From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: AndrĂ© Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- drivers/net/ethernet/freescale/fsl_pq_mdio.c | 499 +++++++++++++++++++++++++++ 1 file changed, 499 insertions(+) create mode 100644 drivers/net/ethernet/freescale/fsl_pq_mdio.c (limited to 'drivers/net/ethernet/freescale/fsl_pq_mdio.c') diff --git a/drivers/net/ethernet/freescale/fsl_pq_mdio.c b/drivers/net/ethernet/freescale/fsl_pq_mdio.c new file mode 100644 index 000000000..3c40f6b99 --- /dev/null +++ b/drivers/net/ethernet/freescale/fsl_pq_mdio.c @@ -0,0 +1,499 @@ +/* + * Freescale PowerQUICC Ethernet Driver -- MIIM bus implementation + * Provides Bus interface for MIIM regs + * + * Author: Andy Fleming + * Modifier: Sandeep Gopalpet + * + * Copyright 2002-2004, 2008-2009 Freescale Semiconductor, Inc. + * + * Based on gianfar_mii.c and ucc_geth_mii.c (Li Yang, Kim Phillips) + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#if IS_ENABLED(CONFIG_UCC_GETH) +#include /* for ucc_set_qe_mux_mii_mng() */ +#endif + +#include "gianfar.h" + +#define MIIMIND_BUSY 0x00000001 +#define MIIMIND_NOTVALID 0x00000004 +#define MIIMCFG_INIT_VALUE 0x00000007 +#define MIIMCFG_RESET 0x80000000 + +#define MII_READ_COMMAND 0x00000001 + +struct fsl_pq_mii { + u32 miimcfg; /* MII management configuration reg */ + u32 miimcom; /* MII management command reg */ + u32 miimadd; /* MII management address reg */ + u32 miimcon; /* MII management control reg */ + u32 miimstat; /* MII management status reg */ + u32 miimind; /* MII management indication reg */ +}; + +struct fsl_pq_mdio { + u8 res1[16]; + u32 ieventm; /* MDIO Interrupt event register (for etsec2)*/ + u32 imaskm; /* MDIO Interrupt mask register (for etsec2)*/ + u8 res2[4]; + u32 emapm; /* MDIO Event mapping register (for etsec2)*/ + u8 res3[1280]; + struct fsl_pq_mii mii; + u8 res4[28]; + u32 utbipar; /* TBI phy address reg (only on UCC) */ + u8 res5[2728]; +} __packed; + +/* Number of microseconds to wait for an MII register to respond */ +#define MII_TIMEOUT 1000 + +struct fsl_pq_mdio_priv { + void __iomem *map; + struct fsl_pq_mii __iomem *regs; + int irqs[PHY_MAX_ADDR]; +}; + +/* + * Per-device-type data. Each type of device tree node that we support gets + * one of these. + * + * @mii_offset: the offset of the MII registers within the memory map of the + * node. Some nodes define only the MII registers, and some define the whole + * MAC (which includes the MII registers). + * + * @get_tbipa: determines the address of the TBIPA register + * + * @ucc_configure: a special function for extra QE configuration + */ +struct fsl_pq_mdio_data { + unsigned int mii_offset; /* offset of the MII registers */ + uint32_t __iomem * (*get_tbipa)(void __iomem *p); + void (*ucc_configure)(phys_addr_t start, phys_addr_t end); +}; + +/* + * Write value to the PHY at mii_id at register regnum, on the bus attached + * to the local interface, which may be different from the generic mdio bus + * (tied to a single interface), waiting until the write is done before + * returning. This is helpful in programming interfaces like the TBI which + * control interfaces like onchip SERDES and are always tied to the local + * mdio pins, which may not be the same as system mdio bus, used for + * controlling the