| Age | Commit message (Collapse) | Author |
|---|
|
This patch implements support for the IFLA_BR_MCAST_SNOOPING attribute
it can change the multicast snooping value.
IGMP snooping monitors the Internet Group Management Protocol (IGMP)
traffic between hosts and multicast routers.
|
|
|
|
|
|
This patch add support to configure port
PortRange:
VXLAN bases source UDP port based on flow to help the
receiver to be able to load balance based on outer header flow.
DestinatinPort:
Allow configuring the default destination port on a per-device basis.
|
|
networkd: vxlan add option to set FDB entries
|
|
|
|
|
|
|
|
A variety of journal vacuuming improvements, plus an nspawn fix
|
|
|
|
.network files
In order to avoid confusion with the default files we ship, let's use a
low prefix number for all examples.
Fixes #1409.
|
|
|
|
This commit provides some basic bonding configuration examples for .netdev and .network files.
|
|
|
|
networkd: add support for Macvtap
|
|
Even when we use shortened, combined words, we still should uppercase
where a new word starts. I couldn't find a canonically capitalized
version of this term, hence I think we should follow our naming rules
here.
|
|
|
|
man: typo fixes
|
|
|
|
This should clear up some confusion in
https://github.com/systemd/systemd/issues/717.
This basically copies the description from systemd.unit to this
man page. Masking can happen also in /run, so strike the part
about /etc, and also add the magic work "mask".
|
|
Old name was slightly misleading, because this flag does not determine
whether DSCP is used overall, but only if it is copied to the
decapsulated packet. Rename to better reflect that.
"Copy" does not imply direction. This is on purpose, because we might
later on enhance the setting to allow/disallow copying in the other
direction, to the encapsulated packet. If that is implemented,
CopyDSCP could understand additional values. This is nicer than
having two separate settings and follows the example of DHCP=.
Also, we try to avoid abbreviations, but we allow acronyms
like MTU, in DiscoverPathMTU=.
This setting was recently added, so it's fine to rename it without
backwards compat.
|
|
http://marc.info/?l=linux-netdev&m=109507453227993&w=2
|
|
|
|
|
|
|
|
This did not really work out as we had hoped. Trying to do this upstream
introduced several problems that probably makes it better suited as a
downstream patch after all. At any rate, it is not releaseable in the
current state, so we at least need to revert this before the release.
* by adjusting the path to binaries, but not do the same thing to the
search path we end up with inconsistent man-pages. Adjusting the search
path too would be quite messy, and it is not at all obvious that this is
worth the effort, but at any rate it would have to be done before we
could ship this.
* this means that distributed man-pages does not make sense as they depend
on config options, and for better or worse we are still distributing
man pages, so that is something that definitely needs sorting out before
we could ship with this patch.
* we have long held that split-usr is only minimally supported in order
to boot, and something we hope will eventually go away. So before we start
adding even more magic/effort in order to make this work nicely, we should
probably question if it makes sense at all.
|
|
Replace some /usr/lib occurences in man/ with &rootprefix;/lib.
|
|
In particular, use /lib/systemd instead of /usr/lib/systemd in distributions
like Debian which still have not adopted a /usr merge setup.
Use XML entities from man/custom-entities.ent to replace configured paths while
doing XSLT processing of the original XML files. There was precedent of some
files (such as systemd.generator.xml) which were already using this approach.
This addresses most of the (manual) fixes from this patch:
http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/patches/Fix-paths-in-man-pages.patch?h=experimental-220
The idea of using generic XML entities was presented here:
http://lists.freedesktop.org/archives/systemd-devel/2015-May/032240.html
This patch solves almost all the issues, with the exception of:
- Path to /bin/mount and /bin/umount.
- Generic statements about preference of /lib over /etc.
These will be handled separately by follow up patches.
Tested:
- With default configure settings, ran "make install" to two separate
directories and compared the output to confirm they matched exactly.
- Used a set of configure flags including $CONFFLAGS from Debian:
http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/rules
Installed the tree and confirmed the paths use /lib/systemd instead of
/usr/lib/systemd and that no other unexpected differences exist.
- Confirmed that `make distcheck` still passes.
|
|
|
|
|
|
Rename bond confs and man as well.
[tomegun: dropped a stray comma]
|
|
This patch adds configurational support for bond option.
