From 8d91c1e411f55d7ea91b1183a2e9f8088fb4d5be Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Tue, 15 Dec 2015 14:52:16 -0300 Subject: Linux-libre 4.3.2-gnu --- drivers/tty/serial/8250/8250.h | 17 +- drivers/tty/serial/8250/8250_core.c | 3270 ++------------------------------ drivers/tty/serial/8250/8250_dma.c | 4 - drivers/tty/serial/8250/8250_dw.c | 27 +- drivers/tty/serial/8250/8250_early.c | 4 +- drivers/tty/serial/8250/8250_fintek.c | 172 +- drivers/tty/serial/8250/8250_ingenic.c | 1 - drivers/tty/serial/8250/8250_omap.c | 133 +- drivers/tty/serial/8250/8250_pci.c | 82 + drivers/tty/serial/8250/8250_port.c | 2922 ++++++++++++++++++++++++++++ drivers/tty/serial/8250/Makefile | 5 +- drivers/tty/serial/Kconfig | 6 +- drivers/tty/serial/atmel_serial.c | 484 +++-- drivers/tty/serial/etraxfs-uart.c | 59 +- drivers/tty/serial/imx.c | 183 +- drivers/tty/serial/lantiq.c | 8 +- drivers/tty/serial/men_z135_uart.c | 1 - drivers/tty/serial/mpc52xx_uart.c | 5 +- drivers/tty/serial/mxs-auart.c | 58 +- drivers/tty/serial/samsung.c | 1 - drivers/tty/serial/sc16is7xx.c | 113 +- drivers/tty/serial/serial_core.c | 25 +- drivers/tty/serial/sirfsoc_uart.c | 126 +- drivers/tty/serial/sirfsoc_uart.h | 5 +- drivers/tty/serial/sn_console.c | 32 +- drivers/tty/serial/stm32-usart.c | 2 +- drivers/tty/serial/suncore.c | 11 +- drivers/tty/serial/sunhv.c | 13 +- drivers/tty/serial/ucc_uart.c | 2 +- 29 files changed, 4139 insertions(+), 3632 deletions(-) create mode 100644 drivers/tty/serial/8250/8250_port.c (limited to 'drivers/tty/serial') diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h index c43f74c53..d54dcd87c 100644 --- a/drivers/tty/serial/8250/8250.h +++ b/drivers/tty/serial/8250/8250.h @@ -42,9 +42,9 @@ struct uart_8250_dma { size_t rx_size; size_t tx_size; - unsigned char tx_running:1; - unsigned char tx_err: 1; - unsigned char rx_running:1; + unsigned char tx_running; + unsigned char tx_err; + unsigned char rx_running; }; struct old_serial_port { @@ -211,3 +211,14 @@ static inline int ns16550a_goto_highspeed(struct uart_8250_port *up) } return 1; } + +static inline int serial_index(struct uart_port *port) +{ + return port->minor - 64; +} + +#if 0 +#define DEBUG_INTR(fmt...) printk(fmt) +#else +#define DEBUG_INTR(fmt...) do { } while (0) +#endif diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index a3a83164b..d4adaf380 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -1,25 +1,23 @@ /* - * Driver for 8250/16550-type serial ports + * Universal/legacy driver for 8250/16550-type serial ports * * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. * * Copyright (C) 2001 Russell King. * + * Supports: ISA-compatible 8250/16550 ports + * PNP 8250/16550 ports + * early_serial_setup() ports + * userspace-configurable "phantom" ports + * "serial8250" platform devices + * serial8250_register_8250_port() ports + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. - * - * A note about mapbase / membase - * - * mapbase is the physical address of the IO port. - * membase is an 'ioremapped' cookie. */ -#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) -#define SUPPORT_SYSRQ -#endif - #include #include #include @@ -38,11 +36,11 @@ #include #include #include +#include #ifdef CONFIG_SPARC #include #endif -#include #include #include "8250.h" @@ -58,33 +56,10 @@ static unsigned int nr_uarts = CONFIG_SERIAL_8250_RUNTIME_UARTS; static struct uart_driver serial8250_reg; -static int serial_index(struct uart_port *port) -{ - return port->minor - 64; -} - static unsigned int skip_txen_test; /* force skip of txen test at init time */ -/* - * Debugging. - */ -#if 0 -#define DEBUG_AUTOCONF(fmt...) printk(fmt) -#else -#define DEBUG_AUTOCONF(fmt...) do { } while (0) -#endif - -#if 0 -#define DEBUG_INTR(fmt...) printk(fmt) -#else -#define DEBUG_INTR(fmt...) do { } while (0) -#endif - #define PASS_LIMIT 512 -#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) - - #include /* * SERIAL_PORT_DFNS tells us about built-in ports that have no @@ -120,2703 +95,268 @@ static struct hlist_head irq_lists[NR_IRQ_HASH]; static DEFINE_MUTEX(hash_mutex); /* Used to walk the hash */ /* - * Here we define the default xmit fifo size used for each type of UART. + * This is the serial driver's interrupt routine. + * + * Arjan thinks the old way was overly complex, so it got simplified. + * Alan disagrees, saying that need the complexity to handle the weird + * nature of ISA shared interrupts. (This is a special exception.) + * + * In order to handle ISA shared interrupts properly, we need to check + * that all ports have been serviced, and therefore the ISA interrupt + * line has been de-asserted. + * + * This means we need to loop through all ports. checking that they + * don't have an interrupt pending. */ -static const struct serial8250_config uart_config[] = { - [PORT_UNKNOWN] = { - .name = "unknown", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_8250] = { - .name = "8250", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16450] = { - .name = "16450", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16550] = { - .name = "16550", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16550A] = { - .name = "16550A", - .fifo_size = 16, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .rxtrig_bytes = {1, 4, 8, 14}, - .flags = UART_CAP_FIFO, - }, - [PORT_CIRRUS] = { - .name = "Cirrus", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16650] = { - .name = "ST16650", - .fifo_size = 1, - .tx_loadsz = 1, - .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, - }, - [PORT_16650V2] = { - .name = "ST16650V2", - .fifo_size = 32, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | - UART_FCR_T_TRIG_00, - .rxtrig_bytes = {8, 16, 24, 28}, - .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, - }, - [PORT_16750] = { - .name = "TI16750", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | - UART_FCR7_64BYTE, - .rxtrig_bytes = {1, 16, 32, 56}, - .flags = UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE, - }, - [PORT_STARTECH] = { - .name = "Startech", - .fifo_size = 1, - .tx_loadsz = 1, - }, - [PORT_16C950] = { - .name = "16C950/954", - .fifo_size = 128, - .tx_loadsz = 128, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - /* UART_CAP_EFR breaks billionon CF bluetooth card. */ - .flags = UART_CAP_FIFO | UART_CAP_SLEEP, - }, - [PORT_16654] = { - .name = "ST16654", - .fifo_size = 64, - .tx_loadsz = 32, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | - UART_FCR_T_TRIG_10, - .rxtrig_bytes = {8, 16, 56, 60}, - .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, - }, - [PORT_16850] = { - .name = "XR16850", - .fifo_size = 128, - .tx_loadsz = 128, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, - }, - [PORT_RSA] = { - .name = "RSA", - .fifo_size = 2048, - .tx_loadsz = 2048, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11, - .flags = UART_CAP_FIFO, - }, - [PORT_NS16550A] = { - .name = "NS16550A", - .fifo_size = 16, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_NATSEMI, - }, - [PORT_XSCALE] = { - .name = "XScale", - .fifo_size = 32, - .tx_loadsz = 32, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE, - }, - [PORT_OCTEON] = { - .name = "OCTEON", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO, - }, - [PORT_AR7] = { - .name = "AR7", - .fifo_size = 16, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, - [PORT_U6_16550A] = { - .name = "U6_16550A", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, - [PORT_TEGRA] = { - .name = "Tegra", - .fifo_size = 32, - .tx_loadsz = 8, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | - UART_FCR_T_TRIG_01, - .rxtrig_bytes = {1, 4, 8, 14}, - .flags = UART_CAP_FIFO | UART_CAP_RTOIE, - }, - [PORT_XR17D15X] = { - .name = "XR17D15X", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | - UART_CAP_SLEEP, - }, - [PORT_XR17V35X] = { - .name = "XR17V35X", - .fifo_size = 256, - .tx_loadsz = 256, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 | - UART_FCR_T_TRIG_11, - .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | - UART_CAP_SLEEP, - }, - [PORT_LPC3220] = { - .name = "LPC3220", - .fifo_size = 64, - .tx_loadsz = 32, - .fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO | - UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00, - .flags = UART_CAP_FIFO, - }, - [PORT_BRCM_TRUMANAGE] = { - .name = "TruManage", - .fifo_size = 1, - .tx_loadsz = 1024, - .flags = UART_CAP_HFIFO, - }, - [PORT_8250_CIR] = { - .name = "CIR port" - }, - [PORT_ALTR_16550_F32] = { - .name = "Altera 16550 FIFO32", - .fifo_size = 32, - .tx_loadsz = 32, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, - [PORT_ALTR_16550_F64] = { - .name = "Altera 16550 FIFO64", - .fifo_size = 64, - .tx_loadsz = 64, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, - [PORT_ALTR_16550_F128] = { - .name = "Altera 16550 FIFO128", - .fifo_size = 128, - .tx_loadsz = 128, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO | UART_CAP_AFE, - }, -/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement -workaround of errata A-008006 which states that tx_loadsz should be -configured less than Maximum supported fifo bytes */ - [PORT_16550A_FSL64] = { - .name = "16550A_FSL64", - .fifo_size = 64, - .tx_loadsz = 63, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | - UART_FCR7_64BYTE, - .flags = UART_CAP_FIFO, - }, - [PORT_RT2880] = { - .name = "Palmchip BK-3103", - .fifo_size = 16, - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .rxtrig_bytes = {1, 4, 8, 14}, - .flags = UART_CAP_FIFO, - }, -}; - -/* Uart divisor latch read */ -static int default_serial_dl_read(struct uart_8250_port *up) -{ - return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8; -} - -/* Uart divisor latch write */ -static void default_serial_dl_write(struct uart_8250_port *up, int value) -{ - serial_out(up, UART_DLL, value & 0xff); - serial_out(up, UART_DLM, value >> 8 & 0xff); -} - -#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) - -/* Au1x00/RT288x UART hardware has a weird register layout */ -static const s8 au_io_in_map[8] = { - 0, /* UART_RX */ - 2, /* UART_IER */ - 3, /* UART_IIR */ - 5, /* UART_LCR */ - 6, /* UART_MCR */ - 7, /* UART_LSR */ - 8, /* UART_MSR */ - -1, /* UART_SCR (unmapped) */ -}; - -static const s8 au_io_out_map[8] = { - 1, /* UART_TX */ - 2, /* UART_IER */ - 4, /* UART_FCR */ - 5, /* UART_LCR */ - 6, /* UART_MCR */ - -1, /* UART_LSR (unmapped) */ - -1, /* UART_MSR (unmapped) */ - -1, /* UART_SCR (unmapped) */ -}; - -static unsigned int au_serial_in(struct uart_port *p, int offset) -{ - if (offset >= ARRAY_SIZE(au_io_in_map)) - return UINT_MAX; - offset = au_io_in_map[offset]; - if (offset < 0) - return UINT_MAX; - return __raw_readl(p->membase + (offset << p->regshift)); -} - -static void au_serial_out(struct uart_port *p, int offset, int value) -{ - if (offset >= ARRAY_SIZE(au_io_out_map)) - return; - offset = au_io_out_map[offset]; - if (offset < 0) - return; - __raw_writel(value, p->membase + (offset << p->regshift)); -} - -/* Au1x00 haven't got a standard divisor latch */ -static int au_serial_dl_read(struct uart_8250_port *up) +static irqreturn_t serial8250_interrupt(int irq, void *dev_id) { - return __raw_readl(up->port.membase + 0x28); -} + struct irq_info *i = dev_id; + struct list_head *l, *end = NULL; + int pass_counter = 0, handled = 0; -static void au_serial_dl_write(struct uart_8250_port *up, int value) -{ - __raw_writel(value, up->port.membase + 0x28); -} + DEBUG_INTR("serial8250_interrupt(%d)...", irq); -#endif + spin_lock(&i->lock); -static unsigned int hub6_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - outb(p->hub6 - 1 + offset, p->iobase); - return inb(p->iobase + 1); -} + l = i->head; + do { + struct uart_8250_port *up; + struct uart_port *port; -static void hub6_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - outb(p->hub6 - 1 + offset, p->iobase); - outb(value, p->iobase + 1); -} + up = list_entry(l, struct uart_8250_port, list); + port = &up->port; -static unsigned int mem_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - return readb(p->membase + offset); -} + if (port->handle_irq(port)) { + handled = 1; + end = NULL; + } else if (end == NULL) + end = l; -static void mem_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - writeb(value, p->membase + offset); -} + l = l->next; -static void mem32_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - writel(value, p->membase + offset); -} + if (l == i->head && pass_counter++ > PASS_LIMIT) { + /* If we hit this, we're dead. */ + printk_ratelimited(KERN_ERR + "serial8250: too much work for irq%d\n", irq); + break; + } + } while (l != end); -static unsigned int mem32_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - return readl(p->membase + offset); -} + spin_unlock(&i->lock); -static void mem32be_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - iowrite32be(value, p->membase + offset); -} + DEBUG_INTR("end.\n"); -static unsigned int mem32be_serial_in(struct uart_port *p, int offset) -{ - offset = offset << p->regshift; - return ioread32be(p->membase + offset); + return IRQ_RETVAL(handled); } -static unsigned int io_serial_in(struct uart_port *p, int offset) +/* + * To support ISA shared interrupts, we need to have one interrupt + * handler that ensures that the IRQ line has been deasserted + * before returning. Failing to do this will result in the IRQ + * line being stuck active, and, since ISA irqs are edge triggered, + * no more IRQs will be seen. + */ +static void serial_do_unlink(struct irq_info *i, struct uart_8250_port *up) { - offset = offset << p->regshift; - return inb(p->iobase + offset); -} + spin_lock_irq(&i->lock); -static void io_serial_out(struct uart_port *p, int offset, int value) -{ - offset = offset << p->regshift; - outb(value, p->iobase + offset); + if (!list_empty(i->head)) { + if (i->head == &up->list) + i->head = i->head->next; + list_del(&up->list); + } else { + BUG_ON(i->head != &up->list); + i->head = NULL; + } + spin_unlock_irq(&i->lock); + /* List empty so throw away the hash node */ + if (i->head == NULL) { + hlist_del(&i->node); + kfree(i); + } } -static int serial8250_default_handle_irq(struct uart_port *port); -static int exar_handle_irq(struct uart_port *port); - -static void set_io_from_upio(struct uart_port *p) +static int serial_link_irq_chain(struct uart_8250_port *up) { - struct uart_8250_port *up = up_to_u8250p(p); - - up->dl_read = default_serial_dl_read; - up->dl_write = default_serial_dl_write; + struct hlist_head *h; + struct hlist_node *n; + struct irq_info *i; + int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; - switch (p->iotype) { - case UPIO_HUB6: - p->serial_in = hub6_serial_in; - p->serial_out = hub6_serial_out; - break; + mutex_lock(&hash_mutex); - case UPIO_MEM: - p->serial_in = mem_serial_in; - p->serial_out = mem_serial_out; - break; + h = &irq_lists[up->port.irq % NR_IRQ_HASH]; - case UPIO_MEM32: - p->serial_in = mem32_serial_in; - p->serial_out = mem32_serial_out; - break; + hlist_for_each(n, h) { + i = hlist_entry(n, struct irq_info, node); + if (i->irq == up->port.irq) + break; + } - case UPIO_MEM32BE: - p->serial_in = mem32be_serial_in; - p->serial_out = mem32be_serial_out; - break; + if (n == NULL) { + i = kzalloc(sizeof(struct irq_info), GFP_KERNEL); + if (i == NULL) { + mutex_unlock(&hash_mutex); + return -ENOMEM; + } + spin_lock_init(&i->lock); + i->irq = up->port.irq; + hlist_add_head(&i->node, h); + } + mutex_unlock(&hash_mutex); -#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) - case UPIO_AU: - p->serial_in = au_serial_in; - p->serial_out = au_serial_out; - up->dl_read = au_serial_dl_read; - up->dl_write = au_serial_dl_write; - break; -#endif + spin_lock_irq(&i->lock); - default: - p->serial_in = io_serial_in; - p->serial_out = io_serial_out; - break; - } - /* Remember loaded iotype */ - up->cur_iotype = p->iotype; - p->handle_irq = serial8250_default_handle_irq; -} + if (i->head) { + list_add(&up->list, i->head); + spin_unlock_irq(&i->lock); -static void -serial_port_out_sync(struct uart_port *p, int offset, int value) -{ - switch (p->iotype) { - case UPIO_MEM: - case UPIO_MEM32: - case UPIO_MEM32BE: - case UPIO_AU: - p->serial_out(p, offset, value); - p->serial_in(p, UART_LCR); /* safe, no side-effects */ - break; - default: - p->serial_out(p, offset, value); + ret = 0; + } else { + INIT_LIST_HEAD(&up->list); + i->head = &up->list; + spin_unlock_irq(&i->lock); + irq_flags |= up->port.irqflags; + ret = request_irq(up->port.irq, serial8250_interrupt, + irq_flags, "serial", i); + if (ret < 0) + serial_do_unlink(i, up); } -} -/* - * For the 16C950 - */ -static void serial_icr_write(struct uart_8250_port *up, int offset, int value) -{ - serial_out(up, UART_SCR, offset); - serial_out(up, UART_ICR, value); + return ret; } -static unsigned int serial_icr_read(struct uart_8250_port *up, int offset) +static void serial_unlink_irq_chain(struct uart_8250_port *up) { - unsigned int value; + /* + * yes, some broken gcc emit "warning: 'i' may be used uninitialized" + * but no, we are not going to take a patch that assigns NULL below. + */ + struct irq_info *i; + struct hlist_node *n; + struct hlist_head *h; - serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD); - serial_out(up, UART_SCR, offset); - value = serial_in(up, UART_ICR); - serial_icr_write(up, UART_ACR, up->acr); + mutex_lock(&hash_mutex); - return value; -} + h = &irq_lists[up->port.irq % NR_IRQ_HASH]; -/* - * FIFO support. - */ -static void serial8250_clear_fifos(struct uart_8250_port *p) -{ - if (p->capabilities & UART_CAP_FIFO) { - serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO); - serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO | - UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); - serial_out(p, UART_FCR, 0); + hlist_for_each(n, h) { + i = hlist_entry(n, struct irq_info, node); + if (i->irq == up->port.irq) + break; } -} -void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p) -{ - serial8250_clear_fifos(p); - serial_out(p, UART_FCR, p->fcr); -} -EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos); + BUG_ON(n == NULL); + BUG_ON(i->head == NULL); -void serial8250_rpm_get(struct uart_8250_port *p) -{ - if (!(p->capabilities & UART_CAP_RPM)) - return; - pm_runtime_get_sync(p->port.dev); -} -EXPORT_SYMBOL_GPL(serial8250_rpm_get); + if (list_empty(i->head)) + free_irq(up->port.irq, i); -void serial8250_rpm_put(struct uart_8250_port *p) -{ - if (!(p->capabilities & UART_CAP_RPM)) - return; - pm_runtime_mark_last_busy(p->port.dev); - pm_runtime_put_autosuspend(p->port.dev); + serial_do_unlink(i, up); + mutex_unlock(&hash_mutex); } -EXPORT_SYMBOL_GPL(serial8250_rpm_put); /* - * These two wrappers ensure that enable_runtime_pm_tx() can be called more than - * once and disable_runtime_pm_tx() will still disable RPM because the fifo is - * empty and the HW can idle again. + * This function is used to handle ports that do not have an + * interrupt. This doesn't work very well for 16450's, but gives + * barely passable results for a 16550A. (Although at the expense + * of much CPU overhead). */ -static void serial8250_rpm_get_tx(struct uart_8250_port *p) +static void serial8250_timeout(unsigned long data) { - unsigned char rpm_active; - - if (!(p->capabilities & UART_CAP_RPM)) - return; + struct uart_8250_port *up = (struct uart_8250_port *)data; - rpm_active = xchg(&p->rpm_tx_active, 1); - if (rpm_active) - return; - pm_runtime_get_sync(p->port.dev); + up->port.handle_irq(&up->port); + mod_timer(&up->timer, jiffies + uart_poll_timeout(&up->port)); } -static void serial8250_rpm_put_tx(struct uart_8250_port *p) +static void serial8250_backup_timeout(unsigned long data) { - unsigned char rpm_active; + struct uart_8250_port *up = (struct uart_8250_port *)data; + unsigned int iir, ier = 0, lsr; + unsigned long flags; - if (!(p->capabilities & UART_CAP_RPM)) - return; - - rpm_active = xchg(&p->rpm_tx_active, 0); - if (!rpm_active) - return; - pm_runtime_mark_last_busy(p->port.dev); - pm_runtime_put_autosuspend(p->port.dev); -} - -/* - * IER sleep support. UARTs which have EFRs need the "extended - * capability" bit enabled. Note that on XR16C850s, we need to - * reset LCR to write to IER. - */ -static void serial8250_set_sleep(struct uart_8250_port *p, int sleep) -{ - unsigned char lcr = 0, efr = 0; - /* - * Exar UARTs have a SLEEP register that enables or disables - * each UART to enter sleep mode separately. On the XR17V35x the - * register is accessible to each UART at the UART_EXAR_SLEEP - * offset but the UART channel may only write to the corresponding - * bit. - */ - serial8250_rpm_get(p); - if ((p->port.type == PORT_XR17V35X) || - (p->port.type == PORT_XR17D15X)) { - serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0); - goto out; - } - - if (p->capabilities & UART_CAP_SLEEP) { - if (p->capabilities & UART_CAP_EFR) { - lcr = serial_in(p, UART_LCR); - efr = serial_in(p, UART_EFR); - serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(p, UART_EFR, UART_EFR_ECB); - serial_out(p, UART_LCR, 0); - } - serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0); - if (p->capabilities & UART_CAP_EFR) { - serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(p, UART_EFR, efr); - serial_out(p, UART_LCR, lcr); - } - } -out: - serial8250_rpm_put(p); -} - -#ifdef CONFIG_SERIAL_8250_RSA -/* - * Attempts to turn on the RSA FIFO. Returns zero on failure. - * We set the port uart clock rate if we succeed. - */ -static int __enable_rsa(struct uart_8250_port *up) -{ - unsigned char mode; - int result; - - mode = serial_in(up, UART_RSA_MSR); - result = mode & UART_RSA_MSR_FIFO; - - if (!result) { - serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO); - mode = serial_in(up, UART_RSA_MSR); - result = mode & UART_RSA_MSR_FIFO; - } - - if (result) - up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16; - - return result; -} - -static void enable_rsa(struct uart_8250_port *up) -{ - if (up->port.type == PORT_RSA) { - if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) { - spin_lock_irq(&up->port.lock); - __enable_rsa(up); - spin_unlock_irq(&up->port.lock); - } - if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) - serial_out(up, UART_RSA_FRR, 0); - } -} - -/* - * Attempts to turn off the RSA FIFO. Returns zero on failure. - * It is unknown why interrupts were disabled in here. However, - * the caller is expected to preserve this behaviour by grabbing - * the spinlock before calling this function. - */ -static void disable_rsa(struct uart_8250_port *up) -{ - unsigned char mode; - int result; - - if (up->port.type == PORT_RSA && - up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) { - spin_lock_irq(&up->port.lock); - - mode = serial_in(up, UART_RSA_MSR); - result = !(mode & UART_RSA_MSR_FIFO); - - if (!result) { - serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO); - mode = serial_in(up, UART_RSA_MSR); - result = !(mode & UART_RSA_MSR_FIFO); - } - - if (result) - up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16; - spin_unlock_irq(&up->port.lock); - } -} -#endif /* CONFIG_SERIAL_8250_RSA */ - -/* - * This is a quickie test to see how big the FIFO is. - * It doesn't work at all the time, more's the pity. - */ -static int size_fifo(struct uart_8250_port *up) -{ - unsigned char old_fcr, old_mcr, old_lcr; - unsigned short old_dl; - int count; - - old_lcr = serial_in(up, UART_LCR); - serial_out(up, UART_LCR, 0); - old_fcr = serial_in(up, UART_FCR); - old_mcr = serial_in(up, UART_MCR); - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | - UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); - serial_out(up, UART_MCR, UART_MCR_LOOP); - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - old_dl = serial_dl_read(up); - serial_dl_write(up, 0x0001); - serial_out(up, UART_LCR, 0x03); - for (count = 0; count < 256; count++) - serial_out(up, UART_TX, count); - mdelay(20);/* FIXME - schedule_timeout */ - for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) && - (count < 256); count++) - serial_in(up, UART_RX); - serial_out(up, UART_FCR, old_fcr); - serial_out(up, UART_MCR, old_mcr); - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - serial_dl_write(up, old_dl); - serial_out(up, UART_LCR, old_lcr); - - return count; -} - -/* - * Read UART ID using the divisor method - set DLL and DLM to zero - * and the revision will be in DLL and device type in DLM. We - * preserve the device state across this. - */ -static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p) -{ - unsigned char old_dll, old_dlm, old_lcr; - unsigned int id; - - old_lcr = serial_in(p, UART_LCR); - serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A); - - old_dll = serial_in(p, UART_DLL); - old_dlm = serial_in(p, UART_DLM); - - serial_out(p, UART_DLL, 0); - serial_out(p, UART_DLM, 0); - - id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8; - - serial_out(p, UART_DLL, old_dll); - serial_out(p, UART_DLM, old_dlm); - serial_out(p, UART_LCR, old_lcr); - - return id; -} - -/* - * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's. - * When this function is called we know it is at least a StarTech - * 16650 V2, but it might be one of several StarTech UARTs, or one of - * its clones. (We treat the broken original StarTech 16650 V1 as a - * 16550, and why not? Startech doesn't seem to even acknowledge its - * existence.) - * - * What evil have men's minds wrought... - */ -static void autoconfig_has_efr(struct uart_8250_port *up) -{ - unsigned int id1, id2, id3, rev; - - /* - * Everything with an EFR has SLEEP - */ - up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; - - /* - * First we check to see if it's an Oxford Semiconductor UART. - * - * If we have to do this here because some non-National - * Semiconductor clone chips lock up if you try writing to the - * LSR register (which serial_icr_read does) - */ - - /* - * Check for Oxford Semiconductor 16C950. - * - * EFR [4] must be set else this test fails. - * - * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca) - * claims that it's needed for 952 dual UART's (which are not - * recommended for new designs). - */ - up->acr = 0; - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, UART_EFR_ECB); - serial_out(up, UART_LCR, 0x00); - id1 = serial_icr_read(up, UART_ID1); - id2 = serial_icr_read(up, UART_ID2); - id3 = serial_icr_read(up, UART_ID3); - rev = serial_icr_read(up, UART_REV); - - DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev); - - if (id1 == 0x16 && id2 == 0xC9 && - (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) { - up->port.type = PORT_16C950; - - /* - * Enable work around for the Oxford Semiconductor 952 rev B - * chip which causes it to seriously miscalculate baud rates - * when DLL is 0. - */ - if (id3 == 0x52 && rev == 0x01) - up->bugs |= UART_BUG_QUOT; - return; - } - - /* - * We check for a XR16C850 by setting DLL and DLM to 0, and then - * reading back DLL and DLM. The chip type depends on the DLM - * value read back: - * 0x10 - XR16C850 and the DLL contains the chip revision. - * 0x12 - XR16C2850. - * 0x14 - XR16C854. - */ - id1 = autoconfig_read_divisor_id(up); - DEBUG_AUTOCONF("850id=%04x ", id1); - - id2 = id1 >> 8; - if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) { - up->port.type = PORT_16850; - return; - } - - /* - * It wasn't an XR16C850. - * - * We distinguish between the '654 and the '650 by counting - * how many bytes are in the FIFO. I'm using this for now, - * since that's the technique that was sent to me in the - * serial driver update, but I'm not convinced this works. - * I've had problems doing this in the past. -TYT - */ - if (size_fifo(up) == 64) - up->port.type = PORT_16654; - else - up->port.type = PORT_16650V2; -} - -/* - * We detected a chip without a FIFO. Only two fall into - * this category - the original 8250 and the 16450. The - * 16450 has a scratch register (accessible with LCR=0) - */ -static void autoconfig_8250(struct uart_8250_port *up) -{ - unsigned char scratch, status1, status2; - - up->port.type = PORT_8250; - - scratch = serial_in(up, UART_SCR); - serial_out(up, UART_SCR, 0xa5); - status1 = serial_in(up, UART_SCR); - serial_out(up, UART_SCR, 0x5a); - status2 = serial_in(up, UART_SCR); - serial_out(up, UART_SCR, scratch); - - if (status1 == 0xa5 && status2 == 0x5a) - up->port.type = PORT_16450; -} - -static int broken_efr(struct uart_8250_port *up) -{ - /* - * Exar ST16C2550 "A2" devices incorrectly detect as - * having an EFR, and report an ID of 0x0201. See - * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html - */ - if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16) - return 1; - - return 0; -} - -/* - * We know that the chip has FIFOs. Does it have an EFR? The - * EFR is located in the same register position as the IIR and - * we know the top two bits of the IIR are currently set. The - * EFR should contain zero. Try to read the EFR. - */ -static void autoconfig_16550a(struct uart_8250_port *up) -{ - unsigned char status1, status2; - unsigned int iersave; - - up->port.type = PORT_16550A; - up->capabilities |= UART_CAP_FIFO; - - /* - * XR17V35x UARTs have an extra divisor register, DLD - * that gets enabled with when DLAB is set which will - * cause the device to incorrectly match and assign - * port type to PORT_16650. The EFR for this UART is - * found at offset 0x09. Instead check the Deice ID (DVID) - * register for a 2, 4 or 8 port UART. - */ - if (up->port.flags & UPF_EXAR_EFR) { - status1 = serial_in(up, UART_EXAR_DVID); - if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) { - DEBUG_AUTOCONF("Exar XR17V35x "); - up->port.type = PORT_XR17V35X; - up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | - UART_CAP_SLEEP; - - return; - } - - } - - /* - * Check for presence of the EFR when DLAB is set. - * Only ST16C650V1 UARTs pass this test. - */ - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - if (serial_in(up, UART_EFR) == 0) { - serial_out(up, UART_EFR, 0xA8); - if (serial_in(up, UART_EFR) != 0) { - DEBUG_AUTOCONF("EFRv1 "); - up->port.type = PORT_16650; - up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; - } else { - serial_out(up, UART_LCR, 0); - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | - UART_FCR7_64BYTE); - status1 = serial_in(up, UART_IIR) >> 5; - serial_out(up, UART_FCR, 0); - serial_out(up, UART_LCR, 0); - - if (status1 == 7) - up->port.type = PORT_16550A_FSL64; - else - DEBUG_AUTOCONF("Motorola 8xxx DUART "); - } - serial_out(up, UART_EFR, 0); - return; - } - - /* - * Maybe it requires 0xbf to be written to the LCR. - * (other ST16C650V2 UARTs, TI16C752A, etc) - */ - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) { - DEBUG_AUTOCONF("EFRv2 "); - autoconfig_has_efr(up); - return; - } - - /* - * Check for a National Semiconductor SuperIO chip. - * Attempt to switch to bank 2, read the value of the LOOP bit - * from EXCR1. Switch back to bank 0, change it in MCR. Then - * switch back to bank 2, read it from EXCR1 again and check - * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2 - */ - serial_out(up, UART_LCR, 0); - status1 = serial_in(up, UART_MCR); - serial_out(up, UART_LCR, 0xE0); - status2 = serial_in(up, 0x02); /* EXCR1 */ - - if (!((status2 ^ status1) & UART_MCR_LOOP)) { - serial_out(up, UART_LCR, 0); - serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP); - serial_out(up, UART_LCR, 0xE0); - status2 = serial_in(up, 0x02); /* EXCR1 */ - serial_out(up, UART_LCR, 0); - serial_out(up, UART_MCR, status1); - - if ((status2 ^ status1) & UART_MCR_LOOP) { - unsigned short quot; - - serial_out(up, UART_LCR, 0xE0); - - quot = serial_dl_read(up); - quot <<= 3; - - if (ns16550a_goto_highspeed(up)) - serial_dl_write(up, quot); - - serial_out(up, UART_LCR, 0); - - up->port.uartclk = 921600*16; - up->port.type = PORT_NS16550A; - up->capabilities |= UART_NATSEMI; - return; - } - } - - /* - * No EFR. Try to detect a TI16750, which only sets bit 5 of - * the IIR when 64 byte FIFO mode is enabled when DLAB is set. - * Try setting it with and without DLAB set. Cheap clones - * set bit 5 without DLAB set. - */ - serial_out(up, UART_LCR, 0); - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); - status1 = serial_in(up, UART_IIR) >> 5; - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); - status2 = serial_in(up, UART_IIR) >> 5; - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); - serial_out(up, UART_LCR, 0); - - DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2); - - if (status1 == 6 && status2 == 7) { - up->port.type = PORT_16750; - up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP; - return; - } - - /* - * Try writing and reading the UART_IER_UUE bit (b6). - * If it works, this is probably one of the Xscale platform's - * internal UARTs. - * We're going to explicitly set the UUE bit to 0 before - * trying to write and read a 1 just to make sure it's not - * already a 1 and maybe locked there before we even start start. - */ - iersave = serial_in(up, UART_IER); - serial_out(up, UART_IER, iersave & ~UART_IER_UUE); - if (!