From 57f0f512b273f60d52568b8c6b77e17f5636edc0 Mon Sep 17 00:00:00 2001
From: André Fabian Silva Delgado <emulatorman@parabola.nu>
Date: Wed, 5 Aug 2015 17:04:01 -0300
Subject: Initial import

---
 include/linux/platform_data/atmel.h | 97 +++++++++++++++++++++++++++++++++++++
 1 file changed, 97 insertions(+)
 create mode 100644 include/linux/platform_data/atmel.h

(limited to 'include/linux/platform_data/atmel.h')

diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h
new file mode 100644
index 000000000..4b452c6a2
--- /dev/null
+++ b/include/linux/platform_data/atmel.h
@@ -0,0 +1,97 @@
+/*
+ * atmel platform data
+ *
+ * GPL v2 Only
+ */
+
+#ifndef __ATMEL_H__
+#define __ATMEL_H__
+
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/usb/atmel_usba_udc.h>
+#include <linux/atmel-mci.h>
+#include <sound/atmel-ac97c.h>
+#include <linux/serial.h>
+#include <linux/platform_data/macb.h>
+
+/*
+ * at91: 6 USARTs and one DBGU port (SAM9260)
+ * avr32: 4
+ */
+#define ATMEL_MAX_UART	7
+
+ /* USB Device */
+struct at91_udc_data {
+	int	vbus_pin;		/* high == host powering us */
+	u8	vbus_active_low;	/* vbus polarity */
+	u8	vbus_polled;		/* Use polling, not interrupt */
+	int	pullup_pin;		/* active == D+ pulled up */
+	u8	pullup_active_low;	/* true == pullup_pin is active low */
+};
+
+ /* Compact Flash */
+struct at91_cf_data {
+	int	irq_pin;		/* I/O IRQ */
+	int	det_pin;		/* Card detect */
+	int	vcc_pin;		/* power switching */
+	int	rst_pin;		/* card reset */
+	u8	chipselect;		/* EBI Chip Select number */
+	u8	flags;
+#define AT91_CF_TRUE_IDE	0x01
+#define AT91_IDE_SWAP_A0_A2	0x02
+};
+
+ /* USB Host */
+#define AT91_MAX_USBH_PORTS	3
+struct at91_usbh_data {
+	int		vbus_pin[AT91_MAX_USBH_PORTS];	/* port power-control pin */
+	int             overcurrent_pin[AT91_MAX_USBH_PORTS];
+	u8		ports;				/* number of ports on root hub */
+	u8              overcurrent_supported;
+	u8              vbus_pin_active_low[AT91_MAX_USBH_PORTS];
+	u8              overcurrent_status[AT91_MAX_USBH_PORTS];
+	u8              overcurrent_changed[AT91_MAX_USBH_PORTS];
+};
+
+ /* NAND / SmartMedia */
+struct atmel_nand_data {
+	int		enable_pin;		/* chip enable */
+	int		det_pin;		/* card detect */
+	int		rdy_pin;		/* ready/busy */
+	u8		rdy_pin_active_low;	/* rdy_pin value is inverted */
+	u8		ale;			/* address line number connected to ALE */
+	u8		cle;			/* address line number connected to CLE */
+	u8		bus_width_16;		/* buswidth is 16 bit */
+	u8		ecc_mode;		/* ecc mode */
+	u8		on_flash_bbt;		/* bbt on flash */
+	struct mtd_partition *parts;
+	unsigned int	num_parts;
+	bool		has_dma;		/* support dma transfer */
+
+	/* default is false, only for at32ap7000 chip is true */
+	bool		need_reset_workaround;
+};
+
+ /* Serial */
+struct atmel_uart_data {
+	int			num;		/* port num */
+	short			use_dma_tx;	/* use transmit DMA? */
+	short			use_dma_rx;	/* use receive DMA? */
+	void __iomem		*regs;		/* virt. base address, if any */
+	struct serial_rs485	rs485;		/* rs485 settings */
+};
+
+/* CAN */
+struct at91_can_data {
+	void (*transceiver_switch)(int on);
+};
+
+/* FIXME: this needs a better location, but gets stuff building again */
+extern int at91_suspend_entering_slow_clock(void);
+
+#endif /* __ATMEL_H__ */
-- 
cgit v1.2.3-54-g00ecf