Age | Commit message (Collapse) | Author |
|
Closes #919.
|
|
Fix machinectl login with containers in user namespaces (v2)
|
|
To be able to use `systemd-run` or `machinectl login` on a container
that is in a private user namespace, the sub-process must have entered
the user namespace before connecting to the container's D-Bus, otherwise
the UID and GID in the peer credentials are garbage.
So we extend namespace_open and namespace_enter to support UID namespaces,
and we enter the UID namespace in bus_container_connect_{socket,kernel}.
namespace_open will degrade to a no-op if user namespaces are not enabled
in the kernel.
Special handling is required for the setns call in namespace_enter with
a user namespace, since transitioning to your own namespace is forbidden,
as it would result in re-entering your user namespace as root.
Arguably it may be valid to check this at the call site, rather than
inside namespace_enter, but it is less code to do it inside, and if the
intention of calling namespace_enter is to *be* in the target namespace,
rather than to transition to the target namespace, it is a reasonable
approach.
The check for whether the user namespace is the same must happen before
entering namespaces, as we may not be able to access /proc during the
intermediate transition stage.
We can't instead attempt to enter the user namespace and then ignore
the failure from it being the same namespace, since the error code is
not distinct, and we can't compare namespaces while mid-transition.
|
|
The following functions return immediately if a null pointer was passed.
* calendar_spec_free
* link_address_free
* manager_free
* sd_bus_unref
* sd_journal_close
* udev_monitor_unref
* udev_unref
It is therefore not needed that a function caller repeats a corresponding check.
This issue was fixed by using the software Coccinelle 1.0.1.
|
|
Allow arbitrary file paths to be passed to nspawn (v3)
|
|
We should not fall back to dbus-1 and connect to the proxy when kdbus
returns an error that indicates that kdbus is running but just does not
accept new connections because of quota limits or something similar.
Using is_kdbus_available() in libsystemd/ requires it to move from
shared/ to libsystemd/.
Based on a patch from David Herrmann:
https://github.com/systemd/systemd/pull/886
|
|
This adds an EXTRACT_QUOTES option to allow the previous behaviour, of
not interpreting any character inside ' or " quotes as separators.
|
|
It now takes a separators argument, which defaults to WHITESPACE if NULL
is passed.
|
|
This is so that, when called in a loop, unquote_first_word can
distinguish between reaching the end of a string because it has consumed
all the input before the end, and consuming all the input.
This is important because we later add a flag that allows
char *in = "";
char *out;
unquote_first_word(&in, &out, flags);
To put "" in out, and set in = NULL, so the trailing empty string of the
input can be consumed, and mark that the input has been consumed.
|
|
Signed-off-by: Jan Pokorný <jpokorny@redhat.com>
|
|
https://bugzilla.redhat.com/show_bug.cgi?id=1251334
|
|
execute: don't fail if we create the runtime directory from two proce…
|
|
simultaneously
If a service has both ExecStart= and ExecStartPost= set with
Type=simple, then it might happen that we have two children create the
runtime directory of a service (as configured with RuntimeDirectory=) at
the same time. Previously we did this with mkdir_safe() which will
create the dir only if it is missing, but if it already exists will at
least verify the access mode and ownership to match the right values.
This is problematic in this case, since it creates and then adjusts the
settings, thus it might happen that one child creates the directory with
root owner, another one then verifies it, and only afterwards the
directory ownership is fixed by the original child, while the second
child already failed.
With this change we'll now always adjust the access mode, so that we
know that it is right. In the worst case this means we adjust the
mode/ownership even though its unnecessary, but this should have no
negative effect.
https://bugzilla.redhat.com/show_bug.cgi?id=1226509
|
|
The ->done callback in the unit's vtable might call into
unit_unwatch_bus_name() and corrupt memory by that.
Move the call down, and clean up the bus slot in case it hasn't been done
yet.
|
|
Currently, PID1 installs an unfiltered NameOwnerChanged signal match, and
dispatches the signals itself. This does not scale, as right now, PID1
wakes up every time a bus client connects.
To fix this, install individual matches once they are requested by
unit_watch_bus_name(), and remove the watches again through their slot in
unit_unwatch_bus_name().
If the bus is not available during unit_watch_bus_name(), just store
name in the 'watch_bus' hashmap, and let bus_setup_api() do the installing
later.
|
|
|
|
When command path has access label and no SmackProcessLabel= is not
set, default process label will be set. But if the default process
label has no rule for the access label of the command path then smack
access error will be occurred.
So, if the command path has execute label then the child have to set
its label to the same of execute label of command path instead of
default process label.
|
|
- Add smack xattr lookup table
- Unify all of mac_smack_apply_xxx{_fd}() to mac_smack_apply() and
mac_smack_apply_fd().
- Add smack xattr read apis similar with apply apis as
mac_smack_read{_fd}().
|
|
Pretty trivial helper which wraps free() but returns NULL, so we can
simplify this:
free(foobar);
foobar = NULL;
to this:
foobar = mfree(foobar);
|
|
Some places invoked fflush() directly with their own manual error
checking, let's unify all that by using fflush_and_check().
This also unifies the general error paths of fflush()+rename() file
writers.
|
|
It seems that systemd still uses legacy -n option. The option has been
originally designed to avoid write to /etc/mtab during boot when root
FS is not ready or read-only.
