| Age | Commit message (Collapse) | Author |
|---|
|
This allows selecting the propagation level of emitted LLDP packets
(specifically: the destination MAC address of the packets). This is useful
because it allows generating LLDP packets that optionally cross certain types
of bridges.
See 802.11ab-2009, Table 7-1 for details.
|
|
|
|
networkd
|
|
|
|
Make the XML validate again.
|
|
It's only relevant to DHCP, and it should be where the DUID is configured too.
|
|
|
|
For similar reasons as the recent addition of a limit on sessions.
Note that we don't enforce a limit on inhibitors per-user currently, but
there's an implicit one, since each inhibitor takes up one fd, and fds are
limited via RLIMIT_NOFILE, and the limit on the number of processes per user.
|
|
We really should put limits on all resources we manage, hence add one to the
number of concurrent sessions, too. This was previously unbounded, hence set a
relatively high limit of 8K by default.
Note that most PAM setups will actually invoke pam_systemd prefixed with "-",
so that the return code of pam_systemd is ignored, and the login attempt
succeeds anyway. On systems like this the session will be created but is not
tracked by systemd.
|
|
Let's lower the default values a bit, and pick different defaults for
Accept=yes and Accept=no sockets.
Fixes: #3167
|
|
Rework DUID setting
|
|
make virtualization detection quieter, rework unit start limit logic, detect unit file drop-in changes correctly, fix autofs state propagation
|
|
Closes #2166.
We only allow 0, infinity and forever.
infinity and forever is same.
|
|
networkd: add support to set route table
|
|
networkd: add support to set route table
1. add support to configure the table id.
if id is less than 256 we can fit this in the header of route as
netlink property is a char. But in kernel this proepty is a
unsigned 32. Hence if greater that 256 add this as RTA_TABLE
attribute.
2. we are not setting the address family now. Now set this property.
|
|
This is essentially a revert of f38e0cce75ff2ffbd99f7e382ed39c160bb7d799 (which
removed the documentation of DUIDType on purpose). The description is heavily
updated for the new semantics.
This addresses #3127 § 4.
|
|
|
|
[/etc/systemd/system/test.socket:2] Unknown lvalue 'TriggerLimitIntervalBurst' in section 'Socket'
Follow-up for 8b26cdbd2a94
|
|
machined: make "clone" asynchronous, and support copy-based fall-back
|
|
Let's move the enforcement of the per-unit start limit from unit.c into the
type-specific files again. For unit types that know a concept of "result" codes
this allows us to hook up the start limit condition to it with an explicit
result code. Also, this makes sure that the state checks in clal like
service_start() may be done before the start limit is checked, as the start
limit really should be checked last, right before everything has been verified
to be in order.
The generic start limit logic is left in unit.c, but the invocation of it is
moved into the per-type files, in the various xyz_start() functions, so that
they may place the check at the right location.
Note that this change drops the enforcement entirely from device, slice, target
and scope units, since these unit types generally may not fail activation, or
may only be activated a single time. This is also documented now.
Note that restores the "start-limit-hit" result code that existed before
6bf0f408e4833152197fb38fb10a9989c89f3a59 already in the service code. However,
it's not introduced for all units that have a result code concept.
Fixes #3166.
|
|
|
|
Refuse aliases to non-aliasable units in more places
Fixes #2730.
|
|
Assorted fixes #3149 + one commit tacked on top
|
|
|
|
|
|
We generally follow the rule that for time settings we suffix the setting name
with "Sec" to indicate the default unit if none is specified. The only
exception was the rate limiting interval settings. Fix this, and keep the old
names for compatibility.
Do the same for journald's RateLimitInterval= setting
|
|
With #2564 unit start rate limiting was moved from after the condition checks
are to before they are made, in an attempt to fix #2467. This however resulted
in #2684. However, with a previous commit a concept of per socket unit trigger
rate limiting has been added, to fix #2467 more comprehensively, hence the
start limit can be moved after the condition checks again, thus fixing #2684.
