| Age | Commit message (Collapse) | Author |
|---|
|
|
|
When the CD tray door is locked and the hardware eject button is pressed, newer
kernels (2.6.38+) will send out a change event with a DISK_EJECT_REQUEST==1
property. Do not run cdrom_id and blkid in this case, as the media state and
contents does not change, and this only needlessly spins up the drive again
right before ejection.
|
|
If a USB device is marked as removable, it is often a SATA/PATA disk
in an enclosure (note that flash card readers and usb storage sticks
are always marked as removable). In this case, try running ata_id
(which sends ATA commands wrapped in SCSI ATA PASS THROUGH commands)
to get information about the disk. If this fails, just fall back to
running usb_id since it could be the device isn't an ATA device at
all or the device doesn't have a SAT layer.
This extra information is nice to have as it indicates if it is
suitable to send e.g. SMART commands to the disk, whether the disk
supports power management and so on. Additionally, the VPD and serial
number returned by ata_id is usually more accurate as it stems from
the disk itself instead of the enclosure.
Note that udisks has been doing this for a while
KERNEL=="sd*[!0-9]", ATTR{removable}=="0", ENV{ID_BUS}=="usb", ENV{DEVTYPE}=="disk", IMPORT{program}="udisks-probe-ata-smart $tempnode"
so this change shouldn't be too disruptive (udisks-probe-ata-smart
also sends ATA commands via the ATA PASS THROUGH command).
Signed-off-by: David Zeuthen <davidz@redhat.com>
|
|
|
|
Commit 5e9eb156c added new symlinks for multi-interface USB input devices.
However, we do not actually need the one for interface number "00", as we
already have the symlink without the interface number.
|
|
Create /dev/input/by-id symlinks containing the USB interface number so that
each interface in a multi-interface USB input device gets its own symlink.
Thanks to a7x <ubuntu-a7x@scientician.org>!
https://launchpad.net/bugs/626449
|
|
These patches enable usb autosuspend for the qemu emulated HID devices.
This reduces the cpu load for idle guests with a hid device attached
because the linux kernel will suspend the usb bus then and qemu can stop
running a 1000 Hz to emulate the (active) UHCI controller.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
|
|
The bsg devices node are created after the LUN, so we fail in the
hotplug case, but succeed at coldplug, and create inconsistent data
that way.
The bsg device event order will need to be sorted out, by changing the
kernel.
|
|
|
|
|
|
The major benefit here, is that we get the ATAPI device serial
number. With SCSI ID we didn't get this since it's not part of the
SCSI INQUIRY command. Specifically this means that we get symlinks to
empty optical drives, e.g.
/dev/disk/by-id/ata-VBOX_CD-ROM_VB2-01700376
which we didn't get earlier. So this is a major win.
Also make ata_id work on CD-ROM devices when using /dev/bsg nodes so
this works on both the scsi_device as well as the block device. We do
this, basically, by issuing the ATA IDENTIFY PACKET DEVICE command
instead of the ATA IDENTIFY command. We also use 16-byte pass-through
ATA passthrough instead of 12-byte passthrough to avoid clashing with
the MMC BLANK command.
This means that we get this output
# udevadm info -q all -p /sys/devices/pci0000:00/0000:00:01.1/host3/target3:0:0/3:0:0:0
P: /devices/pci0000:00/0000:00:01.1/host3/target3:0:0/3:0:0:0
E: UDEV_LOG=3
E: DEVPATH=/devices/pci0000:00/0000:00:01.1/host3/target3:0:0/3:0:0:0
E: DEVTYPE=scsi_device
E: DRIVER=sr
E: MODALIAS=scsi:t-0x05
E: SUBSYSTEM=scsi
E: ID_ATA=1
E: ID_TYPE=cd
E: ID_BUS=ata
E: ID_MODEL=VBOX_CD-ROM
E: ID_MODEL_ENC=VBOX\x20CD-ROM\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20\x 20\x20\x20\x20\x20\x20\x20
E: ID_REVISION=1.0
E: ID_SERIAL=VBOX_CD-ROM_VB2-01700376
E: ID_SERIAL_SHORT=VB2-01700376
instead of just
# udevadm info -q all -p /sys/devices/pci0000:00/0000:00:01.1/host3/target3:0:0/3:0:0:0
P: /devices/pci0000:00/0000:00:01.1/host3/target3:0:0/3:0:0:0
E: UDEV_LOG=3
E: DEVPATH=/devices/pci0000:00/0000:00:01.1/host3/target3:0:0/3:0:0:0
E: DEVTYPE=scsi_device
E: DRIVER=sr
E: MODALIAS=scsi:t-0x05
E: SUBSYSTEM=scsi
E: ID_SCSI=1
E: ID_VENDOR=VBOX
E: ID_VENDOR_ENC=VBOX\x20\x20\x20\x20
E: ID_MODEL=CD-ROM
E: ID_MODEL_ENC=CD-ROM\x20\x20\x20\x20\x20\x20\x20\x20\x20\x20
E: ID_REVISION=1.0
E: ID_TYPE=cd
Signed-off-by: David Zeuthen <davidz@redhat.com>
|
|
In a multi-initiator setup, the HBA may very well export a SCSI device
for a device that another initiator has already logged into. But since
another initiator has already logged in, the kernel will not create a
block device.
