| Age | Commit message (Collapse) | Author |
|---|
|
BUILD_ID is a fairly generic field used to identify the system image
that was used to install the distribution.
|
|
The rules governing %s where just too complicated. First of
all, looking at $SHELL is dangerous. For systemd --system,
it usually wouldn't be set. But it could be set if the admin
first started a debug shell, let's say /sbin/sash, and then
launched systemd from it. This shouldn't influence how daemons
are started later on, so is better ignored. Similar reasoning
holds for session mode. Some shells set $SHELL, while other
set it only when it wasn't set previously (e.g. zsh). This
results in fragility that is better avoided by ignoring $SHELL
totally.
With $SHELL out of the way, simplify things by saying that
%s==/bin/sh for root, and the configured shell otherwise.
get_shell() is the only caller, so it can be inlined.
Fixes one issue seen with 'make check'.
|
|
|
|
|
|
user instance
|
|
which ones aren't
This also adds a short explanation paragraph for this.
|
|
mounts
This introduces remote-fs-setup.target independently of
remote-fs-pre.target. The former is only for pulling things in, the
latter only for ordering.
The new semantics:
remote-fs-setup.target: is pulled in automatically by all remote mounts.
Shall be used to pull in other units that want to run when at least one
remote mount is set up. Is not ordered against the actual mount units,
in order to allow activation of its dependencies even 'a posteriori',
i.e. when a mount is established outside of systemd and is only picked
up by it.
remote-fs-pre.target: needs to be pulled in automatically by the
implementing service, is otherwise not part of the initial transaction.
This is ordered before all remote mount units.
A service that wants to be pulled in and run before all remote mounts
should hence have:
a) WantedBy=remote-fs-setup.target -- so that it is pulled in
b) Wants=remote-fs-pre.target + Before=remote-fs-pre.target -- so that
it is ordered before the mount point, normally.
|
|
into for boot
|
|
Add option to force journal sync with fsync. Default timeout is 5min.
Interval configured via SyncIntervalSec option at journal.conf. Synced
journal files will be marked as OFFLINE.
Manual sync can be performed via sending SIGUSR1.
|
|
Previously, it would set all caps, but it should drop them all, anything
else makes little sense.
Also, document that this works as it does, and what to do in order to
assign all caps to the bounding set.
https://bugzilla.redhat.com/show_bug.cgi?id=914705
|
|
|
|
|
|
https://bugs.freedesktop.org/show_bug.cgi?id=38355
|
|
The ability to dump catalog entries in full and by id is added.
|
|
|
|
Seems natural to be able to specify relative directory,
e.g. with journalctl -D. And even if, this should be checked
in front-end code, not in the library.
|
|
|
|
Unlike IMPORT and PROGRAM, RUN is not executed inline, but after all the rules of the given event have been processed.
|
|
The properties will still be set in the udev database, but they will not be used
for setting the interface names. As for the other kernel commandline switches,
we allow it to be prefixed by 'rd.' to only apply in the initrd.
|
|
Moved from udev(7) to systemd-udevd.service(8), where the rest of the
documentation of the configuration of the daemon lives.
|
|
The new IMPORT{builtin} and RUN{builtin} were not documented. Also make it clear
that RUN= is really an alias for RUN{program}=.
|
|
|
|
All Execs within the service, will get mounted the same
/tmp and /var/tmp directories, if service is configured with
PrivateTmp=yes. Temporary directories are cleaned up by service
itself in addition to systemd-tmpfiles. Directory which is mounted
as inaccessible is created at runtime in /run/systemd.
|
|
|
|
I need this to test half-installed socket-activated python
script, which requires PYTHONPATH and LD_LIBRARY_PATH set.
I assume that other people might find it useful to.
-E VAR passes through VAR from the environment, while
-E VAR=value sets VAR=value.
systemd-activate -E PYTHONPATH=/var/tmp/inst1/usr/lib64/python3.3/site-packages -E LD_LIBRARY_PATH=/var/tmp/inst1/usr/lib -l 2000 python3 -c 'from systemd.daemon import listen_fds; print(listen_fds())'
|
|
Previously we were testing whether /sys/fs/cgroup/systemd/ was a mount
point. This might be problematic however, when the cgroup trees are bind
mounted into a container from the host (which should be absolutely
valid), which might create the impression that the container was running
systemd, but only the host actually is.