external PHYs, for example. + */ +static int fsl_pq_mdio_write(struct mii_bus *bus, int mii_id, int regnum, + u16 value) +{ + struct fsl_pq_mdio_priv *priv = bus->priv; + struct fsl_pq_mii __iomem *regs = priv->regs; + unsigned int timeout; + + /* Set the PHY address and the register address we want to write */ + iowrite32be((mii_id << 8) | regnum, ®s->miimadd); + + /* Write out the value we want */ + iowrite32be(value, ®s->miimcon); + + /* Wait for the transaction to finish */ + timeout = MII_TIMEOUT; + while ((ioread32be(®s->miimind) & MIIMIND_BUSY) && timeout) { + cpu_relax(); + timeout--; + } + + return timeout ? 0 : -ETIMEDOUT; +} + +/* + * Read the bus for PHY at addr mii_id, register regnum, and return the value. + * Clears miimcom first. + * + * All PHY operation done on the bus attached to the local interface, which + * may be different from the generic mdio bus. This is helpful in programming + * interfaces like the TBI which, in turn, control interfaces like on-chip + * SERDES and are always tied to the local mdio pins, which may not be the + * same as system mdio bus, used for controlling the external PHYs, for eg. + */ +static int fsl_pq_mdio_read(struct mii_bus *bus, int mii_id, int regnum) +{ + struct fsl_pq_mdio_priv *priv = bus->priv; + struct fsl_pq_mii __iomem *regs = priv->regs; + unsigned int timeout; + u16 value; + + /* Set the PHY address and the register address we want to read */ + iowrite32be((mii_id << 8) | regnum, ®s->miimadd); + + /* Clear miimcom, and then initiate a read */ + iowrite32be(0, ®s->miimcom); + iowrite32be(MII_READ_COMMAND, ®s->miimcom); + + /* Wait for the transaction to finish, normally less than 100us */ + timeout = MII_TIMEOUT; + while ((ioread32be(®s->miimind) & + (MIIMIND_NOTVALID | MIIMIND_BUSY)) && timeout) { + cpu_relax(); + timeout--; + } + + if (!timeout) + return -ETIMEDOUT; + + /* Grab the value of the register from miimstat */ + value = ioread32be(®s->miimstat); + + dev_dbg(&bus->dev, "read %04x from address %x/%x\n", value, mii_id, regnum); + return value; +} + +/* Reset the MIIM registers, and wait for the bus to free */ +static int fsl_pq_mdio_reset(struct mii_bus *bus) +{ + struct fsl_pq_mdio_priv *priv = bus->priv; + struct fsl_pq_mii __iomem *regs = priv->regs; + unsigned int timeout; + + mutex_lock(&bus->mdio_lock); + + /* Reset the management interface */ + iowrite32be(MIIMCFG_RESET, ®s->miimcfg); + + /* Setup the MII Mgmt clock speed */ + iowrite32be(MIIMCFG_INIT_VALUE, ®s->miimcfg); + + /* Wait until the bus is free */ + timeout = MII_TIMEOUT; + while ((ioread32be(®s->miimind) & MIIMIND_BUSY) && timeout) { + cpu_relax(); + timeout--; + } + + mutex_unlock(&bus->mdio_lock); + + if (!timeout) { + dev_err(&bus->dev, "timeout waiting for MII bus\n"); + return -EBUSY; + } + + return 0; +} + +#if defined(CONFIG_GIANFAR) || defined(CONFIG_GIANFAR_MODULE) +/* + * This is mildly evil, but so is our hardware for doing this. + * Also, we have to cast back to struct gfar because of + * definition weirdness done in gianfar.h. + */ +static uint32_t __iomem *get_gfar_tbipa(void __iomem *p) +{ + struct gfar __iomem *enet_regs = p; + + return &enet_regs->tbipa; +} + +/* + * Return the TBIPAR address for an eTSEC2 node + */ +static uint32_t __iomem *get_etsec_tbipa(void __iomem *p) +{ + return