| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
Rename bond confs and man as well.
[tomegun: dropped a stray comma]
|
|
This patch adds configurational support for bond option.
Test conf:
bond.netdev
---
[NetDev]
Name=bond1
Kind=bond
[Bond]
ArpAllTargets=all
PrimaryReselect=better
ArpIntervalSec=10s
ArpIpTargets= 192.168.8.102 192.168.8.101 192.168.8.102
---
$cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: load balancing (round-robin)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 10000
ARP IP target/s (n.n.n.n form): 192.168.8.100, 192.168.8.101, 192.168.8.102
|
|
Add UDPCheckSum option to enable transmitting UDP checksums when doing
VXLAN/IPv4. Add UDP6ZeroChecksumRx, and UDP6ZeroChecksumTx
options to enable sending zero checksums and receiving zero
checksums in VXLAN/IPv6
[tomegun: rebase manpage due to whitespace changes]
|
|
|
|
|
|
|
|
modes
Would be awesome to expand on this a lot, as there is currently no decent documentation for most of these things.
|
|
|
|
|
|
This patch introduces ipv6 gre and gretap.
test:
ip6gre.netdev:
[NetDev]
Name=ip6gretap
Kind=ip6gretap
[Tunnel]
Local=2a00:ffde:4567:edde::4987
Remote=2001:473:fece:cafe::5179
ip6gre.network:
[Match]
Name=eno16777736
[Network]
Tunnel=ip6gretap
ip link
6: ip6gre@eno16777736: <POINTOPOINT,NOARP> mtu 1448 qdisc noop state
DOWN mode DEFAULT group default
link/gre6 2a:00:ff:de:45:67:ed:de:00:00:00:00:00:00:49:87 peer
20:01:04:73:fe:ce:ca:fe:00:00:00:00:00:00:51:79
|
|
This patch enables networkd to create IP6 tunnels
example conf:
ipip6.netdev:
[NetDev]
Name=ipip6-tunnel
Kind=ip6tnl
[Tunnel]
Mode=ip4ipv6
Local=2a00:ffde:4567:edde::4987
Remote=2001:473:fece:cafe::5179
ipip6.network
[Match]
Name=wlan0
[Network]
Tunnel=ipip6-tunnel
23: ipip6-tunnel@wlan0: <POINTOPOINT,NOARP> mtu 1452 qdisc noop state
DOWN mode DEFAULT group default
link/tunnel6 2a00:ffde:4567:edde::4987 peer 2001:473:fece:cafe::5179
|
|
This patch introdeces gretap to networkd
|
|
|
|
|
|
V3: fix copy paste error
V4: Make manual and config more readable
Add vxlan paramertes to config.
|
|
The interface for creating tuntap devices should be ported to rtnl so it would support the same settings
as other kinds. In the meantime, the best one can do is to drop in a .link file to set the desired options.
|
|
The following bond options are supported by this patch.
MIIMonitorSec:
Specifies the frequency in milli-seconds that MII link
monitoring will occur.
UpDelaySec:
Specifies the delay time in milli-seconds to enable a link
after a link up status has been detected.
DownDelaySec:
Specifies the delay time in milli-seconds to disable a link
after a link failure has been detected.
changes:
1. Added gconf variables.
2. man page
conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
LacpduTransmitRate=fast
MIIMonitorSec=1s
UpDelaySec=2s
DownDelaySec=8s
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 1000
Up Delay (ms): 2000
Down Delay (ms): 8000
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: rephrased manpage, dropped bond_ prefix from variables]
|
|
LacpduTransmitRate
option specifies the rate in which link partner to transmit
LACPDU packets in 802.3ad mode. Possible values
slow : Request partner to transmit LACPDUs every 30 seconds
fast : Request partner to transmit LACPDUs every 1 second
The default is slow.
chages:
1. Added enum bond_lacp_rate_table
2. gperf LacpduTransmitRate
Test:
conf file:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
LacpduTransmitRate=fast
test:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: renamed from LacpduTransmitRate to LACPTransmitRate, manpage fixes and
dropped bond_ prefix from variables]
|
|
This patch adds support the transmit hash policy to use
for slave selection in balance-xor, 802.3ad, and tlb modes
layer2, layer3+4, layer2+3, encap3+4, encap3+4
Added:
1. BondXmitHashPolicy
2. conf param TransmitHashPolicy
Test conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
test output:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: slow
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: dropped bond_ prefix from new Bond variable, drop repeated man-page section]
|
|
We will happily use bridges/bonds as master devices, but we will not change their settings if they were created by
someone else.
|
|
This patch adds supports networkd to configure bond mode
during creation via persistent conf. Mode can be configured
with conf param 'Mode'. A new section Bond is added to the
conf to support bond mode.
These modes can be configured now.
balance-rr
active-backup
balance-xor
broadcast
802.3ad
balance-tlb
balance-alb
Example conf file: test-bond.conf
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=balance-xor
Test case:
1. start networkd service:
12: bond1: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UNKNOWN mode DEFAULT group default
link/ether 22:89:6c:47:23:d2 brd ff:ff:ff:ff:ff:ff
2. find bond mode:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: load balancing (xor)
Transmit Hash Policy: layer2 (0)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
Changes:
1. Added file networkd-bond.c
2. Bond mode enum BondMode
3. conf section [Bond]
[tomegun: whitespace]
|
|
Reported by Moviuro <moviuro@gmail.com>
|
|
Susant says:
> ip tuntap turns this off by default.
Let's follow ip(8) here as that should be the least surprising.
|
|
|
|
This patch introduces TUN/TAP device creation support
to networkd.
Example conf to create a tap device:
file: tap.netdev
------------------
[NetDev]
Name=tap-test
Kind=tap
[Tap]
OneQueue=true
MultiQueue=true
PacketInfo=true
User=sus
Group=sus
------------------
Test:
1. output of ip link
tap-test: tap pi one_queue UNKNOWN_FLAGS:900 user 1000 group 1000
id:
uid=1000(sus) gid=10(wheel) groups=10(wheel),1000(sus)
context=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023
Modifications:
Added:
1. file networkd-tuntap.c
3. netdev kind NETDEV_KIND_TUN and NETDEV_KIND_TAP
2. Tun and Tap Sections and config params to parse
conf and gperf conf parameters
[tomegun: tweak the 'kind' checking for received ifindex]
|
|
|
|
Based on a diff by the mysterious 'poma'.
|
|
readability
|
|
|
|
|
|
|
