| Age | Commit message (Collapse) | Author |
|---|
|
messages
This means the API can stay the same as for single-part messages by simply passing the head message around. Unrefing
the head of the linked list unrefs the whole list.
|
|
|
|
The kernel may broadcast such messages, simply discard them.
|
|
The data in the PCI ids file is randomly inconsistent. Many
subvendor model strings just describe the "product" where the
hardware is built into, not the hardware itself. This causes
some "Network Card Model Foo" to show up as "Laptop Model Bar".
Try to make the best out of this mess and concatenate both
strings to describe the hardware.
|
|
|
|
The kernel can return pretty much anything there, even though the fd is
closed. Let's not get confused by that.
|
|
|
|
patch the sender address
Otherwise old libdbus1 is confused and will not accept our replies.
|
|
Previously, AddMatch/RemoveMatch calls where processed exclusively in
the proxy. That's racy however, since subscribing to a signal might not
complete before the signal is sent due to some subsequent method call.
Hence, in order to expose the same ordering guarantees as dbus1 process
the AddMatch/RemoveMatch calls from the proxy, so that they are
dispatched synchronously to all following messages, thus fixing the
race.
Ultimately, we should probabably dissolve the driver entirely into the
proxy, as it is purely a compatibility feature anyway...
|
|
necessarily monotonically increasing
|
|
|
|
|
|
|
|
|
|
The way the kernel namespaces have been implemented breaks assumptions
udev made regarding uevent sequence numbers. Creating devices in a
namespace "steals" uevents and its sequence numbers from the host. It
confuses the "udevadmin settle" logic, which might block until util a
timeout is reached, even when no uevent is pending.
Remove any assumptions about sequence numbers and deprecate libudev's
API exposing these numbers; none of that can reliably be used anymore
when namespaces are involved.
|
|
|
|
In contrast to a filename-only argument, find_binary() did not
actually check if an path exists, allowing the code to fail later on.
This was OK, but it seems nicer to treat both paths identically.
Also take advantage of path_make_absolute_cwd doing strdup() by itself
if necessary to simplify.
|
|
Modifies find_binary() to accept NULL in the second argument.
fsck.type lookup logic moved to new fsck_exists() function, with a test.
|
|
|
|
|
|
|
|
If a persistent timer has no stamp file yet, it behaves just like a normal
timer until it runs for the first time. If the system is always shut down
while the timer is supposed to run, a stamp file is never created and
Peristent=true has no effect.
This patch fixes this by creating a stamp file with the current time
when the timer is first started.
|
|
... it turns out that the duplicates in our own catalog were not real
duplicates, but translations.
|
|
- Negative/positive errno mixup caused duplicates not to be detected properly.
Now we get a warning about some duplicate entries in our own catalogs...
- Errors in update_catalog would be ignored, but they should not be.
|
|
Also unref client objects in test code, and initalize logging,
to DEBUG by default.
|
|
greedy_realloc() and greedy_realloc0() now store the allocated
size as the count, not bytes.
Replace GREEDY_REALLOC uses with GREEDY_REALLOC_T everywhere,
and then rename GREEDY_REALLOC_T to GREEDY_REALLOC. It is just
too error-prone to have two slightly different macros which do the
same thing.
|
|
Usually RUNNING implies LOWER_UP, but for drivers that don't support oper state, RUNNING can
also mean that the state is unknown. In that case we should just trust LOWER_UP directly.
|
|
The interface is not fully ready until it enterns RUNNING. This was causing
problems with sending out DHCP messages before the interface was ready, so they
would get lost. In particular this affected DHCP INIT-REBOOT, as it relies on
the first package sent being successful (or it will fall back to a full reboot).
Also improve the logging a lot, to make future debugging of link state a lot
easier.
|
|
These are redundant now that the REQUEST messages contain the same information.
|
|
Specify what kind of REQUEST we send, and distinguish between REBOOT and START.
Also log stop reasons as strings rather than numbers.
|
|
|
|
This error should never happen, so replace the check with an assert. The check
was anyway broken due to an uninitialized return value.
Reported by Thomas Hindoe Paaboel Andersen <phomes@gmail.com>.
|
|
Also reshuffle some code to make the correspondence with the RFC a bit more
obvious.
Small functional change: fail if we try to send a message from the wrong state.
|
|
|
|
As we are now filtering the raw socket based on the transaction id, we must
reset the BPF when we reset the transaction id.
|
|
Add an explicit stop state for IPv4LL so that the user can stop the
IPv4LL client from the callback. When returning from the callback,
check also the stop state in order to halt any further protocol
processing.
|
|
Similar to DHCP, the IPv4LL library user can decide to free the LL
client any time the callback is called. Guard against freeing the
LL client in the callback by introducing proper reference counting.
Also update code using the IPv4LL library to properly handle a
returned NULL from the notify and stop functions if the IPv4LL
client was freed.
|
|
Add an explicit stop state for the DHCP client so that the library
user can issue a stop at any time the callback has been called.
When returning from the callback, check also the stop state and
stop any further DHCP processing.
|
|
The DHCP library user can decide to free the DHCP client any time
the callback is called. After the callback has been called, other
computations may still be needed - the best example being a full
restart of the DHCP procedure in case of lease expiry.
Fix this by introducing proper reference counting. Properly handle
a returned NULL from the notify and stop functions if the DHCP
client was freed.
|
|
|
|
This unifies the socket handling with other sd-* libraries.
|
|
|
|
|
|
|
|
|
|
We still only return the first message part in callback/synchronous calls.
|
|
|
|
This test should have been updated when changing the magic cookie handling around.
Reported by Ken MacLeod.
|
|
change_uid_gid() never initialises sz which may cause greedy_realloc to
skip the initial buffer allocation.
|
|
systemd-machined doesn't store cgroup path in a state file anymore.
Let's figure it out from the scope.
|