Note that this is also the case for some RAID HBAs - for example, the
LSI 1068 series cards will export a SCSI device for a disk that is in
use by the HBAs RAID engine (no block device will be created here).
Running scsi_id and ata_id on the actual SCSI device means that we can
inquire the capabilities of the device. For example, we can check
whether ID_ATA_FEATURE_SET_SMART and ID_ATA_FEATURE_SET_SMART_ENABLED
is set and, if so, periodically poll the SMART status of the
disk. Even when other initiators has claimed the disk and if the disk
is in use by the RAID engine of the HBA.
Note that we run scsi_id and ata_id on /dev/bsg/* nodes - this is safe
to do because the scsi core guarantees that the bsg device has been
created before the actual add uevent for the scsi_device is emitted.
Since the block device is a direct child of the scsi_device we can
avoid running scsi_id and ata_id again by simply importing the
resulting ID_* properties from the parent.
Signed-off-by: David Zeuthen <davidz@redhat.com>
|
|
|
|
|
|
1. IIDC cameras from Point Grey use the vendor OUI as Specifier_ID
instead of the 1394 TA's OUI but are otherwise fully compliant to the
IIDC spec. Their device files should be accessible like those of any
other IIDC cameras.
2. Originally, the Software_Version of devices that implement FCP
(IEC 61883-1 Function Control Protocol) was meant to be a bitmap of all
command sets that an FCP capable unit supports. Bitmap flags are
defined for AV/C, CAL, EHS, HAVi, and vendor unique command sets.
Software_Version was revised to be a simple identifier instead, and
devices that support several command sets were meant to instantiate one
unit directory for each command set. Still, some devices with the flags
for AV/C and vendor unique command sets combined were released (but
apparently no devices with any other flag combinations). These rare but
existing AV/C + vendor unique devices need to be accessible just like
plain AV/C devices.
Side notes:
- Many AV/C devices make use of the Vendor Dependent AV/C command, but
this is unrelated to vendor unique FCP command sets.
- Here are all standardized FireWire protocol identifiers that I know
of, listed as Specifier_ID:Software_Version | specifier | protocol.
0x00005e:0x000001 | IANA | IPv4 over 1394 (RFC 2734)
0x00005e:0x000002 | IANA | IPv6 over 1394 (RFC 3146)
0x00609e:0x010483 | INCITS | SBP-2 (or SCSI command sets over SBP-3)
0x00609e:0x0105bb | INCITS | AV/C over SBP-3
0x00a02d:0x010001 | 1394 TA | AV/C (over FCP)
0x00a02d:0x010002 | 1394 TA | CAL
0x00a02d:0x010004 | 1394 TA | EHS
0x00a02d:0x010008 | 1394 TA | HAVi
0x00a02d:0x014000 | 1394 TA | Vendor Unique
0x00a02d:0x014001 | 1394 TA | Vendor Unique and AV/C (over FCP)
0x00a02d:0x000100 | 1394 TA | IIDC 1.04
0x00a02d:0x000101 | 1394 TA | IIDC 1.20
0x00a02d:0x000102 | 1394 TA | IIDC 1.30
0x00a02d:0x0A6BE2 | 1394 TA | DPP 1.0
0x00a02d:0x4B661F | 1394 TA | IICP 1.0
For now we are only interested in udev rules for AV/C and IIDC.
Reported-by: Damien Douxchamps <ddsf@douxchamps.net> (Point Grey IIDC ID)
Reported-by: Clemens Ladisch <clemens@ladisch.de> (AV/C + vendor unique ID)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
|
|
|
|
|
|
Using virtio-blk serial attributes add rules to extract drive serial numbers and
generate by-id links for the block device and partitions.
With these rules added, we now see the following symlinks in disk/by-id
% ls -al /dev/disk/by-id | grep vdb
lrwxrwxrwx. 1 root root 9 Jun 1 22:09 virtio-QM00001 -> ../../vda
lrwxrwxrwx. 1 root root 10 Jun 1 22:09 virtio-QM00001-part1 -> ../../vda1
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
|
|
|
|
Commit f61e72d89 failed to match for the case where an USB printer has multiple
interfaces, such as
ID_USB_INTERFACES=:ffffff:070102:
Thanks to Pablo Mazzini for spotting this!
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
We should not access non-data optical media, ans skip things
like blkid. It will cause errors for some drives.
https://bugzilla.kernel.org/show_bug.cgi?id=15757
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fix provided by Harald Hoyer.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
|
|
|
|
Newer udev versions don't understand $ATTR.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Martin Pitt <martin.pitt@ubuntu.com>
|
|
virtio ports spawned by the virtio_console.c driver can have 'names'
assigned to them by hosts. The ports are distinguishable using these
names. Make a rule to create a symlink to the chardev associated for a
port with a name.
