From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001 From: André Fabian Silva Delgado Date: Wed, 5 Aug 2015 17:04:01 -0300 Subject: Initial import --- drivers/usb/host/Kconfig | 790 +++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 790 insertions(+) create mode 100644 drivers/usb/host/Kconfig (limited to 'drivers/usb/host/Kconfig') diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig new file mode 100644 index 000000000..197a6a3e6 --- /dev/null +++ b/drivers/usb/host/Kconfig @@ -0,0 +1,790 @@ +# +# USB Host Controller Drivers +# +comment "USB Host Controller Drivers" + +config USB_C67X00_HCD + tristate "Cypress C67x00 HCD support" + help + The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role + host/peripheral/OTG USB controllers. + + Enable this option to support this chip in host controller mode. + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called c67x00. + +config USB_XHCI_HCD + tristate "xHCI HCD (USB 3.0) support" + ---help--- + The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0 + "SuperSpeed" host controller hardware. + + To compile this driver as a module, choose M here: the + module will be called xhci-hcd. + +if USB_XHCI_HCD + +config USB_XHCI_PCI + tristate + depends on PCI + default y + +config USB_XHCI_PLATFORM + tristate + +config USB_XHCI_MVEBU + tristate "xHCI support for Marvell Armada 375/38x" + select USB_XHCI_PLATFORM + depends on ARCH_MVEBU || COMPILE_TEST + ---help--- + Say 'Y' to enable the support for the xHCI host controller + found in Marvell Armada 375/38x ARM SOCs. + +config USB_XHCI_RCAR + tristate "xHCI support for Renesas R-Car SoCs" + select USB_XHCI_PLATFORM + depends on ARCH_SHMOBILE || COMPILE_TEST + ---help--- + Say 'Y' to enable the support for the xHCI host controller + found in Renesas R-Car ARM SoCs. + +endif # USB_XHCI_HCD + +config USB_EHCI_HCD + tristate "EHCI HCD (USB 2.0) support" + ---help--- + The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0 + "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware. + If your USB host controller supports USB 2.0, you will likely want to + configure this Host Controller Driver. + + EHCI controllers are packaged with "companion" host controllers (OHCI + or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports + will connect to EHCI if the device is high speed, otherwise they + connect to a companion controller. If you configure EHCI, you should + probably configure the OHCI (for NEC and some other vendors) USB Host + Controller Driver or UHCI (for Via motherboards) Host Controller + Driver too. + + You may want to read . + + To compile this driver as a module, choose M here: the + module will be called ehci-hcd. + +config USB_EHCI_ROOT_HUB_TT + bool "Root Hub Transaction Translators" + depends on USB_EHCI_HCD + ---help--- + Some EHCI chips have vendor-specific extensions to integrate + transaction translators, so that no OHCI or UHCI companion + controller is needed. It's safe to say "y" even if your + controller doesn't support this feature. + + This supports the EHCI implementation that's originally + from ARC, and has since changed hands a few times. + +config USB_EHCI_TT_NEWSCHED + bool "Improved Transaction Translator scheduling" + depends on USB_EHCI_HCD + default y + ---help--- + This changes the periodic scheduling code to fill more of the low + and full speed bandwidth available from the Transaction Translator + (TT) in USB 2.0 hubs. Without this, only one transfer will be + issued in each microframe, significantly reducing the number of + periodic low/fullspeed transfers possible. + + If you have multiple periodic low/fullspeed devices connected to a + highspeed USB hub which is connected to a highspeed USB Host + Controller, and some of those devices will not work correctly + (possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if + you have only one such device and it doesn't work, you could try + saying N. + + If unsure, say Y. + +config USB_FSL_MPH_DR_OF + tristate + +if USB_EHCI_HCD + +config USB_EHCI_PCI + tristate + depends on PCI + default y + +config USB_EHCI_HCD_PMC_MSP + tristate "EHCI support for on-chip PMC MSP71xx USB controller" + depends on MSP_HAS_USB + default n + select USB_EHCI_BIG_ENDIAN_DESC + select USB_EHCI_BIG_ENDIAN_MMIO + ---help--- + Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's. + If unsure, say N. + +config XPS_USB_HCD_XILINX + bool "Use Xilinx usb host EHCI controller core" + depends on (PPC32 || MICROBLAZE) + select USB_EHCI_BIG_ENDIAN_DESC + select USB_EHCI_BIG_ENDIAN_MMIO + ---help--- + Xilinx xps USB host controller core is EHCI compliant and has + transaction translator built-in. It can be configured to either + support both high speed and full speed devices, or high speed + devices only. + +config USB_EHCI_FSL + bool "Support for Freescale PPC on-chip EHCI USB controller" + depends on FSL_SOC + select USB_EHCI_ROOT_HUB_TT + select USB_FSL_MPH_DR_OF if OF + ---help--- + Variation of ARC USB block used in some Freescale chips. + +config USB_EHCI_MXC + tristate "Support for Freescale i.MX on-chip EHCI USB controller" + depends on ARCH_MXC + select USB_EHCI_ROOT_HUB_TT + ---help--- + Variation of ARC USB block used in some Freescale chips. + +config USB_EHCI_HCD_OMAP + tristate "EHCI support for OMAP3 and later chips" + depends on ARCH_OMAP + select NOP_USB_XCEIV + default y + ---help--- + Enables support for the on-chip EHCI controller on + OMAP3 and later chips. + +config USB_EHCI_HCD_ORION + tristate "Support for Marvell EBU on-chip EHCI USB controller" + depends on USB_EHCI_HCD && PLAT_ORION + default y + ---help--- + Enables support for the on-chip EHCI controller on Marvell's + embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP, + Armada 370. This is different from the EHCI implementation + on Marvell's mobile PXA and MMP SoC, see "EHCI support for + Marvell PXA/MMP USB controller" for those. + +config USB_EHCI_HCD_SPEAR + tristate "Support for ST SPEAr on-chip EHCI USB controller" + depends on USB_EHCI_HCD && PLAT_SPEAR + default y + ---help--- + Enables support for the on-chip EHCI controller on + ST SPEAr chips. + +config USB_EHCI_HCD_STI + tristate "Support for ST STiHxxx on-chip EHCI USB controller" + depends on ARCH_STI && OF + select GENERIC_PHY + select USB_EHCI_HCD_PLATFORM + help + Enable support for the on-chip EHCI controller found on + STMicroelectronics consumer electronics SoC's. + +config USB_EHCI_HCD_AT91 + tristate "Support for Atmel on-chip EHCI USB controller" + depends on USB_EHCI_HCD && ARCH_AT91 + default y + ---help--- + Enables support for the on-chip EHCI controller on + Atmel chips. + +config USB_EHCI_MSM + tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller" + depends on ARCH_QCOM + select USB_EHCI_ROOT_HUB_TT + ---help--- + Enables support for the USB Host controller present on the + Qualcomm chipsets. Root Hub has inbuilt TT. + This driver depends on OTG driver for PHY initialization, + clock management, powering up VBUS, and power management. + This driver is not supported on boards like trout which + has an external PHY. + +config USB_EHCI_TEGRA + tristate "NVIDIA Tegra HCD support" + depends on ARCH_TEGRA + select USB_EHCI_ROOT_HUB_TT + select USB_PHY + help + This driver enables support for the internal USB Host Controllers + found in NVIDIA Tegra SoCs. The controllers are EHCI compliant. + +config USB_EHCI_HCD_PPC_OF + bool "EHCI support for PPC USB controller on OF platform bus" + depends on PPC + default y + ---help--- + Enables support for the USB controller present on the PowerPC + OpenFirmware platform bus. + +config USB_EHCI_SH + bool "EHCI support for SuperH USB controller" + depends on SUPERH + ---help--- + Enables support for the on-chip EHCI controller on the SuperH. + If you use the PCI EHCI controller, this option is not necessary. + +config USB_EHCI_EXYNOS + tristate "EHCI support for Samsung S5P/EXYNOS SoC Series" + depends on ARCH_S5PV210 || ARCH_EXYNOS + help + Enable support for the Samsung Exynos SOC's on-chip EHCI controller. + +config USB_EHCI_MV + bool "EHCI support for Marvell PXA/MMP USB controller" + depends on (ARCH_PXA || ARCH_MMP) + select USB_EHCI_ROOT_HUB_TT + ---help--- + Enables support for Marvell (including PXA and MMP series) on-chip + USB SPH and OTG controller. SPH is a single port host, and it can + only be EHCI host. OTG is controller that can switch to host mode. + Note that this driver will not work on Marvell's other EHCI + controller used by the EBU-type SoCs including Orion, Kirkwood, + Dova, Armada 370 and Armada XP. See "Support for Marvell EBU + on-chip EHCI USB controller" for those. + +config USB_W90X900_EHCI + tristate "W90X900(W90P910) EHCI support" + depends on ARCH_W90X900 + ---help--- + Enables support for the W90X900 USB controller + +config USB_CNS3XXX_EHCI + bool "Cavium CNS3XXX EHCI Module (DEPRECATED)" + depends on ARCH_CNS3XXX + select USB_EHCI_HCD_PLATFORM + ---help--- + This option is deprecated now and the driver was removed, use + USB_EHCI_HCD_PLATFORM instead. + + Enable support for the CNS3XXX SOC's on-chip EHCI controller. + It is needed for high-speed (480Mbit/sec) USB 2.0 device + support. + +config USB_EHCI_ATH79 + bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)" + depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X) + select USB_EHCI_ROOT_HUB_TT + select USB_EHCI_HCD_PLATFORM + default y + ---help--- + This option is deprecated now and the driver was removed, use + USB_EHCI_HCD_PLATFORM instead. + + Enables support for the built-in EHCI controller present + on the Atheros AR7XXX/AR9XXX SoCs. + +config USB_EHCI_HCD_PLATFORM + tristate "Generic EHCI driver for a platform device" + default n + ---help--- + Adds an EHCI host driver for a generic platform device, which + provides a memory space and an irq. + + If unsure, say N. + +config USB_OCTEON_EHCI + bool "Octeon on-chip EHCI support (DEPRECATED)" + depends on CAVIUM_OCTEON_SOC + default n + select USB_EHCI_BIG_ENDIAN_MMIO + select USB_EHCI_HCD_PLATFORM + help + This option is deprecated now and the driver was removed, use + USB_EHCI_HCD_PLATFORM instead. + + Enable support for the Octeon II SOC's on-chip EHCI + controller. It is needed for high-speed (480Mbit/sec) + USB 2.0 device support. All CN6XXX based chips with USB are + supported. + +endif # USB_EHCI_HCD + +config USB_OXU210HP_HCD + tristate "OXU210HP HCD support" + ---help--- + The OXU210HP is an USB host/OTG/device controller. Enable this + option if your board has this chip. If unsure, say N. + + This driver does not support isochronous transfers and doesn't + implement OTG nor USB device controllers. + + To compile this driver as a module, choose M here: the + module will be called oxu210hp-hcd. + +config USB_ISP116X_HCD + tristate "ISP116X HCD support" + ---help--- + The ISP1160 and ISP1161 chips are USB host controllers. Enable this + option if your board has this chip. If unsure, say N. + + This driver does not support isochronous transfers. + + To compile this driver as a module, choose M here: the + module will be called isp116x-hcd. + +config USB_ISP1362_HCD + tristate "ISP1362 HCD support" + ---help--- + Supports the Philips ISP1362 chip as a host controller + + This driver does not support isochronous transfers. + + To compile this driver as a module, choose M here: the + module will be called isp1362-hcd. + +config USB_FUSBH200_HCD + tristate "FUSBH200 HCD support" + depends on USB + ---help--- + Faraday FUSBH200 is designed to meet USB2.0 EHCI specification + with minor modification. + + To compile this driver as a module, choose M here: the + module will be called fusbh200-hcd. + +config USB_FOTG210_HCD + tristate "FOTG210 HCD support" + depends on USB + ---help--- + Faraday FOTG210 is an OTG controller which can be configured as + an USB2.0 host. It is designed to meet USB2.0 EHCI specification + with minor modification. + + To compile this driver as a module, choose M here: the + module will be called fotg210-hcd. + +config USB_MAX3421_HCD + tristate "MAX3421 HCD (USB-over-SPI) support" + depends on USB && SPI + ---help--- + The Maxim MAX3421E chip supports standard USB 2.0-compliant + full-speed devices either in host or peripheral mode. This + driver supports the host-mode of the MAX3421E only. + + To compile this driver as a module, choose M here: the module will + be called max3421-hcd. + +config USB_OHCI_HCD + tristate "OHCI HCD (USB 1.1) support" + ---help--- + The Open Host Controller Interface (OHCI) is a standard for accessing + USB 1.1 host controller hardware. It does more in hardware than Intel's + UHCI specification. If your USB host controller follows the OHCI spec, + say Y. On most non-x86 systems, and on x86 hardware that's not using a + USB controller from Intel or VIA, this is appropriate. If your host + controller doesn't use PCI, this is probably