| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
Same as 1e158d273.
|
|
|
|
|
|
This adds a simple generator that is capable of automatically
discovering certain GPT partitions by their type UUID and mount/enable
them. This currently covers swap partitions and /home partitions, but is
expected to grow more features soon.
This currently doesn't handle LUKS encrypted /home.
This enables all swap partitions of type
0657fd6da4ab43c484e50933c84b4f4f, if found.
This mounts the first partition of type 933ac7e12eb44f13b8440e14e2aef915
as /home, if it is found.
|
|
|
|
So far, we would show up to 128 bytes from a message, simply
cutting of the rest. With multiline messages, it is quite common
for a message to be longer than that, and this model doesn't really
work anymore.
A new limit is added: up to 3 lines will be shown, unless --full is
used (c.f. first line below). The limit for bytes is extended to 300
bytes. An ellipsis will always be used, if some form of truncation
occurs. If the tail of the message is cut off, either because of
length or line limit, dots will be shown at the end of the last
line. If this last line is short, the dots will be simply appended. If
the last line is too long for that, it will be ellipsized with dots at
the very end.
Note that the limits are in bytes, not characters, and we suck at
outputting unicode strings (c.f. last three lines below).
Aug 11 10:46:21 fedora python[67]: test message
line
line...
Aug 11 10:50:47 fedora python[76]: test message word word word word word word word word word word word wor...
Aug 11 10:55:11 fedora python[83]: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx...
Aug 11 11:03:21 fedora python[90]: ąąąąąąąąąąąąąąąąąąąąąąąąąąąąąą...
Aug 11 11:03:53 fedora python[97]: aąąąąąąąąąąąąąąąąąąąąąąąąąąąąąą...
Aug 11 11:25:45 fedora python[121]: aąąąąąąąąąąąąąąąąąąąąąąąąąąąąąąąąąą�...
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
reply
https://bugs.freedesktop.org/show_bug.cgi?id=67273
|
|
"systemctl set-log-level" is a command for analysis and tracing hence
"systemd-analyze" should be the better home for it, thus allowing us to
make the overly large "systemctl" a bit smaller.
|
|
It's an analysis command and its format is explicitly not covered by any
stability guarantees, hence move away from systemctl and into
systemd-analyze, minimizing the already large interface of systemctl a
bit.
This patch also adds auto-paging to the various systemd-analyze commands
where that makes sense
|
|
message
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
$ systemctl --user status hoohoo
hoohoo.service
Loaded: loaded (/home/zbyszek/.config/systemd/user/hoohoo.service; static)
Active: inactive (dead)
start condition failed at Tue 2013-06-25 18:08:42 EDT; 1s ago
ConditionPathExists=/tmp/hoo was not met
Full information is exported over D-Bus:
[(condition, trigger, negate, param, state),...]
where state is one of "failed" (<0), "untested" (0), "OK" (>0).
I've decided to use 0 for "untested", because it might be useful to
differentiate different types of failure later on, without breaking
compatibility.
systemctl shows the failing condition, if there was a non-trigger
failing condition, or says "none of the trigger conditions were met",
because there're often many trigger conditions, and they must all
fail for the condition to fail, so printing them all would consume
a lot of space, and bring unnecessary attention to something that is
quite low-level.
|
|
|
|
This point was done in 77a9e8de6.
|
|
Two options are added: --show-cursor to print the cursor at the end,
and --after-cursor to resume logs on the next line after the previous one.
|
|
|
|
|
|
|
|
A few asserts are replaced with 'return -EINVAL'. I think that
assert should not be used to check argument in public functions.
Fields in struct sd_journal are rearranged to make it less
swiss-cheesy.
|
|
Hi,
I redid the boot ID look up to use enumerate_unique.
This is quite fast if the cache is warm but painfully slow if
it isn't. It has a slight chance of returning the wrong order if
realtime clock jumps around.
This one has to do n searches for every boot ID there is plus
a sort, so it depends heavily on cache hotness. This is in contrast
to the other way of look-up through filtering by a MESSAGE_ID,
which only needs about 1 seek + whatever amount of relative IDs
you want to walk.
I also have a linked-list + (in-place) mergesort version of this
patch, which has pretty much the same runtime. But since this one
is using libc sorting and armortized allocation, I prefer this
one.
To summarize: The MESSAGE_ID way is a *lot* faster but can be
incomplete due to rotation, while the enumerate+sort will find
every boot ID out there but will be painfully slow for large
journals and cold caches.
You choose :P
Jan
|
|
|
|
|
|
I think this is the most important of the capabilities bitmasks to log.
|
|
|
|
|
|
|