The symlink created is:
/dev/virtio-ports/org.libvirt.console0 -> /dev/vport0p0
if the first port for the first device was given a name of
'org.libvirt.console0'.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
|
|
|
|
|
|
|
|
Some SCSI devices use the same WWN and have a WWN extension that we
need to take into account when creating the /dev/disk/by-id/wwn
symlinks. Thus, introduce ID_WWN_WITH_EXTENSION. This property will
contain either the WWN (if no extension is present) or the WWN with
the vendor extension appended.
Example:
# /lib/udev/ata_id/ata_id --export /dev/sda |grep WWN
ID_WWN=0x5001517387d61905
ID_WWN_WITH_EXTENSION=0x5001517387d61905
# /lib/udev/scsi_id --whitelisted --export -d /dev/sdb |grep WWN
ID_WWN=0x600508b400105df7
ID_WWN_VENDOR_EXTENSION=0x0000e00000d80000
ID_WWN_WITH_EXTENSION=0x600508b400105df70000e00000d80000
# /lib/udev/scsi_id --whitelisted --export -d /dev/sdc |grep WWN
ID_WWN=0x600508b400105df7
ID_WWN_VENDOR_EXTENSION=0x0000e00000db0000
ID_WWN_WITH_EXTENSION=0x600508b400105df70000e00000db0000
Signed-off-by: David Zeuthen <davidz@redhat.com>
|
|
The ID_CLASS property on input devices has been replaced by the more accurate
set of flags ID_INPUT_{KEYBOARD,KEYS,MOUSE,TOUCHPAD,TABLET,JOYSTICK}.
Rewrite 60-persistent-input.rules to use the new properties now and not export
ID_CLASS any more, since it is not used by anything else any more.
Add note about migration to NEWS, in case this is being used in custom rules.
|
|
input_id probes input/event devices for their class (keyboard, keys, mouse,
touchpad, tablet, joystick). This is based on the corresponding hal code in
hald/linux/device.c, input_test_{abs,rel,...}.
This should provide enough functionality to get hal-less X.org working (which
in particular needs to know exactly which devices are touchpads).
Replace the brittle hacks in 60-persistent-input.rules with checking for the
new ID_INPUT_* flags. This keeps the old ID_CLASS properties for now (but they
are to be removed later on).
Note: The current code has several hacks still, which are to be replaced with
proper libudev calls later on.
|
|
# ls -l /dev/disk/by-id/wwn-0x500
wwn-0x500000e01b83f360 wwn-0x50014ee25578924f-part1
wwn-0x500000e01b83f440 wwn-0x50014ee25578924f-part2
wwn-0x500000e01b83f520 wwn-0x50014ee2aabdc41b
wwn-0x500000e01b843d90 wwn-0x50014ee2aabdc41b-part1
wwn-0x5000c50016359fd1 wwn-0x50014ee2aabdc41b-part2
wwn-0x50014ee0016eb4f5 wwn-0x5001517958cabd77
wwn-0x50014ee0016eb572 wwn-0x5001517958cabd77-part1
wwn-0x50014ee055d524e2 wwn-0x5001517958cabd77-part2
wwn-0x50014ee055d524e2-part1 wwn-0x5001517958d6a74e
wwn-0x50014ee055d524e2-part2 wwn-0x5001517958d6a74e-part1
wwn-0x50014ee1003d9c50 wwn-0x5001517958d6a74e-part2
wwn-0x50014ee1003d9c50-part1 wwn-0x50024e9200c0c693
wwn-0x50014ee1003d9c50-part2 wwn-0x50024e9200c0c694
wwn-0x50014ee1aac30d4e wwn-0x50024e9200c0c6ae
wwn-0x50014ee1aac30d4e-part1 wwn-0x50024e9200c0c6af
wwn-0x50014ee1aac30d4e-part2 wwn-0x50024e9200c0c6b0
wwn-0x50014ee25578924f wwn-0x50024e9200c0c6b1
Signed-off-by: David Zeuthen <davidz@redhat.com>
|
|
Now that both ata_id and scsi_id exports the World Wide Name in the
ID_WWN property, use this to create persistent symlinks. Example
/dev/disk/by-id/wwn-0x500000e01b83f360 -> ../../sdn
/dev/disk/by-id/wwn-0x500000e01b83f440 -> ../../sdm
Signed-off-by: David Zeuthen <davidz@redhat.com>
|
|
The kernel IDE drivers get deprecated now:
http://article.gmane.org/gmane.linux.ide/43151
Almost everybody has switched over to libata devices long ago.
Recent services do not work with the now deprecated IDE drivers
at all and require libata drivers and SCSI infrastructure.
Systems who care about the old stuff need to add the rules to the
compat rules.
|