Test conf:
bond.netdev
---
[NetDev]
Name=bond1
Kind=bond
[Bond]
ArpAllTargets=all
PrimaryReselect=better
ArpIntervalSec=10s
ArpIpTargets= 192.168.8.102 192.168.8.101 192.168.8.102
---
$cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: load balancing (round-robin)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 10000
ARP IP target/s (n.n.n.n form): 192.168.8.100, 192.168.8.101, 192.168.8.102
|
|
Add UDPCheckSum option to enable transmitting UDP checksums when doing
VXLAN/IPv4. Add UDP6ZeroChecksumRx, and UDP6ZeroChecksumTx
options to enable sending zero checksums and receiving zero
checksums in VXLAN/IPv6
[tomegun: rebase manpage due to whitespace changes]
|
|
|
|
|
|
|
|
modes
Would be awesome to expand on this a lot, as there is currently no decent documentation for most of these things.
|
|
|
|
|
|
This patch introduces ipv6 gre and gretap.
test:
ip6gre.netdev:
[NetDev]
Name=ip6gretap
Kind=ip6gretap
[Tunnel]
Local=2a00:ffde:4567:edde::4987
Remote=2001:473:fece:cafe::5179
ip6gre.network:
[Match]
Name=eno16777736
[Network]
Tunnel=ip6gretap
ip link
6: ip6gre@eno16777736: <POINTOPOINT,NOARP> mtu 1448 qdisc noop state
DOWN mode DEFAULT group default
link/gre6 2a:00:ff:de:45:67:ed:de:00:00:00:00:00:00:49:87 peer
20:01:04:73:fe:ce:ca:fe:00:00:00:00:00:00:51:79
|
|
This patch enables networkd to create IP6 tunnels
example conf:
ipip6.netdev:
[NetDev]
Name=ipip6-tunnel
Kind=ip6tnl
[Tunnel]
Mode=ip4ipv6
Local=2a00:ffde:4567:edde::4987
Remote=2001:473:fece:cafe::5179
ipip6.network
[Match]
Name=wlan0
[Network]
Tunnel=ipip6-tunnel
23: ipip6-tunnel@wlan0: <POINTOPOINT,NOARP> mtu 1452 qdisc noop state
DOWN mode DEFAULT group default
link/tunnel6 2a00:ffde:4567:edde::4987 peer 2001:473:fece:cafe::5179
|
|
This patch introdeces gretap to networkd
|
|
|
|
|
|
V3: fix copy paste error
V4: Make manual and config more readable
Add vxlan paramertes to config.
|
|
The interface for creating tuntap devices should be ported to rtnl so it would support the same settings
as other kinds. In the meantime, the best one can do is to drop in a .link file to set the desired options.
|
|
The following bond options are supported by this patch.
MIIMonitorSec:
Specifies the frequency in milli-seconds that MII link
monitoring will occur.
UpDelaySec:
Specifies the delay time in milli-seconds to enable a link
after a link up status has been detected.
DownDelaySec:
Specifies the delay time in milli-seconds to disable a link
after a link failure has been detected.
changes:
1. Added gconf variables.
2. man page
conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
LacpduTransmitRate=fast
MIIMonitorSec=1s
UpDelaySec=2s
DownDelaySec=8s
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 1000
Up Delay (ms): 2000
Down Delay (ms): 8000
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: rephrased manpage, dropped bond_ prefix from variables]
|
|
LacpduTransmitRate
option specifies the rate in which link partner to transmit
LACPDU packets in 802.3ad mode. Possible values
slow : Request partner to transmit LACPDUs every 30 seconds
fast : Request partner to transmit LACPDUs every 1 second
The default is slow.
chages:
1. Added enum bond_lacp_rate_table
2. gperf LacpduTransmitRate
Test:
conf file:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
LacpduTransmitRate=fast
test:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: renamed from LacpduTransmitRate to LACPTransmitRate, manpage fixes and
dropped bond_ prefix from variables]
|
|
This patch adds support the transmit hash policy to use
for slave selection in balance-xor, 802.3ad, and tlb modes
layer2, layer3+4, layer2+3, encap3+4, encap3+4
Added:
1. BondXmitHashPolicy
2. conf param TransmitHashPolicy
Test conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
test output:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: slow
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: dropped bond_ prefix from new Bond variable, drop repeated man-page section]
|
|
We will happily use bridges/bonds as master devices, but we will not change their settings if they were created by
someone else.
|
