| Age | Commit message (Collapse) | Author |
|---|
|
We should not fall back to dbus-1 and connect to the proxy when kdbus
returns an error that indicates that kdbus is running but just does not
accept new connections because of quota limits or something similar.
Using is_kdbus_available() in libsystemd/ requires it to move from
shared/ to libsystemd/.
Based on a patch from David Herrmann:
https://github.com/systemd/systemd/pull/886
|
|
- Add smack xattr lookup table
- Unify all of mac_smack_apply_xxx{_fd}() to mac_smack_apply() and
mac_smack_apply_fd().
- Add smack xattr read apis similar with apply apis as
mac_smack_read{_fd}().
|
|
These units' message format strings are identical to the generic
strings. Since we can always rely on the fallback, these are now
redundant.
|
|
bind() fails if it is called before setting SO_REUSEPORT and another
process is already binded to the same addess.
A new reuse_port option has been introduced to socket_address_listen()
to set the option as part of socket initialization.
|
|
mask/handlers
Also, when the child is potentially long-running make sure to set a
death signal.
Also, ignore the result of the reset operations explicitly by casting
them to (void).
|
|
|
|
No functional changes.
|
|
|
|
It's primarily just a property of the Manager object after all, and we
try to refer to PID 1 as "manager" instead of "systemd", hence let's to
stick to this here too.
|
|
This changes log_unit_info() (and friends) to take a real Unit* object
insted of just a unit name as parameter. The call will now prefix all
logged messages with the unit name, thus allowing the unit name to be
dropped from the various passed romat strings, simplifying invocations
drastically, and unifying log output across messages. Also, UNIT= vs.
USER_UNIT= is now derived from the Manager object attached to the Unit
object, instead of getpid(). This has the benefit of correcting the
field for --test runs.
Also contains a couple of other logging improvements:
- Drops a couple of strerror() invocations in favour of using %m.
- Not only .mount units now warn if a symlinks exist for the mount
point already, .automount units do that too, now.
- A few invocations of log_struct() that didn't actually pass any
additional structured data have been replaced by simpler invocations
of log_unit_info() and friends.
- For structured data a new LOG_UNIT_MESSAGE() macro has been added,
that works like LOG_MESSAGE() but prefixes the message with the unit
name. Similar, there's now LOG_LINK_MESSAGE() and
LOG_NETDEV_MESSAGE().
- For structured data new LOG_UNIT_ID(), LOG_LINK_INTERFACE(),
LOG_NETDEV_INTERFACE() macros have been added that generate the
necessary per object fields. The old log_unit_struct() call has been
removed in favour of these new macros used in raw log_struct()
invocations. In addition to removing one more function call this
allows generated structured log messages that contain two object
fields, as necessary for example for network interfaces that are
joined into another network interface, and whose messages shall be
indexed by both.
- The LOG_ERRNO() macro has been removed, in favour of
log_struct_errno(). The latter has the benefit of ensuring that %m in
format strings is properly resolved to the specified error number.
- A number of logging messages have been converted to use
log_unit_info() instead of log_info()
- The client code in sysv-generator no longer #includes core code from
src/core/.
- log_unit_full_errno() has been removed, log_unit_full() instead takes
an errno now, too.
- log_unit_info(), log_link_info(), log_netdev_info() and friends, now
avoid double evaluation of their parameters
|
|
Otherwise it might be passed in as 0, which is a valid fd, but usually
does not refer to a real endpoint.
|
|
A variety of changes:
- Make sure all our calls distuingish OOM from other errors if OOM is
not the only error possible.
- Be much stricter when parsing escaped paths, do not accept trailing or
leading escaped slashes.
- Change unit validation to take a bit mask for allowing plain names,
instance names or template names or an combination thereof.
- Refuse manipulating invalid unit name
|
|
These looked like a mass-replace gone slightly wrong – two statements
with no { }'s, and no error checking.
|
|
|
|
This reverts commit 6e392c9c45643d106673c6643ac8bf4e65da13c1.
We really shouldn't invent external state keeping hashmaps, if we can
keep this state in the units themselves.
|
|
|
|
|
|
Because the order of coldplugging is not defined, we can reference a
not-yet-coldplugged unit and read its state while it has not yet been
set to a meaningful value.
This way, already active units may get started again.
We fix this by deferring such actions until all units have been at
least somehow coldplugged.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=88401
|
|
This adds support for showing the accumulated consumed CPU time per-unit
in the "systemctl status" output. The property is also readable via the
bus.
|
|
This patch removes includes that are not used. The removals were found with
include-what-you-use which checks if any of the symbols from a header is
in use.
|
|
When dbus.socket is updated like this:
-ListenStream=/var/run/dbus/system_bus_socket
+ListenStream=/run/dbus/system_bus_socket
... and daemon-reload is performed, bad things happen.
During deserialization systemd does not recognize that the two paths
refer to the same named socket and replaces the socket file with a new
one. As a result, applications hang when they try talking to dbus.
Fix this by finding a match not only when the path names are equal, but
also when they point to the same inode.
In socket_address_equal() it is necessary to move the address size
comparison into the abstract sockets branch. For path name sockets the
comparison must not be done and for other families it is redundant
(their sizes are constant and checked by socket_address_verify()).
