| Age | Commit message (Collapse) | Author |
|---|
|
When an address is configured to be all zeroes, networkd will now
automatically find a locally unused network of the right size from a
list of pre-configured pools. Currently those pools are 10.0.0.0/8,
172.16.0.0/12, 192.168.0.0/16 and fc00::/7, i.e. the network ranges for
private networks. They are compiled in, but should be configurable
eventually.
This allows applying the same configuration to a large number of
interfaces with each time a different IP range block, and management of
these IP ranges is fully automatic.
When allocating an address range from the pool it is made sure the range
is not used otherwise.
|
|
|
|
of it everywhere
|
|
There is no need to explicitly check version of L3 protocol in the
ethernet header because we bind socket with .sll_protocol set to
ETH_P_IP, thus we only receive IPv4 packets on the socket.
|
|
make sure they are started before and stopped after any LUKS setup
https://bugzilla.redhat.com/show_bug.cgi?id=1097938
|
|
creating them first, and relabeling them afterwards
|
|
|
|
https://bugzilla.redhat.com/show_bug.cgi?id=1081429
|
|
|
|
|
|
|
|
|
|
|
|
In programs like eog and gimp the transparant background did not
look very good.
Similar fix from the one done in systemd-analyze (418e3750)
|
|
We were comparing against our own internal enum rather than the kernel exposed one.
Found by Thomas Ritter.
|
|
For efficiency, we group bytes together before adding them up. This
is guaranteed to always work (regardless of the byte order) as long
as the i-th byte in each group lign up with the i-th byte in each
other group.
On big-endian machines this broke when handling the trailing few bytes
which did not make up a full group of 4 bytes. This patch fixes the
problem by explicitly creating a 4 byte zero-padded group out of the
trailing bytes.
Reported and tested by Thomas Ritter <th.ritter@gmx.at>.
|
|
This was backwards. The symlink itself points to the source unit, not
the other way around.
|
|
|
|
|
|
container
It's generally preferrable to conditionalize on the actual ability to do
something then the context we run in.
|
|
|
|
This is based on parts of similar patches from Michael Marineau and
Lukas Nykrin, but simply uses strappenda3().
|
|
"systemctl disable"
|
|
|
|
DefaultInstance= setting
|
|
cmdline
"debug" should apply to all tools, but "quiet" only to PID1.
|
|
outside of search path
|
|
instances
|
|
The DefaultInstance= name is used when enabling template units when only
specifying the template name, but no instance.
Add DefaultInstance=tty1 to getty@.service, so that when the template
itself is enabled an instance for tty1 is created.
This is useful so that we "systemctl preset-all" can work properly,
because we can operate on getty@.service after finding it, and the right
instance is created.
|
|
only after traversing all search directories
Let's always make sure to look in all search directories for the full
unit names first, before looking for templates for them.
|
|
creating a symlink
|
|
|
|
|
|
do all-unit preset operations
The new "systemctl preset-all" command may now be used to put all
installed units back into the enable/disable state the vendor/admin
encoded in preset files.
Also, introduce "systemctl --preset-mode=enable-only" and "systemctl
--preset-mode=disable-only" to only apply the enable or only the disable
operations of a "systemctl preset" or "systemctl preset-all" operation.
"systemctl preset-all" implements this RFE:
https://bugzilla.redhat.com/show_bug.cgi?id=630174
|
|
|
|
|
|
|
|
We need to check for the last dot, not the first one in a unit name, for
the suffix. Correct that.
|
|
|
|
|
|
add tests for:
- hashmap_remove_and_put
- hashmap_first_key
- hashmap_last
- hashmap_steal_first_key
- hashmap_clear_free_free
|
|
|
|
|
|
Unref tunnel while shutting down
|
|
This patch enables netwokd to create vxlan
Changes:
Added:
1. File networkd networkd-vxlan.c
2. to netdev
bool learning
struct in_addr group
uint64_t vxlanid;
3. VXLAN subsection and config
parameters
|
|
Rename the netdev variables. Remove tunnel_
so that it can be reused .
|
|
This patch adds vxlan rtnl attributes to sd-rtnl
|
|
|
|
Process 1 (aka init) needs to be started with an empty signal mask.
That includes the process 1 that's started after the initrd is finished.
When the initrd is using systemd (as it does with dracut based initrds)
then it is systemd that calls the real init. Normally this is systemd
again, except when the user uses for instance "init=/bin/bash" on the
kernel command line.
|
|
This is similar to malloc_multiply() and friends. It is realloc() with a
multiplication-overflow check.
|