Replace this by a check for the existance of the directory
/run/systemd/system/, which should work unconditionally, since /run can
never be a bind mount but *must* be a tmpfs on systemd systems, which is
flushed at boots. This means that data in /run always reflects
information about the current boot, and only of the local container,
which makes it the perfect choice for a check like this.
(As side effect this is nice to Ubuntu people who now use logind with
the systemd cgroup hierarchy, where the old sd_booted() check misdetects
systemd, even though they still run legacy Upstart.)
|
|
|
|
First, rename root-fs.target to initrd-root-fs.target to clarify its usage.
Mount units with "x-initrd-rootfs.mount" are now ordered before
initrd-root-fs.target. As we sometimes construct /sysroot mounts in
/etc/fstab in the initrd, we want these to be mounted before the
initrd-root-fs.target is active.
initrd.target can be the default target in the initrd.
(normal startup)
:
:
v
basic.target
|
______________________/|
/ |
| sysroot.mount
| |
| v
| initrd-root-fs.target
| |
| v
| initrd-parse-etc.service
(custom initrd services) |
| v
| (sysroot-usr.mount and
| various mounts marked
| with fstab option
| x-initrd.mount)
| |
| v
| initrd-fs.target
| |
\______________________ |
\|
v
initrd.target
|
v
initrd-cleanup.service
isolates to
initrd-switch-root.target
|
v
______________________/|
/ |
| initrd-udevadm-cleanup-db.service
| |
(custom initrd services) |
| |
\______________________ |
\|
v
initrd-switch-root.target
|
v
initrd-switch-root.service
|
v
switch-root
|
|
journalctl -u unit is not very useful, because it doesn't show
systemd messages about starting, stopping, coredumps, etc,
like systemctl status unit does. Make it show the same
information using the same rules.
If somebody really want to see just messages from by the unit,
it is easy enough to use _SYSTEMD_UNIT=...
|
|
|
|
Instead of using local-fs*.target in the initrd, use root-fs.target for
sysroot.mount and initrd-fs.target for /sysroot/usr and friends.
Using local-fs.target would mean to carry over the activated
local-fs.target to the isolated initrd-switch-root.target and thus in
the real root. Having local-fs.target already active after
deserialization causes ordering problems with the real root services and
targets.
We better isolate to targets for initrd-switch-root.target, which are
only available in the initrd.
|
|
The documentation makes it sound like ExecStopPost is only run when
stopping the service with `systemctl stop foo.service`
However, that is not the case, as it also gets run when the service
unexpectedly exists, crashes, or gets SIGKILLed.
|
|
This should help readers of the man or HTML pages know if the documentation
is out of date. An alternative to use a date generated from 'git log' was
considered, but since we try to keep user visible documentation up to date,
showing the project version should be enough.
|
|
They contained the date, which creates a problem with multiarch
packages, since the generated file would be different each time.
|
|
Make sure the pager does not have to buffer an unbounded number of log
messages, by default.
|
|
Since the HTML files are in different directories during build
and on fd.o, links are broken in the build directory. This could
be fixed by moving stuff around, or by modifying the files during
upload, but I think that people do not usually create HTML files
for local browsing, and this is not necessary.
|
|
$ journalctl -be
is what you want :)
https://bugzilla.redhat.com/show_bug.cgi?id=867841
|
|
|
|
|
|
|
|
|
|
|
|
|
|
files
Previously all journal files were owned by "adm". In order to allow
specific users to read the journal files without granting it access to
the full "adm" powers, introduce a new specific group for this.
"systemd-journal" has to be created by the packaging scripts manually at
installation time. It's a good idea to assign a static UID/GID to this
group, since /var/log/journal might be shared across machines via NFS.
This commit also grants read access to the journal files by default to
members of the "wheel" and "adm" groups via file system ACLs, since
these "almost-root" groups should be able to see what's going on on the
system. These ACLs are created by "make install". Packagers probably
need to duplicate this logic in their postinst scripts.
This also adds documentation how to grant access to the journal to
additional users or groups via fs ACLs.
|
|
If coredump support is disabled via --disable-coredump, do not build and
install the systemd-coredumpctl binary and man page.
|
|
|
|
The condition was wrong: HAVE_PAM -> ENABLE_LOGIND.
|
|
Errors because of oom conditions or descriptor exhaustion should not
be ignored. We probably cannot recover from those conditions.
Current behaviour wrt. insufficient permissions is described in the
man page. It might make sense in case of user sessions, so I left
it as is.
|
|
Add --user-unit= to make it possible to query for user logs by the name
of the service.
|
|
|