appropriate. For a PCI + based system where you're not sure, the "lspci -v" entry will list the + right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI. + + To compile this driver as a module, choose M here: the + module will be called ohci-hcd. + +if USB_OHCI_HCD + +config USB_OHCI_HCD_OMAP1 + tristate "OHCI support for OMAP1/2 chips" + depends on ARCH_OMAP1 + depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3) + default y + ---help--- + Enables support for the OHCI controller on OMAP1/2 chips. + +config USB_OHCI_HCD_SPEAR + tristate "Support for ST SPEAr on-chip OHCI USB controller" + depends on USB_OHCI_HCD && PLAT_SPEAR + default y + ---help--- + Enables support for the on-chip OHCI controller on + ST SPEAr chips. + +config USB_OHCI_HCD_STI + tristate "Support for ST STiHxxx on-chip OHCI USB controller" + depends on ARCH_STI && OF + select GENERIC_PHY + select USB_OHCI_HCD_PLATFORM + help + Enable support for the on-chip OHCI controller found on + STMicroelectronics consumer electronics SoC's. + +config USB_OHCI_HCD_S3C2410 + tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series" + depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX) + default y + ---help--- + Enables support for the on-chip OHCI controller on + S3C24xx/S3C64xx chips. + +config USB_OHCI_HCD_LPC32XX + tristate "Support for LPC on-chip OHCI USB controller" + depends on USB_OHCI_HCD && ARCH_LPC32XX + depends on USB_ISP1301 + default y + ---help--- + Enables support for the on-chip OHCI controller on + NXP chips. + +config USB_OHCI_HCD_PXA27X + tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller" + depends on USB_OHCI_HCD && (PXA27x || PXA3xx) + default y + ---help--- + Enables support for the on-chip OHCI controller on + PXA27x/PXA3xx chips. + +config USB_OHCI_HCD_AT91 + tristate "Support for Atmel on-chip OHCI USB controller" + depends on USB_OHCI_HCD && ARCH_AT91 + default y + ---help--- + Enables support for the on-chip OHCI controller on + Atmel chips. + +config USB_OHCI_HCD_OMAP3 + tristate "OHCI support for OMAP3 and later chips" + depends on (ARCH_OMAP3 || ARCH_OMAP4) + default y + ---help--- + Enables support for the on-chip OHCI controller on + OMAP3 and later chips. + +config USB_OHCI_HCD_DAVINCI + bool "OHCI support for TI DaVinci DA8xx" + depends on ARCH_DAVINCI_DA8XX + depends on USB_OHCI_HCD=y + default y + help + Enables support for the DaVinci DA8xx integrated OHCI + controller. This driver cannot currently be a loadable + module because it lacks a proper PHY abstraction. + +config USB_OHCI_ATH79 + bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)" + depends on (SOC_AR71XX || SOC_AR724X) + select USB_OHCI_HCD_PLATFORM + default y + help + This option is deprecated now and the driver was removed, use + USB_OHCI_HCD_PLATFORM instead. + + Enables support for the built-in OHCI controller present on the + Atheros AR71XX/AR7240 SoCs. + +config USB_OHCI_HCD_PPC_OF_BE + bool "OHCI support for OF platform bus (big endian)" + depends on PPC + select USB_OHCI_BIG_ENDIAN_DESC + select USB_OHCI_BIG_ENDIAN_MMIO + ---help--- + Enables support for big-endian USB controllers present on the + OpenFirmware platform bus. + +config USB_OHCI_HCD_PPC_OF_LE + bool "OHCI support for OF platform bus (little endian)" + depends on PPC + select USB_OHCI_LITTLE_ENDIAN + ---help--- + Enables support for little-endian USB controllers present on the + OpenFirmware platform bus. + +config USB_OHCI_HCD_PPC_OF + bool + depends on PPC + default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE + +config USB_OHCI_HCD_PCI + tristate "OHCI support for PCI-bus USB controllers" + depends on PCI + default y + select USB_OHCI_LITTLE_ENDIAN + ---help--- + Enables support for PCI-bus plug-in USB controller cards. + If unsure, say Y. + +config USB_OHCI_HCD_SSB + bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)" + depends on (SSB = y || SSB = USB_OHCI_HCD) + select USB_HCD_SSB + select USB_OHCI_HCD_PLATFORM + default n + ---help--- + This option is deprecated now and the driver was removed, use + USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead. + + Support for the Sonics Silicon Backplane (SSB) attached + Broadcom USB OHCI core. + + This device is present in some embedded devices with + Broadcom based SSB