non Burst Mode + * with Sync events + */ +#define BURST_MODE 0x03 /* Burst Mode */ +#define DBI_COMMAND_BUFFER_SIZE 0x240 /* 0x32 */ /* 0x120 */ + /* Allocate at least + * 0x100 Byte with 32 + * byte alignment + */ +#define DBI_DATA_BUFFER_SIZE 0x120 /* Allocate at least + * 0x100 Byte with 32 + * byte alignment + */ +#define DBI_CB_TIME_OUT 0xFFFF + +#define GEN_FB_TIME_OUT 2000 + +#define SKU_83 0x01 +#define SKU_100 0x02 +#define SKU_100L 0x04 +#define SKU_BYPASS 0x08 + +/* Some handy macros for playing with bitfields. */ +#define PSB_MASK(high, low) (((1<<((high)-(low)+1))-1)<<(low)) +#define SET_FIELD(value, field) (((value) << field ## _SHIFT) & field ## _MASK) +#define GET_FIELD(word, field) (((word) & field ## _MASK) >> field ## _SHIFT) + +#define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a))) + +/* PCI config space */ + +#define SB_PCKT 0x02100 /* cedarview */ +# define SB_OPCODE_MASK PSB_MASK(31, 16) +# define SB_OPCODE_SHIFT 16 +# define SB_OPCODE_READ 0 +# define SB_OPCODE_WRITE 1 +# define SB_DEST_MASK PSB_MASK(15, 8) +# define SB_DEST_SHIFT 8 +# define SB_DEST_DPLL 0x88 +# define SB_BYTE_ENABLE_MASK PSB_MASK(7, 4) +# define SB_BYTE_ENABLE_SHIFT 4 +# define SB_BUSY (1 << 0) + +#define DSPCLK_GATE_D 0x6200 +# define VRHUNIT_CLOCK_GATE_DISABLE (1 << 28) /* Fixed value on CDV */ +# define DPOUNIT_CLOCK_GATE_DISABLE (1 << 11) +# define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6) +# define DPUNIT_PIPEB_GATE_DISABLE (1 << 30) +# define DPUNIT_PIPEA_GATE_DISABLE (1 << 25) +# define DPCUNIT_CLOCK_GATE_DISABLE (1 << 24) +# define DPLSUNIT_CLOCK_GATE_DISABLE (1 << 13) + +#define RAMCLK_GATE_D 0x6210 + +/* 32-bit value read/written from the DPIO reg. */ +#define SB_DATA 0x02104 /* cedarview */ +/* 32-bit address of the DPIO reg to be read/written. */ +#define SB_ADDR 0x02108 /* cedarview */ +#define DPIO_CFG 0x02110 /* cedarview */ +# define DPIO_MODE_SELECT_1 (1 << 3) +# define DPIO_MODE_SELECT_0 (1 << 2) +# define DPIO_SFR_BYPASS (1 << 1) +/* reset is active low */ +# define DPIO_CMN_RESET_N (1 << 0) + +/* Cedarview sideband registers */ +#define _SB_M_A 0x8008 +#define _SB_M_B 0x8028 +#define SB_M(pipe) _PIPE(pipe, _SB_M_A, _SB_M_B) +# define SB_M_DIVIDER_MASK (0xFF << 24) +# define SB_M_DIVIDER_SHIFT 24 + +#define _SB_N_VCO_A 0x8014 +#define _SB_N_VCO_B 0x8034 +#define SB_N_VCO(pipe) _PIPE(pipe, _SB_N_VCO_A, _SB_N_VCO_B) +#define SB_N_VCO_SEL_MASK PSB_MASK(31, 30) +#define SB_N_VCO_SEL_SHIFT 30 +#define SB_N_DIVIDER_MASK PSB_MASK(29, 26) +#define SB_N_DIVIDER_SHIFT 26 +#define SB_N_CB_TUNE_MASK PSB_MASK(25, 24) +#define SB_N_CB_TUNE_SHIFT 24 + +/* the bit 14:13 is used to select between the different reference clock for Pipe A/B */ +#define SB_REF_DPLLA 0x8010 +#define SB_REF_DPLLB 0x8030 +#define REF_CLK_MASK (0x3 << 13) +#define REF_CLK_CORE (0 << 13) +#define REF_CLK_DPLL (1 << 13) +#define REF_CLK_DPLLA (2 << 13) +/* For the DPLL B, it will use the reference clk from DPLL A when using (2 << 13) */ + +#define _SB_REF_A 0x8018 +#define _SB_REF_B 0x8038 +#define SB_REF_SFR(pipe) _PIPE(pipe, _SB_REF_A, _SB_REF_B) + +#define _SB_P_A 0x801c +#define _SB_P_B 0x803c +#define SB_P(pipe) _PIPE(pipe, _SB_P_A, _SB_P_B) +#define SB_P2_DIVIDER_MASK PSB_MASK(31, 30) +#define SB_P2_DIVIDER_SHIFT 30 +#define SB_P2_10 0 /* HDMI, DP, DAC */ +#define SB_P2_5 1 /* DAC */ +#define SB_P2_14 2 /* LVDS single */ +#define SB_P2_7 3 /* LVDS double */ +#define SB_P1_DIVIDER_MASK PSB_MASK(15, 12) +#define SB_P1_DIVIDER_SHIFT 12 + +#define PSB_LANE0 0x120 +#define PSB_LANE1 0x220 +#define PSB_LANE2 0x2320 +#define PSB_LANE3 0x2420 + +#define LANE_PLL_MASK (0x7 << 20) +#define LANE_PLL_ENABLE (0x3 << 20) +#define LANE_PLL_PIPE(p) (((p) == 0) ? (1 << 21) : (0 << 21)) + +#define DP_B 0x64100 +#define DP_C 0x64200 + +#define DP_PORT_EN (1 << 31) +#define DP_PIPEB_SELECT (1 << 30) +#define DP_PIPE_MASK (1 << 30) + +/* Link training mode - select a suitable mode for each stage */ +#define DP_LINK_TRAIN_PAT_1 (0 << 28) +#define DP_LINK_TRAIN_PAT_2 (1 << 28) +#define DP_LINK_TRAIN_PAT_IDLE (2 << 28) +#define DP_LINK_TRAIN_OFF (3 << 28) +#define DP_LINK_TRAIN_MASK (3 << 28) +#define DP_LINK_TRAIN_SHIFT 28 + +/* Signal voltages. These are mostly controlled by the other end */ +#define DP_VOLTAGE_0_4 (0 << 25) +#define DP_VOLTAGE_0_6 (1 << 25) +#define DP_VOLTAGE_0_8 (2 << 25) +#define DP_VOLTAGE_1_2 (3 << 25) +#define DP_VOLTAGE_MASK (7 << 25) +#define DP_VOLTAGE_SHIFT 25 + +/* Signal pre-emphasis levels, like voltages, the other end tells us what + * they want + */ +#define DP_PRE_EMPHASIS_0 (0 << 22) +#define DP_PRE_EMPHASIS_3_5 (1 << 22) +#define DP_PRE_EMPHASIS_6 (2 << 22) +#define DP_PRE_EMPHASIS_9_5 (3 << 22) +#define DP_PRE_EMPHASIS_MASK (7 << 22) +#define DP_PRE_EMPHASIS_SHIFT 22 + +/* How many wires to use. I guess 3 was too hard */ +#define DP_PORT_WIDTH_1 (0 << 19) +#define DP_PORT_WIDTH_2 (1 << 19) +#define DP_PORT_WIDTH_4 (3 << 19) +#define DP_PORT_WIDTH_MASK (7 << 19) + +/* Mystic DPCD version 1.1 special mode */ +#define DP_ENHANCED_FRAMING (1 << 18) + +/** locked once port is enabled */ +#define DP_PORT_REVERSAL (1 << 15) + +/** sends the clock on lane 15 of the PEG for debug */ +#define DP_CLOCK_OUTPUT_ENABLE (1 << 13) + +#define DP_SCRAMBLING_DISABLE (1 << 12) +#define DP_SCRAMBLING_DISABLE_IRONLAKE (1 << 7) + +/** limit RGB values to avoid confusing TVs */ +#define DP_COLOR_RANGE_16_235 (1 << 8) + +/** Turn on the audio link */ +#define DP_AUDIO_OUTPUT_ENABLE (1 << 6) + +/** vs and hs sync polarity */ +#define DP_SYNC_VS_HIGH (1 << 4) +#define DP_SYNC_HS_HIGH (1 << 3) + +/** A fantasy */ +#define DP_DETECTED (1 << 2) + +/** The aux channel provides a way to talk to the + * signal sink for DDC etc. Max packet size supported + * is 20 bytes in each direction, hence the 5 fixed + * data registers + */ +#define DPB_AUX_CH_CTL 0x64110 +#define DPB_AUX_CH_DATA1 0x64114 +#define DPB_AUX_CH_DATA2 0x64118 +#define DPB_AUX_CH_DATA3 0x6411c +#define DPB_AUX_CH_DATA4 0x64120 +#define DPB_AUX_CH_DATA5 0x64124 + +#define DPC_AUX_CH_CTL 0x64210 +#define DPC_AUX_CH_DATA1 0x64214 +#define DPC_AUX_CH_DATA2 0x64218 +#define DPC_AUX_CH_DATA3 0x6421c +#define DPC_AUX_CH_DATA4 0x64220 +#define DPC_AUX_CH_DATA5 0x64224 + +#define