p; +} +#endif + +#if defined(CONFIG_UCC_GETH) || defined(CONFIG_UCC_GETH_MODULE) +/* + * Return the TBIPAR address for a QE MDIO node + */ +static uint32_t __iomem *get_ucc_tbipa(void __iomem *p) +{ + struct fsl_pq_mdio __iomem *mdio = p; + + return &mdio->utbipar; +} + +/* + * Find the UCC node that controls the given MDIO node + * + * For some reason, the QE MDIO nodes are not children of the UCC devices + * that control them. Therefore, we need to scan all UCC nodes looking for + * the one that encompases the given MDIO node. We do this by comparing + * physical addresses. The 'start' and 'end' addresses of the MDIO node are + * passed, and the correct UCC node will cover the entire address range. + * + * This assumes that there is only one QE MDIO node in the entire device tree. + */ +static void ucc_configure(phys_addr_t start, phys_addr_t end) +{ + static bool found_mii_master; + struct device_node *np = NULL; + + if (found_mii_master) + return; + + for_each_compatible_node(np, NULL, "ucc_geth") { + struct resource res; + const uint32_t *iprop; + uint32_t id; + int ret; + + ret = of_address_to_resource(np, 0, &res); + if (ret < 0) { + pr_debug("fsl-pq-mdio: no address range in node %s\n", + np->full_name); + continue; + } + + /* if our mdio regs fall within this UCC regs range */ + if ((start < res.start) || (end > res.end)) + continue; + + iprop = of_get_property(np, "cell-index", NULL); + if (!iprop) { + iprop = of_get_property(np, "device-id", NULL); + if (!iprop) { + pr_debug("fsl-pq-mdio: no UCC ID in node %s\n", + np->full_name); + continue; + } + } + + id = be32_to_cpup(iprop); + + /* + * cell-index and device-id for QE nodes are + * numbered from 1, not 0. + */ + if (ucc_set_qe_mux_mii_mng(id - 1) < 0) { + pr_debug("fsl-pq-mdio: invalid UCC ID in node %s\n", + np->full_name); + continue; + } + + pr_debug("fsl-pq-mdio: setting node UCC%u to MII master\n", id); + found_mii_master = true; + } +} + +#endif + +static const struct of_device_id fsl_pq_mdio_match[] = { +#if defined(CONFIG_GIANFAR) || defined(CONFIG_GIANFAR_MODULE) + { + .compatible = "fsl,gianfar-tbi", + .data = &(struct fsl_pq_mdio_data) { + .mii_offset = 0, + .get_tbipa = get_gfar_tbipa, + }, + }, + { + .compatible = "fsl,gianfar-mdio", + .data = &(struct fsl_pq_mdio_data) { + .mii_offset = 0, + .get_tbipa = get_gfar_tbipa, + }, + }, + { + .type = "mdio", + .compatible = "gianfar", + .data = &(struct fsl_pq_mdio_data) { + .mii_offset = offsetof(struct fsl_pq_mdio, mii), + .get_tbipa = get_gfar_tbipa, + }, + }, + { + .compatible = "fsl,etsec2-tbi", + .data = &(struct fsl_pq_mdio_data) { + .mii_offset = offsetof(struct fsl_pq_mdio, mii), + .get_tbipa = get_etsec_tbipa, + }, + }, + { + .compatible = "fsl,etsec2-mdio", + .data = &(struct fsl_pq_mdio_data) { + .mii_offset = offsetof(struct fsl_pq_mdio, mii), + .get_tbipa = get_etsec_tbipa, + }, + }, +#endif +#if defined(CONFIG_UCC_GETH) || defined(CONFIG_UCC_GETH_MODULE) + { + .compatible = "fsl,ucc-mdio", + .data = &(struct fsl_pq_mdio_data) { + .mii_offset = 0, + .get_tbipa = get_ucc_tbipa, + .ucc_configure = ucc_configure, + }, + }, + { + /* Legacy UCC MDIO node */ + .type = "mdio", + .compatible = "ucc_geth_phy", + .data = &(struct fsl_pq_mdio_data) { + .mii_offset = 0, + .get_tbipa = get_ucc_tbipa, + .ucc_configure = ucc_configure, + }, + }, +#endif + /* No Kconfig option for Fman support yet */ + { + .compatible = "fsl,fman-mdio", + .data = &(struct fsl_pq_mdio_data) { + .mii_offset = 0, + /* Fman TBI operations are handled elsewhere */ + }, + }, + + {}, +}; +MODULE_DEVICE_TABLE(of, fsl_pq_mdio_match); + +static int fsl_pq_mdio_probe(struct platform_device *pdev) +{ + const struct of_device_id *id = + of_match_device(fsl_pq_mdio_match, &pdev->dev); + const struct fsl_pq_mdio_data *data = id->data; + struct device_node *np = pdev->dev.of_node; + struct resource res; + struct device_node *tbi; + struct fsl_pq_mdio_priv *priv; + struct mii_bus *new_bus; + int err; + + dev_dbg(&pdev->dev, "found %s compatible node\n", id->compatible); + + new_bus = mdiobus_alloc_size(sizeof(*priv)); + if (!new_bus) + return -ENOMEM; + + priv = new_bus->priv; + new_bus->name = "Freescale PowerQUICC MII Bus", + new_bus->read = &fsl_pq_mdio_read; + new_bus->write = &fsl_pq_mdio_write; + new_bus->reset = &fsl_pq_mdio_reset; + new_bus->irq = priv->irqs; + + err = of_address_to_resource(np, 0, &res); + if (err < 0) { + dev_err(&pdev->dev, "could not obtain address information\n"); + goto error; + } + + snprintf(new_bus->id, MII_BUS_ID_SIZE, "%s@%llx", np->name, + (unsigned long long)res.start); + + priv->map = of_iomap(np, 0); + if (!priv->map) { + err = -ENOMEM; + goto error; + } + + /* + * Some device tree nodes represent only the MII registers, and + * others represent the MAC and MII registers. The 'mii_offset' field + * contains the offset of the MII registers inside the mapped register + * space. + */ + if (data->mii_offset > resource_size(&res)) { + dev_err(&pdev->dev, "invalid register map\n"); + err = -EINVAL; + goto error; + } + priv->regs = priv->map + data->mii_offset; + + new_bus->parent = &pdev->dev; + platform_set_drvdata(pdev, new_bus); + + if (data->get_tbipa) { + for_each_child_of_node(np, tbi) { + if (strcmp(tbi->type, "tbi-phy") == 0) { + dev_dbg(&pdev->dev, "found TBI PHY node %s\n", + strrchr(tbi->full_name, '/') + 1); + break; + } + } + + if (tbi) { + const u32 *prop = of_get_property(tbi, "reg", NULL); + uint32_t __iomem *tbipa; + + if (!prop) { + dev_err(&pdev->dev, + "missing 'reg' property in node %s\n", + tbi->full_name); + err = -EBUSY; + goto error; + } + + tbipa = data->get_tbipa(priv->map); + + iowrite32be(be32_to_cpup(prop), tbipa); + } + } + + if (data->ucc_configure) + data->ucc_configure(res.start, res.end); + + err = of_mdiobus_register(new_bus, np); + if (err) { + dev_err(&pdev->dev, "cannot register %s as MDIO bus\n", + new_bus->name); + goto error; + } + + return 0; + +error: + if (priv->map) + iounmap(priv->map); + + kfree(new_bus); + + return err; +} + + +static int fsl_pq_mdio_remove(struct platform_device *pdev) +{ + struct device *device = &pdev->dev; + struct mii_bus *bus = dev_get_drvdata(device); + struct fsl_pq_mdio_priv *priv = bus->priv; + + mdiobus_unregister(bus); + + iounmap(priv->map); + mdiobus_free(bus); + + return 0; +} + +static struct platform_driver fsl_pq_mdio_driver = { + .driver = { + .name = "fsl-pq_mdio", + .of_match_table = fsl_pq_mdio_match, + }, + .probe = fsl_pq_mdio_probe, + .remove = fsl_pq_mdio_remove, +}; + +module_platform_driver(fsl_pq_mdio_driver); + +MODULE_LICENSE("GPL"); -- cgit v1.2.3-54-g00ecf