Fixes: #2684
|
|
This adds two new settings TriggerLimitIntervalSec= and TriggerLimitBurst= that
define a rate limit for activation of socket units. When the limit is hit, the
socket is is put into a failure mode. This is an alternative fix for #2467,
since the original fix resulted in issue #2684.
In a later commit the StartLimitInterval=/StartLimitBurst= rate limiter will be
changed to be applied after any start conditions checks are made. This way,
there are two separate rate limiters enforced: one at triggering time, before
any jobs are queued with this patch, as well as the start limit that is moved
again to be run immediately before the unit is activated. Condition checks are
done in between the two, and thus no longer affect the start limit.
|
|
timers
Fixes #3122
|
|
Let's move DUID configuration into the [DHCP] section, since it only makes
sense in a DHCP context, and should be close to the configuration of
ClientIdentifier= and suchlike.
This really shouldn't be a section of its own, we don't have any for any of our
other per-protocol specific identifiers...
Follow-up for #2890 #2943
|
|
As suggested in:
https://github.com/systemd/systemd/pull/3124#discussion_r61068789
|
|
Add the boot parameter: systemd.default_timeout_start_sec to allow modification
of the default start job timeout at boot time.
|
|
|
|
This reverts commit 6e3930c40f3379b7123e505a71ba4cd6db6c372f.
Merge got squashed by mistake.
|
|
nspawn automatic user namespaces
|
|
* sd-journal: detect earlier if we try to read an object from an invalid offset
Specifically, detect early if we try to read from offset 0, i.e. are using
uninitialized offset data.
* journal: when dumping journal contents, react nicer to lines we can't read
If journal files are not cleanly closed it might happen that intermediaery
journal entries cannot be read. Handle this nicely, skip over the unreadable
entries, and log a debug message about it; after all we generally follow the
logic that we try to make the best of corrupted files.
* journal-file: always generate the same error when encountering corrupted files
Let's make sure EBADMSG is the one error we throw when we encounter corrupted
data, so that we can neatly test for it.
* journal-file: when iterating through a partly corruped journal file, treat error like EOF
When we linearly iterate through a corrupted journal file, and we encounter a
read error, don't consider this fatal, but merely as EOF condition (and log
about it).
* journal-file: make seeking in corrupted files work
Previously, when we used a bisection table for seeking through a corrupted
file, and the end of the bisection table was corrupted we'd most likely fail
the entire seek operation. Improve the situation: if we encounter invalid
entries in a bisection table, linearly go backwards until we find a working
entry again.
* man: elaborate on the automatic systemd-journald.socket service dependencies
Fixes: #1603
|
|
Fixes: #1603
|
|
Also, remove documentation for sd_journal_open_container() as we consider it
deprecated now.
|
|
I am pretty sure we shouldn't carry history sections in man pages, since it's
very hard to keep them correctly updated, the current ones are very
out-of-date, and they tend to make APIs appear unnecessarily complex.
|
|
With this change -U will turn on user namespacing only if the kernel actually
supports it and otherwise gracefully degrade to non-userns mode.
|
|
|
|
Closes #3096
|
|
|
|
This suppresses output of the hostname for messages from the local system.
Fixes: #2342
|
|
1970 UTC
aka "UNIX time".
Fixes: #2120
|
|
|
|
Nicer error message is symlinking chokes on an existing file
|
|
|
|
Fixes #1724.
|
|
When "preset" was executed for a unit without install info, we'd warn similarly
as for "enable" and "disable". But "preset" is usually called for all units,
because the preset files are provided by the distribution, and the units are under
control of individual programs, and it's reasonable to call "preset" for all units
rather then try to do it only for the ones that can be installed.
We also don't warn about missing info for "preset-all". Thus it seems reasonable
to silently ignore units w/o install info when presetting.
(In addition, when more than one unit was specified, we'd issue the warning
only if none of them had install info. But this is probably something to fix
for enable/disable too.)
|