DP_AUX_CH_CTL_SEND_BUSY (1 << 31) +#define DP_AUX_CH_CTL_DONE (1 << 30) +#define DP_AUX_CH_CTL_INTERRUPT (1 << 29) +#define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28) +#define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26) +#define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26) +#define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26) +#define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26) +#define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26) +#define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25) +#define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20) +#define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20 +#define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16) +#define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16 +#define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15) +#define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14) +#define DP_AUX_CH_CTL_SYNC_TEST (1 << 13) +#define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12) +#define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11) +#define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff) +#define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0 + +/* + * Computing GMCH M and N values for the Display Port link + * + * GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes + * + * ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz) + * + * The GMCH value is used internally + * + * bytes_per_pixel is the number of bytes coming out of the plane, + * which is after the LUTs, so we want the bytes for our color format. + * For our current usage, this is always 3, one byte for R, G and B. + */ + +#define _PIPEA_GMCH_DATA_M 0x70050 +#define _PIPEB_GMCH_DATA_M 0x71050 + +/* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */ +#define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25) +#define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25 + +#define PIPE_GMCH_DATA_M_MASK (0xffffff) + +#define _PIPEA_GMCH_DATA_N 0x70054 +#define _PIPEB_GMCH_DATA_N 0x71054 +#define PIPE_GMCH_DATA_N_MASK (0xffffff) + +/* + * Computing Link M and N values for the Display Port link + * + * Link M / N = pixel_clock / ls_clk + * + * (the DP spec calls pixel_clock the 'strm_clk') + * + * The Link value is transmitted in the Main Stream + * Attributes and VB-ID. + */ + +#define _PIPEA_DP_LINK_M 0x70060 +#define _PIPEB_DP_LINK_M 0x71060 +#define PIPEA_DP_LINK_M_MASK (0xffffff) + +#define _PIPEA_DP_LINK_N 0x70064 +#define _PIPEB_DP_LINK_N 0x71064 +#define PIPEA_DP_LINK_N_MASK (0xffffff) + +#define PIPE_GMCH_DATA_M(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_M, _PIPEB_GMCH_DATA_M) +#define PIPE_GMCH_DATA_N(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_N, _PIPEB_GMCH_DATA_N) +#define PIPE_DP_LINK_M(pipe) _PIPE(pipe, _PIPEA_DP_LINK_M, _PIPEB_DP_LINK_M) +#define PIPE_DP_LINK_N(pipe) _PIPE(pipe, _PIPEA_DP_LINK_N, _PIPEB_DP_LINK_N) + +#define PIPE_BPC_MASK (7 << 5) +#define PIPE_8BPC (0 << 5) +#define PIPE_10BPC (1 << 5) +#define PIPE_6BPC (2 << 5) + +#endif -- cgit v1.2.3-54-g00ecf