(serial_in(up, UART_IER) & UART_IER_UUE)) { - /* - * OK it's in a known zero state, try writing and reading - * without disturbing the current state of the other bits. - */ - serial_out(up, UART_IER, iersave | UART_IER_UUE); - if (serial_in(up, UART_IER) & UART_IER_UUE) { - /* - * It's an Xscale. - * We'll leave the UART_IER_UUE bit set to 1 (enabled). - */ - DEBUG_AUTOCONF("Xscale "); - up->port.type = PORT_XSCALE; - up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE; - return; - } - } else { - /* - * If we got here we couldn't force the IER_UUE bit to 0. - * Log it and continue. - */ - DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 "); - } - serial_out(up, UART_IER, iersave); - - /* - * Exar uarts have EFR in a weird location - */ - if (up->port.flags & UPF_EXAR_EFR) { - DEBUG_AUTOCONF("Exar XR17D15x "); - up->port.type = PORT_XR17D15X; - up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | - UART_CAP_SLEEP; - - return; - } - - /* - * We distinguish between 16550A and U6 16550A by counting - * how many bytes are in the FIFO. - */ - if (up->port.type == PORT_16550A && size_fifo(up) == 64) { - up->port.type = PORT_U6_16550A; - up->capabilities |= UART_CAP_AFE; - } -} - -/* - * This routine is called by rs_init() to initialize a specific serial - * port. It determines what type of UART chip this serial port is - * using: 8250, 16450, 16550, 16550A. The important question is - * whether or not this UART is a 16550A or not, since this will - * determine whether or not we can use its FIFO features or not. - */ -static void autoconfig(struct uart_8250_port *up) -{ - unsigned char status1, scratch, scratch2, scratch3; - unsigned char save_lcr, save_mcr; - struct uart_port *port = &up->port; - unsigned long flags; - unsigned int old_capabilities; - - if (!port->iobase && !port->mapbase && !port->membase) - return; - - DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ", - serial_index(port), port->iobase, port->membase); - - /* - * We really do need global IRQs disabled here - we're going to - * be frobbing the chips IRQ enable register to see if it exists. - */ - spin_lock_irqsave(&port->lock, flags); - - up->capabilities = 0; - up->bugs = 0; - - if (!(port->flags & UPF_BUGGY_UART)) { - /* - * Do a simple existence test first; if we fail this, - * there's no point trying anything else. - * - * 0x80 is used as a nonsense port to prevent against - * false positives due to ISA bus float. The - * assumption is that 0x80 is a non-existent port; - * which should be safe since include/asm/io.h also - * makes this assumption. - * - * Note: this is safe as long as MCR bit 4 is clear - * and the device is in "PC" mode. - */ - scratch = serial_in(up, UART_IER); - serial_out(up, UART_IER, 0); -#ifdef __i386__ - outb(0xff, 0x080); -#endif - /* - * Mask out IER[7:4] bits for test as some UARTs (e.g. TL - * 16C754B) allow only to modify them if an EFR bit is set. - */ - scratch2 = serial_in(up, UART_IER) & 0x0f; - serial_out(up, UART_IER, 0x0F); -#ifdef __i386__ - outb(0, 0x080); -#endif - scratch3 = serial_in(up, UART_IER) & 0x0f; - serial_out(up, UART_IER, scratch); - if (scratch2 != 0 || scratch3 != 0x0F) { - /* - * We failed; there's nothing here - */ - spin_unlock_irqrestore(&port->lock, flags); - DEBUG_AUTOCONF("IER test failed (%02x, %02x) ", - scratch2, scratch3); - goto out; - } - } - - save_mcr = serial_in(up, UART_MCR); - save_lcr = serial_in(up, UART_LCR); - - /* - * Check to see if a UART is really there. Certain broken - * internal modems based on the Rockwell chipset fail this - * test, because they apparently don't implement the loopback - * test mode. So this test is skipped on the COM 1 through - * COM 4 ports. This *should* be safe, since no board - * manufacturer would be stupid enough to design a board - * that conflicts with COM 1-4 --- we hope! - */ - if (!(port->flags & UPF_SKIP_TEST)) { - serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A); - status1 = serial_in(up, UART_MSR) & 0xF0; - serial_out(up, UART_MCR, save_mcr); - if (status1 != 0x90) { - spin_unlock_irqrestore(&port->lock, flags); - DEBUG_AUTOCONF("LOOP test failed (%02x) ", - status1); - goto out; - } - } - - /* - * We're pretty sure there's a port here. Lets find out what - * type of port it is. The IIR top two bits allows us to find - * out if it's 8250 or 16450, 16550, 16550A or later. This - * determines what we test for next. - * - * We also initialise the EFR (if any) to zero for later. The - * EFR occupies the same register location as the FCR and IIR. - */ - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, 0); - serial_out(up, UART_LCR, 0); - - serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); - scratch = serial_in(up, UART_IIR) >> 6; - - switch (scratch) { - case 0: - autoconfig_8250(up); - break; - case 1: - port->type = PORT_UNKNOWN; - break; - case 2: - port->type = PORT_16550; - break; - case 3: - autoconfig_16550a(up); - break; - } - -#ifdef CONFIG_SERIAL_8250_RSA - /* - * Only probe for RSA ports if we got the region. - */ - if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA && - __enable_rsa(up)) - port->type = PORT_RSA; -#endif - - serial_out(up, UART_LCR, save_lcr); - - port->fifosize = uart_config[up->port.type].fifo_size; - old_capabilities = up->capabilities; - up->capabilities = uart_config[port->type].flags; - up->tx_loadsz = uart_config[port->type].tx_loadsz; - - if (port->type == PORT_UNKNOWN) - goto out_lock; - - /* - * Reset the UART. - */ -#ifdef CONFIG_SERIAL_8250_RSA - if (port->type == PORT_RSA) - serial_out(up, UART_RSA_FRR, 0); -#endif - serial_out(up, UART_MCR, save_mcr); - serial8250_clear_fifos(up); - serial_in(up, UART_RX); - if (up->capabilities & UART_CAP_UUE) - serial_out(up, UART_IER, UART_IER_UUE); - else - serial_out(up, UART_IER, 0); - -out_lock: - spin_unlock_irqrestore(&port->lock, flags); - if (up->capabilities != old_capabilities) { - printk(KERN_WARNING - "ttyS%d: detected caps %08x should be %08x\n", - serial_index(port), old_capabilities, - up->capabilities); - } -out: - DEBUG_AUTOCONF("iir=%d ", scratch); - DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name); -} - -static void autoconfig_irq(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - unsigned char save_mcr, save_ier; - unsigned char save_ICP = 0; - unsigned int ICP = 0; - unsigned long irqs; - int irq; - - if (port->flags & UPF_FOURPORT) { - ICP = (port->iobase & 0xfe0) | 0x1f; - save_ICP = inb_p(ICP); - outb_p(0x80, ICP); - inb_p(ICP); - } - - /* forget possible initially masked and pending IRQ */ - probe_irq_off(probe_irq_on()); - save_mcr = serial_in(up, UART_MCR); - save_ier = serial_in(up, UART_IER); - serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2); - - irqs = probe_irq_on(); - serial_out(up, UART_MCR, 0); - udelay(10); - if (port->flags & UPF_FOURPORT) { - serial_out(up, UART_MCR, - UART_MCR_DTR | UART_MCR_RTS); - } else { - serial_out(up, UART_MCR, - UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2); - } - serial_out(up, UART_IER, 0x0f); /* enable all intrs */ - serial_in(up, UART_LSR); - serial_in(up, UART_RX); - serial_in(up, UART_IIR); - serial_in(up, UART_MSR); - serial_out(up, UART_TX, 0xFF); - udelay(20); - irq = probe_irq_off(irqs); - - serial_out(up, UART_MCR, save_mcr); - serial_out(up, UART_IER, save_ier); - - if (port->flags & UPF_FOURPORT) - outb_p(save_ICP, ICP); - - port->irq = (irq > 0) ? irq : 0; -} - -static inline void __stop_tx(struct uart_8250_port *p) -{ - if (p->ier & UART_IER_THRI) { - p->ier &= ~UART_IER_THRI; - serial_out(p, UART_IER, p->ier); - serial8250_rpm_put_tx(p); - } -} - -static void serial8250_stop_tx(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_rpm_get(up); - __stop_tx(up); - - /* - * We really want to stop the transmitter from sending. - */ - if (port->type == PORT_16C950) { - up->acr |= UART_ACR_TXDIS; - serial_icr_write(up, UART_ACR, up->acr); - } - serial8250_rpm_put(up); -} - -static void serial8250_start_tx(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_rpm_get_tx(up); - - if (up->dma && !up->dma->tx_dma(up)) - return; - - if (!(up->ier & UART_IER_THRI)) { - up->ier |= UART_IER_THRI; - serial_port_out(port, UART_IER, up->ier); - - if (up->bugs & UART_BUG_TXEN) { - unsigned char lsr; - lsr = serial_in(up, UART_LSR); - up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; - if (lsr & UART_LSR_THRE) - serial8250_tx_chars(up); - } - } - - /* - * Re-enable the transmitter if we disabled it. - */ - if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) { - up->acr &= ~UART_ACR_TXDIS; - serial_icr_write(up, UART_ACR, up->acr); - } -} - -static void serial8250_throttle(struct uart_port *port) -{ - port->throttle(port); -} - -static void serial8250_unthrottle(struct uart_port *port) -{ - port->unthrottle(port); -} - -static void serial8250_stop_rx(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_rpm_get(up); - - up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); - up->port.read_status_mask &= ~UART_LSR_DR; - serial_port_out(port, UART_IER, up->ier); - - serial8250_rpm_put(up); -} - -static void serial8250_disable_ms(struct uart_port *port) -{ - struct uart_8250_port *up = - container_of(port, struct uart_8250_port, port); - - /* no MSR capabilities */ - if (up->bugs & UART_BUG_NOMSR) - return; - - up->ier &= ~UART_IER_MSI; - serial_port_out(port, UART_IER, up->ier); -} - -static void serial8250_enable_ms(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - /* no MSR capabilities */ - if (up->bugs & UART_BUG_NOMSR) - return; - - up->ier |= UART_IER_MSI; - - serial8250_rpm_get(up); - serial_port_out(port, UART_IER, up->ier); - serial8250_rpm_put(up); -} - -/* - * serial8250_rx_chars: processes according to the passed in LSR - * value, and returns the remaining LSR bits not handled - * by this Rx routine. - */ -unsigned char -serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr) -{ - struct uart_port *port = &up->port; - unsigned char ch; - int max_count = 256; - char flag; - - do { - if (likely(lsr & UART_LSR_DR)) - ch = serial_in(up, UART_RX); - else - /* - * Intel 82571 has a Serial Over Lan device that will - * set UART_LSR_BI without setting UART_LSR_DR when - * it receives a break. To avoid reading from the - * receive buffer without UART_LSR_DR bit set, we - * just force the read character to be 0 - */ - ch = 0; - - flag = TTY_NORMAL; - port->icount.rx++; - - lsr |= up->lsr_saved_flags; - up->lsr_saved_flags = 0; - - if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) { - if (lsr & UART_LSR_BI) { - lsr &= ~(UART_LSR_FE | UART_LSR_PE); - port->icount.brk++; - /* - * We do the SysRQ and SAK checking - * here because otherwise the break - * may get masked by ignore_status_mask - * or read_status_mask. - */ - if (uart_handle_break(port)) - goto ignore_char; - } else if (lsr & UART_LSR_PE) - port->icount.parity++; - else if (lsr & UART_LSR_FE) - port->icount.frame++; - if (lsr & UART_LSR_OE) - port->icount.overrun++; - - /* - * Mask off conditions which should be ignored. - */ - lsr &= port->read_status_mask; - - if (lsr & UART_LSR_BI) { - DEBUG_INTR("handling break...."); - flag = TTY_BREAK; - } else if (lsr & UART_LSR_PE) - flag = TTY_PARITY; - else if (lsr & UART_LSR_FE) - flag = TTY_FRAME; - } - if (uart_handle_sysrq_char(port, ch)) - goto ignore_char; - - uart_insert_char(port, lsr, UART_LSR_OE, ch, flag); - -ignore_char: - lsr = serial_in(up, UART_LSR); - } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0)); - spin_unlock(&port->lock); - tty_flip_buffer_push(&port->state->port); - spin_lock(&port->lock); - return lsr; -} -EXPORT_SYMBOL_GPL(serial8250_rx_chars); - -void serial8250_tx_chars(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - struct circ_buf *xmit = &port->state->xmit; - int count; - - if (port->x_char) { - serial_out(up, UART_TX, port->x_char); - port->icount.tx++; - port->x_char = 0; - return; - } - if (uart_tx_stopped(port)) { - serial8250_stop_tx(port); - return; - } - if (uart_circ_empty(xmit)) { - __stop_tx(up); - return; - } - - count = up->tx_loadsz; - do { - serial_out(up, UART_TX, xmit->buf[xmit->tail]); - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - port->icount.tx++; - if (uart_circ_empty(xmit)) - break; - if (up->capabilities & UART_CAP_HFIFO) { - if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) != - BOTH_EMPTY) - break; - } - } while (--count > 0); - - if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) - uart_write_wakeup(port); - - DEBUG_INTR("THRE..."); - - /* - * With RPM enabled, we have to wait until the FIFO is empty before the - * HW can go idle. So we get here once again with empty FIFO and disable - * the interrupt and RPM in __stop_tx() - */ - if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM)) - __stop_tx(up); -} -EXPORT_SYMBOL_GPL(serial8250_tx_chars); - -/* Caller holds uart port lock */ -unsigned int serial8250_modem_status(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - unsigned int status = serial_in(up, UART_MSR); - - status |= up->msr_saved_flags; - up->msr_saved_flags = 0; - if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI && - port->state != NULL) { - if (status & UART_MSR_TERI) - port->icount.rng++; - if (status & UART_MSR_DDSR) - port->icount.dsr++; - if (status & UART_MSR_DDCD) - uart_handle_dcd_change(port, status & UART_MSR_DCD); - if (status & UART_MSR_DCTS) - uart_handle_cts_change(port, status & UART_MSR_CTS); - - wake_up_interruptible(&port->state->port.delta_msr_wait); - } - - return status; -} -EXPORT_SYMBOL_GPL(serial8250_modem_status); - -/* - * This handles the interrupt from one port. - */ -int serial8250_handle_irq(struct uart_port *port, unsigned int iir) -{ - unsigned char status; - unsigned long flags; - struct uart_8250_port *up = up_to_u8250p(port); - int dma_err = 0; - - if (iir & UART_IIR_NO_INT) - return 0; - - spin_lock_irqsave(&port->lock, flags); - - status = serial_port_in(port, UART_LSR); - - DEBUG_INTR("status = %x...", status); - - if (status & (UART_LSR_DR | UART_LSR_BI)) { - if (up->dma) - dma_err = up->dma->rx_dma(up, iir); - - if (!up->dma || dma_err) - status = serial8250_rx_chars(up, status); - } - serial8250_modem_status(up); - if ((!up->dma || (up->dma && up->dma->tx_err)) && - (status & UART_LSR_THRE)) - serial8250_tx_chars(up); - - spin_unlock_irqrestore(&port->lock, flags); - return 1; -} -EXPORT_SYMBOL_GPL(serial8250_handle_irq); - -static int serial8250_default_handle_irq(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned int iir; - int ret; - - serial8250_rpm_get(up); - - iir = serial_port_in(port, UART_IIR); - ret = serial8250_handle_irq(port, iir); - - serial8250_rpm_put(up); - return ret; -} - -/* - * These Exar UARTs have an extra interrupt indicator that could - * fire for a few unimplemented interrupts. One of which is a - * wakeup event when coming out of sleep. Put this here just - * to be on the safe side that these interrupts don't go unhandled. - */ -static int exar_handle_irq(struct uart_port *port) -{ - unsigned char int0, int1, int2, int3; - unsigned int iir = serial_port_in(port, UART_IIR); - int ret; - - ret = serial8250_handle_irq(port, iir); - - if ((port->type == PORT_XR17V35X) || - (port->type == PORT_XR17D15X)) { - int0 = serial_port_in(port, 0x80); - int1 = serial_port_in(port, 0x81); - int2 = serial_port_in(port, 0x82); - int3 = serial_port_in(port, 0x83); - } - - return ret; -} - -/* - * This is the serial driver's interrupt routine. - * - * Arjan thinks the old way was overly complex, so it got simplified. - * Alan disagrees, saying that need the complexity to handle the weird - * nature of ISA shared interrupts. (This is a special exception.) - * - * In order to handle ISA shared interrupts properly, we need to check - * that all ports have been serviced, and therefore the ISA interrupt - * line has been de-asserted. - * - * This means we need to loop through all ports. checking that they - * don't have an interrupt pending. - */ -static irqreturn_t serial8250_interrupt(int irq, void *dev_id) -{ - struct irq_info *i = dev_id; - struct list_head *l, *end = NULL; - int pass_counter = 0, handled = 0; - - DEBUG_INTR("serial8250_interrupt(%d)...", irq); - - spin_lock(&i->lock); - - l = i->head; - do { - struct uart_8250_port *up; - struct uart_port *port; - - up = list_entry(l, struct uart_8250_port, list); - port = &up->port; - - if (port->handle_irq(port)) { - handled = 1; - end = NULL; - } else if (end == NULL) - end = l; - - l = l->next; - - if (l == i->head && pass_counter++ > PASS_LIMIT) { - /* If we hit this, we're dead. */ - printk_ratelimited(KERN_ERR - "serial8250: too much work for irq%d\n", irq); - break; - } - } while (l != end); - - spin_unlock(&i->lock); - - DEBUG_INTR("end.\n"); - - return IRQ_RETVAL(handled); -} - -/* - * To support ISA shared interrupts, we need to have one interrupt - * handler that ensures that the IRQ line has been deasserted - * before returning. Failing to do this will result in the IRQ - * line being stuck active, and, since ISA irqs are edge triggered, - * no more IRQs will be seen. - */ -static void serial_do_unlink(struct irq_info *i, struct uart_8250_port *up) -{ - spin_lock_irq(&i->lock); - - if (!list_empty(i->head)) { - if (i->head == &up->list) - i->head = i->head->next; - list_del(&up->list); - } else { - BUG_ON(i->head != &up->list); - i->head = NULL; - } - spin_unlock_irq(&i->lock); - /* List empty so throw away the hash node */ - if (i->head == NULL) { - hlist_del(&i->node); - kfree(i); - } -} - -static int serial_link_irq_chain(struct uart_8250_port *up) -{ - struct hlist_head *h; - struct hlist_node *n; - struct irq_info *i; - int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? IRQF_SHARED : 0; - - mutex_lock(&hash_mutex); - - h = &irq_lists[up->port.irq % NR_IRQ_HASH]; - - hlist_for_each(n, h) { - i = hlist_entry(n, struct irq_info, node); - if (i->irq == up->port.irq) - break; - } - - if (n == NULL) { - i = kzalloc(sizeof(struct irq_info), GFP_KERNEL); - if (i == NULL) { - mutex_unlock(&hash_mutex); - return -ENOMEM; - } - spin_lock_init(&i->lock); - i->irq = up->port.irq; - hlist_add_head(&i->node, h); - } - mutex_unlock(&hash_mutex); - - spin_lock_irq(&i->lock); - - if (i->head) { - list_add(&up->list, i->head); - spin_unlock_irq(&i->lock); - - ret = 0; - } else { - INIT_LIST_HEAD(&up->list); - i->head = &up->list; - spin_unlock_irq(&i->lock); - irq_flags |= up->port.irqflags; - ret = request_irq(up->port.irq, serial8250_interrupt, - irq_flags, "serial", i); - if (ret < 0) - serial_do_unlink(i, up); - } - - return ret; -} - -static void serial_unlink_irq_chain(struct uart_8250_port *up) -{ - /* - * yes, some broken gcc emit "warning: 'i' may be used uninitialized" - * but no, we are not going to take a patch that assigns NULL below. - */ - struct irq_info *i; - struct hlist_node *n; - struct hlist_head *h; - - mutex_lock(&hash_mutex); - - h = &irq_lists[up->port.irq % NR_IRQ_HASH]; - - hlist_for_each(n, h) { - i = hlist_entry(n, struct irq_info, node); - if (i->irq == up->port.irq) - break; - } - - BUG_ON(n == NULL); - BUG_ON(i->head == NULL); - - if (list_empty(i->head)) - free_irq(up->port.irq, i); - - serial_do_unlink(i, up); - mutex_unlock(&hash_mutex); -} - -/* - * This function is used to handle ports that do not have an - * interrupt. This doesn't work very well for 16450's, but gives - * barely passable results for a 16550A. (Although at the expense - * of much CPU overhead). - */ -static void serial8250_timeout(unsigned long data) -{ - struct uart_8250_port *up = (struct uart_8250_port *)data; - - up->port.handle_irq(&up->port); - mod_timer(&up->timer, jiffies + uart_poll_timeout(&up->port)); -} - -static void serial8250_backup_timeout(unsigned long data) -{ - struct uart_8250_port *up = (struct uart_8250_port *)data; - unsigned int iir, ier = 0, lsr; - unsigned long flags; - - spin_lock_irqsave(&up->port.lock, flags); - - /* - * Must disable interrupts or else we risk racing with the interrupt - * based handler. - */ - if (up->port.irq) { - ier = serial_in(up, UART_IER); - serial_out(up, UART_IER, 0); - } - - iir = serial_in(up, UART_IIR); - - /* - * This should be a safe test for anyone who doesn't trust the - * IIR bits on their UART, but it's specifically designed for - * the "Diva" UART used on the management processor on many HP - * ia64 and parisc boxes. - */ - lsr = serial_in(up, UART_LSR); - up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; - if ((iir & UART_IIR_NO_INT) && (up->ier & UART_IER_THRI) && - (!uart_circ_empty(&up->port.state->xmit) || up->port.x_char) && - (lsr & UART_LSR_THRE)) { - iir &= ~(UART_IIR_ID | UART_IIR_NO_INT); - iir |= UART_IIR_THRI; - } - - if (!(iir & UART_IIR_NO_INT)) - serial8250_tx_chars(up); - - if (up->port.irq) - serial_out(up, UART_IER, ier); - - spin_unlock_irqrestore(&up->port.lock, flags); - - /* Standard timer interval plus 0.2s to keep the port running */ - mod_timer(&up->timer, - jiffies + uart_poll_timeout(&up->port) + HZ / 5); -} - -static int univ8250_setup_irq(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - int retval = 0; - - /* - * The above check will only give an accurate result the first time - * the port is opened so this value needs to be preserved. - */ - if (up->bugs & UART_BUG_THRE) { - pr_debug("ttyS%d - using backup timer\n", serial_index(port)); - - up->timer.function = serial8250_backup_timeout; - up->timer.data = (unsigned long)up; - mod_timer(&up->timer, jiffies + - uart_poll_timeout(port) + HZ / 5); - } - - /* - * If the "interrupt" for this port doesn't correspond with any - * hardware interrupt, we use a timer-based system. The original - * driver used to do this with IRQ0. - */ - if (!port->irq) { - up->timer.data = (unsigned long)up; - mod_timer(&up->timer, jiffies + uart_poll_timeout(port)); - } else - retval = serial_link_irq_chain(up); - - return retval; -} - -static void univ8250_release_irq(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - - del_timer_sync(&up->timer); - up->timer.function = serial8250_timeout; - if (port->irq) - serial_unlink_irq_chain(up); -} - -static unsigned int serial8250_tx_empty(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned long flags; - unsigned int lsr; - - serial8250_rpm_get(up); - - spin_lock_irqsave(&port->lock, flags); - lsr = serial_port_in(port, UART_LSR); - up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; - spin_unlock_irqrestore(&port->lock, flags); - - serial8250_rpm_put(up); - - return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0; -} - -static unsigned int serial8250_get_mctrl(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned int status; - unsigned int ret; - - serial8250_rpm_get(up); - status = serial8250_modem_status(up); - serial8250_rpm_put(up); - - ret = 0; - if (status & UART_MSR_DCD) - ret |= TIOCM_CAR; - if (status & UART_MSR_RI) - ret |= TIOCM_RNG; - if (status & UART_MSR_DSR) - ret |= TIOCM_DSR; - if (status & UART_MSR_CTS) - ret |= TIOCM_CTS; - return ret; -} - -void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned char mcr = 0; - - if (mctrl & TIOCM_RTS) - mcr |= UART_MCR_RTS; - if (mctrl & TIOCM_DTR) - mcr |= UART_MCR_DTR; - if (mctrl & TIOCM_OUT1) - mcr |= UART_MCR_OUT1; - if (mctrl & TIOCM_OUT2) - mcr |= UART_MCR_OUT2; - if (mctrl & TIOCM_LOOP) - mcr |= UART_MCR_LOOP; - - mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; - - serial_port_out(port, UART_MCR, mcr); -} -EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl); - -static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl) -{ - if (port->set_mctrl) - port->set_mctrl(port, mctrl); - else - serial8250_do_set_mctrl(port, mctrl); -} - -static void serial8250_break_ctl(struct uart_port *port, int break_state) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned long flags; - - serial8250_rpm_get(up); - spin_lock_irqsave(&port->lock, flags); - if (break_state == -1) - up->lcr |= UART_LCR_SBC; - else - up->lcr &= ~UART_LCR_SBC; - serial_port_out(port, UART_LCR, up->lcr); - spin_unlock_irqrestore(&port->lock, flags); - serial8250_rpm_put(up); -} - -/* - * Wait for transmitter & holding register to empty - */ -static void wait_for_xmitr(struct uart_8250_port *up, int bits) -{ - unsigned int status, tmout = 10000; - - /* Wait up to 10ms for the character(s) to be sent. */ - for (;;) { - status = serial_in(up, UART_LSR); - - up->lsr_saved_flags |= status & LSR_SAVE_FLAGS; - - if ((status & bits) == bits) - break; - if (--tmout == 0) - break; - udelay(1); - } - - /* Wait up to 1s for flow control if necessary */ - if (up->port.flags & UPF_CONS_FLOW) { - unsigned int tmout; - for (tmout = 1000000; tmout; tmout--) { - unsigned int msr = serial_in(up, UART_MSR); - up->msr_saved_flags |= msr & MSR_SAVE_FLAGS; - if (msr & UART_MSR_CTS) - break; - udelay(1); - touch_nmi_watchdog(); - } - } -} - -#ifdef CONFIG_CONSOLE_POLL -/* - * Console polling routines for writing and reading from the uart while - * in an interrupt or debug context. - */ - -static int serial8250_get_poll_char(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned char lsr; - int status; - - serial8250_rpm_get(up); - - lsr = serial_port_in(port, UART_LSR); - - if (!(lsr & UART_LSR_DR)) { - status = NO_POLL_CHAR; - goto out; - } - - status = serial_port_in(port, UART_RX); -out: - serial8250_rpm_put(up); - return status; -} - - -static void serial8250_put_poll_char(struct uart_port *port, - unsigned char c) -{ - unsigned int ier; - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_rpm_get(up); - /* - * First save the IER then disable the interrupts - */ - ier = serial_port_in(port, UART_IER); - if (up->capabilities & UART_CAP_UUE) - serial_port_out(port, UART_IER, UART_IER_UUE); - else - serial_port_out(port, UART_IER, 0); - - wait_for_xmitr(up, BOTH_EMPTY); - /* - * Send the character out. - */ - serial_port_out(port, UART_TX, c); - - /* - * Finally, wait for transmitter to become empty - * and restore the IER - */ - wait_for_xmitr(up, BOTH_EMPTY); - serial_port_out(port, UART_IER, ier); - serial8250_rpm_put(up); -} - -#endif /* CONFIG_CONSOLE_POLL */ - -int serial8250_do_startup(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned long flags; - unsigned char lsr, iir; - int retval; - - if (port->type == PORT_8250_CIR) - return -ENODEV; - - if (!port->fifosize) - port->fifosize = uart_config[port->type].fifo_size; - if (!up->tx_loadsz) - up->tx_loadsz = uart_config[port->type].tx_loadsz; - if (!up->capabilities) - up->capabilities = uart_config[port->type].flags; - up->mcr = 0; - - if (port->iotype != up->cur_iotype) - set_io_from_upio(port); - - serial8250_rpm_get(up); - if (port->type == PORT_16C950) { - /* Wake up and initialize UART */ - up->acr = 0; - serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); - serial_port_out(port, UART_EFR, UART_EFR_ECB); - serial_port_out(port, UART_IER, 0); - serial_port_out(port, UART_LCR, 0); - serial_icr_write(up, UART_CSR, 0); /* Reset the UART */ - serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); - serial_port_out(port, UART_EFR, UART_EFR_ECB); - serial_port_out(port, UART_LCR, 0); - } - -#ifdef CONFIG_SERIAL_8250_RSA - /* - * If this is an RSA port, see if we can kick it up to the - * higher speed clock. - */ - enable_rsa(up); -#endif - /* - * Clear the FIFO buffers and disable them. - * (they will be reenabled in set_termios()) - */ - serial8250_clear_fifos(up); - - /* - * Clear the interrupt registers. - */ - serial_port_in(port, UART_LSR); - serial_port_in(port, UART_RX); - serial_port_in(port, UART_IIR); - serial_port_in(port, UART_MSR); - - /* - * At this point, there's no way the LSR could still be 0xff; - * if it is, then bail out, because there's likely no UART - * here. - */ - if (!(port->flags & UPF_BUGGY_UART) && - (serial_port_in(port, UART_LSR) == 0xff)) { - printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n", - serial_index(port)); - retval = -ENODEV; - goto out; - } - - /* - * For a XR16C850, we need to set the trigger levels - */ - if (port->type == PORT_16850) { - unsigned char fctr; - - serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - - fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX); - serial_port_out(port, UART_FCTR, - fctr | UART_FCTR_TRGD | UART_FCTR_RX); - serial_port_out(port, UART_TRG, UART_TRG_96); - serial_port_out(port, UART_FCTR, - fctr | UART_FCTR_TRGD | UART_FCTR_TX); - serial_port_out(port, UART_TRG, UART_TRG_96); - - serial_port_out(port, UART_LCR, 0); - } - - if (port->irq) { - unsigned char iir1; - /* - * Test for UARTs that do not reassert THRE when the - * transmitter is idle and the interrupt has already - * been cleared. Real 16550s should always reassert - * this interrupt whenever the transmitter is idle and - * the interrupt is enabled. Delays are necessary to - * allow register changes to become visible. - */ - spin_lock_irqsave(&port->lock, flags); - if (up->port.irqflags & IRQF_SHARED) - disable_irq_nosync(port->irq); - - wait_for_xmitr(up, UART_LSR_THRE); - serial_port_out_sync(port, UART_IER, UART_IER_THRI); - udelay(1); /* allow THRE to set */ - iir1 = serial_port_in(port, UART_IIR); - serial_port_out(port, UART_IER, 0); - serial_port_out_sync(port, UART_IER, UART_IER_THRI); - udelay(1); /* allow a working UART time to re-assert THRE */ - iir = serial_port_in(port, UART_IIR); - serial_port_out(port, UART_IER, 0); - - if (port->irqflags & IRQF_SHARED) - enable_irq(port->irq); - spin_unlock_irqrestore(&port->lock, flags); - - /* - * If the interrupt is not reasserted, or we otherwise - * don't trust the iir, setup a timer to kick the UART - * on a regular basis. - */ - if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) || - up->port.flags & UPF_BUG_THRE) { - up->bugs |= UART_BUG_THRE; - } - } - - retval = up->ops->setup_irq(up); - if (retval) - goto out; - - /* - * Now, initialize the UART - */ - serial_port_out(port, UART_LCR, UART_LCR_WLEN8); - - spin_lock_irqsave(&port->lock, flags); - if (up->port.flags & UPF_FOURPORT) { - if (!up->port.irq) - up->port.mctrl |= TIOCM_OUT1; - } else - /* - * Most PC uarts need OUT2 raised to enable interrupts. - */ - if (port->irq) - up->port.mctrl |= TIOCM_OUT2; - - serial8250_set_mctrl(port, port->mctrl); - - /* Serial over Lan (SoL) hack: - Intel 8257x Gigabit ethernet chips have a - 16550 emulation, to be used for Serial Over Lan. - Those chips take a longer time than a normal - serial device to signalize that a transmission - data was queued. Due to that, the above test generally - fails. One solution would be to delay the reading of - iir. However, this is not reliable, since the timeout - is variable. So, let's just don't test if we receive - TX irq. This way, we'll never enable UART_BUG_TXEN. - */ - if (up->port.flags & UPF_NO_TXEN_TEST) - goto dont_test_tx_en; - - /* - * Do a quick test to see if we receive an - * interrupt when we enable the TX irq. - */ - serial_port_out(port, UART_IER, UART_IER_THRI); - lsr = serial_port_in(port, UART_LSR); - iir = serial_port_in(port, UART_IIR); - serial_port_out(port, UART_IER, 0); - - if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { - if (!