| Age | Commit message (Collapse) | Author |
|---|
|
As we default to "hardware clock is in UTC" if /etc/adjtime is not present, it
also makes sense to have that default if /etc/adjtime contains only one or two
lines.
Drop the "gibberish" test case, as this was just EIO because of not containing
three lines, which is already contained in other tests. clock_is_localtime()
never actually validated the format of the first two lines, and there is little
point in doing that.
This addresses the reading half of issue #2638.
|
|
Add path argument to clock_is_localtime() and default to "/etc/adjtime" if it's
NULL. This makes the function testable.
Add test-clock: initial test cases for some scenarios, using a temporary file.
This also checks the behaviour with a NULL (i. e. the system's /etc/adjtime)
file.
|
|
tree-wide: merge pager_open_if_enabled() to the pager_open()
|
|
Many subsystems define own pager_open_if_enabled() function which
checks '--no-pager' command line argument and open pager depends
on its value. All implementations of pager_open_if_enabled() are
the same. Let's merger this function with pager_open() from the
shared/pager.c and remove pager_open_if_enabled() from all subsytems
to prevent code duplication.
|
|
sd-dhcp-server: Send replies to BOOTP relay server port
|
|
RFC 2131 Section 4.1 says that
"If the ’giaddr’ field in a DHCP message from a client is non-zero,
the server sends any return messages to the ’DHCP server’ port on the
BOOTP relay agent whose address appears in ’giaddr’."
Fix this by adding a destination port when sending unicast UDP packets
and provide the server port when a BOOTP relay agent is being used.
|
|
treewide: fix typos and then/that use
|
|
|
|
tests: various fixes
|
|
dnssec: only run tests that require gcrypt if we have it
|
|
man: clarify unit ordering language
|
|
|
|
|
|
tree-wide: minor formatting inconsistency cleanups
|
|
|
|
Bugfix set virt=none when running on XEN Dom0
|
|
When running in XEN Dom0 the virtualization check:
1) detect_xen returns HYPERVISOR_NONE so next checks are executed
2) /proc/sys/hypervisor detects a XEN hypervisor
it is lacking the special Dom0 detection as in detect_xen
With this patch, at the end of all virtualization checks we double-check if running in XEN Dom0 or DomU.
|
|
print out every single detection executed and its result.
|
|
Misc cleanup
|
|
|
|
|
|
|
|
Remove systemd-bootchart
|
|
|
|
|
|
So far we recommended placing "nss-mymachines" after "nss-resolve" in the order
of preference in /etc/nsswitch.conf. This change reverse this order.
Rationale: single-label names are resolved via LLMNR by resolved, which has to
time out if no peer by that name exists. By placing "nss-mymachines" first
(which always responds immediately) we avoid running into this timeout for most
containers. Both modules should return the same data if LLMNR is used by the
container anyway.
While we are at it, improve the man pages of the three NSS modules in other
ways a bit.
|
|
This is a follow-up to 70d7aea5c
|
|
This is a follow-up to cc3ddc851
|
|
|
|
This is a follow-up to 2525499
|
|
journal: restore offline state on error
|
|
Networkctl prettification
|
|
|
|
|
|
|
|
|
|
|
|
Better to use the mirror manager and https.
|
|
This was only needed for bootchart, so it can go now.
|
|
This commit rips out systemd-bootchart. It will be given a new home, outside
of the systemd repository. The code itself isn't actually specific to
systemd and can be used without systemd even, so let's put it somewhere
else.
|
|
tree-wide: make ++/-- usage consistent WRT spacing
|
|
network: minor manpage clarifications
|
|
Personality fixes
|
|
Throughout the tree there's spurious use of spaces separating ++ and --
operators from their respective operands. Make ++ and -- operator
consistent with the majority of existing uses; discard the spaces.
|
|
If we fail to create the thread, technically we should leave the
offline_state as OFFLINE_JOINED, not OFFLINE_SYNCING.
|
|
Lenovo T460 and P50 touchpad axis corrections
|
|
udevadm test-builtin can be very useful for testing .link files, so add a reference.
Addresses issue #2406.
|
|
Make it clear that we are talking of links (in the sense used in networkd) and not ports.
Addresses issue #964.
|
|
Enabling router advertisement may even trigger SLAAC or DHCPv6 to be used to configure
IPv6 addresses on the link. It may not be obvious that only in the SLAAC case will the
Token have an effect. Clarify this in the man page.
Addresses issue #863.
|
|
|
