| Age | Commit message (Collapse) | Author |
|---|
|
Still keep the non-socket activation code around for starting from the commandline, but
will likely drop that too in the future.
|
|
Default to timing out after 120 seconds without a network connection. Setting a
timeout of 0 disables the timeout.
|
|
|
|
We would otherwise wait for the interface to be completely configured, which
could take considerable time with IPv4LL. As a result nspawn was very slow
at obtaining IP addresses.
|
|
In addition to the loopback device, also explicitly configured devices to be ignored.
Suggested by Charles Devereaux <systemd@guylhem.net>.
|
|
|
|
Once IPv6 addresses have been acquired, assign these to the interface
with the prefix lengths taken from the ICMPv6 Router Advertisement
handling code. The preferred and valid IPv6 address lifetimes are
handed to the kernel which will clean up them if not renewed in time.
When a prefix announced via Router Advertisements expires, find all
addresses that match that prefix and update the address to have a
prefix length of 128 causing the prefix to be off-link.
|
|
This patch introduces ipv6 gre and gretap.
test:
ip6gre.netdev:
[NetDev]
Name=ip6gretap
Kind=ip6gretap
[Tunnel]
Local=2a00:ffde:4567:edde::4987
Remote=2001:473:fece:cafe::5179
ip6gre.network:
[Match]
Name=eno16777736
[Network]
Tunnel=ip6gretap
ip link
6: ip6gre@eno16777736: <POINTOPOINT,NOARP> mtu 1448 qdisc noop state
DOWN mode DEFAULT group default
link/gre6 2a:00:ff:de:45:67:ed:de:00:00:00:00:00:00:49:87 peer
20:01:04:73:fe:ce:ca:fe:00:00:00:00:00:00:51:79
|
|
This patch enables networkd to create IP6 tunnels
example conf:
ipip6.netdev:
[NetDev]
Name=ipip6-tunnel
Kind=ip6tnl
[Tunnel]
Mode=ip4ipv6
Local=2a00:ffde:4567:edde::4987
Remote=2001:473:fece:cafe::5179
ipip6.network
[Match]
Name=wlan0
[Network]
Tunnel=ipip6-tunnel
23: ipip6-tunnel@wlan0: <POINTOPOINT,NOARP> mtu 1452 qdisc noop state
DOWN mode DEFAULT group default
link/tunnel6 2a00:ffde:4567:edde::4987 peer 2001:473:fece:cafe::5179
|
|
This patch introdeces gretap to networkd
|
|
|
|
subscibe->subscribe
|
|
|
|
|
|
/proc/sys/net/ipv4/ip_forward
We need to turn on /proc/sys/net/ipv4/ip_forward before the
per-interface forwarding setting is useful, hence let's propagate the
per-interface setting once to the system-wide setting.
Due to the unclear ownership rules of that flag, and the fact that
turning it on also has effects on other sysctl flags we try to minimize
changes to the flag, and only turn it on once. There's no logic to
turning it off again, but this should be fairly unproblematic as the
per-interface setting defaults to off anyway.
|
|
|
|
|
|
This introduces am AddressFamilyBoolean type that works more or less
like a booleaan, but can optionally turn on/off things for ipv4 and ipv6
independently. THis also ports the DHCP field over to it.
|
|
This adds two new settings to networkd's .network files:
IPForwarding=yes and IPMasquerade=yes. The former controls the
"forwarding" sysctl setting of the interface, thus controlling whether
IP forwarding shall be enabled on the specific interface. The latter
controls whether a firewall rule shall be installed that exposes traffic
coming from the interface as coming from the local host to all other
interfaces.
This also enables both options by default for container network
interfaces, thus making "systemd-nspawn --network-veth" have network
connectivity out of the box.
|
|
https://bugs.freedesktop.org/show_bug.cgi?id=83270
|
|
Those values are based on a file we read from disk, so we should
verify everything we receive, and make sure everything we print
is sensible.
Also, print fractional seconds for TTL.
|
|
|
|
usec_t is defined as 64 bit wide, but long is 32 bit on many archs.
|
|
Make sure to test the right variable for NULL.
|
|
|
|
|
|
|
|
This patch integrates LLDP with networkd.
Example conf:
file : lldp.network
[Match]
Name=em1
[Network]
LLDP=yes
|
|
|
|
|
|
|
|
level rather than debug
|
|
|
|
without parameters
|
|
from all interfaces
|
|
further arguments is passed
|
|
|
|
|
|
Let's stick to generic sections that describe the general technology,
instead of specific per-object sections, unless we really have a reason
to do that otherwise.
|
|
When ICMPv6 Other information is received, enable Information request
in DHCPv6. If the DHCPv6 client already exists, only update the client
if there is a transition from Other to Managed state.
|
|
Handle all aspects of ICMPv6 and DHCPv6 in a file of its own as is done
with DHCPv4 and IPv4LL.
|
|
It is no longer used after 45af44d47da6933b260c734ad9ff721f63f80a4d
|
|
The kernel always returns all addresses, rather than only for the given link, so let's only enumerate once.
|
|
|
|
|
|
|
|
This file won't exist on kernels earlier than 3.17.
|
|
|
|
This allows the default link settings (set in .link files) to be overridden per Network. Only MTU and MACAddress is supported for now.
|
|
This has been requested repeatedly, so let's give it a go. We explicitly do not allow matching
on names that have already been changed (from a previous udev run, or otherwise), and matching
on unpredictable names (ethX) is discouraged (but not currently disallowed).
We also currently allow:
[Match]
Name=veth0
[Link]
Name=my-name0
SomeOtherSetting=true
Which means that the link file will be applied the first time it is invoked, but
not on subsequent invocations, which may be surprising.
|