(up->bugs & UART_BUG_TXEN)) { - up->bugs |= UART_BUG_TXEN; - pr_debug("ttyS%d - enabling bad tx status workarounds\n", - serial_index(port)); - } - } else { - up->bugs &= ~UART_BUG_TXEN; - } - -dont_test_tx_en: - spin_unlock_irqrestore(&port->lock, flags); - - /* - * Clear the interrupt registers again for luck, and clear the - * saved flags to avoid getting false values from polling - * routines or the previous session. - */ - serial_port_in(port, UART_LSR); - serial_port_in(port, UART_RX); - serial_port_in(port, UART_IIR); - serial_port_in(port, UART_MSR); - up->lsr_saved_flags = 0; - up->msr_saved_flags = 0; - - /* - * Request DMA channels for both RX and TX. - */ - if (up->dma) { - retval = serial8250_request_dma(up); - if (retval) { - pr_warn_ratelimited("ttyS%d - failed to request DMA\n", - serial_index(port)); - up->dma = NULL; - } - } - - /* - * Finally, enable interrupts. Note: Modem status interrupts - * are set via set_termios(), which will be occurring imminently - * anyway, so we don't enable them here. - */ - up->ier = UART_IER_RLSI | UART_IER_RDI; - serial_port_out(port, UART_IER, up->ier); - - if (port->flags & UPF_FOURPORT) { - unsigned int icp; - /* - * Enable interrupts on the AST Fourport board - */ - icp = (port->iobase & 0xfe0) | 0x01f; - outb_p(0x80, icp); - inb_p(icp); - } - retval = 0; -out: - serial8250_rpm_put(up); - return retval; -} -EXPORT_SYMBOL_GPL(serial8250_do_startup); - -static int serial8250_startup(struct uart_port *port) -{ - if (port->startup) - return port->startup(port); - return serial8250_do_startup(port); -} - -void serial8250_do_shutdown(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned long flags; - - serial8250_rpm_get(up); - /* - * Disable interrupts from this port - */ - up->ier = 0; - serial_port_out(port, UART_IER, 0); - - if (up->dma) - serial8250_release_dma(up); - - spin_lock_irqsave(&port->lock, flags); - if (port->flags & UPF_FOURPORT) { - /* reset interrupts on the AST Fourport board */ - inb((port->iobase & 0xfe0) | 0x1f); - port->mctrl |= TIOCM_OUT1; - } else - port->mctrl &= ~TIOCM_OUT2; - - serial8250_set_mctrl(port, port->mctrl); - spin_unlock_irqrestore(&port->lock, flags); - - /* - * Disable break condition and FIFOs - */ - serial_port_out(port, UART_LCR, - serial_port_in(port, UART_LCR) & ~UART_LCR_SBC); - serial8250_clear_fifos(up); - -#ifdef CONFIG_SERIAL_8250_RSA - /* - * Reset the RSA board back to 115kbps compat mode. - */ - disable_rsa(up); -#endif - - /* - * Read data port to reset things, and then unlink from - * the IRQ chain. - */ - serial_port_in(port, UART_RX); - serial8250_rpm_put(up); - - up->ops->release_irq(up); -} -EXPORT_SYMBOL_GPL(serial8250_do_shutdown); - -static void serial8250_shutdown(struct uart_port *port) -{ - if (port->shutdown) - port->shutdown(port); - else - serial8250_do_shutdown(port); -} - -/* - * XR17V35x UARTs have an extra fractional divisor register (DLD) - * Calculate divisor with extra 4-bit fractional portion - */ -static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up, - unsigned int baud, - unsigned int *frac) -{ - struct uart_port *port = &up->port; - unsigned int quot_16; - - quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud); - *frac = quot_16 & 0x0f; - - return quot_16 >> 4; -} - -static unsigned int serial8250_get_divisor(struct uart_8250_port *up, - unsigned int baud, - unsigned int *frac) -{ - struct uart_port *port = &up->port; - unsigned int quot; - - /* - * Handle magic divisors for baud rates above baud_base on - * SMSC SuperIO chips. - * - */ - if ((port->flags & UPF_MAGIC_MULTIPLIER) && - baud == (port->uartclk/4)) - quot = 0x8001; - else if ((port->flags & UPF_MAGIC_MULTIPLIER) && - baud == (port->uartclk/8)) - quot = 0x8002; - else if (up->port.type == PORT_XR17V35X) - quot = xr17v35x_get_divisor(up, baud, frac); - else - quot = uart_get_divisor(port, baud); - - /* - * Oxford Semi 952 rev B workaround - */ - if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0) - quot++; - - return quot; -} - -static unsigned char serial8250_compute_lcr(struct uart_8250_port *up, - tcflag_t c_cflag) -{ - unsigned char cval; - - switch (c_cflag & CSIZE) { - case CS5: - cval = UART_LCR_WLEN5; - break; - case CS6: - cval = UART_LCR_WLEN6; - break; - case CS7: - cval = UART_LCR_WLEN7; - break; - default: - case CS8: - cval = UART_LCR_WLEN8; - break; - } - - if (c_cflag & CSTOPB) - cval |= UART_LCR_STOP; - if (c_cflag & PARENB) { - cval |= UART_LCR_PARITY; - if (up->bugs & UART_BUG_PARITY) - up->fifo_bug = true; - } - if (!(c_cflag & PARODD)) - cval |= UART_LCR_EPAR; -#ifdef CMSPAR - if (c_cflag & CMSPAR) - cval |= UART_LCR_SPAR; -#endif - - return cval; -} - -static void serial8250_set_divisor(struct uart_port *port, unsigned int baud, - unsigned int quot, unsigned int quot_frac) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - /* Workaround to enable 115200 baud on OMAP1510 internal ports */ - if (is_omap1510_8250(up)) { - if (baud == 115200) { - quot = 1; - serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1); - } else - serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0); - } - - /* - * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2, - * otherwise just set DLAB - */ - if (up->capabilities & UART_NATSEMI) - serial_port_out(port, UART_LCR, 0xe0); - else - serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB); - - serial_dl_write(up, quot); - - /* XR17V35x UARTs have an extra fractional divisor register (DLD) */ - if (up->port.type == PORT_XR17V35X) - serial_port_out(port, 0x2, quot_frac); -} - -void -serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) -{ - struct uart_8250_port *up = up_to_u8250p(port); - unsigned char cval; - unsigned long flags; - unsigned int baud, quot, frac = 0; - - cval = serial8250_compute_lcr(up, termios->c_cflag); - - /* - * Ask the core to calculate the divisor for us. - */ - baud = uart_get_baud_rate(port, termios, old, - port->uartclk / 16 / 0xffff, - port->uartclk / 16); - quot = serial8250_get_divisor(up, baud, &frac); - - /* - * Ok, we're now changing the port state. Do it with - * interrupts disabled. - */ - serial8250_rpm_get(up); - spin_lock_irqsave(&port->lock, flags); - - up->lcr = cval; /* Save computed LCR */ - - if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) { - /* NOTE: If fifo_bug is not set, a user can set RX_trigger. */ - if ((baud < 2400 && !up->dma) || up->fifo_bug) { - up->fcr &= ~UART_FCR_TRIGGER_MASK; - up->fcr |= UART_FCR_TRIGGER_1; - } - } - - /* - * MCR-based auto flow control. When AFE is enabled, RTS will be - * deasserted when the receive FIFO contains more characters than - * the trigger, or the MCR RTS bit is cleared. In the case where - * the remote UART is not using CTS auto flow control, we must - * have sufficient FIFO entries for the latency of the remote - * UART to respond. IOW, at least 32 bytes of FIFO. - */ - if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) { - up->mcr &= ~UART_MCR_AFE; - if (termios->c_cflag & CRTSCTS) - up->mcr |= UART_MCR_AFE; - } - - /* - * Update the per-port timeout. - */ - uart_update_timeout(port, termios->c_cflag, baud); - - port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; - if (termios->c_iflag & INPCK) - port->read_status_mask |= UART_LSR_FE | UART_LSR_PE; - if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) - port->read_status_mask |= UART_LSR_BI; - - /* - * Characteres to ignore - */ - port->ignore_status_mask = 0; - if (termios->c_iflag & IGNPAR) - port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; - if (termios->c_iflag & IGNBRK) { - port->ignore_status_mask |= UART_LSR_BI; - /* - * If we're ignoring parity and break indicators, - * ignore overruns too (for real raw support). - */ - if (termios->c_iflag & IGNPAR) - port->ignore_status_mask |= UART_LSR_OE; - } - - /* - * ignore all characters if CREAD is not set - */ - if ((termios->c_cflag & CREAD) == 0) - port->ignore_status_mask |= UART_LSR_DR; - - /* - * CTS flow control flag and modem status interrupts - */ - up->ier &= ~UART_IER_MSI; - if (!(up->bugs & UART_BUG_NOMSR) && - UART_ENABLE_MS(&up->port, termios->c_cflag)) - up->ier |= UART_IER_MSI; - if (up->capabilities & UART_CAP_UUE) - up->ier |= UART_IER_UUE; - if (up->capabilities & UART_CAP_RTOIE) - up->ier |= UART_IER_RTOIE; - - serial_port_out(port, UART_IER, up->ier); - - if (up->capabilities & UART_CAP_EFR) { - unsigned char efr = 0; - /* - * TI16C752/Startech hardware flow control. FIXME: - * - TI16C752 requires control thresholds to be set. - * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled. - */ - if (termios->c_cflag & CRTSCTS) - efr |= UART_EFR_CTS; - - serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); - if (port->flags & UPF_EXAR_EFR) - serial_port_out(port, UART_XR_EFR, efr); - else - serial_port_out(port, UART_EFR, efr); - } - - serial8250_set_divisor(port, baud, quot, frac); + spin_lock_irqsave(&up->port.lock, flags); /* - * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR - * is written without DLAB set, this mode will be disabled. + * Must disable interrupts or else we risk racing with the interrupt + * based handler. */ - if (port->type == PORT_16750) - serial_port_out(port, UART_FCR, up->fcr); - - serial_port_out(port, UART_LCR, up->lcr); /* reset DLAB */ - if (port->type != PORT_16750) { - /* emulated UARTs (Lucent Venus 167x) need two steps */ - if (up->fcr & UART_FCR_ENABLE_FIFO) - serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO); - serial_port_out(port, UART_FCR, up->fcr); /* set fcr */ - } - serial8250_set_mctrl(port, port->mctrl); - spin_unlock_irqrestore(&port->lock, flags); - serial8250_rpm_put(up); - - /* Don't rewrite B0 */ - if (tty_termios_baud_rate(termios)) - tty_termios_encode_baud_rate(termios, baud, baud); -} -EXPORT_SYMBOL(serial8250_do_set_termios); - -static void -serial8250_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) -{ - if (port->set_termios) - port->set_termios(port, termios, old); - else - serial8250_do_set_termios(port, termios, old); -} - -static void -serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios) -{ - if (termios->c_line == N_PPS) { - port->flags |= UPF_HARDPPS_CD; - spin_lock_irq(&port->lock); - serial8250_enable_ms(port); - spin_unlock_irq(&port->lock); - } else { - port->flags &= ~UPF_HARDPPS_CD; - if (!UART_ENABLE_MS(port, termios->c_cflag)) { - spin_lock_irq(&port->lock); - serial8250_disable_ms(port); - spin_unlock_irq(&port->lock); - } + if (up->port.irq) { + ier = serial_in(up, UART_IER); + serial_out(up, UART_IER, 0); } -} + iir = serial_in(up, UART_IIR); -void serial8250_do_pm(struct uart_port *port, unsigned int state, - unsigned int oldstate) -{ - struct uart_8250_port *p = up_to_u8250p(port); + /* + * This should be a safe test for anyone who doesn't trust the + * IIR bits on their UART, but it's specifically designed for + * the "Diva" UART used on the management processor on many HP + * ia64 and parisc boxes. + */ + lsr = serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + if ((iir & UART_IIR_NO_INT) && (up->ier & UART_IER_THRI) && + (!uart_circ_empty(&up->port.state->xmit) || up->port.x_char) && + (lsr & UART_LSR_THRE)) { + iir &= ~(UART_IIR_ID | UART_IIR_NO_INT); + iir |= UART_IIR_THRI; + } - serial8250_set_sleep(p, state != 0); -} -EXPORT_SYMBOL(serial8250_do_pm); + if (!(iir & UART_IIR_NO_INT)) + serial8250_tx_chars(up); -static void -serial8250_pm(struct uart_port *port, unsigned int state, - unsigned int oldstate) -{ - if (port->pm) - port->pm(port, state, oldstate); - else - serial8250_do_pm(port, state, oldstate); -} + if (up->port.irq) + serial_out(up, UART_IER, ier); -static unsigned int serial8250_port_size(struct uart_8250_port *pt) -{ - if (pt->port.mapsize) - return pt->port.mapsize; - if (pt->port.iotype == UPIO_AU) { - if (pt->port.type == PORT_RT2880) - return 0x100; - return 0x1000; - } - if (is_omap1_8250(pt)) - return 0x16 << pt->port.regshift; + spin_unlock_irqrestore(&up->port.lock, flags); - return 8 << pt->port.regshift; + /* Standard timer interval plus 0.2s to keep the port running */ + mod_timer(&up->timer, + jiffies + uart_poll_timeout(&up->port) + HZ / 5); } -/* - * Resource handling. - */ -static int serial8250_request_std_resource(struct uart_8250_port *up) +static int univ8250_setup_irq(struct uart_8250_port *up) { - unsigned int size = serial8250_port_size(up); struct uart_port *port = &up->port; - int ret = 0; + int retval = 0; - switch (port->iotype) { - case UPIO_AU: - case UPIO_TSI: - case UPIO_MEM32: - case UPIO_MEM32BE: - case UPIO_MEM: - if (!port->mapbase) - break; + /* + * The above check will only give an accurate result the first time + * the port is opened so this value needs to be preserved. + */ + if (up->bugs & UART_BUG_THRE) { + pr_debug("ttyS%d - using backup timer\n", serial_index(port)); - if (!request_mem_region(port->mapbase, size, "serial")) { - ret = -EBUSY; - break; - } + up->timer.function = serial8250_backup_timeout; + up->timer.data = (unsigned long)up; + mod_timer(&up->timer, jiffies + + uart_poll_timeout(port) + HZ / 5); + } - if (port->flags & UPF_IOREMAP) { - port->membase = ioremap_nocache(port->mapbase, size); - if (!port->membase) { - release_mem_region(port->mapbase, size); - ret = -ENOMEM; - } - } - break; + /* + * If the "interrupt" for this port doesn't correspond with any + * hardware interrupt, we use a timer-based system. The original + * driver used to do this with IRQ0. + */ + if (!port->irq) { + up->timer.data = (unsigned long)up; + mod_timer(&up->timer, jiffies + uart_poll_timeout(port)); + } else + retval = serial_link_irq_chain(up); - case UPIO_HUB6: - case UPIO_PORT: - if (!request_region(port->iobase, size, "serial")) - ret = -EBUSY; - break; - } - return ret; + return retval; } -static void serial8250_release_std_resource(struct uart_8250_port *up) +static void univ8250_release_irq(struct uart_8250_port *up) { - unsigned int size = serial8250_port_size(up); struct uart_port *port = &up->port; - switch (port->iotype) { - case UPIO_AU: - case UPIO_TSI: - case UPIO_MEM32: - case UPIO_MEM32BE: - case UPIO_MEM: - if (!port->mapbase) - break; - - if (port->flags & UPF_IOREMAP) { - iounmap(port->membase); - port->membase = NULL; - } - - release_mem_region(port->mapbase, size); - break; - - case UPIO_HUB6: - case UPIO_PORT: - release_region(port->iobase, size); - break; - } + del_timer_sync(&up->timer); + up->timer.function = serial8250_timeout; + if (port->irq) + serial_unlink_irq_chain(up); } #ifdef CONFIG_SERIAL_8250_RSA @@ -2856,259 +396,6 @@ static void serial8250_release_rsa_resource(struct uart_8250_port *up) } #endif -static void serial8250_release_port(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - serial8250_release_std_resource(up); -} - -static int serial8250_request_port(struct uart_port *port) -{ - struct uart_8250_port *up = up_to_u8250p(port); - int ret; - - if (port->type == PORT_8250_CIR) - return -ENODEV; - - ret = serial8250_request_std_resource(up); - - return ret; -} - -static int fcr_get_rxtrig_bytes(struct uart_8250_port *up) -{ - const struct serial8250_config *conf_type = &uart_config[up->port.type]; - unsigned char bytes; - - bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)]; - - return bytes ? bytes : -EOPNOTSUPP; -} - -static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes) -{ - const struct serial8250_config *conf_type = &uart_config[up->port.type]; - int i; - - if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)]) - return -EOPNOTSUPP; - - for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) { - if (bytes < conf_type->rxtrig_bytes[i]) - /* Use the nearest lower value */ - return (--i) << UART_FCR_R_TRIG_SHIFT; - } - - return UART_FCR_R_TRIG_11; -} - -static int do_get_rxtrig(struct tty_port *port) -{ - struct uart_state *state = container_of(port, struct uart_state, port); - struct uart_port *uport = state->uart_port; - struct uart_8250_port *up = - container_of(uport, struct uart_8250_port, port); - - if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1) - return -EINVAL; - - return fcr_get_rxtrig_bytes(up); -} - -static int do_serial8250_get_rxtrig(struct tty_port *port) -{ - int rxtrig_bytes; - - mutex_lock(&port->mutex); - rxtrig_bytes = do_get_rxtrig(port); - mutex_unlock(&port->mutex); - - return rxtrig_bytes; -} - -static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev, - struct device_attribute *attr, char *buf) -{ - struct tty_port *port = dev_get_drvdata(dev); - int rxtrig_bytes; - - rxtrig_bytes = do_serial8250_get_rxtrig(port); - if (rxtrig_bytes < 0) - return rxtrig_bytes; - - return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes); -} - -static int do_set_rxtrig(struct tty_port *port, unsigned char bytes) -{ - struct uart_state *state = container_of(port, struct uart_state, port); - struct uart_port *uport = state->uart_port; - struct uart_8250_port *up = - container_of(uport, struct uart_8250_port, port); - int rxtrig; - - if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 || - up->fifo_bug) - return -EINVAL; - - rxtrig = bytes_to_fcr_rxtrig(up, bytes); - if (rxtrig < 0) - return rxtrig; - - serial8250_clear_fifos(up); - up->fcr &= ~UART_FCR_TRIGGER_MASK; - up->fcr |= (unsigned char)rxtrig; - serial_out(up, UART_FCR, up->fcr); - return 0; -} - -static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes) -{ - int ret; - - mutex_lock(&port->mutex); - ret = do_set_rxtrig(port, bytes); - mutex_unlock(&port->mutex); - - return ret; -} - -static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev, - struct device_attribute *attr, const char *buf, size_t count) -{ - struct tty_port *port = dev_get_drvdata(dev); - unsigned char bytes; - int ret; - - if (!count) - return -EINVAL; - - ret = kstrtou8(buf, 10, &bytes); - if (ret < 0) - return ret; - - ret = do_serial8250_set_rxtrig(port, bytes); - if (ret < 0) - return ret; - - return count; -} - -static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP, - serial8250_get_attr_rx_trig_bytes, - serial8250_set_attr_rx_trig_bytes); - -static struct attribute *serial8250_dev_attrs[] = { - &dev_attr_rx_trig_bytes.attr, - NULL, - }; - -static struct attribute_group serial8250_dev_attr_group = { - .attrs = serial8250_dev_attrs, - }; - -static void register_dev_spec_attr_grp(struct uart_8250_port *up) -{ - const struct serial8250_config *conf_type = &uart_config[up->port.type]; - - if (conf_type->rxtrig_bytes[0]) - up->port.attr_group = &serial8250_dev_attr_group; -} - -static void serial8250_config_port(struct uart_port *port, int flags) -{ - struct uart_8250_port *up = up_to_u8250p(port); - int ret; - - if (port->type == PORT_8250_CIR) - return; - - /* - * Find the region that we can probe for. This in turn - * tells us whether we can probe for the type of port. - */ - ret = serial8250_request_std_resource(up); - if (ret < 0) - return; - - if (port->iotype != up->cur_iotype) - set_io_from_upio(port); - - if (flags & UART_CONFIG_TYPE) - autoconfig(up); - - /* if access method is AU, it is a 16550 with a quirk */ - if (port->type == PORT_16550A && port->iotype == UPIO_AU) - up->bugs |= UART_BUG_NOMSR; - - /* HW bugs may trigger IRQ while IIR == NO_INT */ - if (port->type == PORT_TEGRA) - up->bugs |= UART_BUG_NOMSR; - - if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ) - autoconfig_irq(up); - - if (port->type == PORT_UNKNOWN) - serial8250_release_std_resource(up); - - /* Fixme: probably not the best place for this */ - if ((port->type == PORT_XR17V35X) || - (port->type == PORT_XR17D15X)) - port->handle_irq = exar_handle_irq; - - register_dev_spec_attr_grp(up); - up->fcr = uart_config[up->port.type].fcr; -} - -static int -serial8250_verify_port(struct uart_port *port, struct serial_struct *ser) -{ - if (ser->irq >= nr_irqs || ser->irq < 0 || - ser->baud_base < 9600 || ser->type < PORT_UNKNOWN || - ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS || - ser->type == PORT_STARTECH) - return -EINVAL; - return 0; -} - -static const char * -serial8250_type(struct uart_port *port) -{ - int type = port->type; - - if (type >= ARRAY_SIZE(uart_config)) - type = 0; - return uart_config[type].name; -} - -static const struct uart_ops serial8250_pops = { - .tx_empty = serial8250_tx_empty, - .set_mctrl = serial8250_set_mctrl, - .get_mctrl = serial8250_get_mctrl, - .stop_tx = serial8250_stop_tx, - .start_tx = serial8250_start_tx, - .throttle = serial8250_throttle, - .unthrottle = serial8250_unthrottle, - .stop_rx = serial8250_stop_rx, - .enable_ms = serial8250_enable_ms, - .break_ctl = serial8250_break_ctl, - .startup = serial8250_startup, - .shutdown = serial8250_shutdown, - .set_termios = serial8250_set_termios, - .set_ldisc = serial8250_set_ldisc, - .pm = serial8250_pm, - .type = serial8250_type, - .release_port = serial8250_release_port, - .request_port = serial8250_request_port, - .config_port = serial8250_config_port, - .verify_port = serial8250_verify_port, -#ifdef CONFIG_CONSOLE_POLL - .poll_get_char = serial8250_get_poll_char, - .poll_put_char = serial8250_put_poll_char, -#endif -}; - static const struct uart_ops *base_ops; static struct uart_ops univ8250_port_ops; @@ -3147,42 +434,6 @@ void serial8250_set_isa_configurator( } EXPORT_SYMBOL(serial8250_set_isa_configurator); -static void serial8250_init_port(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - - spin_lock_init(&port->lock); - port->ops = &serial8250_pops; - - up->cur_iotype = 0xFF; -} - -static void serial8250_set_defaults(struct uart_8250_port *up) -{ - struct uart_port *port = &up->port; - - if (up->port.flags & UPF_FIXED_TYPE) { - unsigned int type = up->port.type; - - if (!up->port.fifosize) - up->port.fifosize = uart_config[type].fifo_size; - if (!up->tx_loadsz) - up->tx_loadsz = uart_config[type].tx_loadsz; - if (!up->capabilities) - up->capabilities = uart_config[type].flags; - } - - set_io_from_upio(port); - - /* default dma handlers */ - if (up->dma) { - if (!up->dma->tx_dma) - up->dma->tx_dma = serial8250_tx_dma; - if (!up->dma->rx_dma) - up->dma->rx_dma = serial8250_rx_dma; - } -} - #ifdef CONFIG_SERIAL_8250_RSA static void univ8250_config_port(struct uart_port *port, int flags) @@ -3332,94 +583,6 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev) #ifdef CONFIG_SERIAL_8250_CONSOLE -static void serial8250_console_putchar(struct uart_port *port, int ch) -{ - struct uart_8250_port *up = up_to_u8250p(port); - - wait_for_xmitr(up, UART_LSR_THRE); - serial_port_out(port, UART_TX, ch); -} - -/* - * Print a string to the serial port trying not to disturb - * any possible real use of the port... - * - * The console_lock must be held when we get here. - */ -static void serial8250_console_write(struct uart_8250_port *up, const char *s, - unsigned int count, unsigned int loglevel) -{ - struct uart_port *port = &up->port; - unsigned long flags; - unsigned int ier; - int locked = 1; - - touch_nmi_watchdog(); - - serial8250_rpm_get(up); - - if (port->sysrq) - locked = 0; - else if (oops_in_progress) - locked = spin_trylock_irqsave(&port->lock, flags); - else - spin_lock_irqsave(&port->lock, flags); - - /* - * First save the IER then disable the interrupts - */ - ier = serial_port_in(port, UART_IER); - - if (up->capabilities & UART_CAP_UUE) - serial_port_out(port, UART_IER, UART_IER_UUE); - else - serial_port_out(port, UART_IER, 0); - - /* check scratch reg to see if port powered off during system sleep */ - if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) { - struct ktermios termios; - unsigned int baud, quot, frac = 0; - - termios.c_cflag = port->cons->cflag; - if (port->state->port.tty && termios.c_cflag == 0) - termios.c_cflag = port->state->port.tty->termios.c_cflag; - - baud = uart_get_baud_rate(port, &termios, NULL, - port->uartclk / 16 / 0xffff, - port->uartclk / 16); - quot = serial8250_get_divisor(up, baud, &frac); - - serial8250_set_divisor(port, baud, quot, frac); - serial_port_out(port, UART_LCR, up->lcr); - serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS); - - up->canary = 0; - } - - uart_console_write(port, s, count, serial8250_console_putchar); - - /* - * Finally, wait for transmitter to become empty - * and restore the IER - */ - wait_for_xmitr(up, BOTH_EMPTY); - serial_port_out(port, UART_IER, ier); - - /* - * The receive handling will happen properly because the - * receive ready bit will still be set; it is not cleared - * on read. However, modem control will not, we must - * call it if we have saved something in the saved flags - * while processing with interrupts off. - */ - if (up->msr_saved_flags) - serial8250_modem_status(up); - - if (locked) - spin_unlock_irqrestore(&port->lock, flags); - serial8250_rpm_put(up); -} - static void univ8250_console_write(struct console *co, const char *s, unsigned int count, unsigned int loglevel) { @@ -3428,39 +591,6 @@ static void univ8250_console_write(struct console *co, const char *s, serial8250_console_write(up, s, count, loglevel); } -static unsigned int probe_baud(struct uart_port *port) -{ - unsigned char lcr, dll, dlm; - unsigned int quot; - - lcr = serial_port_in(port, UART_LCR); - serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB); - dll = serial_port_in(port, UART_DLL); - dlm = serial_port_in(port, UART_DLM); - serial_port_out(port, UART_LCR, lcr); - - quot = (dlm << 8) | dll; - return (port->uartclk / 16) / quot; -} - -static int serial8250_console_setup(struct uart_port *port, char *options, bool probe) -{ - int baud = 9600; - int bits = 8; - int parity = 'n'; - int flow = 'n'; - - if (!port->iobase && !port->membase) - return -ENODEV; - - if (options) - uart_parse_options(options, &baud, &parity, &bits, &flow); - else if (probe) - baud = probe_baud(port); - - return uart_set_options(port, port->cons, baud, parity, bits, flow); -} - static int univ8250_console_setup(struct console *co, char *options) { struct uart_port *port; diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c index 21d01a491..e508939da 100644 --- a/drivers/tty/serial/8250/8250_dma.c +++ b/drivers/tty/serial/8250/8250_dma.c @@ -80,10 +80,6 @@ int serial8250_tx_dma(struct uart_8250_port *p) return 0; dma->tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); - if (dma->tx_size < p->port.fifosize) { - ret = -EINVAL; - goto err; - } desc = dmaengine_prep_slave_single(dma->txchan, dma->tx_addr + xmit->tail, diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c index d48b50641..06324f17a 100644 --- a/drivers/tty/serial/8250/8250_dw.c +++ b/drivers/tty/serial/8250/8250_dw.c @@ -56,7 +56,6 @@ struct dw8250_data { u8 usr_reg; - int last_mcr; int line; int msr_mask_on; int msr_mask_off; @@ -76,12 +75,6 @@ static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value) { struct dw8250_data *d = p->private_data; - /* If reading MSR, report CTS asserted when auto-CTS/RTS enabled */ - if (offset == UART_MSR && d->last_mcr & UART_MCR_AFE) { - value |= UART_MSR_CTS; - value &= ~UART_MSR_DCTS; - } - /* Override any modem control signals if needed */ if (offset == UART_MSR) { value |= d->msr_mask_on; @@ -101,11 +94,6 @@ static void dw8250_force_idle(struct uart_port *p) static void dw8250_serial_out(struct uart_port *p, int offset, int value) { - struct dw8250_data *d = p->private_data; - - if (offset == UART_MCR) - d->last_mcr = value; - writeb(value, p->membase + (offset << p->regshift)); /* Make sure LCR write wasn't ignored */ @@ -144,11 +132,6 @@ static unsigned int dw8250_serial_inq(struct uart_port *p, int offset) static void dw8250_serial_outq(struct uart_port *p, int offset, int value) { - struct dw8250_data *d = p->private_data; - - if (offset == UART_MCR) - d->last_mcr = value; - value &= 0xff; __raw_writeq(value, p->membase + (offset << p->regshift)); /* Read back to ensure register write ordering. */ @@ -175,11 +158,6 @@ static void dw8250_serial_outq(struct uart_port *p, int offset, int value) static void dw8250_serial_out32(struct uart_port *p, int offset, int value) { - struct dw8250_data *d = p->private_data; - - if (offset == UART_MCR) - d->last_mcr = value; - writel(value, p->membase + (offset << p->regshift)); /* Make sure LCR write wasn't ignored */ @@ -257,6 +235,11 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios, if (!ret) p->uartclk = rate; + + p->status &= ~UPSTAT_AUTOCTS; + if (termios->c_cflag & CRTSCTS) + p->status |= UPSTAT_AUTOCTS; + out: serial8250_do_set_termios(p, termios, old); } diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c index 6e0116bd9..4a2c3892c 100644 --- a/drivers/tty/serial/8250/8250_early.c +++ b/drivers/tty/serial/8250/8250_early.c @@ -35,7 +35,7 @@ #include #include -unsigned int __weak __init serial8250_early_in(struct uart_port *port, int offset) +static unsigned int __init serial8250_early_in(struct uart_port *port, int offset) { switch (port->iotype) { case UPIO_MEM: @@ -51,7 +51,7 @@ unsigned int __weak __init serial8250_early_in(struct uart_port *port, int offse } } -void __weak __init serial8250_early_out(struct uart_port *port, int offset, int value) +static void __init serial8250_early_out(struct uart_port *port, int offset, int value) { switch (port->iotype) { case UPIO_MEM: diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c index 5815e81b5..89474399a 100644 --- a/drivers/tty/serial/8250/8250_fintek.c +++ b/drivers/tty/serial/8250/8250_fintek.c @@ -17,18 +17,19 @@ #include #include "8250.h" -#define ADDR_PORT 0x4E -#define DATA_PORT 0x4F -#define ENTRY_KEY 0x77 +#define ADDR_PORT 0 +#define DATA_PORT 1 #define EXIT_KEY 0xAA #define CHIP_ID1 0x20 -#define CHIP_ID1_VAL 0x02 #define CHIP_ID2 0x21 -#define CHIP_ID2_VAL 0x16 +#define CHIP_ID_0 0x1602 +#define CHIP_ID_1 0x0501 #define VENDOR_ID1 0x23 #define VENDOR_ID1_VAL 0x19 #define VENDOR_ID2 0x24 #define VENDOR_ID2_VAL 0x34 +#define IO_ADDR1 0x61 +#define IO_ADDR2 0x60 #define LDN 0x7 #define RS485 0xF0 @@ -39,51 +40,49 @@ #define DRIVER_NAME "8250_fintek" -static int fintek_8250_enter_key(void){ +struct fintek_8250 { + u16 base_port; + u8 index; + u8 key; + long line; +}; + +static int fintek_8250_enter_key(u16 base_port, u8 key) +{ - if (!request_muxed_region(ADDR_PORT, 2, DRIVER_NAME)) + if (!request_muxed_region(base_port, 2, DRIVER_NAME)) return -EBUSY; - outb(ENTRY_KEY, ADDR_PORT); - outb(ENTRY_KEY, ADDR_PORT); + outb(key, base_port + ADDR_PORT); + outb(key, base_port + ADDR_PORT); return 0; } -static void fintek_8250_exit_key(void){ - - outb(EXIT_KEY, ADDR_PORT); - release_region(ADDR_PORT, 2); -} - -static int fintek_8250_get_index(resource_size_t base_addr) +static void fintek_8250_exit_key(u16 base_port) { - resource_size_t base[] = {0x3f8, 0x2f8, 0x3e8, 0x2e8}; - int i; - - for (i = 0; i < ARRAY_SIZE(base); i++) - if (base_addr == base[i]) - return i; - return -ENODEV; + outb(EXIT_KEY, base_port + ADDR_PORT); + release_region(base_port + ADDR_PORT, 2); } -static int fintek_8250_check_id(void) +static int fintek_8250_check_id(u16 base_port) { + u16 chip; - outb(CHIP_ID1, ADDR_PORT); - if (inb(DATA_PORT) != CHIP_ID1_VAL) + outb(VENDOR_ID1, base_port + ADDR_PORT); + if (inb(base_port + DATA_PORT) != VENDOR_ID1_VAL) return -ENODEV; - outb(CHIP_ID2, ADDR_PORT); - if (inb(DATA_PORT) != CHIP_ID2_VAL) + outb(VENDOR_ID2, base_port + ADDR_PORT); + if (inb(base_port + DATA_PORT) != VENDOR_ID2_VAL) return -ENODEV; - outb(VENDOR_ID1, ADDR_PORT); - if (inb(DATA_PORT) != VENDOR_ID1_VAL) - return -ENODEV; + outb(CHIP_ID1, base_port + ADDR_PORT); + chip = inb(base_port + DATA_PORT); + outb(CHIP_ID2, base_port + ADDR_PORT); + chip |= inb(base_port + DATA_PORT) << 8; - outb(VENDOR_ID2, ADDR_PORT); - if (inb(DATA_PORT) != VENDOR_ID2_VAL) + if (chip != CHIP_ID_0 && chip != CHIP_ID_1) return -ENODEV; return 0; @@ -93,9 +92,9 @@ static int fintek_8250_rs485_config(struct uart_port *port, struct serial_rs485 *rs485) { uint8_t config = 0; - int index = fintek_8250_get_index(port->iobase); + struct fintek_8250 *pdata = port->private_data; - if (index < 0) + if (!pdata) return -EINVAL; if (rs485->flags & SER_RS485_ENABLED) @@ -125,44 +124,84 @@ static int fintek_8250_rs485_config(struct uart_port *port, if (rs485->flags & SER_RS485_RTS_ON_SEND) config |= RTS_INVERT; - if (fintek_8250_enter_key()) + if (fintek_8250_enter_key(pdata->base_port, pdata->key)) return -EBUSY; - outb(LDN, ADDR_PORT); - outb(index, DATA_PORT); - outb(RS485, ADDR_PORT); - outb(config, DATA_PORT); - fintek_8250_exit_key(); + outb(LDN, pdata->base_port + ADDR_PORT); + outb(pdata->index, pdata->base_port + DATA_PORT); + outb(RS485, pdata->base_port + ADDR_PORT); + outb(config, pdata->base_port + DATA_PORT); + fintek_8250_exit_key(pdata->base_port); port->rs485 = *rs485; return 0; } +static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index) +{ + static const u16 addr[] = {0x4e, 0x2e}; + static const u8 keys[] = {0x77, 0xa0, 0x87, 0x67}; + int i, j, k; + + for (i = 0; i < ARRAY_SIZE(addr); i++) { + for (j = 0; j < ARRAY_SIZE(keys); j++) { + + if (fintek_8250_enter_key(addr[i], keys[j])) + continue; + if (fintek_8250_check_id(addr[i])) { + fintek_8250_exit_key(addr[i]); + continue; + } + + for (k = 0; k < 4; k++) { + u16 aux; + + outb(LDN, addr[i] + ADDR_PORT); + outb(k, addr[i] + DATA_PORT); + + outb(IO_ADDR1, addr[i] + ADDR_PORT); + aux = inb(addr[i] + DATA_PORT); + outb(IO_ADDR2, addr[i] + ADDR_PORT); + aux |= inb(addr[i] + DATA_PORT) << 8; + if (aux != io_address) + continue; + + fintek_8250_exit_key(addr[i]); + *key = keys[j]; + *index = k; + return addr[i]; + } + fintek_8250_exit_key(addr[i]); + } + } + + return -ENODEV; +} + static int fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) { - int line; struct uart_8250_port uart; - int ret; + struct fintek_8250 *pdata; + int base_port; + u8 key; + u8 index; if (!pnp_port_valid(dev, 0)) return -ENODEV; - if (fintek_8250_get_index(pnp_port_start(dev, 0)) < 0) + base_port = fintek_8250_base_port(pnp_port_start(dev, 0), &key, &index); + if (base_port < 0) return -ENODEV; - /* Enable configuration registers*/ - if (fintek_8250_enter_key()) - return -EBUSY; + memset(&uart, 0, sizeof(uart)); - /*Check ID*/ - ret = fintek_8250_check_id(); - fintek_8250_exit_key(); - if (ret) - return ret; + pdata = devm_kzalloc(&dev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return -ENOMEM; + uart.port.private_data = pdata; - memset(&uart, 0, sizeof(uart)); if (!pnp_irq_valid(dev, 0)) return -ENODEV; uart.port.irq = pnp_irq(dev, 0); @@ -176,40 +215,43 @@ fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) uart.port.uartclk = 1843200; uart.port.dev = &dev->dev; - line = serial8250_register_8250_port(&uart); - if (line < 0) + pdata->key = key; + pdata->base_port = base_port; + pdata->index = index; + pdata->line = serial8250_register_8250_port(&uart); + if (pdata->line < 0) return -ENODEV; - pnp_set_drvdata(dev, (void *)((long)line + 1)); + pnp_set_drvdata(dev, pdata); return 0; } static void fintek_8250_remove(struct pnp_dev *dev) { - long line = (long)pnp_get_drvdata(dev); + struct fintek_8250 *pdata = pnp_get_drvdata(dev); - if (line) - serial8250_unregister_port(line - 1); + if (pdata) + serial8250_unregister_port(pdata->line); } #ifdef CONFIG_PM static int fintek_8250_suspend(struct pnp_dev *dev, pm_message_t state) { - long line = (long)pnp_get_drvdata(dev); + struct fintek_8250 *pdata = pnp_get_drvdata(dev); - if (!line) + if (!pdata) return -ENODEV; - serial8250_suspend_port(line - 1); + serial8250_suspend_port(pdata->line); return 0; } static int fintek_8250_resume(struct pnp_dev *dev) { - long line = (long)pnp_get_drvdata(dev); + struct fintek_8250 *pdata = pnp_get_drvdata(dev); - if (!line) + if (!pdata) return -ENODEV; - serial8250_resume_port(line - 1); + serial8250_resume_port(pdata->line); return 0; } #else diff --git a/drivers/tty/serial/8250/8250_ingenic.c b/drivers/tty/serial/8250/8250_ingenic.c index 21bf81fe7..7c1e4be48 100644 --- a/drivers/tty/serial/8250/8250_ingenic.c +++ b/drivers/tty/serial/8250/8250_ingenic.c @@ -252,7 +252,6 @@ MODULE_DEVICE_TABLE(of, of_match); static struct platform_driver ingenic_uart_platform_driver = { .driver = { .name = "ingenic-uart", - .owner = THIS_MODULE, .of_match_table = of_match, }, .probe = ingenic_uart_probe, diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index b470df122..826c5c4a2 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -16,6 +16,7 @@ #include #include #include +#include #include #include #include @@ -32,6 +33,11 @@ #define UART_ERRATA_i202_MDR1_ACCESS (1 << 0) #define OMAP_UART_WER_HAS_TX_WAKEUP (1 << 1) #define OMAP_DMA_TX_KICK (1 << 2) +/* + * See Advisory 21 in AM437x errata SPRZ408B, updated April 2015. + * The same errata is applicable to AM335x and DRA7x processors too. + */ +#define UART_ERRATA_CLOCK_DISABLE (1 << 3) #define OMAP_UART_FCR_RX_TRIG 6 #define OMAP_UART_FCR_TX_TRIG 4 @@ -53,6 +59,12 @@ #define OMAP_UART_MVR_MAJ_SHIFT 8 #define OMAP_UART_MVR_MIN_MASK 0x3f +/* SYSC register bitmasks */ +#define OMAP_UART_SYSC_SOFTRESET (1 << 1) + +/* SYSS register bitmasks */ +#define OMAP_UART_SYSS_RESETDONE (1 << 0) + #define UART_TI752_TLR_TX 0 #define UART_TI752_TLR_RX 4 @@ -233,6 +245,15 @@ static void omap8250_update_scr(struct uart_8250_port *up, serial_out(up, UART_OMAP_SCR, priv->scr); } +static void omap8250_update_mdr1(struct uart_8250_port *up, + struct omap8250_priv *priv) +{ + if (priv->habit & UART_ERRATA_i202_MDR1_ACCESS) + omap_8250_mdr1_errataset(up, priv); + else + serial_out(up, UART_OMAP_MDR1, priv->mdr1); +} + static void omap8250_restore_regs(struct uart_8250_port *up) { struct omap8250_priv *priv = up->port.private_data; @@ -283,11 +304,9 @@ static void omap8250_restore_regs(struct uart_8250_port *up) serial_out(up, UART_XOFF1, priv->xoff); serial_out(up, UART_LCR, up->lcr); - /* need mode A for FCR */ - if (priv->habit & UART_ERRATA_i202_MDR1_ACCESS) - omap_8250_mdr1_errataset(up, priv); - else - serial_out(up, UART_OMAP_MDR1, priv->mdr1); + + omap8250_update_mdr1(up, priv); + up->port.ops->set_mctrl(&up->port, up->port.mctrl); } @@ -429,12 +448,9 @@ static void omap_8250_set_termios(struct uart_port *port, priv->efr |= UART_EFR_CTS; } else if (up->port.flags & UPF_SOFT_FLOW) { /* - * IXON Flag: - * Enable XON/XOFF flow control on input. - * Receiver compares XON1, XOFF1. + * OMAP rx s/w flow control is borked; the transmitter remains + * stuck off even if rx flow control is subsequently disabled */ - if (termios->c_iflag & IXON) - priv->efr |= OMAP_UART_SW_RX; /* * IXOFF Flag: @@ -445,15 +461,6 @@ static void omap_8250_set_termios(struct uart_port *port, up->port.status |= UPSTAT_AUTOXOFF; priv->efr |= OMAP_UART_SW_TX; } - - /* - * IXANY Flag: - * Enable any character to restart output. - * Operation resumes after receiving any - * character after recognition of the XOFF character - */ - if (termios->c_iflag & IXANY) - up->mcr |= UART_MCR_XONANY; } omap8250_restore_regs(up); @@ -531,14 +538,14 @@ static void omap_serial_fill_features_erratas(struct uart_8250_port *up, switch (revision) { case OMAP_UART_REV_46: - priv->habit = UART_ERRATA_i202_MDR1_ACCESS; + priv->habit |= UART_ERRATA_i202_MDR1_ACCESS; break; case OMAP_UART_REV_52: - priv->habit = UART_ERRATA_i202_MDR1_ACCESS | + priv->habit |= UART_ERRATA_i202_MDR1_ACCESS | OMAP_UART_WER_HAS_TX_WAKEUP; break; case OMAP_UART_REV_63: - priv->habit = UART_ERRATA_i202_MDR1_ACCESS | + priv->habit |= UART_ERRATA_i202_MDR1_ACCESS | OMAP_UART_WER_HAS_TX_WAKEUP; break; default: @@ -1061,6 +1068,20 @@ static int omap8250_no_handle_irq(struct uart_port *port) return 0; } +static const u8 am3352_habit = OMAP_DMA_TX_KICK | UART_ERRATA_CLOCK_DISABLE; +static const u8 am4372_habit = UART_ERRATA_CLOCK_DISABLE; + +static const struct of_device_id omap8250_dt_ids[] = { + { .compatible = "ti,omap2-uart" }, + { .compatible = "ti,omap3-uart" }, + { .compatible = "ti,omap4-uart" }, + { .compatible = "ti,am3352-uart", .data = &am3352_habit, }, + { .compatible = "ti,am4372-uart", .data = &am4372_habit, }, + { .compatible = "ti,dra742-uart", .data = &am4372_habit, }, + {}, +}; +MODULE_DEVICE_TABLE(of, omap8250_dt_ids); + static int omap8250_probe(struct platform_device *pdev) { struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -1125,11 +1146,17 @@ static int omap8250_probe(struct platform_device *pdev) up.port.unthrottle = omap_8250_unthrottle; if (pdev->dev.of_node) { + const struct of_device_id *id; + ret = of_alias_get_id(pdev->dev.of_node, "serial"); of_property_read_u32(pdev->dev.of_node, "clock-frequency", &up.port.uartclk); priv->wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1); + + id = of_match_device(of_match_ptr(omap8250_dt_ids), &pdev->dev); + if (id && id->data) + priv->habit |= *(u8 *)id->data; } else { ret = pdev->id; } @@ -1269,17 +1296,46 @@ static int omap8250_lost_context(struct uart_8250_port *up) { u32 val; - val = serial_in(up, UART_OMAP_MDR1); + val = serial_in(up, UART_OMAP_SCR); /* - * If we lose context, then MDR1 is set to its reset value which is - * UART_OMAP_MDR1_DISABLE. After set_termios() we set it either to 13x - * or 16x but never to disable again. + * If we lose context, then SCR is set to its reset value of zero. + * After set_termios() we set bit 3 of SCR (TX_EMPTY_CTL_IT) to 1, + * among other bits, to never set the register back to zero again. */ - if (val == UART_OMAP_MDR1_DISABLE) + if (!val) return 1; return 0; } +/* TODO: in future, this should happen via API in drivers/reset/ */ +static int omap8250_soft_reset(struct device *dev) +{ + struct omap8250_priv *priv = dev_get_drvdata(dev); + struct uart_8250_port *up = serial8250_get_port(priv->line); + int timeout = 100; + int sysc; + int syss; + + sysc = serial_in(up, UART_OMAP_SYSC); + + /* softreset the UART */ + sysc |= OMAP_UART_SYSC_SOFTRESET; + serial_out(up, UART_OMAP_SYSC, sysc); + + /* By experiments, 1us enough for reset complete on AM335x */ + do { + udelay(1); + syss = serial_in(up, UART_OMAP_SYSS); + } while (--timeout && !(syss & OMAP_UART_SYSS_RESETDONE)); + + if (!timeout) { + dev_err(dev, "timed out waiting for reset done\n"); + return -ETIMEDOUT; + } + + return 0; +} + static int omap8250_runtime_suspend(struct device *dev) { struct omap8250_priv *priv = dev_get_drvdata(dev); @@ -1297,7 +1353,18 @@ static int omap8250_runtime_suspend(struct device *dev) return -EBUSY; } - if (up->dma) + if (priv->habit & UART_ERRATA_CLOCK_DISABLE) { + int ret; + + ret = omap8250_soft_reset(dev); + if (ret) + return ret; + + /* Restore to UART mode after reset (for wakeup) */ + omap8250_update_mdr1(up, priv); + } + + if (up->dma && up->dma->rxchan) omap_8250_rx_dma(up, UART_IIR_RX_TIMEOUT); priv->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE; @@ -1322,7 +1389,7 @@ static int omap8250_runtime_resume(struct device *dev) if (loss_cntx) omap8250_restore_regs(up); - if (up->dma) + if (up->dma && up->dma->rxchan) omap_8250_rx_dma(up, 0); priv->latency = priv->calc_latency; @@ -1379,14 +1446,6 @@ static const struct dev_pm_ops omap8250_dev_pm_ops = { .complete = omap8250_complete, }; -static const struct of_device_id omap8250_dt_ids[] = { - { .compatible = "ti,omap2-uart" }, - { .compatible = "ti,omap3-uart" }, - { .compatible = "ti,omap4-uart" }, - {}, -}; -MODULE_DEVICE_TABLE(of, omap8250_dt_ids); - static struct platform_driver omap8250_platform_driver = { .driver = { .name = "omap8250", diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 46ddce479..68042dd1c 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -1417,6 +1417,10 @@ byt_set_termios(struct uart_port *p, struct ktermios *termios, reg |= BYT_PRV_CLK_EN | BYT_PRV_CLK_UPDATE; writel(reg, p->membase + BYT_PRV_CLK); + p->status &= ~UPSTAT_AUTOCTS; + if (termios->c_cflag & CRTSCTS) + p->status |= UPSTAT_AUTOCTS; + serial8250_do_set_termios(p, termios, old); } @@ -1685,11 +1689,65 @@ pci_brcm_trumanage_setup(struct serial_private *priv, return ret; } +/* RTS will control by MCR if this bit is 0 */ +#define FINTEK_RTS_CONTROL_BY_HW BIT(4) +/* only worked with FINTEK_RTS_CONTROL_BY_HW on */ +#define FINTEK_RTS_INVERT BIT(5) + +/* We should do proper H/W transceiver setting before change to RS485 mode */ +static int pci_fintek_rs485_config(struct uart_port *port, + struct serial_rs485 *rs485) +{ + u8 setting; + u8 *index = (u8 *) port->private_data; + struct pci_dev *pci_dev = container_of(port->dev, struct pci_dev, + dev); + + pci_read_config_byte(pci_dev, 0x40 + 8 * *index + 7, &setting); + + if (!rs485) + rs485 = &port->rs485; + else if (rs485->flags & SER_RS485_ENABLED) + memset(rs485->padding, 0, sizeof(rs485->padding)); + else + memset(rs485, 0, sizeof(*rs485)); + + /* F81504/508/512 not support RTS delay before or after send */ + rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND; + + if (rs485->flags & SER_RS485_ENABLED) { + /* Enable RTS H/W control mode */ + setting |= FINTEK_RTS_CONTROL_BY_HW; + + if (rs485->flags & SER_RS485_RTS_ON_SEND) { + /* RTS driving high on TX */ + setting &= ~FINTEK_RTS_INVERT; + } else { + /* RTS driving low on TX */ + setting |= FINTEK_RTS_INVERT; + } + + rs485->delay_rts_after_send = 0; + rs485->delay_rts_before_send = 0; + } else { + /* Disable RTS H/W control mode */ + setting &= ~(FINTEK_RTS_CONTROL_BY_HW | FINTEK_RTS_INVERT); + } + + pci_write_config_byte(pci_dev, 0x40 + 8 * *index + 7, setting); + + if (rs485 != &port->rs485) + port->rs485 = *rs485; + + return 0; +} + static int pci_fintek_setup(struct serial_private *priv, const struct pciserial_board *board, struct uart_8250_port *port, int idx) { struct pci_dev *pdev = priv->dev; + u8 *data; u8 config_base; u16 iobase; @@ -1702,6 +1760,15 @@ static int pci_fintek_setup(struct serial_private *priv, port->port.iotype = UPIO_PORT; port->port.iobase = iobase; + port->port.rs485_config = pci_fintek_rs485_config; + + data = devm_kzalloc(&pdev->dev, sizeof(u8), GFP_KERNEL); + if (!data) + return -ENOMEM; + + /* preserve index in PCI configuration space */ + *data = idx; + port->port.private_data = data; return 0; } @@ -1712,6 +1779,8 @@ static int pci_fintek_init(struct pci_dev *dev) u32 max_port, i; u32 bar_data[3]; u8 config_base; + struct serial_private *priv = pci_get_drvdata(dev); + struct uart_8250_port *port; switch (dev->device) { case 0x1104: /* 4 ports */ @@ -1752,6 +1821,19 @@ static int pci_fintek_init(struct pci_dev *dev) (u8)((iobase & 0xff00) >> 8)); pci_write_config_byte(dev, config_base + 0x06, dev->irq); + + if (priv) { + /* re-apply RS232/485 mode when + * pciserial_resume_ports() + */ + port = serial8250_get_port(priv->line[i]); + pci_fintek_rs485_config(&port->port, NULL); + } else { + /* First init without port data + * force init to RS232 Mode + */ + pci_write_config_byte(dev, config_base + 0x07, 0x01); + } } return max_port; diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c new file mode 100644 index 000000000..8bbb51fff --- /dev/null +++ b/drivers/tty/serial/8250/8250_port.c @@ -0,0 +1,2922 @@ +/* + * Base port operations for 8250/16550-type serial ports + * + * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. + * Split from 8250_core.c, Copyright (C) 2001 Russell King. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * A note about mapbase / membase + * + * mapbase is the physical address of the IO port. + * membase is an 'ioremapped' cookie. + */ + +#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +#include "8250.h" + +/* + * Debugging. + */ +#if 0 +#define DEBUG_AUTOCONF(fmt...) printk(fmt) +#else +#define DEBUG_AUTOCONF(fmt...) do { } while (0) +#endif + +#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) + +/* + * Here we define the default xmit fifo size used for each type of UART. + */ +static const struct serial8250_config uart_config[] = { + [PORT_UNKNOWN] = { + .name = "unknown", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_8250] = { + .name = "8250", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16450] = { + .name = "16450", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550] = { + .name = "16550", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16550A] = { + .name = "16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .rxtrig_bytes = {1, 4, 8, 14}, + .flags = UART_CAP_FIFO, + }, + [PORT_CIRRUS] = { + .name = "Cirrus", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16650] = { + .name = "ST16650", + .fifo_size = 1, + .tx_loadsz = 1, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16650V2] = { + .name = "ST16650V2", + .fifo_size = 32, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_00, + .rxtrig_bytes = {8, 16, 24, 28}, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16750] = { + .name = "TI16750", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | + UART_FCR7_64BYTE, + .rxtrig_bytes = {1, 16, 32, 56}, + .flags = UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE, + }, + [PORT_STARTECH] = { + .name = "Startech", + .fifo_size = 1, + .tx_loadsz = 1, + }, + [PORT_16C950] = { + .name = "16C950/954", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + /* UART_CAP_EFR breaks billionon CF bluetooth card. */ + .flags = UART_CAP_FIFO | UART_CAP_SLEEP, + }, + [PORT_16654] = { + .name = "ST16654", + .fifo_size = 64, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_10, + .rxtrig_bytes = {8, 16, 56, 60}, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_16850] = { + .name = "XR16850", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, + }, + [PORT_RSA] = { + .name = "RSA", + .fifo_size = 2048, + .tx_loadsz = 2048, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11, + .flags = UART_CAP_FIFO, + }, + [PORT_NS16550A] = { + .name = "NS16550A", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_NATSEMI, + }, + [PORT_XSCALE] = { + .name = "XScale", + .fifo_size = 32, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE, + }, + [PORT_OCTEON] = { + .name = "OCTEON", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO, + }, + [PORT_AR7] = { + .name = "AR7", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_U6_16550A] = { + .name = "U6_16550A", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_TEGRA] = { + .name = "Tegra", + .fifo_size = 32, + .tx_loadsz = 8, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 | + UART_FCR_T_TRIG_01, + .rxtrig_bytes = {1, 4, 8, 14}, + .flags = UART_CAP_FIFO | UART_CAP_RTOIE, + }, + [PORT_XR17D15X] = { + .name = "XR17D15X", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP, + }, + [PORT_XR17V35X] = { + .name = "XR17V35X", + .fifo_size = 256, + .tx_loadsz = 256, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 | + UART_FCR_T_TRIG_11, + .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP, + }, + [PORT_LPC3220] = { + .name = "LPC3220", + .fifo_size = 64, + .tx_loadsz = 32, + .fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO | + UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00, + .flags = UART_CAP_FIFO, + }, + [PORT_BRCM_TRUMANAGE] = { + .name = "TruManage", + .fifo_size = 1, + .tx_loadsz = 1024, + .flags = UART_CAP_HFIFO, + }, + [PORT_8250_CIR] = { + .name = "CIR port" + }, + [PORT_ALTR_16550_F32] = { + .name = "Altera 16550 FIFO32", + .fifo_size = 32, + .tx_loadsz = 32, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_ALTR_16550_F64] = { + .name = "Altera 16550 FIFO64", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, + [PORT_ALTR_16550_F128] = { + .name = "Altera 16550 FIFO128", + .fifo_size = 128, + .tx_loadsz = 128, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, +/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement +workaround of errata A-008006 which states that tx_loadsz should be +configured less than Maximum supported fifo bytes */ + [PORT_16550A_FSL64] = { + .name = "16550A_FSL64", + .fifo_size = 64, + .tx_loadsz = 63, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 | + UART_FCR7_64BYTE, + .flags = UART_CAP_FIFO, + }, + [PORT_RT2880] = { + .name = "Palmchip BK-3103", + .fifo_size = 16, + .tx_loadsz = 16, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .rxtrig_bytes = {1, 4, 8, 14}, + .flags = UART_CAP_FIFO, + }, +}; + +/* Uart divisor latch read */ +static int default_serial_dl_read(struct uart_8250_port *up) +{ + return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8; +} + +/* Uart divisor latch write */ +static void default_serial_dl_write(struct uart_8250_port *up, int value) +{ + serial_out(up, UART_DLL, value & 0xff); + serial_out(up, UART_DLM, value >> 8 & 0xff); +} + +#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) + +/* Au1x00/RT288x UART hardware has a weird register layout */ +static const s8 au_io_in_map[8] = { + 0, /* UART_RX */ + 2, /* UART_IER */ + 3, /* UART_IIR */ + 5, /* UART_LCR */ + 6, /* UART_MCR */ + 7, /* UART_LSR */ + 8, /* UART_MSR */ + -1, /* UART_SCR (unmapped) */ +}; + +static const s8 au_io_out_map[8] = { + 1, /* UART_TX */ + 2, /* UART_IER */ + 4, /* UART_FCR */ + 5, /* UART_LCR */ + 6, /* UART_MCR */ + -1, /* UART_LSR (unmapped) */ + -1, /* UART_MSR (unmapped) */ + -1, /* UART_SCR (unmapped) */ +}; + +static unsigned int au_serial_in(struct uart_port *p, int offset) +{ + if (offset >= ARRAY_SIZE(au_io_in_map)) + return UINT_MAX; + offset = au_io_in_map[offset]; + if (offset < 0) + return UINT_MAX; + return __raw_readl(p->membase + (offset << p->regshift)); +} + +static void au_serial_out(struct uart_port *p, int offset, int value) +{ + if (offset >= ARRAY_SIZE(au_io_out_map)) + return; + offset = au_io_out_map[offset]; + if (offset < 0) + return; + __raw_writel(value, p->membase + (offset << p->regshift)); +} + +/* Au1x00 haven't got a standard divisor latch */ +static int au_serial_dl_read(struct uart_8250_port *up) +{ + return __raw_readl(up->port.membase + 0x28); +} + +static void au_serial_dl_write(struct uart_8250_port *up, int value) +{ + __raw_writel(value, up->port.membase + 0x28); +} + +#endif + +static unsigned int hub6_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + outb(p->hub6 - 1 + offset, p->iobase); + return inb(p->iobase + 1); +} + +static void hub6_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + outb(p->hub6 - 1 + offset, p->iobase); + outb(value, p->iobase + 1); +} + +static unsigned int mem_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return readb(p->membase + offset); +} + +static void mem_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + writeb(value, p->membase + offset); +} + +static void mem32_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + writel(value, p->membase + offset); +} + +static unsigned int mem32_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return readl(p->membase + offset); +} + +static void mem32be_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + iowrite32be(value, p->membase + offset); +} + +static unsigned int mem32be_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return ioread32be(p->membase + offset); +} + +static unsigned int io_serial_in(struct uart_port *p, int offset) +{ + offset = offset << p->regshift; + return inb(p->iobase + offset); +} + +static void io_serial_out(struct uart_port *p, int offset, int value) +{ + offset = offset << p->regshift; + outb(value, p->iobase + offset); +} + +static int serial8250_default_handle_irq(struct uart_port *port); +static int exar_handle_irq(struct uart_port *port); + +static void set_io_from_upio(struct uart_port *p) +{ + struct uart_8250_port *up = up_to_u8250p(p); + + up->dl_read = default_serial_dl_read; + up->dl_write = default_serial_dl_write; + + switch (p->iotype) { + case UPIO_HUB6: + p->serial_in = hub6_serial_in; + p->serial_out = hub6_serial_out; + break; + + case UPIO_MEM: + p->serial_in = mem_serial_in; + p->serial_out = mem_serial_out; + break; + + case UPIO_MEM32: + p->serial_in = mem32_serial_in; + p->serial_out = mem32_serial_out; + break; + + case UPIO_MEM32BE: + p->serial_in = mem32be_serial_in; + p->serial_out = mem32be_serial_out; + break; + +#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) + case UPIO_AU: + p->serial_in = au_serial_in; + p->serial_out = au_serial_out; + up->dl_read = au_serial_dl_read; + up->dl_write = au_serial_dl_write; + break; +#endif + + default: + p->serial_in = io_serial_in; + p->serial_out = io_serial_out; + break; + } + /* Remember loaded iotype */ + up->cur_iotype = p->iotype; + p->handle_irq = serial8250_default_handle_irq; +} + +static void +serial_port_out_sync(struct uart_port *p, int offset, int value) +{ + switch (p->iotype) { + case UPIO_MEM: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_AU: + p->serial_out(p, offset, value); + p->serial_in(p, UART_LCR); /* safe, no side-effects */ + break; + default: + p->serial_out(p, offset, value); + } +} + +/* + * For the 16C950 + */ +static void serial_icr_write(struct uart_8250_port *up, int offset, int value) +{ + serial_out(up, UART_SCR, offset); + serial_out(up, UART_ICR, value); +} + +static unsigned int serial_icr_read(struct uart_8250_port *up, int offset) +{ + unsigned int value; + + serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD); + serial_out(up, UART_SCR, offset); + value = serial_in(up, UART_ICR); + serial_icr_write(up, UART_ACR, up->acr); + + return value; +} + +/* + * FIFO support. + */ +static void serial8250_clear_fifos(struct uart_8250_port *p) +{ + if (p->capabilities & UART_CAP_FIFO) { + serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_out(p, UART_FCR, 0); + } +} + +void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p) +{ + serial8250_clear_fifos(p); + serial_out(p, UART_FCR, p->fcr); +} +EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos); + +void serial8250_rpm_get(struct uart_8250_port *p) +{ + if (!(p->capabilities & UART_CAP_RPM)) + return; + pm_runtime_get_sync(p->port.dev); +} +EXPORT_SYMBOL_GPL(serial8250_rpm_get); + +void serial8250_rpm_put(struct uart_8250_port *p) +{ + if (!(p->capabilities & UART_CAP_RPM)) + return; + pm_runtime_mark_last_busy(p->port.dev); + pm_runtime_put_autosuspend(p->port.dev); +} +EXPORT_SYMBOL_GPL(serial8250_rpm_put); + +/* + * These two wrappers ensure that enable_runtime_pm_tx() can be called more than + * once and disable_runtime_pm_tx() will still disable RPM because the fifo is + * empty and the HW can idle again. + */ +static void serial8250_rpm_get_tx(struct uart_8250_port *p) +{ + unsigned char rpm_active; + + if (!(p->capabilities & UART_CAP_RPM)) + return; + + rpm_active = xchg(&p->rpm_tx_active, 1); + if (rpm_active) + return; + pm_runtime_get_sync(p->port.dev); +} + +static void serial8250_rpm_put_tx(struct uart_8250_port *p) +{ + unsigned char rpm_active; + + if (!(p->capabilities & UART_CAP_RPM)) + return; + + rpm_active = xchg(&p->rpm_tx_active, 0); + if (!rpm_active) + return; + pm_runtime_mark_last_busy(p->port.dev); + pm_runtime_put_autosuspend(p->port.dev); +} + +/* + * IER sleep support. UARTs which have EFRs need the "extended + * capability" bit enabled. Note that on XR16C850s, we need to + * reset LCR to write to IER. + */ +static void serial8250_set_sleep(struct uart_8250_port *p, int sleep) +{ + unsigned char lcr = 0, efr = 0; + /* + * Exar UARTs have a SLEEP register that enables or disables + * each UART to enter sleep mode separately. On the XR17V35x the + * register is accessible to each UART at the UART_EXAR_SLEEP + * offset but the UART channel may only write to the corresponding + * bit. + */ + serial8250_rpm_get(p); + if ((p->port.type == PORT_XR17V35X) || + (p->port.type == PORT_XR17D15X)) { + serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0); + goto out; + } + + if (p->capabilities & UART_CAP_SLEEP) { + if (p->capabilities & UART_CAP_EFR) { + lcr = serial_in(p, UART_LCR); + efr = serial_in(p, UART_EFR); + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(p, UART_EFR, UART_EFR_ECB); + serial_out(p, UART_LCR, 0); + } + serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0); + if (p->capabilities & UART_CAP_EFR) { + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(p, UART_EFR, efr); + serial_out(p, UART_LCR, lcr); + } + } +out: + serial8250_rpm_put(p); +} + +#ifdef CONFIG_SERIAL_8250_RSA +/* + * Attempts to turn on the RSA FIFO. Returns zero on failure. + * We set the port uart clock rate if we succeed. + */ +static int __enable_rsa(struct uart_8250_port *up) +{ + unsigned char mode; + int result; + + mode = serial_in(up, UART_RSA_MSR); + result = mode & UART_RSA_MSR_FIFO; + + if (!result) { + serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO); + mode = serial_in(up, UART_RSA_MSR); + result = mode & UART_RSA_MSR_FIFO; + } + + if (result) + up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16; + + return result; +} + +static void enable_rsa(struct uart_8250_port *up) +{ + if (up->port.type == PORT_RSA) { + if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) { + spin_lock_irq(&up->port.lock); + __enable_rsa(up); + spin_unlock_irq(&up->port.lock); + } + if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) + serial_out(up, UART_RSA_FRR, 0); + } +} + +/* + * Attempts to turn off the RSA FIFO. Returns zero on failure. + * It is unknown why interrupts were disabled in here. However, + * the caller is expected to preserve this behaviour by grabbing + * the spinlock before calling this function. + */ +static void disable_rsa(struct uart_8250_port *up) +{ + unsigned char mode; + int result; + + if (up->port.type == PORT_RSA && + up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) { + spin_lock_irq(&up->port.lock); + + mode = serial_in(up, UART_RSA_MSR); + result = !(mode & UART_RSA_MSR_FIFO); + + if (!result) { + serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO); + mode = serial_in(up, UART_RSA_MSR); + result = !(mode & UART_RSA_MSR_FIFO); + } + + if (result) + up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16; + spin_unlock_irq(&up->port.lock); + } +} +#endif /* CONFIG_SERIAL_8250_RSA */ + +/* + * This is a quickie test to see how big the FIFO is. + * It doesn't work at all the time, more's the pity. + */ +static int size_fifo(struct uart_8250_port *up) +{ + unsigned char old_fcr, old_mcr, old_lcr; + unsigned short old_dl; + int count; + + old_lcr = serial_in(up, UART_LCR); + serial_out(up, UART_LCR, 0); + old_fcr = serial_in(up, UART_FCR); + old_mcr = serial_in(up, UART_MCR); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_out(up, UART_MCR, UART_MCR_LOOP); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + old_dl = serial_dl_read(up); + serial_dl_write(up, 0x0001); + serial_out(up, UART_LCR, 0x03); + for (count = 0; count < 256; count++) + serial_out(up, UART_TX, count); + mdelay(20);/* FIXME - schedule_timeout */ + for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) && + (count < 256); count++) + serial_in(up, UART_RX); + serial_out(up, UART_FCR, old_fcr); + serial_out(up, UART_MCR, old_mcr); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + serial_dl_write(up, old_dl); + serial_out(up, UART_LCR, old_lcr); + + return count; +} + +/* + * Read UART ID using the divisor method - set DLL and DLM to zero + * and the revision will be in DLL and device type in DLM. We + * preserve the device state across this. + */ +static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p) +{ + unsigned char old_dll, old_dlm, old_lcr; + unsigned int id; + + old_lcr = serial_in(p, UART_LCR); + serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A); + + old_dll = serial_in(p, UART_DLL); + old_dlm = serial_in(p, UART_DLM); + + serial_out(p, UART_DLL, 0); + serial_out(p, UART_DLM, 0); + + id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8; + + serial_out(p, UART_DLL, old_dll); + serial_out(p, UART_DLM, old_dlm); + serial_out(p, UART_LCR, old_lcr); + + return id; +} + +/* + * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's. + * When this function is called we know it is at least a StarTech + * 16650 V2, but it might be one of several StarTech UARTs, or one of + * its clones. (We treat the broken original StarTech 16650 V1 as a + * 16550, and why not? Startech doesn't seem to even acknowledge its + * existence.) + * + * What evil have men's minds wrought... + */ +static void autoconfig_has_efr(struct uart_8250_port *up) +{ + unsigned int id1, id2, id3, rev; + + /* + * Everything with an EFR has SLEEP + */ + up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; + + /* + * First we check to see if it's an Oxford Semiconductor UART. + * + * If we have to do this here because some non-National + * Semiconductor clone chips lock up if you try writing to the + * LSR register (which serial_icr_read does) + */ + + /* + * Check for Oxford Semiconductor 16C950. + * + * EFR [4] must be set else this test fails. + * + * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca) + * claims that it's needed for 952 dual UART's (which are not + * recommended for new designs). + */ + up->acr = 0; + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, UART_LCR, 0x00); + id1 = serial_icr_read(up, UART_ID1); + id2 = serial_icr_read(up, UART_ID2); + id3 = serial_icr_read(up, UART_ID3); + rev = serial_icr_read(up, UART_REV); + + DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev); + + if (id1 == 0x16 && id2 == 0xC9 && + (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) { + up->port.type = PORT_16C950; + + /* + * Enable work around for the Oxford Semiconductor 952 rev B + * chip which causes it to seriously miscalculate baud rates + * when DLL is 0. + */ + if (id3 == 0x52 && rev == 0x01) + up->bugs |= UART_BUG_QUOT; + return; + } + + /* + * We check for a XR16C850 by setting DLL and DLM to 0, and then + * reading back DLL and DLM. The chip type depends on the DLM + * value read back: + * 0x10 - XR16C850 and the DLL contains the chip revision. + * 0x12 - XR16C2850. + * 0x14 - XR16C854. + */ + id1 = autoconfig_read_divisor_id(up); + DEBUG_AUTOCONF("850id=%04x ", id1); + + id2 = id1 >> 8; + if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) { + up->port.type = PORT_16850; + return; + } + + /* + * It wasn't an XR16C850. + * + * We distinguish between the '654 and the '650 by counting + * how many bytes are in the FIFO. I'm using this for now, + * since that's the technique that was sent to me in the + * serial driver update, but I'm not convinced this works. + * I've had problems doing this in the past. -TYT + */ + if (size_fifo(up) == 64) + up->port.type = PORT_16654; + else + up->port.type = PORT_16650V2; +} + +/* + * We detected a chip without a FIFO. Only two fall into + * this category - the original 8250 and the 16450. The + * 16450 has a scratch register (accessible with LCR=0) + */ +static void autoconfig_8250(struct uart_8250_port *up) +{ + unsigned char scratch, status1, status2; + + up->port.type = PORT_8250; + + scratch = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, 0xa5); + status1 = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, 0x5a); + status2 = serial_in(up, UART_SCR); + serial_out(up, UART_SCR, scratch); + + if (status1 == 0xa5 && status2 == 0x5a) + up->port.type = PORT_16450; +} + +static int broken_efr(struct uart_8250_port *up) +{ + /* + * Exar ST16C2550 "A2" devices incorrectly detect as + * having an EFR, and report an ID of 0x0201. See + * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html + */ + if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16) + return 1; + + return 0; +} + +/* + * We know that the chip has FIFOs. Does it have an EFR? The + * EFR is located in the same register position as the IIR and + * we know the top two bits of the IIR are currently set. The + * EFR should contain zero. Try to read the EFR. + */ +static void autoconfig_16550a(struct uart_8250_port *up) +{ + unsigned char status1, status2; + unsigned int iersave; + + up->port.type = PORT_16550A; + up->capabilities |= UART_CAP_FIFO; + + /* + * XR17V35x UARTs have an extra divisor register, DLD + * that gets enabled with when DLAB is set which will + * cause the device to incorrectly match and assign + * port type to PORT_16650. The EFR for this UART is + * found at offset 0x09. Instead check the Deice ID (DVID) + * register for a 2, 4 or 8 port UART. + */ + if (up->port.flags & UPF_EXAR_EFR) { + status1 = serial_in(up, UART_EXAR_DVID); + if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) { + DEBUG_AUTOCONF("Exar XR17V35x "); + up->port.type = PORT_XR17V35X; + up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP; + + return; + } + + } + + /* + * Check for presence of the EFR when DLAB is set. + * Only ST16C650V1 UARTs pass this test. + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + if (serial_in(up, UART_EFR) == 0) { + serial_out(up, UART_EFR, 0xA8); + if (serial_in(up, UART_EFR) != 0) { + DEBUG_AUTOCONF("EFRv1 "); + up->port.type = PORT_16650; + up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP; + } else { + serial_out(up, UART_LCR, 0); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR7_64BYTE); + status1 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, 0); + serial_out(up, UART_LCR, 0); + + if (status1 == 7) + up->port.type = PORT_16550A_FSL64; + else + DEBUG_AUTOCONF("Motorola 8xxx DUART "); + } + serial_out(up, UART_EFR, 0); + return; + } + + /* + * Maybe it requires 0xbf to be written to the LCR. + * (other ST16C650V2 UARTs, TI16C752A, etc) + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) { + DEBUG_AUTOCONF("EFRv2 "); + autoconfig_has_efr(up); + return; + } + + /* + * Check for a National Semiconductor SuperIO chip. + * Attempt to switch to bank 2, read the value of the LOOP bit + * from EXCR1. Switch back to bank 0, change it in MCR. Then + * switch back to bank 2, read it from EXCR1 again and check + * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2 + */ + serial_out(up, UART_LCR, 0); + status1 = serial_in(up, UART_MCR); + serial_out(up, UART_LCR, 0xE0); + status2 = serial_in(up, 0x02); /* EXCR1 */ + + if (!