bus. + + If unsure, say N. + +config USB_OHCI_SH + bool "OHCI support for SuperH USB controller (DEPRECATED)" + depends on SUPERH + select USB_OHCI_HCD_PLATFORM + ---help--- + This option is deprecated now and the driver was removed, use + USB_OHCI_HCD_PLATFORM instead. + + Enables support for the on-chip OHCI controller on the SuperH. + If you use the PCI OHCI controller, this option is not necessary. + +config USB_OHCI_EXYNOS + tristate "OHCI support for Samsung S5P/EXYNOS SoC Series" + depends on ARCH_S5PV210 || ARCH_EXYNOS + help + Enable support for the Samsung Exynos SOC's on-chip OHCI controller. + +config USB_CNS3XXX_OHCI + bool "Cavium CNS3XXX OHCI Module (DEPRECATED)" + depends on ARCH_CNS3XXX + select USB_OHCI_HCD_PLATFORM + ---help--- + This option is deprecated now and the driver was removed, use + USB_OHCI_HCD_PLATFORM instead. + + Enable support for the CNS3XXX SOC's on-chip OHCI controller. + It is needed for low-speed USB 1.0 device support. + +config USB_OHCI_HCD_PLATFORM + tristate "Generic OHCI driver for a platform device" + default n + ---help--- + Adds an OHCI host driver for a generic platform device, which + provides a memory space and an irq. + + If unsure, say N. + +config USB_OCTEON_OHCI + bool "Octeon on-chip OHCI support (DEPRECATED)" + depends on CAVIUM_OCTEON_SOC + default USB_OCTEON_EHCI + select USB_OHCI_BIG_ENDIAN_MMIO + select USB_OHCI_LITTLE_ENDIAN + select USB_OHCI_HCD_PLATFORM + help + This option is deprecated now and the driver was removed, use + USB_OHCI_HCD_PLATFORM instead. + + Enable support for the Octeon II SOC's on-chip OHCI + controller. It is needed for low-speed USB 1.0 device + support. All CN6XXX based chips with USB are supported. + +endif # USB_OHCI_HCD + +config USB_UHCI_HCD + tristate "UHCI HCD (most Intel and VIA) support" + depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC + ---help--- + The Universal Host Controller Interface is a standard by Intel for + accessing the USB hardware in the PC (which is also called the USB + host controller). If your USB host controller conforms to this + standard, you may want to say Y, but see below. All recent boards + with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX, + i810, i820) conform to this standard. Also all VIA PCI chipsets + (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro + 133) and LEON/GRLIB SoCs with the GRUSBHC controller. + If unsure, say Y. + + To compile this driver as a module, choose M here: the + module will be called uhci-hcd. + +config USB_UHCI_SUPPORT_NON_PCI_HC + bool + default y if (SPARC_LEON || USB_UHCI_PLATFORM) + +config USB_UHCI_PLATFORM + bool + default y if ARCH_VT8500 + +config USB_UHCI_BIG_ENDIAN_MMIO + bool + default y if SPARC_LEON + +config USB_UHCI_BIG_ENDIAN_DESC + bool + default y if SPARC_LEON + +config USB_FHCI_HCD + tristate "Freescale QE USB Host Controller support" + depends on OF_GPIO && QE_GPIO && QUICC_ENGINE + select FSL_GTM + select QE_USB + help + This driver enables support for Freescale QE USB Host Controller + (as found on MPC8360 and MPC8323 processors), the driver supports + Full and Low Speed USB. + +config FHCI_DEBUG + bool "Freescale QE USB Host Controller debug support" + depends on USB_FHCI_HCD && DEBUG_FS + help + Say "y" to see some FHCI debug information and statistics + through debugfs. + +config USB_U132_HCD + tristate "Elan U132 Adapter Host Controller" + depends on USB_FTDI_ELAN + help + The U132 adapter is a USB to CardBus adapter specifically designed + for PC cards that contain an OHCI host controller. Typical PC cards + are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132 + adapter will *NOT* work with PC cards that do not contain an OHCI + controller. + + For those PC cards that contain multiple OHCI controllers only the + first one is used. + + The driver consists of two modules, the "ftdi-elan" module is a + USB client driver that interfaces to the FTDI chip within ELAN's + USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host + controller driver that talks to the OHCI controller within the + CardBus cards that are inserted in the U132 adapter. + + This driver has been tested with a CardBus OHCI USB adapter, and + worked with a USB PEN Drive inserted into the first USB port of + the PCCARD. A rather pointless