| Age | Commit message (Collapse) | Author |
|---|
|
|
|
If we evict a session position, we open the position slot for future
sessions. However, there might already be another session on the same
position if both were started on the same VT. This is currently done if
gdm spawns the session on its own Xserver.
Hence, look for such a session on pos-eviction and claim the new slot
immediately.
|
|
GREEDY_REALLOC takes a pointer to the real size, not the array-width as
argument. Therefore, our array is currently way to small to keep the seat
positions.
Introduce GREEDY_REALLOC0_T() as typed version of GREEDY_REALLOC and store
the array-width instead of array-size.
|
|
KillUserProcesses=yes/no should be ignored when termination is
explicitly requested.
|
|
Use PID_FMT/USEC_FMT/... in more places.
Also update logind error messages to print the full path to a file that
failed. This should make debugging easier for people who do not know
off the top of their head where logind stores it state.
|
|
logind has no concept of session ordering. Sessions have a unique name,
some attributes about the capabilities and that's already it. There is
currently no stable+total order on sessions. If we use the logind API to
switch between sessions, we are faced with an unordered list of sessions
we have no clue of.
This used to be no problem on seats with VTs or on seats with only a
single active session. However, with the introduction of multi-session
capability for seats without VTs, we need to find a way to order sessions
in a stable way.
This patch introduces session "positions". A position is a simple integer
assigned to a session which is never changed implicitly (currently, we
also don't change it explicitly, but that may be changed someday). For
seats with VTs, we force the position to be the same as the VTnr. Without
VTs, we simply find the lowest unassigned number and use it as position.
If position-assignment fails or if, for any reason, we decide to not
assign a position to a session, the position is set to 0 (which is treated
as invalid position).
During session_load() or if two sessions have the same VTnr, we may end up
with two sessions with the same position (this shouldn't happen, but lets
be fail-safe in case some other part of the stack fails). This case is
dealt with gracefully by ignoring any session but the first session
assigned to the position. Thus, session->pos is a hint, seat->positions[i]
is the definite position-assignment. Always verify both match in case you
need to modify them!
Additionally, we introduce SwitchTo(unsigned int) on the seat-dbus-API.
You can call it with any integer value != 0 and logind will try to switch
to the request position. If you implement a compositor or any other
session-controller, you simply watch for ctrl+alt+F1 to F12 and call
SwitchTo(Fx). logind will figure a way out deal with this number.
For convenience, we also introduce SwitchToNext/Previous(). It should be
called on ctrl+alt+Left/Right (like the kernel-console used to support).
Note that the public API (SwitchTo*()) is *not* bound to the underlying
logic that is implemented now. We don't export "session-positions" on the
dbus/C API! They are an implementation detail. Instead, the SwitchTo*()
API is supposed to be a hint to let logind choose the session-switching
logic. Any foreground session-controller is free to enumerate/order
existing sessions according to their needs and call Session.Activate()
manually. But the SwitchTo*() API provides a uniform behavior across
session-controllers.
Background: Session-switching keys depend on the active keymap. The XKB
specification provides the XKB_KEY_XF86Switch_VT_1-12 key-symbols which
have to be mapped by all keymaps to allow session-switching. It is usually
bound to ctrl+alt+Fx but may be set differently. A compositor passes any
keyboard input to XKB before passing it to clients. In case a key-press
invokes the XKB_KEY_XF86Switch_VT_x action, the keypress is *not*
forwarded to clients, but instead a session-switch is scheduled.
This actually prevents us from handling these keys outside of the session.
If an active compositor has a keymap with a different mapping of these
keys, and logind itself tries to catch these combinations, we end up with
the key-press sent to the compositor's clients *and* handled by logind.
This is *bad* and we must avoid this. The only situation where a
background process is allowed to handle key-presses is debugging and
emergency-keys. In these cases, we don't care for keymap mismatches and
accept the double-event. Another exception is unmapped keys like
PowerOff/Suspend (even though this one is controversial).
|
|
The only problem is that libgen.h #defines basename to point to it's
own broken implementation instead of the GNU one. This can be fixed
by #undefining basename.
|
|
Sessions on seat0 must pass us a vtnr, otherwise, you shouldn't try
attaching it to seat0. For seats without VTs, we do the exact opposite: we
forbid VTs.
There can be odd situations if the session-files contain invalid
combinations. However, we try to keep sessions alive and restore state as
good as possible.
|
|
Fix the whole code to use "unsigned int" for vtnr. 0 is an invalid vtnr so
we don't need negative numbers at all.
Note that most code already assumes it's unsigned so in case there's a
negative vtnr, our code may, under special circumstances, silently break.