((status2 ^ status1) & UART_MCR_LOOP)) { + serial_out(up, UART_LCR, 0); + serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP); + serial_out(up, UART_LCR, 0xE0); + status2 = serial_in(up, 0x02); /* EXCR1 */ + serial_out(up, UART_LCR, 0); + serial_out(up, UART_MCR, status1); + + if ((status2 ^ status1) & UART_MCR_LOOP) { + unsigned short quot; + + serial_out(up, UART_LCR, 0xE0); + + quot = serial_dl_read(up); + quot <<= 3; + + if (ns16550a_goto_highspeed(up)) + serial_dl_write(up, quot); + + serial_out(up, UART_LCR, 0); + + up->port.uartclk = 921600*16; + up->port.type = PORT_NS16550A; + up->capabilities |= UART_NATSEMI; + return; + } + } + + /* + * No EFR. Try to detect a TI16750, which only sets bit 5 of + * the IIR when 64 byte FIFO mode is enabled when DLAB is set. + * Try setting it with and without DLAB set. Cheap clones + * set bit 5 without DLAB set. + */ + serial_out(up, UART_LCR, 0); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); + status1 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE); + status2 = serial_in(up, UART_IIR) >> 5; + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(up, UART_LCR, 0); + + DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2); + + if (status1 == 6 && status2 == 7) { + up->port.type = PORT_16750; + up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP; + return; + } + + /* + * Try writing and reading the UART_IER_UUE bit (b6). + * If it works, this is probably one of the Xscale platform's + * internal UARTs. + * We're going to explicitly set the UUE bit to 0 before + * trying to write and read a 1 just to make sure it's not + * already a 1 and maybe locked there before we even start start. + */ + iersave = serial_in(up, UART_IER); + serial_out(up, UART_IER, iersave & ~UART_IER_UUE); + if (!(serial_in(up, UART_IER) & UART_IER_UUE)) { + /* + * OK it's in a known zero state, try writing and reading + * without disturbing the current state of the other bits. + */ + serial_out(up, UART_IER, iersave | UART_IER_UUE); + if (serial_in(up, UART_IER) & UART_IER_UUE) { + /* + * It's an Xscale. + * We'll leave the UART_IER_UUE bit set to 1 (enabled). + */ + DEBUG_AUTOCONF("Xscale "); + up->port.type = PORT_XSCALE; + up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE; + return; + } + } else { + /* + * If we got here we couldn't force the IER_UUE bit to 0. + * Log it and continue. + */ + DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 "); + } + serial_out(up, UART_IER, iersave); + + /* + * Exar uarts have EFR in a weird location + */ + if (up->port.flags & UPF_EXAR_EFR) { + DEBUG_AUTOCONF("Exar XR17D15x "); + up->port.type = PORT_XR17D15X; + up->capabilities |= UART_CAP_AFE | UART_CAP_EFR | + UART_CAP_SLEEP; + + return; + } + + /* + * We distinguish between 16550A and U6 16550A by counting + * how many bytes are in the FIFO. + */ + if (up->port.type == PORT_16550A && size_fifo(up) == 64) { + up->port.type = PORT_U6_16550A; + up->capabilities |= UART_CAP_AFE; + } +} + +/* + * This routine is called by rs_init() to initialize a specific serial + * port. It determines what type of UART chip this serial port is + * using: 8250, 16450, 16550, 16550A. The important question is + * whether or not this UART is a 16550A or not, since this will + * determine whether or not we can use its FIFO features or not. + */ +static void autoconfig(struct uart_8250_port *up) +{ + unsigned char status1, scratch, scratch2, scratch3; + unsigned char save_lcr, save_mcr; + struct uart_port *port = &up->port; + unsigned long flags; + unsigned int old_capabilities; + + if (!port->iobase && !port->mapbase && !port->membase) + return; + + DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ", + serial_index(port), port->iobase, port->membase); + + /* + * We really do need global IRQs disabled here - we're going to + * be frobbing the chips IRQ enable register to see if it exists. + */ + spin_lock_irqsave(&port->lock, flags); + + up->capabilities = 0; + up->bugs = 0; + + if (!(port->flags & UPF_BUGGY_UART)) { + /* + * Do a simple existence test first; if we fail this, + * there's no point trying anything else. + * + * 0x80 is used as a nonsense port to prevent against + * false positives due to ISA bus float. The + * assumption is that 0x80 is a non-existent port; + * which should be safe since include/asm/io.h also + * makes this assumption. + * + * Note: this is safe as long as MCR bit 4 is clear + * and the device is in "PC" mode. + */ + scratch = serial_in(up, UART_IER); + serial_out(up, UART_IER, 0); +#ifdef __i386__ + outb(0xff, 0x080); +#endif + /* + * Mask out IER[7:4] bits for test as some UARTs (e.g. TL + * 16C754B) allow only to modify them if an EFR bit is set. + */ + scratch2 = serial_in(up, UART_IER) & 0x0f; + serial_out(up, UART_IER, 0x0F); +#ifdef __i386__ + outb(0, 0x080); +#endif + scratch3 = serial_in(up, UART_IER) & 0x0f; + serial_out(up, UART_IER, scratch); + if (scratch2 != 0 || scratch3 != 0x0F) { + /* + * We failed; there's nothing here + */ + spin_unlock_irqrestore(&port->lock, flags); + DEBUG_AUTOCONF("IER test failed (%02x, %02x) ", + scratch2, scratch3); + goto out; + } + } + + save_mcr = serial_in(up, UART_MCR); + save_lcr = serial_in(up, UART_LCR); + + /* + * Check to see if a UART is really there. Certain broken + * internal modems based on the Rockwell chipset fail this + * test, because they apparently don't implement the loopback + * test mode. So this test is skipped on the COM 1 through + * COM 4 ports. This *should* be safe, since no board + * manufacturer would be stupid enough to design a board + * that conflicts with COM 1-4 --- we hope! + */ + if (!(port->flags & UPF_SKIP_TEST)) { + serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A); + status1 = serial_in(up, UART_MSR) & 0xF0; + serial_out(up, UART_MCR, save_mcr); + if (status1 != 0x90) { + spin_unlock_irqrestore(&port->lock, flags); + DEBUG_AUTOCONF("LOOP test failed (%02x) ", + status1); + goto out; + } + } + + /* + * We're pretty sure there's a port here. Lets find out what + * type of port it is. The IIR top two bits allows us to find + * out if it's 8250 or 16450, 16550, 16550A or later. This + * determines what we test for next. + * + * We also initialise the EFR (if any) to zero for later. The + * EFR occupies the same register location as the FCR and IIR. + */ + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(up, UART_EFR, 0); + serial_out(up, UART_LCR, 0); + + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + scratch = serial_in(up, UART_IIR) >> 6; + + switch (scratch) { + case 0: + autoconfig_8250(up); + break; + case 1: + port->type = PORT_UNKNOWN; + break; + case 2: + port->type = PORT_16550; + break; + case 3: + autoconfig_16550a(up); + break; + } + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * Only probe for RSA ports if we got the region. + */ + if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA && + __enable_rsa(up)) + port->type = PORT_RSA; +#endif + + serial_out(up, UART_LCR, save_lcr); + + port->fifosize = uart_config[up->port.type].fifo_size; + old_capabilities = up->capabilities; + up->capabilities = uart_config[port->type].flags; + up->tx_loadsz = uart_config[port->type].tx_loadsz; + + if (port->type == PORT_UNKNOWN) + goto out_lock; + + /* + * Reset the UART. + */ +#ifdef CONFIG_SERIAL_8250_RSA + if (port->type == PORT_RSA) + serial_out(up, UART_RSA_FRR, 0); +#endif + serial_out(up, UART_MCR, save_mcr); + serial8250_clear_fifos(up); + serial_in(up, UART_RX); + if (up->capabilities & UART_CAP_UUE) + serial_out(up, UART_IER, UART_IER_UUE); + else + serial_out(up, UART_IER, 0); + +out_lock: + spin_unlock_irqrestore(&port->lock, flags); + if (up->capabilities != old_capabilities) { + printk(KERN_WARNING + "ttyS%d: detected caps %08x should be %08x\n", + serial_index(port), old_capabilities, + up->capabilities); + } +out: + DEBUG_AUTOCONF("iir=%d ", scratch); + DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name); +} + +static void autoconfig_irq(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + unsigned char save_mcr, save_ier; + unsigned char save_ICP = 0; + unsigned int ICP = 0; + unsigned long irqs; + int irq; + + if (port->flags & UPF_FOURPORT) { + ICP = (port->iobase & 0xfe0) | 0x1f; + save_ICP = inb_p(ICP); + outb_p(0x80, ICP); + inb_p(ICP); + } + + /* forget possible initially masked and pending IRQ */ + probe_irq_off(probe_irq_on()); + save_mcr = serial_in(up, UART_MCR); + save_ier = serial_in(up, UART_IER); + serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2); + + irqs = probe_irq_on(); + serial_out(up, UART_MCR, 0); + udelay(10); + if (port->flags & UPF_FOURPORT) { + serial_out(up, UART_MCR, + UART_MCR_DTR | UART_MCR_RTS); + } else { + serial_out(up, UART_MCR, + UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2); + } + serial_out(up, UART_IER, 0x0f); /* enable all intrs */ + serial_in(up, UART_LSR); + serial_in(up, UART_RX); + serial_in(up, UART_IIR); + serial_in(up, UART_MSR); + serial_out(up, UART_TX, 0xFF); + udelay(20); + irq = probe_irq_off(irqs); + + serial_out(up, UART_MCR, save_mcr); + serial_out(up, UART_IER, save_ier); + + if (port->flags & UPF_FOURPORT) + outb_p(save_ICP, ICP); + + port->irq = (irq > 0) ? irq : 0; +} + +static inline void __stop_tx(struct uart_8250_port *p) +{ + if (p->ier & UART_IER_THRI) { + p->ier &= ~UART_IER_THRI; + serial_out(p, UART_IER, p->ier); + serial8250_rpm_put_tx(p); + } +} + +static void serial8250_stop_tx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + __stop_tx(up); + + /* + * We really want to stop the transmitter from sending. + */ + if (port->type == PORT_16C950) { + up->acr |= UART_ACR_TXDIS; + serial_icr_write(up, UART_ACR, up->acr); + } + serial8250_rpm_put(up); +} + +static void serial8250_start_tx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get_tx(up); + + if (up->dma && !up->dma->tx_dma(up)) + return; + + if (!(up->ier & UART_IER_THRI)) { + up->ier |= UART_IER_THRI; + serial_port_out(port, UART_IER, up->ier); + + if (up->bugs & UART_BUG_TXEN) { + unsigned char lsr; + lsr = serial_in(up, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + if (lsr & UART_LSR_THRE) + serial8250_tx_chars(up); + } + } + + /* + * Re-enable the transmitter if we disabled it. + */ + if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) { + up->acr &= ~UART_ACR_TXDIS; + serial_icr_write(up, UART_ACR, up->acr); + } +} + +static void serial8250_throttle(struct uart_port *port) +{ + port->throttle(port); +} + +static void serial8250_unthrottle(struct uart_port *port) +{ + port->unthrottle(port); +} + +static void serial8250_stop_rx(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + + up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); + up->port.read_status_mask &= ~UART_LSR_DR; + serial_port_out(port, UART_IER, up->ier); + + serial8250_rpm_put(up); +} + +static void serial8250_disable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = + container_of(port, struct uart_8250_port, port); + + /* no MSR capabilities */ + if (up->bugs & UART_BUG_NOMSR) + return; + + up->ier &= ~UART_IER_MSI; + serial_port_out(port, UART_IER, up->ier); +} + +static void serial8250_enable_ms(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + /* no MSR capabilities */ + if (up->bugs & UART_BUG_NOMSR) + return; + + up->ier |= UART_IER_MSI; + + serial8250_rpm_get(up); + serial_port_out(port, UART_IER, up->ier); + serial8250_rpm_put(up); +} + +/* + * serial8250_rx_chars: processes according to the passed in LSR + * value, and returns the remaining LSR bits not handled + * by this Rx routine. + */ +unsigned char +serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr) +{ + struct uart_port *port = &up->port; + unsigned char ch; + int max_count = 256; + char flag; + + do { + if (likely(lsr & UART_LSR_DR)) + ch = serial_in(up, UART_RX); + else + /* + * Intel 82571 has a Serial Over Lan device that will + * set UART_LSR_BI without setting UART_LSR_DR when + * it receives a break. To avoid reading from the + * receive buffer without UART_LSR_DR bit set, we + * just force the read character to be 0 + */ + ch = 0; + + flag = TTY_NORMAL; + port->icount.rx++; + + lsr |= up->lsr_saved_flags; + up->lsr_saved_flags = 0; + + if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) { + if (lsr & UART_LSR_BI) { + lsr &= ~(UART_LSR_FE | UART_LSR_PE); + port->icount.brk++; + /* + * We do the SysRQ and SAK checking + * here because otherwise the break + * may get masked by ignore_status_mask + * or read_status_mask. + */ + if (uart_handle_break(port)) + goto ignore_char; + } else if (lsr & UART_LSR_PE) + port->icount.parity++; + else if (lsr & UART_LSR_FE) + port->icount.frame++; + if (lsr & UART_LSR_OE) + port->icount.overrun++; + + /* + * Mask off conditions which should be ignored. + */ + lsr &= port->read_status_mask; + + if (lsr & UART_LSR_BI) { + DEBUG_INTR("handling break...."); + flag = TTY_BREAK; + } else if (lsr & UART_LSR_PE) + flag = TTY_PARITY; + else if (lsr & UART_LSR_FE) + flag = TTY_FRAME; + } + if (uart_handle_sysrq_char(port, ch)) + goto ignore_char; + + uart_insert_char(port, lsr, UART_LSR_OE, ch, flag); + +ignore_char: + lsr = serial_in(up, UART_LSR); + } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0)); + spin_unlock(&port->lock); + tty_flip_buffer_push(&port->state->port); + spin_lock(&port->lock); + return lsr; +} +EXPORT_SYMBOL_GPL(serial8250_rx_chars); + +void serial8250_tx_chars(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + struct circ_buf *xmit = &port->state->xmit; + int count; + + if (port->x_char) { + serial_out(up, UART_TX, port->x_char); + port->icount.tx++; + port->x_char = 0; + return; + } + if (uart_tx_stopped(port)) { + serial8250_stop_tx(port); + return; + } + if (uart_circ_empty(xmit)) { + __stop_tx(up); + return; + } + + count = up->tx_loadsz; + do { + serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + if (uart_circ_empty(xmit)) + break; + if (up->capabilities & UART_CAP_HFIFO) { + if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) != + BOTH_EMPTY) + break; + } + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + DEBUG_INTR("THRE..."); + + /* + * With RPM enabled, we have to wait until the FIFO is empty before the + * HW can go idle. So we get here once again with empty FIFO and disable + * the interrupt and RPM in __stop_tx() + */ + if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM)) + __stop_tx(up); +} +EXPORT_SYMBOL_GPL(serial8250_tx_chars); + +/* Caller holds uart port lock */ +unsigned int serial8250_modem_status(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + unsigned int status = serial_in(up, UART_MSR); + + status |= up->msr_saved_flags; + up->msr_saved_flags = 0; + if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI && + port->state != NULL) { + if (status & UART_MSR_TERI) + port->icount.rng++; + if (status & UART_MSR_DDSR) + port->icount.dsr++; + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(port, status & UART_MSR_DCD); + if (status & UART_MSR_DCTS) + uart_handle_cts_change(port, status & UART_MSR_CTS); + + wake_up_interruptible(&port->state->port.delta_msr_wait); + } + + return status; +} +EXPORT_SYMBOL_GPL(serial8250_modem_status); + +/* + * This handles the interrupt from one port. + */ +int serial8250_handle_irq(struct uart_port *port, unsigned int iir) +{ + unsigned char status; + unsigned long flags; + struct uart_8250_port *up = up_to_u8250p(port); + int dma_err = 0; + + if (iir & UART_IIR_NO_INT) + return 0; + + spin_lock_irqsave(&port->lock, flags); + + status = serial_port_in(port, UART_LSR); + + DEBUG_INTR("status = %x...", status); + + if (status & (UART_LSR_DR | UART_LSR_BI)) { + if (up->dma) + dma_err = up->dma->rx_dma(up, iir); + + if (!up->dma || dma_err) + status = serial8250_rx_chars(up, status); + } + serial8250_modem_status(up); + if ((!up->dma || (up->dma && up->dma->tx_err)) && + (status & UART_LSR_THRE)) + serial8250_tx_chars(up); + + spin_unlock_irqrestore(&port->lock, flags); + return 1; +} +EXPORT_SYMBOL_GPL(serial8250_handle_irq); + +static int serial8250_default_handle_irq(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned int iir; + int ret; + + serial8250_rpm_get(up); + + iir = serial_port_in(port, UART_IIR); + ret = serial8250_handle_irq(port, iir); + + serial8250_rpm_put(up); + return ret; +} + +/* + * These Exar UARTs have an extra interrupt indicator that could + * fire for a few unimplemented interrupts. One of which is a + * wakeup event when coming out of sleep. Put this here just + * to be on the safe side that these interrupts don't go unhandled. + */ +static int exar_handle_irq(struct uart_port *port) +{ + unsigned char int0, int1, int2, int3; + unsigned int iir = serial_port_in(port, UART_IIR); + int ret; + + ret = serial8250_handle_irq(port, iir); + + if ((port->type == PORT_XR17V35X) || + (port->type == PORT_XR17D15X)) { + int0 = serial_port_in(port, 0x80); + int1 = serial_port_in(port, 0x81); + int2 = serial_port_in(port, 0x82); + int3 = serial_port_in(port, 0x83); + } + + return ret; +} + +static unsigned int serial8250_tx_empty(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + unsigned int lsr; + + serial8250_rpm_get(up); + + spin_lock_irqsave(&port->lock, flags); + lsr = serial_port_in(port, UART_LSR); + up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS; + spin_unlock_irqrestore(&port->lock, flags); + + serial8250_rpm_put(up); + + return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0; +} + +static unsigned int serial8250_get_mctrl(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned int status; + unsigned int ret; + + serial8250_rpm_get(up); + status = serial8250_modem_status(up); + serial8250_rpm_put(up); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char mcr = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr; + + serial_port_out(port, UART_MCR, mcr); +} +EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl); + +static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + if (port->set_mctrl) + port->set_mctrl(port, mctrl); + else + serial8250_do_set_mctrl(port, mctrl); +} + +static void serial8250_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + + serial8250_rpm_get(up); + spin_lock_irqsave(&port->lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + serial_port_out(port, UART_LCR, up->lcr); + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); +} + +/* + * Wait for transmitter & holding register to empty + */ +static void wait_for_xmitr(struct uart_8250_port *up, int bits) +{ + unsigned int status, tmout = 10000; + + /* Wait up to 10ms for the character(s) to be sent. */ + for (;;) { + status = serial_in(up, UART_LSR); + + up->lsr_saved_flags |= status & LSR_SAVE_FLAGS; + + if ((status & bits) == bits) + break; + if (--tmout == 0) + break; + udelay(1); + } + + /* Wait up to 1s for flow control if necessary */ + if (up->port.flags & UPF_CONS_FLOW) { + unsigned int tmout; + for (tmout = 1000000; tmout; tmout--) { + unsigned int msr = serial_in(up, UART_MSR); + up->msr_saved_flags |= msr & MSR_SAVE_FLAGS; + if (msr & UART_MSR_CTS) + break; + udelay(1); + touch_nmi_watchdog(); + } + } +} + +#ifdef CONFIG_CONSOLE_POLL +/* + * Console polling routines for writing and reading from the uart while + * in an interrupt or debug context. + */ + +static int serial8250_get_poll_char(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char lsr; + int status; + + serial8250_rpm_get(up); + + lsr = serial_port_in(port, UART_LSR); + + if (!(lsr & UART_LSR_DR)) { + status = NO_POLL_CHAR; + goto out; + } + + status = serial_port_in(port, UART_RX); +out: + serial8250_rpm_put(up); + return status; +} + + +static void serial8250_put_poll_char(struct uart_port *port, + unsigned char c) +{ + unsigned int ier; + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_rpm_get(up); + /* + * First save the IER then disable the interrupts + */ + ier = serial_port_in(port, UART_IER); + if (up->capabilities & UART_CAP_UUE) + serial_port_out(port, UART_IER, UART_IER_UUE); + else + serial_port_out(port, UART_IER, 0); + + wait_for_xmitr(up, BOTH_EMPTY); + /* + * Send the character out. + */ + serial_port_out(port, UART_TX, c); + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up, BOTH_EMPTY); + serial_port_out(port, UART_IER, ier); + serial8250_rpm_put(up); +} + +#endif /* CONFIG_CONSOLE_POLL */ + +int serial8250_do_startup(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + unsigned char lsr, iir; + int retval; + + if (port->type == PORT_8250_CIR) + return -ENODEV; + + if (!port->fifosize) + port->fifosize = uart_config[port->type].fifo_size; + if (!up->tx_loadsz) + up->tx_loadsz = uart_config[port->type].tx_loadsz; + if (!up->capabilities) + up->capabilities = uart_config[port->type].flags; + up->mcr = 0; + + if (port->iotype != up->cur_iotype) + set_io_from_upio(port); + + serial8250_rpm_get(up); + if (port->type == PORT_16C950) { + /* Wake up and initialize UART */ + up->acr = 0; + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + serial_port_out(port, UART_EFR, UART_EFR_ECB); + serial_port_out(port, UART_IER, 0); + serial_port_out(port, UART_LCR, 0); + serial_icr_write(up, UART_CSR, 0); /* Reset the UART */ + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + serial_port_out(port, UART_EFR, UART_EFR_ECB); + serial_port_out(port, UART_LCR, 0); + } + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * If this is an RSA port, see if we can kick it up to the + * higher speed clock. + */ + enable_rsa(up); +#endif + + if (port->type == PORT_XR17V35X) { + /* + * First enable access to IER [7:5], ISR [5:4], FCR [5:4], + * MCR [7:5] and MSR [7:0] + */ + serial_port_out(port, UART_XR_EFR, UART_EFR_ECB); + + /* + * Make sure all interrups are masked until initialization is + * complete and the FIFOs are cleared + */ + serial_port_out(port, UART_IER, 0); + } + + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + serial8250_clear_fifos(up); + + /* + * Clear the interrupt registers. + */ + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); + serial_port_in(port, UART_IIR); + serial_port_in(port, UART_MSR); + + /* + * At this point, there's no way the LSR could still be 0xff; + * if it is, then bail out, because there's likely no UART + * here. + */ + if (!(port->flags & UPF_BUGGY_UART) && + (serial_port_in(port, UART_LSR) == 0xff)) { + printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n", + serial_index(port)); + retval = -ENODEV; + goto out; + } + + /* + * For a XR16C850, we need to set the trigger levels + */ + if (port->type == PORT_16850) { + unsigned char fctr; + + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + + fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX); + serial_port_out(port, UART_FCTR, + fctr | UART_FCTR_TRGD | UART_FCTR_RX); + serial_port_out(port, UART_TRG, UART_TRG_96); + serial_port_out(port, UART_FCTR, + fctr | UART_FCTR_TRGD | UART_FCTR_TX); + serial_port_out(port, UART_TRG, UART_TRG_96); + + serial_port_out(port, UART_LCR, 0); + } + + if (port->irq) { + unsigned char iir1; + /* + * Test for UARTs that do not reassert THRE when the + * transmitter is idle and the interrupt has already + * been cleared. Real 16550s should always reassert + * this interrupt whenever the transmitter is idle and + * the interrupt is enabled. Delays are necessary to + * allow register changes to become visible. + */ + spin_lock_irqsave(&port->lock, flags); + if (up->port.irqflags & IRQF_SHARED) + disable_irq_nosync(port->irq); + + wait_for_xmitr(up, UART_LSR_THRE); + serial_port_out_sync(port, UART_IER, UART_IER_THRI); + udelay(1); /* allow THRE to set */ + iir1 = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + serial_port_out_sync(port, UART_IER, UART_IER_THRI); + udelay(1); /* allow a working UART time to re-assert THRE */ + iir = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + + if (port->irqflags & IRQF_SHARED) + enable_irq(port->irq); + spin_unlock_irqrestore(&port->lock, flags); + + /* + * If the interrupt is not reasserted, or we otherwise + * don't trust the iir, setup a timer to kick the UART + * on a regular basis. + */ + if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) || + up->port.flags & UPF_BUG_THRE) { + up->bugs |= UART_BUG_THRE; + } + } + + retval = up->ops->setup_irq(up); + if (retval) + goto out; + + /* + * Now, initialize the UART + */ + serial_port_out(port, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&port->lock, flags); + if (up->port.flags & UPF_FOURPORT) { + if (!up->port.irq) + up->port.mctrl |= TIOCM_OUT1; + } else + /* + * Most PC uarts need OUT2 raised to enable interrupts. + */ + if (port->irq) + up->port.mctrl |= TIOCM_OUT2; + + serial8250_set_mctrl(port, port->mctrl); + + /* Serial over Lan (SoL) hack: + Intel 8257x Gigabit ethernet chips have a + 16550 emulation, to be used for Serial Over Lan. + Those chips take a longer time than a normal + serial device to signalize that a transmission + data was queued. Due to that, the above test generally + fails. One solution would be to delay the reading of + iir. However, this is not reliable, since the timeout + is variable. So, let's just don't test if we receive + TX irq. This way, we'll never enable UART_BUG_TXEN. + */ + if (up->port.flags & UPF_NO_TXEN_TEST) + goto dont_test_tx_en; + + /* + * Do a quick test to see if we receive an + * interrupt when we enable the TX irq. + */ + serial_port_out(port, UART_IER, UART_IER_THRI); + lsr = serial_port_in(port, UART_LSR); + iir = serial_port_in(port, UART_IIR); + serial_port_out(port, UART_IER, 0); + + if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) { + if (!(up->bugs & UART_BUG_TXEN)) { + up->bugs |= UART_BUG_TXEN; + pr_debug("ttyS%d - enabling bad tx status workarounds\n", + serial_index(port)); + } + } else { + up->bugs &= ~UART_BUG_TXEN; + } + +dont_test_tx_en: + spin_unlock_irqrestore(&port->lock, flags); + + /* + * Clear the interrupt registers again for luck, and clear the + * saved flags to avoid getting false values from polling + * routines or the previous session. + */ + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); + serial_port_in(port, UART_IIR); + serial_port_in(port, UART_MSR); + up->lsr_saved_flags = 0; + up->msr_saved_flags = 0; + + /* + * Request DMA channels for both RX and TX. + */ + if (up->dma) { + retval = serial8250_request_dma(up); + if (retval) { + pr_warn_ratelimited("ttyS%d - failed to request DMA\n", + serial_index(port)); + up->dma = NULL; + } + } + + /* + * Set the IER shadow for rx interrupts but defer actual interrupt + * enable until after the FIFOs are enabled; otherwise, an already- + * active sender can swamp the interrupt handler with "too much work". + */ + up->ier = UART_IER_RLSI | UART_IER_RDI; + + if (port->flags & UPF_FOURPORT) { + unsigned int icp; + /* + * Enable interrupts on the AST Fourport board + */ + icp = (port->iobase & 0xfe0) | 0x01f; + outb_p(0x80, icp); + inb_p(icp); + } + retval = 0; +out: + serial8250_rpm_put(up); + return retval; +} +EXPORT_SYMBOL_GPL(serial8250_do_startup); + +static int serial8250_startup(struct uart_port *port) +{ + if (port->startup) + return port->startup(port); + return serial8250_do_startup(port); +} + +void serial8250_do_shutdown(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned long flags; + + serial8250_rpm_get(up); + /* + * Disable interrupts from this port + */ + up->ier = 0; + serial_port_out(port, UART_IER, 0); + + if (up->dma) + serial8250_release_dma(up); + + spin_lock_irqsave(&port->lock, flags); + if (port->flags & UPF_FOURPORT) { + /* reset interrupts on the AST Fourport board */ + inb((port->iobase & 0xfe0) | 0x1f); + port->mctrl |= TIOCM_OUT1; + } else + port->mctrl &= ~TIOCM_OUT2; + + serial8250_set_mctrl(port, port->mctrl); + spin_unlock_irqrestore(&port->lock, flags); + + /* + * Disable break condition and FIFOs + */ + serial_port_out(port, UART_LCR, + serial_port_in(port, UART_LCR) & ~UART_LCR_SBC); + serial8250_clear_fifos(up); + +#ifdef CONFIG_SERIAL_8250_RSA + /* + * Reset the RSA board back to 115kbps compat mode. + */ + disable_rsa(up); +#endif + + /* + * Read data port to reset things, and then unlink from + * the IRQ chain. + */ + serial_port_in(port, UART_RX); + serial8250_rpm_put(up); + + up->ops->release_irq(up); +} +EXPORT_SYMBOL_GPL(serial8250_do_shutdown); + +static void serial8250_shutdown(struct uart_port *port) +{ + if (port->shutdown) + port->shutdown(port); + else + serial8250_do_shutdown(port); +} + +/* + * XR17V35x UARTs have an extra fractional divisor register (DLD) + * Calculate divisor with extra 4-bit fractional portion + */ +static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up, + unsigned int baud, + unsigned int *frac) +{ + struct uart_port *port = &up->port; + unsigned int quot_16; + + quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud); + *frac = quot_16 & 0x0f; + + return quot_16 >> 4; +} + +static unsigned int serial8250_get_divisor(struct uart_8250_port *up, + unsigned int baud, + unsigned int *frac) +{ + struct uart_port *port = &up->port; + unsigned int quot; + + /* + * Handle magic divisors for baud rates above baud_base on + * SMSC SuperIO chips. + * + */ + if ((port->flags & UPF_MAGIC_MULTIPLIER) && + baud == (port->uartclk/4)) + quot = 0x8001; + else if ((port->flags & UPF_MAGIC_MULTIPLIER) && + baud == (port->uartclk/8)) + quot = 0x8002; + else if (up->port.type == PORT_XR17V35X) + quot = xr17v35x_get_divisor(up, baud, frac); + else + quot = uart_get_divisor(port, baud); + + /* + * Oxford Semi 952 rev B workaround + */ + if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0) + quot++; + + return quot; +} + +static unsigned char serial8250_compute_lcr(struct uart_8250_port *up, + tcflag_t c_cflag) +{ + unsigned char cval; + + switch (c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + if (c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (c_cflag & PARENB) { + cval |= UART_LCR_PARITY; + if (up->bugs & UART_BUG_PARITY) + up->fifo_bug = true; + } + if (!