thing to do, but useful for testing. + + It is safe to say M here. + + See also + +config USB_SL811_HCD + tristate "SL811HS HCD support" + help + The SL811HS is a single-port USB controller that supports either + host side or peripheral side roles. Enable this option if your + board has this chip, and you want to use it as a host controller. + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called sl811-hcd. + +config USB_SL811_HCD_ISO + bool "partial ISO support" + depends on USB_SL811_HCD + help + The driver doesn't support iso_frame_desc (yet), but for some simple + devices that just queue one ISO frame per URB, then ISO transfers + "should" work using the normal urb status fields. + + If unsure, say N. + +config USB_SL811_CS + tristate "CF/PCMCIA support for SL811HS HCD" + depends on USB_SL811_HCD && PCMCIA + help + Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC + REX-CFU1U CF card (often used with PDAs). If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called "sl811_cs". + +config USB_R8A66597_HCD + tristate "R8A66597 HCD support" + help + The R8A66597 is a USB 2.0 host and peripheral controller. + + Enable this option if your board has this chip, and you want + to use it as a host controller. If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called r8a66597-hcd. + +config USB_RENESAS_USBHS_HCD + tristate "Renesas USBHS HCD support" + depends on USB_RENESAS_USBHS + help + The Renesas USBHS is a USB 2.0 host and peripheral controller. + + Enable this option if your board has this chip, and you want + to use it as a host controller. If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called renesas-usbhs. + +config USB_WHCI_HCD + tristate "Wireless USB Host Controller Interface (WHCI) driver" + depends on PCI && USB && UWB + select USB_WUSB + select UWB_WHCI + help + A driver for PCI-based Wireless USB Host Controllers that are + compliant with the WHCI specification. + + To compile this driver a module, choose M here: the module + will be called "whci-hcd". + +config USB_HWA_HCD + tristate "Host Wire Adapter (HWA) driver" + depends on USB && UWB + select USB_WUSB + select UWB_HWA + help + This driver enables you to connect Wireless USB devices to + your system using a Host Wire Adaptor USB dongle. This is an + UWB Radio Controller and WUSB Host Controller connected to + your machine via USB (specified in WUSB1.0). + + To compile this driver a module, choose M here: the module + will be called "hwa-hc". + +config USB_IMX21_HCD + tristate "i.MX21 HCD support" + depends on ARM && ARCH_MXC + help + This driver enables support for the on-chip USB host in the + i.MX21 processor. + + To compile this driver as a module, choose M here: the + module will be called "imx21-hcd". + +config USB_HCD_BCMA + tristate "BCMA usb host driver" + depends on BCMA + select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD + select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD + help + Enable support for the EHCI and OCHI host controller on an bcma bus. + It converts the bcma driver into two platform device drivers + for ehci and ohci. + + If unsure, say N. + +config USB_HCD_SSB + tristate "SSB usb host driver" + depends on SSB + select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD + select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD + help + Enable support for the EHCI and OCHI host controller on an bcma bus. + It converts the bcma driver into two platform device drivers + for ehci and ohci. + + If unsure, say N. + +config USB_HCD_TEST_MODE + bool "HCD test mode support" + ---help--- + Say 'Y' to enable additional software test modes that may be + supported by the host controller drivers. + + One such test mode is the Embedded High-speed Host Electrical Test + (EHSET) for EHCI host controller hardware, specifically the "Single + Step Set Feature" test. Typically this will be enabled for On-the-Go + or embedded hosts that need to undergo USB-IF compliance testing with + the aid of special testing hardware. In the future, this may expand + to include other tests that require support from a HCD driver. + + This option is of interest only to developers who need to validate + their USB hardware designs. It is not needed for normal use. If + unsure, say N. -- cgit v1.2.3-54-g00ecf