So this patch makes sure all sources of vtnrs verify the validity. Also
note that the dbus api already uses unsigned ints.
|
|
Existing applications like gdm already depend on new sessions to get
immediately activated on seats without VTs. Fixes a bug reported as:
[systemd-devel] systemd 208:trouble with inactive user sessions at non-seat0 seats
This patch restores the original behavior. We either need to add a new
flag for session-creation or some other heuristic to avoid activating new
sessions in the future.
|
|
|
|
each invocation
We can determine the list entry type via the typeof() gcc construct, and
so we should to make the macros much shorter to use.
|
|
We only send the PropertyChanged signal for the to-be-activated session
but not for the to-be-deactivated one. Fix that so both listeners get
notified about the new state.
|
|
This enables the multi-session capability for seats that don't have VTs.
For legacy seats with VTs, everything stays the same. However, all other
seats now also get the multi-session capability.
The only feature that was missing was session-switching. As logind can
force a session-switch and signal that via the "Active" property, we only
need a way to allow synchronized/delayed session switches. Compositors
need to cleanup some devices before acknowledging the session switch.
Therefore, we use the session-devices to give compositors a chance to
block a session-switch until they cleaned everything up.
If you activate a session on a seat without VTs, we send a PauseDevice
signal to the active session for every active device. Only once the
session acknowledged all these with a PauseDeviceComplete() call, we
perform the final session switch.
One important note is that delayed session-switching is meant for
backwards compatibility. New compositors or other sessions should really
try to deal correctly with forced session switches! They only need to
handle EACCES/EPERM from syscalls and treat them as "PauseDevice" signal.
Following logind patches will add a timeout to session-switches which
forces the switch if the active session does not react in a timely
fashion. Moreover, explicit ForceActivate() calls might also be supported.
Hence, sessions must not crash if their devices get paused.
|
|
A session-device is a device that is bound to a seat and used by a
session-controller to run the session. This currently includes DRM, fbdev
and evdev devices. A session-device can be created via RequestDevice() on
the dbus API of the session. You can drop it via ReleaseDevice() again.
Once the session is destroyed or you drop control of the session, all
session-devices are automatically destroyed.
Session devices follow the session "active" state. A device can be
active/running or inactive/paused. Whenever a session is not the active
session, no session-device of it can be active. That is, if a session is
not in foreground, all session-devices are paused.
Whenever a session becomes active, all devices are resumed/activated by
logind. If it fails, a device may stay paused.
With every session-device you request, you also get a file-descriptor
back. logind keeps a copy of this fd and uses kernel specific calls to
pause/resume the file-descriptors. For example, a DRM fd is muted
by logind as long as a given session is not active. Hence, the fd of the
application is also muted. Once the session gets active, logind unmutes
the fd and the application will get DRM access again.
This, however, requires kernel support. DRM devices provide DRM-Master for
synchronization, evdev devices have EVIOCREVOKE (pending on
linux-input-ML). fbdev devices do not provide such synchronization methods
(and never will).
Note that for evdev devices, we call EVIOCREVOKE once a session gets
inactive. However, this cannot be undone (the fd is still valid but mostly
unusable). So we reopen a new fd once the session is activated and send it
together with the ResumeDevice() signal.
With this infrastructure in place, compositors can now run without
CAP_SYS_ADMIN (that is, without being root). They use RequestControl() to
acquire a session and listen for devices via udev_monitor. For every
device they want to open, they call RequestDevice() on logind. This
returns a fd which they can use now. They no longer have to open the
devices themselves or call any privileged ioctls. This is all done by
logind.
Session-switches are still bound to VTs. Hence, compositors will get
notified via the usual VT mechanisms and can cleanup their state. Once the
VT switch is acknowledged as usual, logind will get notified via sysfs and
pause the old-session's devices and resume the devices of the new session.
To allow using this infrastructure with systems without VTs, we provide
notification signals. logind sends PauseDevice("force") dbus signals to
the current session controller for every device that it pauses. And it
sends ResumeDevice signals for every device that it resumes. For
seats with VTs this is sent _after_ the VT switch is acknowledged. Because
the compositor already acknowledged that it cleaned-up all devices.
However, for seats without VTs, this is used to notify the active
compositor that the session is about to be deactivated. That is, logind
sends PauseDevice("force") for each active device and then performs the
session-switch. The session-switch changes the "Active" property of the
session which can be monitored by the compositor. The new session is
activated and the ResumeDevice events are sent.
For seats without VTs, this is a forced session-switch. As this is not
backwards-compatible (xserver actually crashes, weston drops the related
devices, ..) we also provide an acknowledged session-switch. Note that
this is never used for sessions with VTs. You use the acknowledged
VT-switch on these seats.
An acknowledged session switch sends PauseDevice("pause") instead of
PauseDevice("force") to the active session. It schedules a short timeout
and waits for the session to acknowledge each of them with
PauseDeviceComplete(). Once all are acknowledged, or the session ran out
of time, a PauseDevice("force") is sent for all remaining active devices
and the session switch is performed.
Note that this is only partially implemented, yet, as we don't allow
multi-session without VTs, yet. A follow up commit will hook it up and
implemented the acknowledgements+timeout.
The implementation is quite simple. We use major/minor exclusively to
identify devices on the bus. On RequestDevice() we retrieve the
udev_device from the major/minor and search for an existing "Device"
object. If no exists, we create it. This guarantees us that we are
notified whenever the device changes seats or is removed.