(c_cflag & PARODD)) + cval |= UART_LCR_EPAR; +#ifdef CMSPAR + if (c_cflag & CMSPAR) + cval |= UART_LCR_SPAR; +#endif + + return cval; +} + +static void serial8250_set_divisor(struct uart_port *port, unsigned int baud, + unsigned int quot, unsigned int quot_frac) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + /* Workaround to enable 115200 baud on OMAP1510 internal ports */ + if (is_omap1510_8250(up)) { + if (baud == 115200) { + quot = 1; + serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1); + } else + serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0); + } + + /* + * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2, + * otherwise just set DLAB + */ + if (up->capabilities & UART_NATSEMI) + serial_port_out(port, UART_LCR, 0xe0); + else + serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB); + + serial_dl_write(up, quot); + + /* XR17V35x UARTs have an extra fractional divisor register (DLD) */ + if (up->port.type == PORT_XR17V35X) + serial_port_out(port, 0x2, quot_frac); +} + +void +serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + struct uart_8250_port *up = up_to_u8250p(port); + unsigned char cval; + unsigned long flags; + unsigned int baud, quot, frac = 0; + + cval = serial8250_compute_lcr(up, termios->c_cflag); + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, + port->uartclk / 16 / 0xffff, + port->uartclk / 16); + quot = serial8250_get_divisor(up, baud, &frac); + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + serial8250_rpm_get(up); + spin_lock_irqsave(&port->lock, flags); + + up->lcr = cval; /* Save computed LCR */ + + if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) { + /* NOTE: If fifo_bug is not set, a user can set RX_trigger. */ + if ((baud < 2400 && !up->dma) || up->fifo_bug) { + up->fcr &= ~UART_FCR_TRIGGER_MASK; + up->fcr |= UART_FCR_TRIGGER_1; + } + } + + /* + * MCR-based auto flow control. When AFE is enabled, RTS will be + * deasserted when the receive FIFO contains more characters than + * the trigger, or the MCR RTS bit is cleared. In the case where + * the remote UART is not using CTS auto flow control, we must + * have sufficient FIFO entries for the latency of the remote + * UART to respond. IOW, at least 32 bytes of FIFO. + */ + if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) { + up->mcr &= ~UART_MCR_AFE; + if (termios->c_cflag & CRTSCTS) + up->mcr |= UART_MCR_AFE; + } + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + port->read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) + port->read_status_mask |= UART_LSR_BI; + + /* + * Characteres to ignore + */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + port->ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= UART_LSR_OE; + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + port->ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts + */ + up->ier &= ~UART_IER_MSI; + if (!(up->bugs & UART_BUG_NOMSR) && + UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + if (up->capabilities & UART_CAP_UUE) + up->ier |= UART_IER_UUE; + if (up->capabilities & UART_CAP_RTOIE) + up->ier |= UART_IER_RTOIE; + + serial_port_out(port, UART_IER, up->ier); + + if (up->capabilities & UART_CAP_EFR) { + unsigned char efr = 0; + /* + * TI16C752/Startech hardware flow control. FIXME: + * - TI16C752 requires control thresholds to be set. + * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled. + */ + if (termios->c_cflag & CRTSCTS) + efr |= UART_EFR_CTS; + + serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B); + if (port->flags & UPF_EXAR_EFR) + serial_port_out(port, UART_XR_EFR, efr); + else + serial_port_out(port, UART_EFR, efr); + } + + serial8250_set_divisor(port, baud, quot, frac); + + /* + * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR + * is written without DLAB set, this mode will be disabled. + */ + if (port->type == PORT_16750) + serial_port_out(port, UART_FCR, up->fcr); + + serial_port_out(port, UART_LCR, up->lcr); /* reset DLAB */ + if (port->type != PORT_16750) { + /* emulated UARTs (Lucent Venus 167x) need two steps */ + if (up->fcr & UART_FCR_ENABLE_FIFO) + serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_port_out(port, UART_FCR, up->fcr); /* set fcr */ + } + serial8250_set_mctrl(port, port->mctrl); + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); + + /* Don't rewrite B0 */ + if (tty_termios_baud_rate(termios)) + tty_termios_encode_baud_rate(termios, baud, baud); +} +EXPORT_SYMBOL(serial8250_do_set_termios); + +static void +serial8250_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + if (port->set_termios) + port->set_termios(port, termios, old); + else + serial8250_do_set_termios(port, termios, old); +} + +static void +serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios) +{ + if (termios->c_line == N_PPS) { + port->flags |= UPF_HARDPPS_CD; + spin_lock_irq(&port->lock); + serial8250_enable_ms(port); + spin_unlock_irq(&port->lock); + } else { + port->flags &= ~UPF_HARDPPS_CD; + if (!UART_ENABLE_MS(port, termios->c_cflag)) { + spin_lock_irq(&port->lock); + serial8250_disable_ms(port); + spin_unlock_irq(&port->lock); + } + } +} + + +void serial8250_do_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ + struct uart_8250_port *p = up_to_u8250p(port); + + serial8250_set_sleep(p, state != 0); +} +EXPORT_SYMBOL(serial8250_do_pm); + +static void +serial8250_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ + if (port->pm) + port->pm(port, state, oldstate); + else + serial8250_do_pm(port, state, oldstate); +} + +static unsigned int serial8250_port_size(struct uart_8250_port *pt) +{ + if (pt->port.mapsize) + return pt->port.mapsize; + if (pt->port.iotype == UPIO_AU) { + if (pt->port.type == PORT_RT2880) + return 0x100; + return 0x1000; + } + if (is_omap1_8250(pt)) + return 0x16 << pt->port.regshift; + + return 8 << pt->port.regshift; +} + +/* + * Resource handling. + */ +static int serial8250_request_std_resource(struct uart_8250_port *up) +{ + unsigned int size = serial8250_port_size(up); + struct uart_port *port = &up->port; + int ret = 0; + + switch (port->iotype) { + case UPIO_AU: + case UPIO_TSI: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_MEM: + if (!port->mapbase) + break; + + if (!request_mem_region(port->mapbase, size, "serial")) { + ret = -EBUSY; + break; + } + + if (port->flags & UPF_IOREMAP) { + port->membase = ioremap_nocache(port->mapbase, size); + if (!port->membase) { + release_mem_region(port->mapbase, size); + ret = -ENOMEM; + } + } + break; + + case UPIO_HUB6: + case UPIO_PORT: + if (!request_region(port->iobase, size, "serial")) + ret = -EBUSY; + break; + } + return ret; +} + +static void serial8250_release_std_resource(struct uart_8250_port *up) +{ + unsigned int size = serial8250_port_size(up); + struct uart_port *port = &up->port; + + switch (port->iotype) { + case UPIO_AU: + case UPIO_TSI: + case UPIO_MEM32: + case UPIO_MEM32BE: + case UPIO_MEM: + if (!port->mapbase) + break; + + if (port->flags & UPF_IOREMAP) { + iounmap(port->membase); + port->membase = NULL; + } + + release_mem_region(port->mapbase, size); + break; + + case UPIO_HUB6: + case UPIO_PORT: + release_region(port->iobase, size); + break; + } +} + +static void serial8250_release_port(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + serial8250_release_std_resource(up); +} + +static int serial8250_request_port(struct uart_port *port) +{ + struct uart_8250_port *up = up_to_u8250p(port); + int ret; + + if (port->type == PORT_8250_CIR) + return -ENODEV; + + ret = serial8250_request_std_resource(up); + + return ret; +} + +static int fcr_get_rxtrig_bytes(struct uart_8250_port *up) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + unsigned char bytes; + + bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)]; + + return bytes ? bytes : -EOPNOTSUPP; +} + +static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + int i; + + if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)]) + return -EOPNOTSUPP; + + for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) { + if (bytes < conf_type->rxtrig_bytes[i]) + /* Use the nearest lower value */ + return (--i) << UART_FCR_R_TRIG_SHIFT; + } + + return UART_FCR_R_TRIG_11; +} + +static int do_get_rxtrig(struct tty_port *port) +{ + struct uart_state *state = container_of(port, struct uart_state, port); + struct uart_port *uport = state->uart_port; + struct uart_8250_port *up = + container_of(uport, struct uart_8250_port, port); + + if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1) + return -EINVAL; + + return fcr_get_rxtrig_bytes(up); +} + +static int do_serial8250_get_rxtrig(struct tty_port *port) +{ + int rxtrig_bytes; + + mutex_lock(&port->mutex); + rxtrig_bytes = do_get_rxtrig(port); + mutex_unlock(&port->mutex); + + return rxtrig_bytes; +} + +static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct tty_port *port = dev_get_drvdata(dev); + int rxtrig_bytes; + + rxtrig_bytes = do_serial8250_get_rxtrig(port); + if (rxtrig_bytes < 0) + return rxtrig_bytes; + + return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes); +} + +static int do_set_rxtrig(struct tty_port *port, unsigned char bytes) +{ + struct uart_state *state = container_of(port, struct uart_state, port); + struct uart_port *uport = state->uart_port; + struct uart_8250_port *up = + container_of(uport, struct uart_8250_port, port); + int rxtrig; + + if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 || + up->fifo_bug) + return -EINVAL; + + rxtrig = bytes_to_fcr_rxtrig(up, bytes); + if (rxtrig < 0) + return rxtrig; + + serial8250_clear_fifos(up); + up->fcr &= ~UART_FCR_TRIGGER_MASK; + up->fcr |= (unsigned char)rxtrig; + serial_out(up, UART_FCR, up->fcr); + return 0; +} + +static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes) +{ + int ret; + + mutex_lock(&port->mutex); + ret = do_set_rxtrig(port, bytes); + mutex_unlock(&port->mutex); + + return ret; +} + +static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev, + struct device_attribute *attr, const char *buf, size_t count) +{ + struct tty_port *port = dev_get_drvdata(dev); + unsigned char bytes; + int ret; + + if (!count) + return -EINVAL; + + ret = kstrtou8(buf, 10, &bytes); + if (ret < 0) + return ret; + + ret = do_serial8250_set_rxtrig(port, bytes); + if (ret < 0) + return ret; + + return count; +} + +static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP, + serial8250_get_attr_rx_trig_bytes, + serial8250_set_attr_rx_trig_bytes); + +static struct attribute *serial8250_dev_attrs[] = { + &dev_attr_rx_trig_bytes.attr, + NULL, + }; + +static struct attribute_group serial8250_dev_attr_group = { + .attrs = serial8250_dev_attrs, + }; + +static void register_dev_spec_attr_grp(struct uart_8250_port *up) +{ + const struct serial8250_config *conf_type = &uart_config[up->port.type]; + + if (conf_type->rxtrig_bytes[0]) + up->port.attr_group = &serial8250_dev_attr_group; +} + +static void serial8250_config_port(struct uart_port *port, int flags) +{ + struct uart_8250_port *up = up_to_u8250p(port); + int ret; + + if (port->type == PORT_8250_CIR) + return; + + /* + * Find the region that we can probe for. This in turn + * tells us whether we can probe for the type of port. + */ + ret = serial8250_request_std_resource(up); + if (ret < 0) + return; + + if (port->iotype != up->cur_iotype) + set_io_from_upio(port); + + if (flags & UART_CONFIG_TYPE) + autoconfig(up); + + /* if access method is AU, it is a 16550 with a quirk */ + if (port->type == PORT_16550A && port->iotype == UPIO_AU) + up->bugs |= UART_BUG_NOMSR; + + /* HW bugs may trigger IRQ while IIR == NO_INT */ + if (port->type == PORT_TEGRA) + up->bugs |= UART_BUG_NOMSR; + + if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ) + autoconfig_irq(up); + + if (port->type == PORT_UNKNOWN) + serial8250_release_std_resource(up); + + /* Fixme: probably not the best place for this */ + if ((port->type == PORT_XR17V35X) || + (port->type == PORT_XR17D15X)) + port->handle_irq = exar_handle_irq; + + register_dev_spec_attr_grp(up); + up->fcr = uart_config[up->port.type].fcr; +} + +static int +serial8250_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + if (ser->irq >= nr_irqs || ser->irq < 0 || + ser->baud_base < 9600 || ser->type < PORT_UNKNOWN || + ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS || + ser->type == PORT_STARTECH) + return -EINVAL; + return 0; +} + +static const char * +serial8250_type(struct uart_port *port) +{ + int type = port->type; + + if (type >= ARRAY_SIZE(uart_config)) + type = 0; + return uart_config[type].name; +} + +static const struct uart_ops serial8250_pops = { + .tx_empty = serial8250_tx_empty, + .set_mctrl = serial8250_set_mctrl, + .get_mctrl = serial8250_get_mctrl, + .stop_tx = serial8250_stop_tx, + .start_tx = serial8250_start_tx, + .throttle = serial8250_throttle, + .unthrottle = serial8250_unthrottle, + .stop_rx = serial8250_stop_rx, + .enable_ms = serial8250_enable_ms, + .break_ctl = serial8250_break_ctl, + .startup = serial8250_startup, + .shutdown = serial8250_shutdown, + .set_termios = serial8250_set_termios, + .set_ldisc = serial8250_set_ldisc, + .pm = serial8250_pm, + .type = serial8250_type, + .release_port = serial8250_release_port, + .request_port = serial8250_request_port, + .config_port = serial8250_config_port, + .verify_port = serial8250_verify_port, +#ifdef CONFIG_CONSOLE_POLL + .poll_get_char = serial8250_get_poll_char, + .poll_put_char = serial8250_put_poll_char, +#endif +}; + +void serial8250_init_port(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + + spin_lock_init(&port->lock); + port->ops = &serial8250_pops; + + up->cur_iotype = 0xFF; +} +EXPORT_SYMBOL_GPL(serial8250_init_port); + +void serial8250_set_defaults(struct uart_8250_port *up) +{ + struct uart_port *port = &up->port; + + if (up->port.flags & UPF_FIXED_TYPE) { + unsigned int type = up->port.type; + + if (!up->port.fifosize) + up->port.fifosize = uart_config[type].fifo_size; + if (!up->tx_loadsz) + up->tx_loadsz = uart_config[type].tx_loadsz; + if (!up->capabilities) + up->capabilities = uart_config[type].flags; + } + + set_io_from_upio(port); + + /* default dma handlers */ + if (up->dma) { + if (!up->dma->tx_dma) + up->dma->tx_dma = serial8250_tx_dma; + if (!up->dma->rx_dma) + up->dma->rx_dma = serial8250_rx_dma; + } +} +EXPORT_SYMBOL_GPL(serial8250_set_defaults); + +#ifdef CONFIG_SERIAL_8250_CONSOLE + +static void serial8250_console_putchar(struct uart_port *port, int ch) +{ + struct uart_8250_port *up = up_to_u8250p(port); + + wait_for_xmitr(up, UART_LSR_THRE); + serial_port_out(port, UART_TX, ch); +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + * + * The console_lock must be held when we get here. + */ +void serial8250_console_write(struct uart_8250_port *up, const char *s, + unsigned int count, unsigned int loglevel) +{ + struct uart_port *port = &up->port; + unsigned long flags; + unsigned int ier; + int locked = 1; + + touch_nmi_watchdog(); + + serial8250_rpm_get(up); + + if (port->sysrq) + locked = 0; + else if (oops_in_progress) + locked = spin_trylock_irqsave(&port->lock, flags); + else + spin_lock_irqsave(&port->lock, flags); + + /* + * First save the IER then disable the interrupts + */ + ier = serial_port_in(port, UART_IER); + + if (up->capabilities & UART_CAP_UUE) + serial_port_out(port, UART_IER, UART_IER_UUE); + else + serial_port_out(port, UART_IER, 0); + + /* check scratch reg to see if port powered off during system sleep */ + if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) { + struct ktermios termios; + unsigned int baud, quot, frac = 0; + + termios.c_cflag = port->cons->cflag; + if (port->state->port.tty && termios.c_cflag == 0) + termios.c_cflag = port->state->port.tty->termios.c_cflag; + + baud = uart_get_baud_rate(port, &termios, NULL, + port->uartclk / 16 / 0xffff, + port->uartclk / 16); + quot = serial8250_get_divisor(up, baud, &frac); + + serial8250_set_divisor(port, baud, quot, frac); + serial_port_out(port, UART_LCR, up->lcr); + serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS); + + up->canary = 0; + } + + uart_console_write(port, s, count, serial8250_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up, BOTH_EMPTY); + serial_port_out(port, UART_IER, ier); + + /* + * The receive handling will happen properly because the + * receive ready bit will still be set; it is not cleared + * on read. However, modem control will not, we must + * call it if we have saved something in the saved flags + * while processing with interrupts off. + */ + if (up->msr_saved_flags) + serial8250_modem_status(up); + + if (locked) + spin_unlock_irqrestore(&port->lock, flags); + serial8250_rpm_put(up); +} + +static unsigned int probe_baud(struct uart_port *port) +{ + unsigned char lcr, dll, dlm; + unsigned int quot; + + lcr = serial_port_in(port, UART_LCR); + serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB); + dll = serial_port_in(port, UART_DLL); + dlm = serial_port_in(port, UART_DLM); + serial_port_out(port, UART_LCR, lcr); + + quot = (dlm << 8) | dll; + return (port->uartclk / 16) / quot; +} + +int serial8250_console_setup(struct uart_port *port, char *options, bool probe) +{ + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if (!port->iobase && !port->membase) + return -ENODEV; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + else if (probe) + baud = probe_baud(port); + + return uart_set_options(port, port->cons, baud, parity, bits, flow); +} + +#endif /* CONFIG_SERIAL_8250_CONSOLE */ + +MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile index 706295913..39c6d2277 100644 --- a/drivers/tty/serial/8250/Makefile +++ b/drivers/tty/serial/8250/Makefile @@ -2,10 +2,11 @@ # Makefile for the 8250 serial device drivers. # -obj-$(CONFIG_SERIAL_8250) += 8250.o +obj-$(CONFIG_SERIAL_8250) += 8250.o 8250_base.o 8250-y := 8250_core.o 8250-$(CONFIG_SERIAL_8250_PNP) += 8250_pnp.o -8250-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o +8250_base-y := 8250_port.o +8250_base-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 15b4079a3..687b1ea29 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -594,7 +594,7 @@ config SERIAL_IMX_CONSOLE config SERIAL_UARTLITE tristate "Xilinx uartlite serial port support" - depends on PPC32 || MICROBLAZE || MFD_TIMBERDALE || ARCH_ZYNQ + depends on HAS_IOMEM select SERIAL_CORE help Say Y here if you want to use the Xilinx uartlite serial controller. @@ -1067,6 +1067,7 @@ config SERIAL_ETRAXFS bool "ETRAX FS serial port support" depends on ETRAX_ARCH_V32 && OF select SERIAL_CORE + select SERIAL_MCTRL_GPIO if GPIOLIB config SERIAL_ETRAXFS_CONSOLE bool "ETRAX FS serial console support" @@ -1376,7 +1377,8 @@ config SERIAL_ALTERA_UART_CONSOLE config SERIAL_IFX6X60 tristate "SPI protocol driver for Infineon 6x60 modem (EXPERIMENTAL)" - depends on GPIOLIB && SPI && HAS_DMA + depends on GPIOLIB || COMPILE_TEST + depends on SPI && HAS_DMA help Support for the IFX6x60 modem devices on Intel MID platforms. diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index 40326b342..538ea03bc 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -56,6 +56,15 @@ /* Revisit: We should calculate this based on the actual port settings */ #define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */ +/* The minium number of data FIFOs should be able to contain */ +#define ATMEL_MIN_FIFO_SIZE 8 +/* + * These two offsets are substracted from the RX FIFO size to define the RTS + * high and low thresholds + */ +#define ATMEL_RTS_HIGH_OFFSET 16 +#define ATMEL_RTS_LOW_OFFSET 20 + #if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ #endif @@ -88,37 +97,6 @@ static void atmel_stop_rx(struct uart_port *port); #define ATMEL_ISR_PASS_LIMIT 256 -/* UART registers. CR is write-only, hence no GET macro */ -#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR) -#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR) -#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR) -#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER) -#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR) -#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR) -#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR) -#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR) -#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR) -#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR) -#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR) -#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR) -#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR) -#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME) -#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION) - - /* PDC registers */ -#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR) -#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR) - -#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR) -#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR) -#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR) -#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR) -#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR) - -#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR) -#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR) -#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR) - struct atmel_dma_buffer { unsigned char *buf; dma_addr_t dma_addr; @@ -166,12 +144,16 @@ struct atmel_uart_port { unsigned int irq_status; unsigned int irq_status_prev; unsigned int status_change; + unsigned int tx_len; struct circ_buf rx_ring; struct mctrl_gpios *gpios; int gpio_irq[UART_GPIO_MAX]; unsigned int tx_done_mask; + u32 fifo_size; + u32 rts_high; + u32 rts_low; bool ms_irq_enabled; bool is_usart; /* usart or uart */ struct timer_list uart_timer; /* uart timer */ @@ -212,6 +194,43 @@ to_atmel_uart_port(struct uart_port *uart) return container_of(uart, struct atmel_uart_port, uart); } +static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg) +{ + return __raw_readl(port->membase + reg); +} + +static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value) +{ + __raw_writel(value, port->membase + reg); +} + +#ifdef CONFIG_AVR32 + +/* AVR32 cannot handle 8 or 16bit I/O accesses but only 32bit I/O accesses */ +static inline u8 atmel_uart_read_char(struct uart_port *port) +{ + return __raw_readl(port->membase + ATMEL_US_RHR); +} + +static inline void atmel_uart_write_char(struct uart_port *port, u8 value) +{ + __raw_writel(value, port->membase + ATMEL_US_THR); +} + +#else + +static inline u8 atmel_uart_read_char(struct uart_port *port) +{ + return __raw_readb(port->membase + ATMEL_US_RHR); +} + +static inline void atmel_uart_write_char(struct uart_port *port, u8 value) +{ + __raw_writeb(value, port->membase + ATMEL_US_THR); +} + +#endif + #ifdef CONFIG_SERIAL_ATMEL_PDC static bool atmel_use_pdc_rx(struct uart_port *port) { @@ -257,7 +276,7 @@ static unsigned int atmel_get_lines_status(struct uart_port *port) struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); unsigned int status, ret = 0; - status = UART_GET_CSR(port); + status = atmel_uart_readl(port, ATMEL_US_CSR); mctrl_gpio_get(atmel_port->gpios, &ret); @@ -304,9 +323,9 @@ static int atmel_config_rs485(struct uart_port *port, unsigned int mode; /* Disable interrupts */ - UART_PUT_IDR(port, atmel_port->tx_done_mask); + atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); - mode = UART_GET_MR(port); + mode = atmel_uart_readl(port, ATMEL_US_MR); /* Resetting serial mode to RS232 (0x0) */ mode &= ~ATMEL_US_USMODE; @@ -316,7 +335,8 @@ static int atmel_config_rs485(struct uart_port *port, if (rs485conf->flags & SER_RS485_ENABLED) { dev_dbg(port->dev, "Setting UART to RS485\n"); atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; - UART_PUT_TTGR(port, rs485conf->delay_rts_after_send); + atmel_uart_writel(port, ATMEL_US_TTGR, + rs485conf->delay_rts_after_send); mode |= ATMEL_US_USMODE_RS485; } else { dev_dbg(port->dev, "Setting UART to RS232\n"); @@ -326,10 +346,10 @@ static int atmel_config_rs485(struct uart_port *port, else atmel_port->tx_done_mask = ATMEL_US_TXRDY; } - UART_PUT_MR(port, mode); + atmel_uart_writel(port, ATMEL_US_MR, mode); /* Enable interrupts */ - UART_PUT_IER(port, atmel_port->tx_done_mask); + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); return 0; } @@ -339,7 +359,9 @@ static int atmel_config_rs485(struct uart_port *port, */ static u_int atmel_tx_empty(struct uart_port *port) { - return (UART_GET_CSR(port) & ATMEL_US_TXEMPTY) ? TIOCSER_TEMT : 0; + return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ? + TIOCSER_TEMT : + 0; } /* @@ -348,13 +370,14 @@ static u_int atmel_tx_empty(struct uart_port *port) static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) { unsigned int control = 0; - unsigned int mode = UART_GET_MR(port); + unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR); unsigned int rts_paused, rts_ready; struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); /* override mode to RS485 if needed, otherwise keep the current mode */ if (port->rs485.flags & SER_RS485_ENABLED) { - UART_PUT_TTGR(port, port->rs485.delay_rts_after_send); + atmel_uart_writel(port, ATMEL_US_TTGR, + port->rs485.delay_rts_after_send); mode &= ~ATMEL_US_USMODE; mode |= ATMEL_US_USMODE_RS485; } @@ -384,7 +407,7 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) else control |= ATMEL_US_DTRDIS; - UART_PUT_CR(port, control); + atmel_uart_writel(port, ATMEL_US_CR, control); mctrl_gpio_set(atmel_port->gpios, mctrl); @@ -395,7 +418,7 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) else mode |= ATMEL_US_CHMODE_NORMAL; - UART_PUT_MR(port, mode); + atmel_uart_writel(port, ATMEL_US_MR, mode); } /* @@ -406,7 +429,7 @@ static u_int atmel_get_mctrl(struct uart_port *port) struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); unsigned int ret = 0, status; - status = UART_GET_CSR(port); + status = atmel_uart_readl(port, ATMEL_US_CSR); /* * The control signals are active low. @@ -432,10 +455,10 @@ static void atmel_stop_tx(struct uart_port *port) if (atmel_use_pdc_tx(port)) { /* disable PDC transmit */ - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); } /* Disable interrupts */ - UART_PUT_IDR(port, atmel_port->tx_done_mask); + atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); if ((port->rs485.flags & SER_RS485_ENABLED) && !(port->rs485.flags & SER_RS485_RX_DURING_TX)) @@ -450,7 +473,7 @@ static void atmel_start_tx(struct uart_port *port) struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); if (atmel_use_pdc_tx(port)) { - if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN) + if (atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN) /* The transmitter is already running. Yes, we really need this.*/ return; @@ -460,10 +483,10 @@ static void atmel_start_tx(struct uart_port *port) atmel_stop_rx(port); /* re-enable PDC transmit */ - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); } /* Enable interrupts */ - UART_PUT_IER(port, atmel_port->tx_done_mask); + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); } /* @@ -471,17 +494,19 @@ static void atmel_start_tx(struct uart_port *port) */ static void atmel_start_rx(struct uart_port *port) { - UART_PUT_CR(port, ATMEL_US_RSTSTA); /* reset status and receiver */ + /* reset status and receiver */ + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); - UART_PUT_CR(port, ATMEL_US_RXEN); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN); if (atmel_use_pdc_rx(port)) { /* enable PDC controller */ - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | - port->read_status_mask); - UART_PUT_PTCR(port, ATMEL_PDC_RXTEN); + atmel_uart_writel(port, ATMEL_US_IER, + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | + port->read_status_mask); + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); } else { - UART_PUT_IER(port, ATMEL_US_RXRDY); + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY); } } @@ -490,15 +515,16 @@ static void atmel_start_rx(struct uart_port *port) */ static void atmel_stop_rx(struct uart_port *port) { - UART_PUT_CR(port, ATMEL_US_RXDIS); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS); if (atmel_use_pdc_rx(port)) { /* disable PDC receive */ - UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS); - UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | - port->read_status_mask); + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS); + atmel_uart_writel(port, ATMEL_US_IDR, + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | + port->read_status_mask); } else { - UART_PUT_IDR(port, ATMEL_US_RXRDY); + atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY); } } @@ -538,7 +564,7 @@ static void atmel_enable_ms(struct uart_port *port) else ier |= ATMEL_US_DCDIC; - UART_PUT_IER(port, ier); + atmel_uart_writel(port, ATMEL_US_IER, ier); } /* @@ -577,7 +603,7 @@ static void atmel_disable_ms(struct uart_port *port) else idr |= ATMEL_US_DCDIC; - UART_PUT_IDR(port, idr); + atmel_uart_writel(port, ATMEL_US_IDR, idr); } /* @@ -586,9 +612,11 @@ static void atmel_disable_ms(struct uart_port *port) static void atmel_break_ctl(struct uart_port *port, int break_state) { if (break_state != 0) - UART_PUT_CR(port, ATMEL_US_STTBRK); /* start break */ + /* start break */ + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK); else - UART_PUT_CR(port, ATMEL_US_STPBRK); /* stop break */ + /* stop break */ + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK); } /* @@ -622,7 +650,7 @@ atmel_buffer_rx_char(struct uart_port *port, unsigned int status, static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status) { /* clear error */ - UART_PUT_CR(port, ATMEL_US_RSTSTA); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); if (status & ATMEL_US_RXBRK) { /* ignore side-effect */ @@ -645,9 +673,9 @@ static void atmel_rx_chars(struct uart_port *port) struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); unsigned int status, ch; - status = UART_GET_CSR(port); + status = atmel_uart_readl(port, ATMEL_US_CSR); while (status & ATMEL_US_RXRDY) { - ch = UART_GET_CHAR(port); + ch = atmel_uart_read_char(port); /* * note that the error handling code is @@ -658,12 +686,13 @@ static void atmel_rx_chars(struct uart_port *port) || atmel_port->break_active)) { /* clear error */ - UART_PUT_CR(port, ATMEL_US_RSTSTA); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); if (status & ATMEL_US_RXBRK && !atmel_port->break_active) { atmel_port->break_active = 1; - UART_PUT_IER(port, ATMEL_US_RXBRK); + atmel_uart_writel(port, ATMEL_US_IER, + ATMEL_US_RXBRK); } else { /* * This is either the end-of-break @@ -672,14 +701,15 @@ static void atmel_rx_chars(struct uart_port *port) * being set. In both cases, the next * RXBRK will indicate start-of-break. */ - UART_PUT_IDR(port, ATMEL_US_RXBRK); + atmel_uart_writel(port, ATMEL_US_IDR, + ATMEL_US_RXBRK); status &= ~ATMEL_US_RXBRK; atmel_port->break_active = 0; } } atmel_buffer_rx_char(port, status, ch); - status = UART_GET_CSR(port); + status = atmel_uart_readl(port, ATMEL_US_CSR); } tasklet_schedule(&atmel_port->tasklet); @@ -694,16 +724,18 @@ static void atmel_tx_chars(struct uart_port *port) struct circ_buf *xmit = &port->state->xmit; struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); - if (port->x_char && UART_GET_CSR(port) & atmel_port->tx_done_mask) { - UART_PUT_CHAR(port, port->x_char); + if (port->x_char && + (atmel_uart_readl(port, ATMEL_US_CSR) & atmel_port->tx_done_mask)) { + atmel_uart_write_char(port, port->x_char); port->icount.tx++; port->x_char = 0; } if (uart_circ_empty(xmit) || uart_tx_stopped(port)) return; - while (UART_GET_CSR(port) & atmel_port->tx_done_mask) { - UART_PUT_CHAR(port, xmit->buf[xmit->tail]); + while (atmel_uart_readl(port, ATMEL_US_CSR) & + atmel_port->tx_done_mask) { + atmel_uart_write_char(port, xmit->buf[xmit->tail]); xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); port->icount.tx++; if (uart_circ_empty(xmit)) @@ -715,7 +747,8 @@ static void atmel_tx_chars(struct uart_port *port) if (!uart_circ_empty(xmit)) /* Enable interrupts */ - UART_PUT_IER(port, atmel_port->tx_done_mask); + atmel_uart_writel(port, ATMEL_US_IER, + atmel_port->tx_done_mask); } static void atmel_complete_tx_dma(void *arg) @@ -730,10 +763,10 @@ static void atmel_complete_tx_dma(void *arg) if (chan) dmaengine_terminate_all(chan); - xmit->tail += sg_dma_len(&atmel_port->sg_tx); + xmit->tail += atmel_port->tx_len; xmit->tail &= UART_XMIT_SIZE - 1; - port->icount.tx += sg_dma_len(&atmel_port->sg_tx); + port->icount.tx += atmel_port->tx_len; spin_lock_irq(&atmel_port->lock_tx); async_tx_ack(atmel_port->desc_tx); @@ -781,7 +814,9 @@ static void atmel_tx_dma(struct