This is not necessary for long time, because /etc/mtab is not a real
file (it's symlink) and write to the file is impossible. All utils
should be able to detect the symlink and ignore mtab. This concept is
supported for very long time before systemd.
The userspase mount options are currently maintained by libmount
(mount(8) and mount.nfs) in /run/mount) which is tmpfs initialized
during early boot.
|
|
selinux: fix missing SELinux unit access check
|
|
The expire timeout must be started/stopped if the corresponding mount unit
changes its state, e.g. it is started via local-fs.target or stopped by a
manual umount.
|
|
Return the token immediately instead. Otherwise the token is never returned
to the kernel, because the umount job is a noop and will not trigger a
state change.
|
|
The timer value for automount unit specified with TimeoutIdleSec= is rounded
up to one second if that directive is set to 0.
Fix this by bailing early in automount_enter_runnning() in case no timeout is
requested.
|
|
automount: lower the idle polling frequency a bit
|
|
This should make issues like #609 easier to debug.
|
|
The autofs kernel idle logic requires us to poll the kernel for
idleness. This is of course suboptimal, but cannot be fixed without
kernel change.
Currently the polling frequency is set to 1/10 of the idle timeout. This
is quite high, as seen in #571. Let's lower this to 1/3.
|
|
We do not print all non-OK job completion status messages to the console
in red, because not all of them are plain errors. We do however log the
same messages as LOG_ERR.
Differentiate the log levels by deducing them from the job result in a
way that more or less matches the color of the console message.
|
|
Joins three log_struct() calls into one.
|
|
JOB_RESTART and failed JOB_VERIFY_ACTIVE completions were printed to
console but not to the log.
|
|
It is misleading to see "Started foo." in the log when the unit's
condition was false.
|
|
These units' message format strings are identical to the generic
strings. Since we can always rely on the fallback, these are now
redundant.
|
|
This is similar to "core: always try harder to get unit status
message format string", but for job completion status messages.
It makes generic status messages applicable for printing to the console.
And it rewrites the functions in a more table-based style.
|
|
unit_get_status_message_format() is used only with one of JOB_START,
JOB_STOP, JOB_RELOAD, all of which have fallback message strings
defined, so the function may never return NULL.
|
|
The starting/stopping messages are printed to the console only if the
corresponding format string is defined in the unit's vtable. To avoid
excessive messages on the console, the unit types whose start/stop
jobs are instantaneous had the format strings intentionally undefined.
When logging the same event to the journal, a fallback to generic
Starting/Stopping/Reloading messages is used.
The problem of excessive console messages with instantaneous jobs
is already resolved in a nicer way ("core: fix confusing logging of
instantaneous jobs"), so there's no longer a need to have two ways of
getting the format strings. Let's fold them into one function with
the fallback to generic message strings.
|
|
Return 1 from *_reload() methods to signify "we did something", just
like in *_start(). This causes "Reloading foo..." messages to be logged.
"Reloaded foo." messages are already logged.
|
|
For instantaneous jobs (e.g. starting of targets, sockets, slices, or
Type=simple services) the log shows the job completion
before starting:
systemd[1]: Created slice -.slice.
systemd[1]: Starting -.slice.
systemd[1]: Created slice System Slice.
systemd[1]: Starting System Slice.
systemd[1]: Listening on Journal Audit Socket.
systemd[1]: Starting Journal Audit Socket.
systemd[1]: Reached target Timers.
systemd[1]: Starting Timers.
...
The reason is that the job completes before the ->start() method returns
and only then does unit_start() print the "Starting ..." message.
The same thing happens when stopping units.
Rather than fixing the order of the messages, let's just not emit the
Starting/Stopping message at all when the job completes instantaneously.
The job completion message is sufficient in this case.
|
|
core: include unit in path state transition debug logging.
|
|
|
|
"systemctl daemon-reload" should also update the manager defaults from
/etc/systemd/system.conf.
For details, see:
http://lists.freedesktop.org/archives/systemd-devel/2015-June/033062.html
Amended to use manager_set_defaults() as common function.
|
|
fileio: consolidate write_string_file*()
|
|
|
|
The latest consolidation cleanup of write_string_file() revealed some users
of that helper which should have used write_string_file_no_create() in the
past but didn't. Basically, all existing users that write to files in /sys
and /proc should not expect to write to a file which is not yet existant.
|
|
Merge write_string_file(), write_string_file_no_create() and
write_string_file_atomic() into write_string_file() and provide a flags mask
that allows combinations of atomic writing, newline appending and automatic
file creation. Change all users accordingly.
|
|
Whoopsy, forgot to 'git add' this, sorry.
|
|
Just like we conditionalize loading kdbus.ko, we should conditionalize
mounting kdbusfs. Otherwise, we might run with kdbus if it is builtin,
even though the user didn't want this.
|
|
Avoid late bail-out based on a condition. This makes code hard to read.
Instead, reverse the forwarding-condition.
|
|
On dbus1, we receive systemd1.Agent signals via the private socket, hence
it's trusted. However, on kdbus we receive it on the system bus. We must
make sure it's sent by UID=0, otherwise unprivileged users can fake it.
Furthermore, never forward broadcasts we sent ourself. This might happen
on kdbus, as we forward the message on the same bus we received it on,
thus ending up in an endless loop.
|
|
socket: Set SO_REUSEPORT before bind()
|