1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
/*
* Copyright 2012 ST-Ericsson AB
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include <dt-bindings/interrupt-controller/irq.h>
/ {
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
pinctrl-names = "default";
pinctrl-0 = <&prox_stuib_mode>, <&hall_stuib_mode>;
button@139 {
/* Proximity sensor */
gpios = <&gpio6 25 0x4>;
linux,code = <11>; /* SW_FRONT_PROXIMITY */
label = "SFH7741 Proximity Sensor";
};
button@145 {
/* Hall sensor */
gpios = <&gpio4 17 0x4>;
linux,code = <0>; /* SW_LID */
label = "HED54XXU11 Hall Effect Sensor";
};
};
soc {
i2c@80004000 {
stmpe1601: stmpe1601@40 {
compatible = "st,stmpe1601";
reg = <0x40>;
interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
interrupt-parent = <&gpio6>;
interrupt-controller;
vcc-supply = <&db8500_vsmps2_reg>;
vio-supply = <&db8500_vsmps2_reg>;
wakeup-source;
st,autosleep-timeout = <1024>;
stmpe_keypad {
compatible = "st,stmpe-keypad";
debounce-interval = <64>;
st,scan-count = <8>;
st,no-autorepeat;
linux,keymap = <0x205006b
0x4010074
0x3050072
0x1030004
0x502006a
0x500000a
0x5008b
0x706001c
0x405000b
0x6070003
0x3040067
0x303006c
0x60400e7
0x602009e
0x4020073
0x5050002
0x4030069
0x3020008>;
};
};
};
/* Sensors mounted on this board variant */
i2c@80128000 {
lis331dl@1c {
/* Accelerometer */
compatible = "st,lis331dl-accel";
st,drdy-int-pin = <1>;
reg = <0x1c>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&accel_stuib_mode>;
interrupt-parent = <&gpio2>;
interrupts = <18 IRQ_TYPE_EDGE_RISING>,
<19 IRQ_TYPE_EDGE_RISING>;
};
ak8974@0f {
/* Magnetometer */
compatible = "asahi-kasei,ak8974";
reg = <0x0f>;
vdd-supply = <&ab8500_ldo_aux1_reg>;
vddio-supply = <&db8500_vsmps2_reg>;
pinctrl-names = "default";
pinctrl-0 = <&magneto_stuib_mode>;
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_EDGE_RISING>;
};
};
i2c@80110000 {
bu21013_tp@5c {
compatible = "rohm,bu21013_tp";
reg = <0x5c>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
rohm,touch-max-x = <384>;
rohm,touch-max-y = <704>;
rohm,flip-y;
};
bu21013_tp@5d {
compatible = "rohm,bu21013_tp";
reg = <0x5d>;
avdd-supply = <&ab8500_ldo_aux1_reg>;
rohm,touch-max-x = <384>;
rohm,touch-max-y = <704>;
rohm,flip-y;
};
};
pinctrl {
prox {
prox_stuib_mode: prox_stuib {
stuib_cfg {
pins = "GPIO217_AH12";
ste,config = <&gpio_in_pu>;
};
};
};
hall {
hall_stuib_mode: stuib_tvk {
stuib_cfg {
pins = "GPIO145_C13";
ste,config = <&gpio_in_pu>;
};
};
};
accelerometer {
accel_stuib_mode: accel_stuib {
/* Accelerometer interrupt lines 1 & 2 */
stuib_cfg {
pins = "GPIO82_C1", "GPIO83_D3";
ste,config = <&gpio_in_pu>;
};
};
};
magnetometer {
magneto_stuib_mode: magneto_stuib {
/* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
stuib_cfg1 {
pins = "GPIO31_V3";
ste,config = <&gpio_in_pu>;
};
stuib_cfg2 {
pins = "GPIO32_V2";
ste,config = <&gpio_in_pd>;
};
};
};
};
};
};
|