uart_port *port) struct circ_buf *xmit = &port->state->xmit; struct dma_chan *chan = atmel_port->chan_tx; struct dma_async_tx_descriptor *desc; - struct scatterlist *sg = &atmel_port->sg_tx; + struct scatterlist sgl[2], *sg, *sg_tx = &atmel_port->sg_tx; + unsigned int tx_len, part1_len, part2_len, sg_len; + dma_addr_t phys_addr; /* Make sure we have an idle channel */ if (atmel_port->desc_tx != NULL) @@ -797,18 +832,46 @@ static void atmel_tx_dma(struct uart_port *port) * Take the port lock to get a * consistent xmit buffer state. */ - sg->offset = xmit->tail & (UART_XMIT_SIZE - 1); - sg_dma_address(sg) = (sg_dma_address(sg) & - ~(UART_XMIT_SIZE - 1)) - + sg->offset; - sg_dma_len(sg) = CIRC_CNT_TO_END(xmit->head, - xmit->tail, - UART_XMIT_SIZE); - BUG_ON(!sg_dma_len(sg)); + tx_len = CIRC_CNT_TO_END(xmit->head, + xmit->tail, + UART_XMIT_SIZE); + + if (atmel_port->fifo_size) { + /* multi data mode */ + part1_len = (tx_len & ~0x3); /* DWORD access */ + part2_len = (tx_len & 0x3); /* BYTE access */ + } else { + /* single data (legacy) mode */ + part1_len = 0; + part2_len = tx_len; /* BYTE access only */ + } + + sg_init_table(sgl, 2); + sg_len = 0; + phys_addr = sg_dma_address(sg_tx) + xmit->tail; + if (part1_len) { + sg = &sgl[sg_len++]; + sg_dma_address(sg) = phys_addr; + sg_dma_len(sg) = part1_len; + + phys_addr += part1_len; + } + + if (part2_len) { + sg = &sgl[sg_len++]; + sg_dma_address(sg) = phys_addr; + sg_dma_len(sg) = part2_len; + } + + /* + * save tx_len so atmel_complete_tx_dma() will increase + * xmit->tail correctly + */ + atmel_port->tx_len = tx_len; desc = dmaengine_prep_slave_sg(chan, - sg, - 1, + sgl, + sg_len, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT | DMA_CTRL_ACK); @@ -817,7 +880,7 @@ static void atmel_tx_dma(struct uart_port *port) return; } - dma_sync_sg_for_device(port->dev, sg, 1, DMA_TO_DEVICE); + dma_sync_sg_for_device(port->dev, sg_tx, 1, DMA_TO_DEVICE); atmel_port->desc_tx = desc; desc->callback = atmel_complete_tx_dma; @@ -877,7 +940,9 @@ static int atmel_prepare_tx_dma(struct uart_port *port) /* Configure the slave DMA */ memset(&config, 0, sizeof(config)); config.direction = DMA_MEM_TO_DEV; - config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + config.dst_addr_width = (atmel_port->fifo_size) ? + DMA_SLAVE_BUSWIDTH_4_BYTES : + DMA_SLAVE_BUSWIDTH_1_BYTE; config.dst_addr = port->mapbase + ATMEL_US_THR; config.dst_maxburst = 1; @@ -935,14 +1000,14 @@ static void atmel_rx_from_dma(struct uart_port *port) /* Reset the UART timeout early so that we don't miss one */ - UART_PUT_CR(port, ATMEL_US_STTTO); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); dmastat = dmaengine_tx_status(chan, atmel_port->cookie_rx, &state); /* Restart a new tasklet if DMA status is error */ if (dmastat == DMA_ERROR) { dev_dbg(port->dev, "Get residue error, restart tasklet\n"); - UART_PUT_IER(port, ATMEL_US_TIMEOUT); + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT); tasklet_schedule(&atmel_port->tasklet); return; } @@ -1008,7 +1073,7 @@ static void atmel_rx_from_dma(struct uart_port *port) tty_flip_buffer_push(tport); spin_lock(&port->lock); - UART_PUT_IER(port, ATMEL_US_TIMEOUT); + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT); } static int atmel_prepare_rx_dma(struct uart_port *port) @@ -1118,8 +1183,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending) * the moment. */ if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) { - UART_PUT_IDR(port, (ATMEL_US_ENDRX - | ATMEL_US_TIMEOUT)); + atmel_uart_writel(port, ATMEL_US_IDR, + (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)); tasklet_schedule(&atmel_port->tasklet); } @@ -1130,7 +1195,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending) if (atmel_use_dma_rx(port)) { if (pending & ATMEL_US_TIMEOUT) { - UART_PUT_IDR(port, ATMEL_US_TIMEOUT); + atmel_uart_writel(port, ATMEL_US_IDR, + ATMEL_US_TIMEOUT); tasklet_schedule(&atmel_port->tasklet); } } @@ -1143,8 +1209,8 @@ atmel_handle_receive(struct uart_port *port, unsigned int pending) * End of break detected. If it came along with a * character, atmel_rx_chars will handle it. */ - UART_PUT_CR(port, ATMEL_US_RSTSTA); - UART_PUT_IDR(port, ATMEL_US_RXBRK); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); + atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK); atmel_port->break_active = 0; } } @@ -1159,7 +1225,8 @@ atmel_handle_transmit(struct uart_port *port, unsigned int pending) if (pending & atmel_port->tx_done_mask) { /* Either PDC or interrupt transmission */ - UART_PUT_IDR(port, atmel_port->tx_done_mask); + atmel_uart_writel(port, ATMEL_US_IDR, + atmel_port->tx_done_mask); tasklet_schedule(&atmel_port->tasklet); } } @@ -1197,7 +1264,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) do { status = atmel_get_lines_status(port); - mask = UART_GET_IMR(port); + mask = atmel_uart_readl(port, ATMEL_US_IMR); pending = status & mask; if (!gpio_handled) { /* @@ -1223,7 +1290,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) if (atmel_port->suspended) { atmel_port->pending |= pending; atmel_port->pending_status = status; - UART_PUT_IDR(port, mask); + atmel_uart_writel(port, ATMEL_US_IDR, mask); pm_system_wakeup(); break; } @@ -1260,7 +1327,7 @@ static void atmel_tx_pdc(struct uart_port *port) int count; /* nothing left to transmit? */ - if (UART_GET_TCR(port)) + if (atmel_uart_readl(port, ATMEL_PDC_TCR)) return; xmit->tail += pdc->ofs; @@ -1272,7 +1339,7 @@ static void atmel_tx_pdc(struct uart_port *port) /* more to transmit - setup next transfer */ /* disable PDC transmit */ - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) { dma_sync_single_for_device(port->dev, @@ -1283,12 +1350,14 @@ static void atmel_tx_pdc(struct uart_port *port) count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); pdc->ofs = count; - UART_PUT_TPR(port, pdc->dma_addr + xmit->tail); - UART_PUT_TCR(port, count); + atmel_uart_writel(port, ATMEL_PDC_TPR, + pdc->dma_addr + xmit->tail); + atmel_uart_writel(port, ATMEL_PDC_TCR, count); /* re-enable PDC transmit */ - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); /* Enable interrupts */ - UART_PUT_IER(port, atmel_port->tx_done_mask); + atmel_uart_writel(port, ATMEL_US_IER, + atmel_port->tx_done_mask); } else { if ((port->rs485.flags & SER_RS485_ENABLED) && !(port->rs485.flags & SER_RS485_RX_DURING_TX)) { @@ -1414,10 +1483,10 @@ static void atmel_rx_from_pdc(struct uart_port *port) do { /* Reset the UART timeout early so that we don't miss one */ - UART_PUT_CR(port, ATMEL_US_STTTO); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); pdc = &atmel_port->pdc_rx[rx_idx]; - head = UART_GET_RPR(port) - pdc->dma_addr; + head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr; tail = pdc->ofs; /* If the PDC has switched buffers, RPR won't contain @@ -1460,8 +1529,8 @@ static void atmel_rx_from_pdc(struct uart_port *port) */ if (head >= pdc->dma_size) { pdc->ofs = 0; - UART_PUT_RNPR(port, pdc->dma_addr); - UART_PUT_RNCR(port, pdc->dma_size); + atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr); + atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size); rx_idx = !rx_idx; atmel_port->pdc_rx_idx = rx_idx; @@ -1476,7 +1545,8 @@ static void atmel_rx_from_pdc(struct uart_port *port) tty_flip_buffer_push(tport); spin_lock(&port->lock); - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); + atmel_uart_writel(port, ATMEL_US_IER, + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); } static int atmel_prepare_rx_pdc(struct uart_port *port) @@ -1509,11 +1579,12 @@ static int atmel_prepare_rx_pdc(struct uart_port *port) atmel_port->pdc_rx_idx = 0; - UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr); - UART_PUT_RCR(port, PDC_BUFFER_SIZE); + atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr); + atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE); - UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr); - UART_PUT_RNCR(port, PDC_BUFFER_SIZE); + atmel_uart_writel(port, ATMEL_PDC_RNPR, + atmel_port->pdc_rx[1].dma_addr); + atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE); return 0; } @@ -1667,7 +1738,7 @@ static void atmel_set_ops(struct uart_port *port) static void atmel_get_ip_name(struct uart_port *port) { struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); - int name = UART_GET_IP_NAME(port); + int name = atmel_uart_readl(port, ATMEL_US_NAME); u32 version; int usart, uart; /* usart and uart ascii */ @@ -1684,7 +1755,7 @@ static void atmel_get_ip_name(struct uart_port *port) atmel_port->is_usart = false; } else { /* fallback for older SoCs: use version field */ - version = UART_GET_IP_VERSION(port); + version = atmel_uart_readl(port, ATMEL_US_VERSION); switch (version) { case 0x302: case 0x10213: @@ -1756,7 +1827,7 @@ static int atmel_startup(struct uart_port *port) * request_irq() is called we could get stuck trying to * handle an unexpected interrupt */ - UART_PUT_IDR(port, -1); + atmel_uart_writel(port, ATMEL_US_IDR, -1); atmel_port->ms_irq_enabled = false; /* @@ -1797,6 +1868,32 @@ static int atmel_startup(struct uart_port *port) atmel_set_ops(port); } + /* + * Enable FIFO when available + */ + if (atmel_port->fifo_size) { + unsigned int txrdym = ATMEL_US_ONE_DATA; + unsigned int rxrdym = ATMEL_US_ONE_DATA; + unsigned int fmr; + + atmel_uart_writel(port, ATMEL_US_CR, + ATMEL_US_FIFOEN | + ATMEL_US_RXFCLR | + ATMEL_US_TXFLCLR); + + if (atmel_use_dma_tx(port)) + txrdym = ATMEL_US_FOUR_DATA; + + fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym); + if (atmel_port->rts_high && + atmel_port->rts_low) + fmr |= ATMEL_US_FRTSC | + ATMEL_US_RXFTHRES(atmel_port->rts_high) | + ATMEL_US_RXFTHRES2(atmel_port->rts_low); + + atmel_uart_writel(port, ATMEL_US_FMR, fmr); + } + /* Save current CSR for comparison in atmel_tasklet_func() */ atmel_port->irq_status_prev = atmel_get_lines_status(port); atmel_port->irq_status = atmel_port->irq_status_prev; @@ -1804,9 +1901,9 @@ static int atmel_startup(struct uart_port *port) /* * Finally, enable the serial port */ - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); /* enable xmit & rcvr */ - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); setup_timer(&atmel_port->uart_timer, atmel_uart_timer_callback, @@ -1819,13 +1916,14 @@ static int atmel_startup(struct uart_port *port) jiffies + uart_poll_timeout(port)); /* set USART timeout */ } else { - UART_PUT_RTOR(port, PDC_RX_TIMEOUT); - UART_PUT_CR(port, ATMEL_US_STTTO); + atmel_uart_writel(port, ATMEL_US_RTOR, PDC_RX_TIMEOUT); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); - UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); + atmel_uart_writel(port, ATMEL_US_IER, + ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); } /* enable PDC controller */ - UART_PUT_PTCR(port, ATMEL_PDC_RXTEN); + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); } else if (atmel_use_dma_rx(port)) { /* set UART timeout */ if (!atmel_port->is_usart) { @@ -1833,14 +1931,15 @@ static int atmel_startup(struct uart_port *port) jiffies + uart_poll_timeout(port)); /* set USART timeout */ } else { - UART_PUT_RTOR(port, PDC_RX_TIMEOUT); - UART_PUT_CR(port, ATMEL_US_STTTO); + atmel_uart_writel(port, ATMEL_US_RTOR, PDC_RX_TIMEOUT); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); - UART_PUT_IER(port, ATMEL_US_TIMEOUT); + atmel_uart_writel(port, ATMEL_US_IER, + ATMEL_US_TIMEOUT); } } else { /* enable receive only */ - UART_PUT_IER(port, ATMEL_US_RXRDY); + atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY); } return 0; @@ -1860,7 +1959,7 @@ static void atmel_flush_buffer(struct uart_port *port) struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); if (atmel_use_pdc_tx(port)) { - UART_PUT_TCR(port, 0); + atmel_uart_writel(port, ATMEL_PDC_TCR, 0); atmel_port->pdc_tx.ofs = 0; } } @@ -1892,8 +1991,8 @@ static void atmel_shutdown(struct uart_port *port) atmel_stop_rx(port); atmel_stop_tx(port); - UART_PUT_CR(port, ATMEL_US_RSTSTA); - UART_PUT_IDR(port, -1); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); + atmel_uart_writel(port, ATMEL_US_IDR, -1); /* @@ -1938,12 +2037,12 @@ static void atmel_serial_pm(struct uart_port *port, unsigned int state, clk_prepare_enable(atmel_port->clk); /* re-enable interrupts if we disabled some on suspend */ - UART_PUT_IER(port, atmel_port->backup_imr); + atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr); break; case 3: /* Back up the interrupt mask and disable all interrupts */ - atmel_port->backup_imr = UART_GET_IMR(port); - UART_PUT_IDR(port, -1); + atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR); + atmel_uart_writel(port, ATMEL_US_IDR, -1); /* * Disable the peripheral clock for this serial port. @@ -1966,7 +2065,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, unsigned int old_mode, mode, imr, quot, baud; /* save the current mode register */ - mode = old_mode = UART_GET_MR(port); + mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR); /* reset the mode, clock divisor, parity, stop bits and data size */ mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP | @@ -2025,7 +2124,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, if (atmel_use_pdc_rx(port)) /* need to enable error interrupts */ - UART_PUT_IER(port, port->read_status_mask); + atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask); /* * Characters to ignore @@ -2052,15 +2151,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, * transmitter is empty if requested by the caller, so there's * no need to wait for it here. */ - imr = UART_GET_IMR(port); - UART_PUT_IDR(port, -1); + imr = atmel_uart_readl(port, ATMEL_US_IMR); + atmel_uart_writel(port, ATMEL_US_IDR, -1); /* disable receiver and transmitter */ - UART_PUT_CR(port, ATMEL_US_TXDIS | ATMEL_US_RXDIS); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS); /* mode */ if (port->rs485.flags & SER_RS485_ENABLED) { - UART_PUT_TTGR(port, port->rs485.delay_rts_after_send); + atmel_uart_writel(port, ATMEL_US_TTGR, + port->rs485.delay_rts_after_send); mode |= ATMEL_US_USMODE_RS485; } else if (termios->c_cflag & CRTSCTS) { /* RS232 with hardware handshake (RTS/CTS) */ @@ -2071,7 +2171,7 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, } /* set the mode, clock divisor, parity, stop bits and data size */ - UART_PUT_MR(port, mode); + atmel_uart_writel(port, ATMEL_US_MR, mode); /* * when switching the mode, set the RTS line state according to the @@ -2088,16 +2188,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, rts_state = ATMEL_US_RTSEN; } - UART_PUT_CR(port, rts_state); + atmel_uart_writel(port, ATMEL_US_CR, rts_state); } /* set the baud rate */ - UART_PUT_BRGR(port, quot); - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); + atmel_uart_writel(port, ATMEL_US_BRGR, quot); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); /* restore interrupts */ - UART_PUT_IER(port, imr); + atmel_uart_writel(port, ATMEL_US_IER, imr); /* CTS flow-control and modem-status interrupts */ if (UART_ENABLE_MS(port, termios->c_cflag)) @@ -2208,18 +2308,18 @@ static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser) #ifdef CONFIG_CONSOLE_POLL static int atmel_poll_get_char(struct uart_port *port) { - while (!(UART_GET_CSR(port) & ATMEL_US_RXRDY)) + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY)) cpu_relax(); - return UART_GET_CHAR(port); + return atmel_uart_read_char(port); } static void atmel_poll_put_char(struct uart_port *port, unsigned char ch) { - while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY)) + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) cpu_relax(); - UART_PUT_CHAR(port, ch); + atmel_uart_write_char(port, ch); } #endif @@ -2324,9 +2424,9 @@ struct platform_device *atmel_default_console_device; /* the serial console devi #ifdef CONFIG_SERIAL_ATMEL_CONSOLE static void atmel_console_putchar(struct uart_port *port, int ch) { - while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY)) + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) cpu_relax(); - UART_PUT_CHAR(port, ch); + atmel_uart_write_char(port, ch); } /* @@ -2342,12 +2442,13 @@ static void atmel_console_write(struct console *co, const char *s, u_int count) /* * First, save IMR and then disable interrupts */ - imr = UART_GET_IMR(port); - UART_PUT_IDR(port, ATMEL_US_RXRDY | atmel_port->tx_done_mask); + imr = atmel_uart_readl(port, ATMEL_US_IMR); + atmel_uart_writel(port, ATMEL_US_IDR, + ATMEL_US_RXRDY | atmel_port->tx_done_mask); /* Store PDC transmit status and disable it */ - pdc_tx = UART_GET_PTSR(port) & ATMEL_PDC_TXTEN; - UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); + pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN; + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); uart_console_write(port, s, count, atmel_console_putchar); @@ -2356,15 +2457,15 @@ static void atmel_console_write(struct console *co, const char *s, u_int count) * and restore IMR */ do { - status = UART_GET_CSR(port); + status = atmel_uart_readl(port, ATMEL_US_CSR); } while (!(status & ATMEL_US_TXRDY)); /* Restore PDC transmit status */ if (pdc_tx) - UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); + atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); /* set interrupts back the way they were */ - UART_PUT_IER(port, imr); + atmel_uart_writel(port, ATMEL_US_IER, imr); } /* @@ -2380,17 +2481,17 @@ static void __init atmel_console_get_options(struct uart_port *port, int *baud, * If the baud rate generator isn't running, the port wasn't * initialized by the boot loader. */ - quot = UART_GET_BRGR(port) & ATMEL_US_CD; + quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD; if (!quot) return; - mr = UART_GET_MR(port) & ATMEL_US_CHRL; + mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL; if (mr == ATMEL_US_CHRL_8) *bits = 8; else *bits = 7; - mr = UART_GET_MR(port) & ATMEL_US_PAR; + mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR; if (mr == ATMEL_US_PAR_EVEN) *parity = 'e'; else if (mr == ATMEL_US_PAR_ODD) @@ -2423,9 +2524,9 @@ static int __init atmel_console_setup(struct console *co, char *options) if (ret) return ret; - UART_PUT_IDR(port, -1); - UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); - UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); + atmel_uart_writel(port, ATMEL_US_IDR, -1); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); + atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); if (options) uart_parse_options(options, &baud, &parity, &bits, &flow); @@ -2532,7 +2633,8 @@ static int atmel_serial_suspend(struct platform_device *pdev, if (atmel_is_console_port(port) && console_suspend_enabled) { /* Drain the TX shifter */ - while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY)) + while (!(atmel_uart_readl(port, ATMEL_US_CSR) & + ATMEL_US_TXEMPTY)) cpu_relax(); } @@ -2599,6 +2701,48 @@ static int atmel_init_gpios(struct atmel_uart_port *p, struct device *dev) return 0; } +static void atmel_serial_probe_fifos(struct atmel_uart_port *port, + struct platform_device *pdev) +{ + port->fifo_size = 0; + port->rts_low = 0; + port->rts_high = 0; + + if (of_property_read_u32(pdev->dev.of_node, + "atmel,fifo-size", + &port->fifo_size)) + return; + + if (!port->fifo_size) + return; + + if (port->fifo_size < ATMEL_MIN_FIFO_SIZE) { + port->fifo_size = 0; + dev_err(&pdev->dev, "Invalid FIFO size\n"); + return; + } + + /* + * 0 <= rts_low <= rts_high <= fifo_size + * Once their CTS line asserted by the remote peer, some x86 UARTs tend + * to flush their internal TX FIFO, commonly up to 16 data, before + * actually stopping to send new data. So we try to set the RTS High + * Threshold to a reasonably high value respecting this 16 data + * empirical rule when possible. + */ + port->rts_high = max_t(int, port->fifo_size >> 1, + port->fifo_size - ATMEL_RTS_HIGH_OFFSET); + port->rts_low = max_t(int, port->fifo_size >> 2, + port->fifo_size - ATMEL_RTS_LOW_OFFSET); + + dev_info(&pdev->dev, "Using FIFO (%u data)\n", + port->fifo_size); + dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n", + port->rts_high); + dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n", + port->rts_low); +} + static int atmel_serial_probe(struct platform_device *pdev) { struct atmel_uart_port *port; @@ -2635,6 +2779,7 @@ static int atmel_serial_probe(struct platform_device *pdev) port = &atmel_ports[ret]; port->backup_imr = 0; port->uart.line = ret; + atmel_serial_probe_fifos(port, pdev); spin_lock_init(&port->lock_suspended); @@ -2684,8 +2829,9 @@ static int atmel_serial_probe(struct platform_device *pdev) clk_prepare_enable(port->clk); if (rs485_enabled) { - UART_PUT_MR(&port->uart, ATMEL_US_USMODE_NORMAL); - UART_PUT_CR(&port->uart, ATMEL_US_RTSEN); + atmel_uart_writel(&port->uart, ATMEL_US_MR, + ATMEL_US_USMODE_NORMAL); + atmel_uart_writel(&port->uart, ATMEL_US_CR, ATMEL_US_RTSEN); } /* diff --git a/drivers/tty/serial/etraxfs-uart.c b/drivers/tty/serial/etraxfs-uart.c index 679709f51..6813e316e 100644 --- a/drivers/tty/serial/etraxfs-uart.c +++ b/drivers/tty/serial/etraxfs-uart.c @@ -10,6 +10,8 @@ #include #include +#include "serial_mctrl_gpio.h" + #define DRV_NAME "etraxfs-uart" #define UART_NR CONFIG_ETRAX_SERIAL_PORTS @@ -28,10 +30,7 @@ struct uart_cris_port { void __iomem *regi_ser; - struct gpio_desc *dtr_pin; - struct gpio_desc *dsr_pin; - struct gpio_desc *ri_pin; - struct gpio_desc *cd_pin; + struct mctrl_gpios *gpios; int write_ongoing; }; @@ -112,17 +111,10 @@ cris_console_setup(struct console *co, char *options) return 0; } -static struct tty_driver *cris_console_device(struct console *co, int *index) -{ - struct uart_driver *p = co->data; - *index = co->index; - return p->tty_driver; -} - static struct console cris_console = { .name = "ttyS", .write = cris_console_write, - .device = cris_console_device, + .device = uart_console_device, .setup = cris_console_setup, .flags = CON_PRINTBUFFER, .index = -1, @@ -373,14 +365,6 @@ static void etraxfs_uart_stop_rx(struct uart_port *port) REG_WR(ser, regi_ser, rw_rec_ctrl, rec_ctrl); } -static void etraxfs_uart_enable_ms(struct uart_port *port) -{ -} - -static void check_modem_status(struct uart_cris_port *up) -{ -} - static unsigned int etraxfs_uart_tx_empty(struct uart_port *port) { struct uart_cris_port *up = (struct uart_cris_port *)port; @@ -404,21 +388,9 @@ static unsigned int etraxfs_uart_get_mctrl(struct uart_port *port) ret = 0; if (crisv32_serial_get_rts(up)) ret |= TIOCM_RTS; - /* DTR is active low */ - if (up->dtr_pin && !gpiod_get_raw_value(up->dtr_pin)) - ret |= TIOCM_DTR; - /* CD is active low */ - if (up->cd_pin && !gpiod_get_raw_value(up->cd_pin)) - ret |= TIOCM_CD; - /* RI is active low */ - if (up->ri_pin && !gpiod_get_raw_value(up->ri_pin)) - ret |= TIOCM_RI; - /* DSR is active low */ - if (up->dsr_pin && !gpiod_get_raw_value(up->dsr_pin)) - ret |= TIOCM_DSR; if (crisv32_serial_get_cts(up)) ret |= TIOCM_CTS; - return ret; + return mctrl_gpio_get(up->gpios, &ret); } static void etraxfs_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) @@ -426,15 +398,7 @@ static void etraxfs_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) struct uart_cris_port *up = (struct uart_cris_port *)port; crisv32_serial_set_rts(up, mctrl & TIOCM_RTS ? 1 : 0, 0); - /* DTR is active low */ - if (up->dtr_pin) - gpiod_set_raw_value(up->dtr_pin, mctrl & TIOCM_DTR ? 0 : 1); - /* RI is active low */ - if (up->ri_pin) - gpiod_set_raw_value(up->ri_pin, mctrl & TIOCM_RNG ? 0 : 1); - /* CD is active low */ - if (up->cd_pin) - gpiod_set_raw_value(up->cd_pin, mctrl & TIOCM_CD ? 0 : 1); + mctrl_gpio_set(up->gpios, mctrl); } static void etraxfs_uart_break_ctl(struct uart_port *port, int break_state) @@ -598,7 +562,6 @@ ser_interrupt(int irq, void *dev_id) receive_chars_no_dma(up); handled = 1; } - check_modem_status(up); if (masked_intr.tr_rdy) { transmit_chars_no_dma(up); @@ -862,7 +825,6 @@ static const struct uart_ops etraxfs_uart_pops = { .start_tx = etraxfs_uart_start_tx, .send_xchar = etraxfs_uart_send_xchar, .stop_rx = etraxfs_uart_stop_rx, - .enable_ms = etraxfs_uart_enable_ms, .break_ctl = etraxfs_uart_break_ctl, .startup = etraxfs_uart_startup, .shutdown = etraxfs_uart_shutdown, @@ -930,11 +892,12 @@ static int etraxfs_uart_probe(struct platform_device *pdev) up->irq = irq_of_parse_and_map(np, 0); up->regi_ser = of_iomap(np, 0); - up->dtr_pin = devm_gpiod_get_optional(&pdev->dev, "dtr"); - up->dsr_pin = devm_gpiod_get_optional(&pdev->dev, "dsr"); - up->ri_pin = devm_gpiod_get_optional(&pdev->dev, "ri"); - up->cd_pin = devm_gpiod_get_optional(&pdev->dev, "cd"); up->port.dev = &pdev->dev; + + up->gpios = mctrl_gpio_init(&pdev->dev, 0); + if (IS_ERR(up->gpios)) + return PTR_ERR(up->gpios); + cris_serial_port_init(&up->port, dev_id); etraxfs_uart_ports[dev_id] = up; diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index 54fdc7866..d0388a071 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -216,6 +216,8 @@ struct imx_port { unsigned int tx_bytes; unsigned int dma_tx_nents; wait_queue_head_t dma_wait; + unsigned int saved_reg[10]; + bool context_saved; }; struct imx_port_ucrs { @@ -700,7 +702,8 @@ static irqreturn_t imx_rxint(int irq, void *dev_id) if (sport->port.ignore_status_mask & URXD_DUMMY_READ) goto out; - tty_insert_flip_char(port, rx, flg); + if (tty_insert_flip_char(port, rx, flg) == 0) + sport->port.icount.buf_overrun++; } out: @@ -766,7 +769,6 @@ static irqreturn_t imx_int(int irq, void *dev_id) writel(USR1_AWAKE, sport->port.membase + USR1); if (sts2 & USR2_ORE) { - dev_err(sport->port.dev, "Rx FIFO overrun\n"); sport->port.icount.overrun++; writel(USR2_ORE, sport->port.membase + USR2); } @@ -921,8 +923,13 @@ static void dma_rx_callback(void *data) dev_dbg(sport->port.dev, "We get %d bytes.\n", count); if (count) { - if (!(sport->port.ignore_status_mask & URXD_DUMMY_READ)) - tty_insert_flip_string(port, sport->rx_buf, count); + if (!(sport->port.ignore_status_mask & URXD_DUMMY_READ)) { + int bytes = tty_insert_flip_string(port, sport->rx_buf, + count); + + if (bytes != count) + sport->port.icount.buf_overrun++; + } tty_flip_buffer_push(port); start_rx_dma(sport); @@ -1810,36 +1817,6 @@ static struct uart_driver imx_reg = { .cons = IMX_CONSOLE, }; -static int serial_imx_suspend(struct platform_device *dev, pm_message_t state) -{ - struct imx_port *sport = platform_get_drvdata(dev); - unsigned int val; - - /* enable wakeup from i.MX UART */ - val = readl(sport->port.membase + UCR3); - val |= UCR3_AWAKEN; - writel(val, sport->port.membase + UCR3); - - uart_suspend_port(&imx_reg, &sport->port); - - return 0; -} - -static int serial_imx_resume(struct platform_device *dev) -{ - struct imx_port *sport = platform_get_drvdata(dev); - unsigned int val; - - /* disable wakeup from i.MX UART */ - val = readl(sport->port.membase + UCR3); - val &= ~UCR3_AWAKEN; - writel(val, sport->port.membase + UCR3); - - uart_resume_port(&imx_reg, &sport->port); - - return 0; -} - #ifdef CONFIG_OF /* * This function returns 1 iff pdev isn't a device instatiated by dt, 0 iff it @@ -1901,7 +1878,7 @@ static int serial_imx_probe(struct platform_device *pdev) { struct imx_port *sport; void __iomem *base; - int ret = 0; + int ret = 0, reg; struct resource *res; int txirq, rxirq, rtsirq; @@ -1956,6 +1933,19 @@ static int serial_imx_probe(struct platform_device *pdev) sport->port.uartclk = clk_get_rate(sport->clk_per); + /* For register access, we only need to enable the ipg clock. */ + ret = clk_prepare_enable(sport->clk_ipg); + if (ret) + return ret; + + /* Disable interrupts before requesting them */ + reg = readl_relaxed(sport->port.membase + UCR1); + reg &= ~(UCR1_ADEN | UCR1_TRDYEN | UCR1_IDEN | UCR1_RRDYEN | + UCR1_TXMPTYEN | UCR1_RTSDEN); + writel_relaxed(reg, sport->port.membase + UCR1); + + clk_disable_unprepare(sport->clk_ipg); + /* * Allocate the IRQ(s) i.MX1 has three interrupts whereas later * chips only have one interrupt. @@ -1991,16 +1981,135 @@ static int serial_imx_remove(struct platform_device *pdev) return uart_remove_one_port(&imx_reg, &sport->port); } +static void serial_imx_restore_context(struct imx_port *sport) +{ + if (!sport->context_saved) + return; + + writel(sport->saved_reg[4], sport->port.membase + UFCR); + writel(sport->saved_reg[5], sport->port.membase + UESC); + writel(sport->saved_reg[6], sport->port.membase + UTIM); + writel(sport->saved_reg[7], sport->port.membase + UBIR); + writel(sport->saved_reg[8], sport->port.membase + UBMR); + writel(sport->saved_reg[9], sport->port.membase + IMX21_UTS); + writel(sport->saved_reg[0], sport->port.membase + UCR1); + writel(sport->saved_reg[1] | UCR2_SRST, sport->port.membase + UCR2); + writel(sport->saved_reg[2], sport->port.membase + UCR3); + writel(sport->saved_reg[3], sport->port.membase + UCR4); + sport->context_saved = false; +} + +static void serial_imx_save_context(struct imx_port *sport) +{ + /* Save necessary regs */ + sport->saved_reg[0] = readl(sport->port.membase + UCR1); + sport->saved_reg[1] = readl(sport->port.membase + UCR2); + sport->saved_reg[2] = readl(sport->port.membase + UCR3); + sport->saved_reg[3] = readl(sport->port.membase + UCR4); + sport->saved_reg[4] = readl(sport->port.membase + UFCR); + sport->saved_reg[5] = readl(sport->port.membase + UESC); + sport->saved_reg[6] = readl(sport->port.membase + UTIM); + sport->saved_reg[7] = readl(sport->port.membase + UBIR); + sport->saved_reg[8] = readl(sport->port.membase + UBMR); + sport->saved_reg[9] = readl(sport->port.membase + IMX21_UTS); + sport->context_saved = true; +} + +static void serial_imx_enable_wakeup(struct imx_port *sport, bool on) +{ + unsigned int val; + + val = readl(sport->port.membase + UCR3); + if (on) + val |= UCR3_AWAKEN; + else + val &= ~UCR3_AWAKEN; + writel(val, sport->port.membase + UCR3); + + val = readl(sport->port.membase + UCR1); + if (on) + val |= UCR1_RTSDEN; + else + val &= ~UCR1_RTSDEN; + writel(val, sport->port.membase + UCR1); +} + +static int imx_serial_port_suspend_noirq(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct imx_port *sport = platform_get_drvdata(pdev); + int ret; + + ret = clk_enable(sport->clk_ipg); + if (ret) + return ret; + + serial_imx_save_context(sport); + + clk_disable(sport->clk_ipg); + + return 0; +} + +static int imx_serial_port_resume_noirq(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct imx_port *sport = platform_get_drvdata(pdev); + int ret; + + ret = clk_enable(sport->clk_ipg); + if (ret) + return ret; + + serial_imx_restore_context(sport); + + clk_disable(sport->clk_ipg); + + return 0; +} + +static int imx_serial_port_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct imx_port *sport = platform_get_drvdata(pdev); + + /* enable wakeup from i.MX UART */ + serial_imx_enable_wakeup(sport, true); + + uart_suspend_port(&imx_reg, &sport->port); + + return 0; +} + +static int imx_serial_port_resume(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct imx_port *sport = platform_get_drvdata(pdev); + + /* disable wakeup from i.MX UART */ + serial_imx_enable_wakeup(sport, false); + + uart_resume_port(&imx_reg, &sport->port); + + return 0; +} + +static const struct dev_pm_ops imx_serial_port_pm_ops = { + .suspend_noirq = imx_serial_port_suspend_noirq, + .resume_noirq = imx_serial_port_resume_noirq, + .suspend = imx_serial_port_suspend, + .resume = imx_serial_port_resume, +}; + static struct platform_driver serial_imx_driver = { .probe = serial_imx_probe, .remove = serial_imx_remove, - .suspend = serial_imx_suspend, - .resume = serial_imx_resume, .id_table = imx_uart_devtype, .driver = { .name = "imx-uart", .of_match_table = imx_uart_dt_ids, + .pm = &imx_serial_port_pm_ops, }, }; diff --git a/drivers/tty/serial/lantiq.c b/drivers/tty/serial/lantiq.c index 4ccc03976..b88832e8e 100644 --- a/drivers/tty/serial/lantiq.c +++ b/drivers/tty/serial/lantiq.c @@ -21,7 +21,6 @@ */ #include -#include #include #include #include @@ -740,7 +739,6 @@ static const struct of_device_id ltq_asc_match[] = { { .compatible = DRVNAME }, {}, }; -MODULE_DEVICE_TABLE(of, ltq_asc_match); static struct platform_driver lqasc_driver = { .driver = { @@ -764,8 +762,4 @@ init_lqasc(void) return ret; } - -module_init(init_lqasc); - -MODULE_DESCRIPTION("Lantiq serial port driver"); -MODULE_LICENSE("GPL"); +device_initcall(init_lqasc); diff --git a/drivers/tty/serial/men_z135_uart.c b/drivers/tty/serial/men_z135_uart.c index 5a41b8fbb..b90e7b304 100644 --- a/drivers/tty/serial/men_z135_uart.c +++ b/drivers/tty/serial/men_z135_uart.c @@ -839,7 +839,6 @@ static int men_z135_probe(struct mcb_device *mdev, uart->port.membase = NULL; uart->mdev = mdev; - spin_lock_init(&uart->port.lock); spin_lock_init(&uart->lock); err = uart_add_one_port(&men_z135_driver, &uart->port); diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c index 6fc07eb9d..41de374d9 100644 --- a/drivers/tty/serial/mpc52xx_uart.c +++ b/drivers/tty/serial/mpc52xx_uart.c @@ -239,8 +239,9 @@ static int mpc52xx_psc_tx_rdy(struct uart_port *port) static int mpc52xx_psc_tx_empty(struct uart_port *port) { - return in_be16(&PSC(port)->mpc52xx_psc_status) - & MPC52xx_PSC_SR_TXEMP; + u16 sts = in_be16(&PSC(port)->mpc52xx_psc_status); + + return (sts & MPC52xx_PSC_SR_TXEMP) ? TIOCSER_TEMT : 0; } static void mpc52xx_psc_start_tx(struct uart_port *port) diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c index 13cf7738f..7c7f30809 100644 --- a/drivers/tty/serial/mxs-auart.c +++ b/drivers/tty/serial/mxs-auart.c @@ -100,6 +100,8 @@ #define AUART_CTRL2_TXE (1 << 8) #define AUART_CTRL2_UARTEN (1 << 0) +#define AUART_LINECTRL_BAUD_DIV_MAX 0x003fffc0 +#define AUART_LINECTRL_BAUD_DIV_MIN 0x000000ec #define AUART_LINECTRL_BAUD_DIVINT_SHIFT 16 #define AUART_LINECTRL_BAUD_DIVINT_MASK 0xffff0000 #define AUART_LINECTRL_BAUD_DIVINT(v) (((v) & 0xffff) << 16) @@ -659,7 +661,7 @@ static void mxs_auart_settermios(struct uart_port *u, { struct mxs_auart_port *s = to_auart_port(u); u32 bm, ctrl, ctrl2, div; - unsigned int cflag, baud; + unsigned int cflag, baud, baud_min, baud_max; cflag = termios->c_cflag; @@ -752,7 +754,9 @@ static void mxs_auart_settermios(struct uart_port *u, } /* set baud rate */ - baud = uart_get_baud_rate(u, termios, old, 0, u->uartclk); + baud_min = DIV_ROUND_UP(u->uartclk * 32, AUART_LINECTRL_BAUD_DIV_MAX); + baud_max = u->uartclk * 32 / AUART_LINECTRL_BAUD_DIV_MIN; + baud = uart_get_baud_rate(u, termios, old, baud_min, baud_max); div = u->uartclk * 32 / baud; ctrl |= AUART_LINECTRL_BAUD_DIVFRAC(div & 0x3F); ctrl |= AUART_LINECTRL_BAUD_DIVINT(div >> 6); @@ -842,7 +846,7 @@ static irqreturn_t mxs_auart_irq_handle(int irq, void *context) return IRQ_HANDLED; } -static void mxs_auart_reset(struct uart_port *u) +static void mxs_auart_reset_deassert(struct uart_port *u) { int i; unsigned int reg; @@ -858,6 +862,30 @@ static void mxs_auart_reset(struct uart_port *u) writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR); } +static void mxs_auart_reset_assert(struct uart_port *u) +{ + int i; + u32 reg; + + reg = readl(u->membase + AUART_CTRL0); + /* if already in reset state, keep it untouched */ + if (reg & AUART_CTRL0_SFTRST) + return; + + writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR); + writel(AUART_CTRL0_SFTRST, u->membase + AUART_CTRL0_SET); + + for (i = 0; i < 1000; i++) { + reg = readl(u->membase + AUART_CTRL0); + /* reset is finished when the clock is gated */ + if (reg & AUART_CTRL0_CLKGATE) + return; + udelay(10); + } + + dev_err(u->dev, "Failed to reset the unit."); +} + static int mxs_auart_startup(struct uart_port *u) { int ret; @@ -867,7 +895,13 @@ static int mxs_auart_startup(struct uart_port *u) if (ret) return ret; - writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR); + if (uart_console(u)) { + writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR); + } else { + /* reset the unit to a well known state */ + mxs_auart_reset_assert(u); + mxs_auart_reset_deassert(u); + } writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_SET); @@ -899,12 +933,14 @@ static void mxs_auart_shutdown(struct uart_port *u) if (auart_dma_enabled(s)) mxs_auart_dma_exit(s); - writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_CLR); - - writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN, - u->membase + AUART_INTR_CLR); - - writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_SET); + if (uart_console(u)) { + writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_CLR); + writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN, + u->membase + AUART_INTR_CLR); + writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_SET); + } else { + mxs_auart_reset_assert(u); + } clk_disable_unprepare(s->clk); } @@ -1291,7 +1327,7 @@ static int mxs_auart_probe(struct platform_device *pdev) auart_port[s->port.line] = s; - mxs_auart_reset(&s->port); + mxs_auart_reset_deassert(&s->port); ret = uart_add_one_port(&auart_driver, &s->port); if (ret) diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c index 5916311ee..856686d6d 100644 --- a/drivers/tty/serial/samsung.c +++ b/drivers/tty/serial/samsung.c @@ -53,7 +53,6 @@ #include "samsung.h" #if defined(CONFIG_SERIAL_SAMSUNG_DEBUG) && \ - defined(CONFIG_DEBUG_LL) && \ !defined(MODULE) extern void printascii(const char *); diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c index 5ccc698cb..72ffd0dca 100644 --- a/drivers/tty/serial/sc16is7xx.c +++ b/drivers/tty/serial/sc16is7xx.c @@ -11,6 +11,8 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -29,6 +31,7 @@ #include #define SC16IS7XX_NAME "sc16is7xx" +#define SC16IS7XX_MAX_DEVS 8 /* SC16IS7XX register definitions */ #define SC16IS7XX_RHR_REG (0x00) /* RX FIFO */ @@ -312,14 +315,14 @@ struct sc16is7xx_one_config { struct sc16is7xx_one { struct uart_port port; + u8 line; struct kthread_work tx_work; struct kthread_work reg_work; struct sc16is7xx_one_config config; }; struct sc16is7xx_port { - struct uart_driver uart; - struct sc16is7xx_devtype *devtype; + const struct sc16is7xx_devtype *devtype; struct regmap *regmap; struct clk *clk; #ifdef CONFIG_GPIOLIB @@ -332,16 +335,31 @@ struct sc16is7xx_port { struct sc16is7xx_one p[0]; }; +static unsigned long sc16is7xx_lines; + +static struct uart_driver sc16is7xx_uart = { + .owner = THIS_MODULE, + .dev_name = "ttySC", + .nr = SC16IS7XX_MAX_DEVS, +}; + #define to_sc16is7xx_port(p,e) ((container_of((p), struct sc16is7xx_port, e))) #define to_sc16is7xx_one(p,e) ((container_of((p), struct sc16is7xx_one, e))) +static int sc16is7xx_line(struct uart_port *port) +{ + struct sc16is7xx_one *one = to_sc16is7xx_one(port, port); + + return one->line; +} + static u8 sc16is7xx_port_read(struct uart_port *port, u8 reg) { struct sc16is7xx_port *s = dev_get_drvdata(port->dev); unsigned int val = 0; + const u8 line = sc16is7xx_line(port); - regmap_read(s->regmap, - (reg << SC16IS7XX_REG_SHIFT) | port->line, &val); + regmap_read(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, &val); return val; } @@ -349,15 +367,16 @@ static u8 sc16is7xx_port_read(struct uart_port *port, u8 reg) static void sc16is7xx_port_write(struct uart_port *port, u8 reg, u8 val) { struct sc16is7xx_port *s = dev_get_drvdata(port->dev); + const u8 line = sc16is7xx_line(port); - regmap_write(s->regmap, - (reg << SC16IS7XX_REG_SHIFT) | port->line, val); + regmap_write(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, val); } static void sc16is7xx_fifo_read(struct uart_port *port, unsigned int rxlen) { struct sc16is7xx_port *s = dev_get_drvdata(port->dev); - u8 addr = (SC16IS7XX_RHR_REG << SC16IS7XX_REG_SHIFT) | port->line; + const u8 line = sc16is7xx_line(port); + u8 addr = (SC16IS7XX_RHR_REG << SC16IS7XX_REG_SHIFT) | line; regcache_cache_bypass(s->regmap, true); regmap_raw_read(s->regmap, addr, s->buf, rxlen); @@ -367,7 +386,8 @@ static void sc16is7xx_fifo_read(struct uart_port *port, unsigned int rxlen) static void sc16is7xx_fifo_write(struct uart_port *port, u8 to_send) { struct sc16is7xx_port *s = dev_get_drvdata(port->dev); - u8 addr = (SC16IS7XX_THR_REG << SC16IS7XX_REG_SHIFT) | port->line; + const u8 line = sc16is7xx_line(port); + u8 addr = (SC16IS7XX_THR_REG << SC16IS7XX_REG_SHIFT) | line; regcache_cache_bypass(s->regmap, true); regmap_raw_write(s->regmap, addr, s->buf, to_send); @@ -378,12 +398,24 @@ static void sc16is7xx_port_update(struct uart_port *port, u8 reg, u8 mask, u8 val) { struct sc16is7xx_port *s = dev_get_drvdata(port->dev); + const u8 line = sc16is7xx_line(port); - regmap_update_bits(s->regmap, - (reg << SC16IS7XX_REG_SHIFT) | port->line, + regmap_update_bits(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, mask, val); } +static int sc16is7xx_alloc_line(void) +{ + int i; + + BUILD_BUG_ON(SC16IS7XX_MAX_DEVS > BITS_PER_LONG); + + for (i = 0; i < SC16IS7XX_MAX_DEVS; i++) + if (!test_and_set_bit(i, &sc16is7xx_lines)) + break; + + return i; +} static void sc16is7xx_power(struct uart_port *port, int on) { @@ -508,7 +540,7 @@ static void sc16is7xx_handle_rx(struct uart_port *port, unsigned int rxlen, if (unlikely(rxlen >= sizeof(s->buf))) { dev_warn_ratelimited(port->dev, - "Port %i: Possible RX FIFO overrun: %d\n", + "ttySC%i: Possible RX FIFO overrun: %d\n", port->line, rxlen); port->icount.buf_overrun++; /* Ensure sanity of RX level */ @@ -649,7 +681,7 @@ static void sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno) break; default: dev_err_ratelimited(port->dev, - "Port %i: Unexpected interrupt: %x", + "ttySC%i: Unexpected interrupt: %x", port->line, iir); break; } @@ -661,7 +693,7 @@ static void sc16is7xx_ist(struct kthread_work *ws) struct sc16is7xx_port *s = to_sc16is7xx_port(ws, irq_work); int i; - for (i = 0; i < s->uart.nr; ++i) + for (i = 0; i < s->devtype->nr_uart; ++i) sc16is7xx_port_irq(s, i); } @@ -1099,7 +1131,7 @@ static int sc16is7xx_gpio_direction_output(struct gpio_chip *chip, #endif static int sc16is7xx_probe(struct device *dev, - struct sc16is7xx_devtype *devtype, + const struct sc16is7xx_devtype *devtype, struct regmap *regmap, int irq, unsigned long flags) { struct sched_param sched_param = { .sched_priority = MAX_RT_PRIO / 2 }; @@ -1134,23 +1166,13 @@ static int sc16is7xx_probe(struct device *dev, s->devtype = devtype; dev_set_drvdata(dev, s); - /* Register UART driver */ - s->uart.owner = THIS_MODULE; - s->uart.dev_name = "ttySC"; - s->uart.nr = devtype->nr_uart; - ret = uart_register_driver(&s->uart); - if (ret) { - dev_err(dev, "Registering UART driver failed\n"); - goto out_clk; - } - init_kthread_worker(&s->kworker); init_kthread_work(&s->irq_work, sc16is7xx_ist); s->kworker_task = kthread_run(kthread_worker_fn, &s->kworker, "sc16is7xx"); if (IS_ERR(s->kworker_task)) { ret = PTR_ERR(s->kworker_task); - goto out_uart; + goto out_clk; } sched_setscheduler(s->kworker_task, SCHED_FIFO, &sched_param); @@ -1174,8 +1196,8 @@ static int sc16is7xx_probe(struct device *dev, #endif for (i = 0; i < devtype->nr_uart; ++i) { + s->p[i].line = i; /* Initialize port data */ - s->p[i].port.line = i; s->p[i].port.dev = dev; s->p[i].port.irq = irq; s->p[i].port.type = PORT_SC16IS7XX; @@ -1185,6 +1207,12 @@ static int sc16is7xx_probe(struct device *dev, s->p[i].port.uartclk = freq; s->p[i].port.rs485_config = sc16is7xx_config_rs485; s->p[i].port.ops = &sc16is7xx_ops; + s->p[i].port.line = sc16is7xx_alloc_line(); + if (s->p[i].port.line >= SC16IS7XX_MAX_DEVS) { + ret = -ENOMEM; + goto out_ports; + } + /* Disable all interrupts */ sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_IER_REG, 0); /* Disable TX/RX */ @@ -1195,7 +1223,7 @@ static int sc16is7xx_probe(struct device *dev, init_kthread_work(&s->p[i].tx_work, sc16is7xx_tx_proc); init_kthread_work(&s->p[i].reg_work, sc16is7xx_reg_proc); /* Register port */ - uart_add_one_port(&s->uart, &s->p[i].port); + uart_add_one_port(&sc16is7xx_uart, &s->p[i].port); /* Go to suspend mode */ sc16is7xx_power(&s->p[i].port, 0); } @@ -1206,8 +1234,11 @@ static int sc16is7xx_probe(struct device *dev, if (!ret) return 0; - for (i = 0; i < s->uart.nr; i++) - uart_remove_one_port(&s->uart, &s->p[i].port); +out_ports: + for (i--; i >= 0; i--) { + uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); + clear_bit(s->p[i].port.line, &sc16is7xx_lines); + } #ifdef CONFIG_GPIOLIB if (devtype->nr_gpio) @@ -1217,9 +1248,6 @@ out_thread: #endif kthread_stop(s->kworker_task); -out_uart: - uart_unregister_driver(&s->uart); - out_clk: if (!IS_ERR(s->clk)) clk_disable_unprepare(s->clk); @@ -1237,15 +1265,15 @@ static int sc16is7xx_remove(struct device *dev) gpiochip_remove(&s->gpio); #endif - for (i = 0; i < s->uart.nr; i++) { - uart_remove_one_port(&s->uart, &s->p[i].port); + for (i = 0; i < s->devtype->nr_uart; i++) { + uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port); + clear_bit(s->p[i].port.line, &sc16is7xx_lines); sc16is7xx_power(&s->p[i].port, 0); } flush_kthread_worker(&s->kworker); kthread_stop(s->kworker_task); - uart_unregister_driver(&s->uart); if (!IS_ERR(s->clk)) clk_disable_unprepare(s->clk); @@ -1275,7 +1303,7 @@ static struct regmap_config regcfg = { #ifdef CONFIG_SERIAL_SC16IS7XX_SPI static int sc16is7xx_spi_probe(struct spi_device *spi) { - struct sc16is7xx_devtype *devtype; + const struct sc16is7xx_devtype *devtype; unsigned long flags = 0; struct regmap *regmap; int ret; @@ -1344,7 +1372,7 @@ MODULE_ALIAS("spi:sc16is7xx"); static int sc16is7xx_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { - struct sc16is7xx_devtype *devtype; + const struct sc16is7xx_devtype *devtype; unsigned long flags = 0; struct regmap *regmap; @@ -1385,7 +1413,6 @@ MODULE_DEVICE_TABLE(i2c, sc16is7xx_i2c_id_table); static struct i2c_driver sc16is7xx_i2c_uart_driver = { .driver = { .name = SC16IS7XX_NAME, - .owner = THIS_MODULE, .of_match_table = of_match_ptr(sc16is7xx_dt_ids), }, .probe = sc16is7xx_i2c_probe, @@ -1398,7 +1425,14 @@ MODULE_ALIAS("i2c:sc16is7xx"); static int __init sc16is7xx_init(void) { - int ret = 0; + int ret; + + ret = uart_register_driver(&sc16is7xx_uart); + if (ret) { + pr_err("Registering UART driver failed\n"); + return ret; + } + #ifdef CONFIG_SERIAL_SC16IS7XX_I2C ret = i2c_add_driver(&sc16is7xx_i2c_uart_driver); if (ret < 0) { @@ -1427,6 +1461,7 @@ static void __exit sc16is7xx_exit(void) #ifdef CONFIG_SERIAL_SC16IS7XX_SPI spi_unregister_driver(&sc16is7xx_spi_uart_driver); #endif + uart_unregister_driver(&sc16is7xx_uart); } module_exit(sc16is7xx_exit); diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index f36852067..603d2cc3f 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -1377,7 +1377,6 @@ static void uart_close(struct tty_struct *tty, struct file *filp) struct uart_state *state = tty->driver_data; struct tty_port *port; struct uart_port *uport; - unsigned long flags; if (!state) { struct uart_driver *drv = tty->driver->driver_state; @@ -1403,10 +1402,9 @@ static void uart_close(struct tty_struct *tty, struct file *filp) * disable the receive line status interrupts. */ if (port->flags & ASYNC_INITIALIZED) { - unsigned long flags; - spin_lock_irqsave(&uport->lock, flags); + spin_lock_irq(&uport->lock); uport->ops->stop_rx(uport); - spin_unlock_irqrestore(&uport->lock, flags); + spin_unlock_irq(&uport->lock); /* * Before we drop DTR, make sure the UART transmitter * has completely drained; this is especially @@ -1419,17 +1417,17 @@ static void uart_close(struct tty_struct *tty, struct file *filp) uart_shutdown(tty, state); tty_port_tty_set(port, NULL); - spin_lock_irqsave(&port->lock, flags); + spin_lock_irq(&port->lock); if (port->blocked_open) { - spin_unlock_irqrestore(&port->lock, flags); + spin_unlock_irq(&port->lock); if (port->close_delay) msleep_interruptible(jiffies_to_msecs(port->close_delay)); - spin_lock_irqsave(&port->lock, flags); + spin_lock_irq(&port->lock); } else if (!uart_console(uport)) { - spin_unlock_irqrestore(&port->lock, flags); + spin_unlock_irq(&port->lock); uart_change_pm(state, UART_PM_STATE_OFF); - spin_lock_irqsave(&port->lock, flags); + spin_lock_irq(&port->lock); } /* @@ -1437,7 +1435,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp) */ clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags); clear_bit(ASYNCB_CLOSING, &port->flags); - spin_unlock_irqrestore(&port->lock, flags); + spin_unlock_irq(&port->lock); wake_up_interruptible(&port->open_wait); wake_up_interruptible(&port->close_wait); @@ -1532,11 +1530,6 @@ static void uart_hangup(struct tty_struct *tty) mutex_unlock(&port->mutex); } -static int uart_port_activate(struct tty_port *port, struct tty_struct *tty) -{ - return 0; -} - static void uart_port_shutdown(struct tty_port *port) { struct uart_state *state = container_of(port, struct uart_state, port); @@ -2379,8 +2372,6 @@ static const struct tty_operations uart_ops = { }; static const struct tty_port_operations uart_port_ops = { - .activate = uart_port_activate, - .shutdown = uart_port_shutdown, .carrier_raised = uart_carrier_raised, .dtr_rts = uart_dtr_rts, }; diff --git a/drivers/tty/serial/sirfsoc_uart.c b/drivers/tty/serial/sirfsoc_uart.c index 653cdd5fb..c6657de78 100644 --- a/drivers/tty/serial/sirfsoc_uart.c +++ b/drivers/tty/serial/sirfsoc_uart.c @@ -413,7 +413,6 @@ sirfsoc_uart_pio_rx_chars(struct uart_port *port, unsigned int max_rx_count) break; } - sirfport->rx_io_count += rx_count; port->icount.rx += rx_count; return rx_count; @@ -600,7 +599,6 @@ static void sirfsoc_uart_start_next_rx_dma(struct uart_port *port) struct sirfsoc_uart_port *sirfport = to_sirfport(port); struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; - sirfport->rx_io_count = 0; wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) & ~SIRFUART_IO_MODE); @@ -632,31 +630,6 @@ static void sirfsoc_uart_start_next_rx_dma(struct uart_port *port) sirfport->uart_reg->uart_type)); } -static void sirfsoc_uart_start_rx(struct uart_port *port) -{ - struct sirfsoc_uart_port *sirfport = to_sirfport(port); - struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; - struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; - - sirfport->rx_io_count = 0; - wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_RESET); - wr_regl(port, ureg->sirfsoc_rx_fifo_op, 0); - wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_START); - if (sirfport->rx_dma_chan) - sirfsoc_uart_start_next_rx_dma(port); - else { - if (!sirfport->is_atlas7) - wr_regl(port, ureg->sirfsoc_int_en_reg, - rd_regl(port, ureg->sirfsoc_int_en_reg) | - SIRFUART_RX_IO_INT_EN(uint_en, - sirfport->uart_reg->uart_type)); - else - wr_regl(port, ureg->sirfsoc_int_en_reg, - SIRFUART_RX_IO_INT_EN(uint_en, - sirfport->uart_reg->uart_type)); - } -} - static unsigned int sirfsoc_usp_calc_sample_div(unsigned long set_rate, unsigned long ioclk_rate, unsigned long *sample_reg) @@ -850,7 +823,6 @@ static void sirfsoc_uart_set_termios(struct uart_port *port, rx_time_out = SIRFSOC_UART_RX_TIMEOUT(set_baud, 20000); rx_time_out = SIRFUART_RECV_TIMEOUT_VALUE(rx_time_out); txfifo_op_reg = rd_regl(port, ureg->sirfsoc_tx_fifo_op); - wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_STOP); wr_regl(port, ureg->sirfsoc_tx_fifo_op, (txfifo_op_reg & ~SIRFUART_FIFO_START)); if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { @@ -886,9 +858,13 @@ static void sirfsoc_uart_set_termios(struct uart_port *port, else wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, SIRFUART_IO_MODE); if (sirfport->rx_dma_chan) - wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, SIRFUART_DMA_MODE); + wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, + rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) & + ~SIRFUART_IO_MODE); else - wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, SIRFUART_IO_MODE); + wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, + rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) | + SIRFUART_IO_MODE); sirfport->rx_period_time = 20000000; /* Reset Rx/Tx FIFO Threshold level for proper baudrate */ if (set_baud < 1000000) @@ -902,7 +878,6 @@ static void sirfsoc_uart_set_termios(struct uart_port *port, txfifo_op_reg |= SIRFUART_FIFO_START; wr_regl(port, ureg->sirfsoc_tx_fifo_op, txfifo_op_reg); uart_update_timeout(port, termios->c_cflag, set_baud); - sirfsoc_uart_start_rx(port); wr_regl(port, ureg->sirfsoc_tx_rx_en, SIRFUART_TX_EN | SIRFUART_RX_EN); spin_unlock_irqrestore(&port->lock, flags); } @@ -921,6 +896,7 @@ static int sirfsoc_uart_startup(struct uart_port *port) { struct sirfsoc_uart_port *sirfport = to_sirfport(port); struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; + struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; unsigned int index = port->line; int ret; irq_modify_status(port->irq, IRQ_NOREQUEST, IRQ_NOAUTOEN); @@ -958,9 +934,9 @@ static int sirfsoc_uart_startup(struct uart_port *port) wr_regl(port, ureg->sirfsoc_rx_fifo_ctrl, SIRFUART_FIFO_THD(port)); if (sirfport->rx_dma_chan) wr_regl(port, ureg->sirfsoc_rx_fifo_level_chk, - SIRFUART_RX_FIFO_CHK_SC(port->line, 0x4) | - SIRFUART_RX_FIFO_CHK_LC(port->line, 0xe) | - SIRFUART_RX_FIFO_CHK_HC(port->line, 0x1b)); + SIRFUART_RX_FIFO_CHK_SC(port->line, 0x1) | + SIRFUART_RX_FIFO_CHK_LC(port->line, 0x2) | + SIRFUART_RX_FIFO_CHK_HC(port->line, 0x4)); if (sirfport->tx_dma_chan) { sirfport->tx_dma_state = TX_DMA_IDLE; wr_regl(port, ureg->sirfsoc_tx_fifo_level_chk, @@ -981,16 +957,41 @@ static int sirfsoc_uart_startup(struct uart_port *port) goto init_rx_err; } } - enable_irq(port->irq); + if (sirfport->uart_reg->uart_type == SIRF_REAL_UART && + sirfport->rx_dma_chan) + wr_regl(port, ureg->sirfsoc_swh_dma_io, + SIRFUART_CLEAR_RX_ADDR_EN); + if (sirfport->uart_reg->uart_type == SIRF_USP_UART && + sirfport->rx_dma_chan) + wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, + rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) | + SIRFSOC_USP_FRADDR_CLR_EN); if (sirfport->rx_dma_chan && !sirfport->is_hrt_enabled) { sirfport->is_hrt_enabled = true; sirfport->rx_period_time = 20000000; + sirfport->rx_last_pos = -1; + sirfport->pio_fetch_cnt = 0; sirfport->rx_dma_items.xmit.tail = sirfport->rx_dma_items.xmit.head = 0; hrtimer_start(&sirfport->hrt, ns_to_ktime(sirfport->rx_period_time), HRTIMER_MODE_REL); } + wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_START); + if (sirfport->rx_dma_chan) + sirfsoc_uart_start_next_rx_dma(port); + else { + if (!sirfport->is_atlas7) + wr_regl(port, ureg->sirfsoc_int_en_reg, + rd_regl(port, ureg->sirfsoc_int_en_reg) | + SIRFUART_RX_IO_INT_EN(uint_en, + sirfport->uart_reg->uart_type)); + else + wr_regl(port, ureg->sirfsoc_int_en_reg, + SIRFUART_RX_IO_INT_EN(uint_en, + sirfport->uart_reg->uart_type)); + } + enable_irq(port->irq); return 0; init_rx_err: @@ -1003,6 +1004,9 @@ static void sirfsoc_uart_shutdown(struct uart_port *port) { struct sirfsoc_uart_port *sirfport = to_sirfport(port); struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; + struct circ_buf *xmit; + + xmit = &sirfport->rx_dma_items.xmit; if (!sirfport->is_atlas7) wr_regl(port, ureg->sirfsoc_int_en_reg, 0); else @@ -1019,8 +1023,10 @@ static void sirfsoc_uart_shutdown(struct uart_port *port) if (sirfport->tx_dma_chan) sirfport->tx_dma_state = TX_DMA_IDLE; if (sirfport->rx_dma_chan && sirfport->is_hrt_enabled) { - while ((rd_regl(port, ureg->sirfsoc_rx_fifo_status) & - SIRFUART_RX_FIFO_MASK) > 0) + while (((rd_regl(port, ureg->sirfsoc_rx_fifo_status) & + SIRFUART_RX_FIFO_MASK) > sirfport->pio_fetch_cnt) && + !CIRC_CNT(xmit->head, xmit->tail, + SIRFSOC_RX_DMA_BUF_SIZE)) ; sirfport->is_hrt_enabled = false; hrtimer_cancel(&sirfport->hrt); @@ -1169,6 +1175,8 @@ static enum hrtimer_restart struct tty_struct *tty; struct sirfsoc_register *ureg; struct circ_buf *xmit; + struct sirfsoc_fifo_status *ufifo_st; + int max_pio_cnt; sirfport = container_of(hrt, struct sirfsoc_uart_port, hrt); port = &sirfport->port; @@ -1176,9 +1184,16 @@ static enum hrtimer_restart tty = port->state->port.tty; ureg = &sirfport->uart_reg->uart_reg; xmit = &sirfport->rx_dma_items.xmit; + ufifo_st = &sirfport->uart_reg->fifo_status; + dmaengine_tx_status(sirfport->rx_dma_chan, - sirfport->rx_dma_items.cookie, &tx_state); - xmit->head = SIRFSOC_RX_DMA_BUF_SIZE - tx_state.residue; + sirfport->rx_dma_items.cookie, &tx_state); + if (SIRFSOC_RX_DMA_BUF_SIZE - tx_state.residue != + sirfport->rx_last_pos) { + xmit->head = SIRFSOC_RX_DMA_BUF_SIZE - tx_state.residue; + sirfport->rx_last_pos = xmit->head; + sirfport->pio_fetch_cnt = 0; + } count = CIRC_CNT_TO_END(xmit->head, xmit->tail, SIRFSOC_RX_DMA_BUF_SIZE); while (count > 0) { @@ -1200,23 +1215,38 @@ static enum hrtimer_restart */ if (!inserted && !count && ((rd_regl(port, ureg->sirfsoc_rx_fifo_status) & - SIRFUART_RX_FIFO_MASK) > 0)) { + SIRFUART_RX_FIFO_MASK) > sirfport->pio_fetch_cnt)) { + dmaengine_pause(sirfport->rx_dma_chan); /* switch to pio mode */ wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) | SIRFUART_IO_MODE); - while ((rd_regl(port, ureg->sirfsoc_rx_fifo_status) & - SIRFUART_RX_FIFO_MASK) > 0) { - if (sirfsoc_uart_pio_rx_chars(port, 16) > 0) - tty_flip_buffer_push(tty->port); + /* + * UART controller SWH_DMA_IO register have CLEAR_RX_ADDR_EN + * When found changing I/O to DMA mode, it clears + * two low bits of read point; + * USP have similar FRADDR_CLR_EN bit in USP_RX_DMA_IO_CTRL. + * Fetch data out from rxfifo into DMA buffer in PIO mode, + * while switch back to DMA mode, the data fetched will override + * by DMA, as hardware have a strange behaviour: + * after switch back to DMA mode, check rxfifo status it will + * be the number PIO fetched, so record the fetched data count + * to avoid the repeated fetch + */ + max_pio_cnt = 3; + while (!(rd_regl(port, ureg->sirfsoc_rx_fifo_status) & + ufifo_st->ff_empty(port)) && max_pio_cnt--) { + xmit->buf[xmit->head] = + rd_regl(port, ureg->sirfsoc_rx_fifo_data); + xmit->head = (xmit->head + 1) & + (SIRFSOC_RX_DMA_BUF_SIZE - 1); + sirfport->pio_fetch_cnt++; } - wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_RESET); - wr_regl(port, ureg->sirfsoc_rx_fifo_op, 0); - wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_START); /* switch back to dma mode */ wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) & ~SIRFUART_IO_MODE); + dmaengine_resume(sirfport->rx_dma_chan); } next_hrt: hrtimer_forward_now(hrt, ns_to_ktime(sirfport->rx_period_time)); @@ -1239,7 +1269,7 @@ static int sirfsoc_uart_probe(struct platform_device *pdev) struct resource *res; int ret; struct dma_slave_config slv_cfg = { - .src_maxburst = 2, + .src_maxburst = 1, }; struct dma_slave_config tx_slv_cfg = { .dst_maxburst = 2, diff --git a/drivers/tty/serial/sirfsoc_uart.h b/drivers/tty/serial/sirfsoc_uart.h index eb162b012..c3a885b4d 100644 --- a/drivers/tty/serial/sirfsoc_uart.h +++ b/drivers/tty/serial/sirfsoc_uart.h @@ -296,6 +296,7 @@ struct sirfsoc_uart_register sirfsoc_uart = { #define SIRFUART_DMA_MODE 0x0 #define SIRFUART_RX_DMA_FLUSH 0x4 +#define SIRFUART_CLEAR_RX_ADDR_EN 0x2 /* Baud Rate Calculation */ #define SIRF_USP_MIN_SAMPLE_DIV 0x1 #define SIRF_MIN_SAMPLE_DIV 0xf @@ -325,6 +326,7 @@ struct sirfsoc_uart_register sirfsoc_uart = { #define SIRFSOC_USP_ASYNC_DIV2_MASK 0x3f #define SIRFSOC_USP_ASYNC_DIV2_OFFSET 16 #define SIRFSOC_USP_LOOP_BACK_CTRL BIT(2) +#define SIRFSOC_USP_FRADDR_CLR_EN BIT(1) /* USP-UART Common */ #define SIRFSOC_UART_RX_TIMEOUT(br, to) (((br) * (((to) + 999) / 1000)) / 1000) #define SIRFUART_RECV_TIMEOUT_VALUE(x) \ @@ -421,7 +423,6 @@ struct sirfsoc_uart_port { struct dma_chan *tx_dma_chan; dma_addr_t tx_dma_addr; struct dma_async_tx_descriptor *tx_dma_desc; - unsigned int rx_io_count; unsigned long transfer_size; enum sirfsoc_tx_state tx_dma_state; unsigned int cts_gpio; @@ -431,6 +432,8 @@ struct sirfsoc_uart_port { struct hrtimer hrt; bool is_hrt_enabled; unsigned long rx_period_time; + unsigned long rx_last_pos; + unsigned long pio_fetch_cnt; }; /* Register Access Control */ diff --git a/drivers/tty/serial/sn_console.c b/drivers/tty/serial/sn_console.c index 33e94e56d..d4692d888 100644 --- a/drivers/tty/serial/sn_console.c +++ b/drivers/tty/serial/sn_console.c @@ -42,7 +42,7 @@ #include #include #include -#include +#include #include #include #include @@ -659,7 +659,7 @@ static void sn_sal_timer_poll(unsigned long data) * @port: Our sn_cons_port (which contains the uart port) * * So this is used by sn_sal_serial_console_init (early on, before we're - * registered with serial core). It's also used by sn_sal_module_init + * registered with serial core). It's also used by sn_sal_init * right after we've registered with serial core. The later only happens * if we didn't already come through here via sn_sal_serial_console_init. * @@ -709,7 +709,7 @@ static void __init sn_sal_switch_to_asynch(struct sn_cons_port *port) * sn_sal_switch_to_interrupts - Switch to interrupt driven mode * @port: Our sn_cons_port (which contains the uart port) * - * In sn_sal_module_init, after we're registered with serial core and + * In sn_sal_init, after we're registered with serial core and * the port is added, this function is called to switch us to interrupt * mode. We were previously in asynch/polling mode (using init_timer). * @@ -773,7 +773,7 @@ static struct uart_driver sal_console_uart = { }; /** - * sn_sal_module_init - When the kernel loads us, get us rolling w/ serial core + * sn_sal_init - When the kernel loads us, get us rolling w/ serial core * * Before this is called, we've been printing kernel messages in a special * early mode not making use of the serial core infrastructure. When our @@ -781,7 +781,7 @@ static struct uart_driver sal_console_uart = { * core and try to enable interrupt driven mode. * */ -static int __init sn_sal_module_init(void) +static int __init sn_sal_init(void) { int retval; @@ -811,7 +811,7 @@ static int __init sn_sal_module_init(void) if (uart_register_driver(&sal_console_uart) < 0) { printk - ("ERROR sn_sal_module_init failed uart_register_driver, line %d\n", + ("ERROR sn_sal_init failed uart_register_driver, line %d\n", __LINE__); return -ENODEV; } @@ -832,33 +832,19 @@ static int __init sn_sal_module_init(void) /* when this driver is compiled in, the console initialization * will have already switched us into asynchronous operation - * before we get here through the module initcalls */ + * before we get here through the initcalls */ if (!sal_console_port.sc_is_asynch) { sn_sal_switch_to_asynch(&sal_console_port); } - /* at this point (module_init) we can try to turn on interrupts */ + /* at this point (device_init) we can try to turn on interrupts */ if (!IS_RUNNING_ON_SIMULATOR()) { sn_sal_switch_to_interrupts(&sal_console_port); } sn_process_input = 1; return 0; } - -/** - * sn_sal_module_exit - When we're unloaded, remove the driver/port - * - */ -static void __exit sn_sal_module_exit(void) -{ - del_timer_sync(&sal_console_port.sc_timer); - uart_remove_one_port(&sal_console_uart, &sal_console_port.sc_port); - uart_unregister_driver(&sal_console_uart); - misc_deregister(&misc); -} - -module_init(sn_sal_module_init); -module_exit(sn_sal_module_exit); +device_initcall(sn_sal_init); /** * puts_raw_fixed - sn_sal_console_write helper for adding \r's as required diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c index 4a6eab6da..e3de9c6d2 100644 --- a/drivers/tty/serial/stm32-usart.c +++ b/drivers/tty/serial/stm32-usart.c @@ -6,7 +6,7 @@ * Inspired by st-asc.c from STMicroelectronics (c) */ -#if defined(CONFIG_SERIAL_STM32_USART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#if defined(CONFIG_SERIAL_STM32_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) #define SUPPORT_SYSRQ #endif diff --git a/drivers/tty/serial/suncore.c b/drivers/tty/serial/suncore.c index 6e4ac8db2..127472bd6 100644 --- a/drivers/tty/serial/suncore.c +++ b/drivers/tty/serial/suncore.c @@ -10,7 +10,6 @@ * Copyright (C) 2002 David S. Miller (davem@redhat.com) */ -#include #include #include #include @@ -234,14 +233,10 @@ static int __init suncore_init(void) { return 0; } +device_initcall(suncore_init); -static void __exit suncore_exit(void) -{ -} - -module_init(suncore_init); -module_exit(suncore_exit); - +#if 0 /* ..def MODULE ; never supported as such */ MODULE_AUTHOR("Eddie C. Dost, David S. Miller"); MODULE_DESCRIPTION("Sun serial common layer"); MODULE_LICENSE("GPL"); +#endif diff --git a/drivers/tty/serial/sunhv.c b/drivers/tty/serial/sunhv.c index 534754440..064031870 100644 --- a/drivers/tty/serial/sunhv.c +++ b/drivers/tty/serial/sunhv.c @@ -3,7 +3,6 @@ * Copyright (C) 2006, 2007 David S. Miller (davem@davemloft.net) */ -#include #include #include #include @@ -621,7 +620,6 @@ static const struct of_device_id hv_match[] = { }, {}, }; -MODULE_DEVICE_TABLE(of, hv_match); static struct platform_driver hv_driver = { .driver = { @@ -639,16 +637,11 @@ static int __init sunhv_init(void) return platform_driver_register(&hv_driver); } +device_initcall(sunhv_init); -static void __exit sunhv_exit(void) -{ - platform_driver_unregister(&hv_driver); -} - -module_init(sunhv_init); -module_exit(sunhv_exit); - +#if 0 /* ...def MODULE ; never supported as such */ MODULE_AUTHOR("David S. Miller"); MODULE_DESCRIPTION("SUN4V Hypervisor console driver"); MODULE_VERSION("2.0"); MODULE_LICENSE("GPL"); +#endif diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c index a6aa334c8..3475e0e4c 100644 --- a/drivers/tty/serial/ucc_uart.c +++ b/drivers/tty/serial/ucc_uart.c @@ -950,7 +950,7 @@ static void qe_uart_set_termios(struct uart_port *port, if ((termios->c_cflag & CREAD) == 0) port->read_status_mask &= ~BD_SC_EMPTY; - baud = uart_get_baud_rate(port, termios, old, 0, 115200); + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); /* Do we really need a spinlock here? */ spin_lock_irqsave(&port->lock, flags); -- cgit v1.2.3-54-g00ecf