We create a new SessionDevice object and link it to the related Session
and Device. Session->devices is a hashtable to lookup SessionDevice
objects via major/minor. Device->session_devices is a linked list so we
can release all linked session-devices once a device vanishes.
Now we only have to hook this up in seat_set_active() so we correctly
change device states during session-switches. As mentioned earlier, these
are forced state-changes as VTs are currently used exclusively for
multi-session implementations.
Everything else are hooks to release all session-devices once the
controller changes or a session is closed or removed.
|
|
We currently use seat_can_multi_session() to test for two things:
* whether the seat can handle session-switching
* whether the seat has VTs
As both are currently logically equivalent, we didn't care. However, we
want to allow session-switching on seats without VTs, so split this helper
into:
* seat_can_multi_session(): whether session-switching is supported
* seat_has_vts(): whether the seat has VTs
Note that only one seat on a system can have VTs. There is only one set of
them. We automatically assign them to seat0 as usual.
With this patch in place, we can easily add new session-switching/tracking
methods without breaking any VT code as it is now protected by has_vts(),
no longer by can_multi_session().
|
|
A seat provides text-logins if it has VTs. This is always limited to seat0
so the seat_is_seat0() check is correct. However, if VTs are disabled, no
seat provides text-logins so we also need to check for the console-fd.
This was previously:
return seat_is_vtconsole();
It looked right, but was functionally equivalent to seat_is_seat0(). The
rename of this helper made it more obvious that it is missing the VT test.
|
|
The seat->vtconsole member always points to the default seat seat0. Even
if VTs are disabled, it's used as default seat. Therefore, rename it to
seat0 to correctly state what it is.
This also changes the seat files in /run from IS_VTCONSOLE to IS_SEAT0. It
wasn't used by any code, yet, so this seems fine.
While we are at it, we also remove every "if (s->vtconsole)" as this
pointer is always valid!
|
|
Session compositors need access to fbdev, DRM and evdev devices if they
control a session. To make logind pass them to sessions, we need to
listen for them actively.
However, we avoid creating new seats for non master-of-seat devices. Only
once a seat is created, we start remembering all other session devices. If
the last master-device is removed (even if there are other non-master
devices still available), we destroy the seat. This is the current
behavior, but we need to explicitly implement it now as there may be
non-master devices in the seat->devices list.
Unlike master devices, we don't care whether our list of non-master
devices is complete. We don't export this list but use it only as cache if
sessions request these devices. Hence, if a session requests a device that
is not in the list, we will simply look it up. However, once a session
requested a device, we must be notified of "remove" udev events. So we
must link the devices somehow into the device-list.
Regarding the implementation, we now sort the device list by the "master"
flag. This guarantees that master devices are at the front and non-master
devices at the tail of the list. Thus, we can easily test whether a seat
has a master device attached.
|
|
The MESSAGE_ID=... stanza will appear in countless number of places.
It is just too long to write it out in full each time.
Incidentally, this also fixes a typo of MESSSAGE is three places.
|
|
Before, after the timeout, a session would be timestamped as idle
since 'last activity' + 'idle timeout'. Now, it is timestamped as idle
since 'last activity'.
Before, after all sessions were idle, the seat would be marked with as
idle with the timestamp of the oldest idle session. Now it is
marked with the timestamp of the youngest idle session.
Both changes seem to me to be closer to natural understanding of
idleness: the time since last activity counts.
|
|
same user.
|
|
|
|
Since we boot so fast now that gdm might get started before the
graphics drivers are properly loaded and probed we might end up
announcing seat0 to gdm before it has graphics capabilities. Which will
cause gdm/X11 cause to fail later on.
To fix this race, let's expose CanGraphical and CanTTY fields on all
seats, which clarify whether a seat is suitable for gdm resp, suitable
for text logins. gdm then needs to watch CanGraphical and spawn X11 on
it only if it is true.
This way:
USB graphics seats will expose CanGraphical=yes, CanTTY=no
Machines with no graphics drivers at all, but a text console:
CanGraphical=no, CanTTY=yes
Machines with CONFIG_VT turned off: CanGraphical=yes, CanTTY=no
And the most important case: seat0 where the graphics driver has not
been probed yet boot up with CanGraphical=no, CanTTY=yes first, which
then changes to CanGraphical=yes as soon as the probing is complete.
|
|
context
|
|
|
|
We finally got the OK from all contributors with non-trivial commits to
relicense systemd from GPL2+ to LGPL2.1+.
Some udev bits continue to be GPL2+ for now, but we are looking into
relicensing them too, to allow free copy/paste of all code within
systemd.
The bits that used to be MIT continue to be MIT.
The big benefit of the relicensing is that closed source code may now
link against libsystemd-login.so and friends.
|
|
Only 34 of 74 tools need libselinux linked, and libselinux is a pain
with its unconditional library constructor.
|
|
with left-over sessions
|
|
don't pretend we could do VT switching
|
|
|