FIFOs and special files can also have multiple pathnames, so compare the
inodes for them as well. Note that previously the pathname checks used
streq_ptr(), but the paths cannot be NULL.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1186018
|
|
If a service has an ExecStop= program that uses the socket the service was
activated by to tell it to terminate, then that should not be used as
trigger to start the service again.
http://lists.freedesktop.org/archives/systemd-devel/2015-February/028058.html
|
|
After all it is now much more like strjoin() than strappend(). At the
same time, add support for NULL sentinels, even if they are normally not
necessary.
|
|
changing unit state
Unit _start() and _stop() implementations can fail with -EAGAIN to delay
execution temporarily. Thus, we should not output status messages before
invoking these calls, but after, and only when we know that the
invocation actually made a change.
|
|
|
|
|
|
Using:
find . -name '*.[ch]' | xargs sed -r -i -e \
's/log_unit_(debug|info|notice|warning|error|emergency)\(([^"]+), "(.*)%s"(.*), strerror\(-([a-zA-Z_]+)\)\);/log_unit_\1_errno(\2, \5, "\3%m"\4);/'
|
|
It corrrectly handles both positive and negative errno values.
|
|
As a followup to 086891e5c1 "log: add an "error" parameter to all
low-level logging calls and intrdouce log_error_errno() as log calls
that take error numbers", use sed to convert the simple cases to use
the new macros:
find . -name '*.[ch]' | xargs sed -r -i -e \
's/log_(debug|info|notice|warning|error|emergency)\("(.*)%s"(.*), strerror\(-([a-zA-Z_]+)\)\);/log_\1_errno(-\4, "\2%m"\3);/'
Multi-line log_*() invocations are not covered.
And we also should add log_unit_*_errno().
|
|
- Rename log_meta() → log_internal(), to follow naming scheme of most
other log functions that are usually invoked through macros, but never
directly.
- Rename log_info_object() to log_object_info(), simply because the
object should be before any other parameters, to follow OO-style
programming style.
|
|
subhierarchies
For priviliged units this resource control property ensures that the
processes have all controllers systemd manages enabled.
For unpriviliged services (those with User= set) this ensures that
access rights to the service cgroup is granted to the user in question,
to create further subgroups. Note that this only applies to the
name=systemd hierarchy though, as access to other controllers is not
safe for unpriviliged processes.
Delegate=yes should be set for container scopes where a systemd instance
inside the container shall manage the hierarchies below its own cgroup
and have access to all controllers.
Delegate=yes should also be set for user@.service, so that systemd
--user can run, controlling its own cgroup tree.
This commit changes machined, systemd-nspawn@.service and user@.service
to set this boolean, in order to ensure that container management will
just work, and the user systemd instance can run fine.
|
|
if sigabrt doesn't do the job, follow regular shutdown
routine, sigterm > sigkill.
|
|
|
|
|
|
|
|
APIs that query and return something cannot silently fail, they must
either return something useful, or an error. Fix that.
Also, properly rollback socket unit fd creation when something goes
wrong with the security framework.
|
|
a) always return negative errno error codes
b) always become a noop if smack is off
c) always take a NULL label as a request to remove it
|
|
and all that reset it to defaults mac_{selinux|smack}_fix()
Let's clean up the naming schemes a bit and use the same one for SMACK
and for SELINUX.
|
|
|
|
This makes possible to spawn service instances triggered by socket with
MLS/MCS SELinux labels which are created based on information provided by
connected peer.
Implementation of label_get_child_mls_label derived from xinetd.
Reviewed-by: Paul Moore <pmoore@redhat.com>
|
|
This way, the list of arguments to that function gets more comprehensive,
and we can get around passing lots of NULL and 0 arguments from socket.c,
swap.c and mount.c.
It also allows for splitting up the code in exec_spawn().
While at it, make ExecContext const in execute.c.
|
|
|
|
This is what we have done so far for all other time values, and hence we
should do this here. This indicates the default unit of time values
specified here, if they don't contain a unit.
|
|
This reverts commit cf8bd44339b00330fdbc91041d6731ba8aba9fec.
Needs more discussion on the mailing list.
|
|
This makes possible to spawn service instances triggered by socket with
MLS/MCS SELinux labels which are created based on information provided by
connected peer.
Implementation of label_get_child_label derived from xinetd.
Reviewed-by: Paul Moore <pmoore@redhat.com>
|
|
TCP_DEFER_ACCEPT Allow a listener to be awakened only when data
arrives on the socket. If TCP_DEFER_ACCEPT set on a server-side
listening socket, the TCP/IP stack will not to wait for the final
ACK packet and not to initiate the process until the first packet
of real data has arrived. After sending the SYN/ACK, the server will
then wait for a data packet from a client. Now, only three packets
will be sent over the network, and the connection establishment delay
will be significantly reduced.
|
|
The tcp keep alive variables now can be configured via conf
parameter. Follwing variables are now supported by this patch.
tcp_keepalive_intvl: The number of seconds between TCP keep-alive probes
tcp_keepalive_probes: The maximum number of TCP keep-alive probes to
send before giving up and killing the connection if no response is
obtained from the other end.
tcp_keepalive_time: The number of seconds a connection needs to be
idle before TCP begins sending out keep-alive probes.
|
|
This reverts commit 9528592ff8d7ff361da430285deba8196e8984d5.
Apparently TFO is actually the default at least for the server side now.
Also the setsockopt doesn't actually take a bool, but a qlen integer.
|
|
TCP Fast Open (TFO) speeds up the opening of successiveTCP)
connections between two endpoints.It works by using a TFO cookie
in the initial SYN packet to authenticate a previously connected
client. It starts sending data to the client before the receipt
of the final ACK packet of the three way handshake is received,
skipping a round trip and lowering the latency in the start of
transmission of data.
|
|
This patch adds support for TCP TCP_NODELAY socket option. This can be
configured via NoDelay conf parameter. TCP Nagle's algorithm works by
combining a number of small outgoing messages, and sending them all at
once. This controls the TCP_NODELAY socket option.
|
