| Age | Commit message (Collapse) | Author |
|---|
|
This causes the container to shut down cleanly when the service is
stopped.
|
|
Create initial stamp file with compiled-in time to prevent bootups
with clocks in the future from storing invalid timestamps.
At shutdown, only update the timestamp if we got an authoritative
time to store.
|
|
|
|
boot using this
This is useful to make sure the system clock stays monotonic even on
systems that lack an RTC.
Also, why we are at it, also use the systemd release time for bumping
the clock, since it's a slightly less bad than starting with jan 1st,
1970.
This also moves timesyncd into the early bootphase, in order to make
sure this initial bump is guaranteed to have finished by the time we
start real daemons which might write to the file systemd and thus
shouldn't leave 1970's timestamps all over the place...
|
|
Also remove the equivalent functionality from networkd.
|
|
|
|
with CAP_SYS_TIME)
|
|
This reverts commit a555350d47c4b70d716a63424933b34902c98300.
This did not fix the problem, just made it harder to hit.
|
|
|
|
This is needed for the network monitor to work (as it requires networkd to set up the correct directories first).
|
|
Remember to drop this when the kernel gains autoloading for all netdev kinds.
|
|
|
|
To make sure we don't delay boot on systems where (some) network links are managed by someone else
we don't block if something else has successfully brought up a link.
We will still block until all links we are aware of that are managed by networkd have been
configured, but if no such links exist, and someone else have configured a link sufficiently
that it has a carrier, it may be that the link is ready so we should no longer block.
Note that in all likelyhood the link is not ready (no addresses/routes configured),
so whatever network managment daemon configured it should provide a similar wait-online
service to block network-online.target until it is ready.
The aim is to block as long as we know networking is not fully configured, but no longer. This
will allow systemd-networkd-wait-online.service to be enabled on any system, even if we don't
know whether networkd is the main/only network manager.
Even in the case networking is fully configured by networkd, the default behavior may not be
sufficient: if two links need to be configured, but the first is fully configured before the
second one appears we will assume the network is up. To work around that, we allow specifying
specific devices to wait for before considering the network up.
This unit is enabled by default, just like systemd-networkd, but will only be pulled in if
anyone pulls in network-online.target.
|
|
|
|
Otherwise we will not be able to queuery whether devices are initialized on kdbus enabled systems.
|
|
|
|
|
|
/tmp is only available in later boot, and we shouldn't create private
subdirs in it hence, while we are still in early boot.
|
|
Keep mounts done by udev rules private to udevd. Also, document how
MountFlags= may be used for this.
|
|
this is useful
|
|
long-running daemons
|
|
Add a new config 'Activating' directive which denotes whether a busname
is actually registered on the bus. It defaults to 'yes'.
If set to 'no', the .busname unit only uploads policy, which will remain
active as long as the unit is running.
|
|
Add the first 3270 terminal device that is associated with the Linux preferred
console to the list of virtualization consoles. This is required to
automatically start a getty if the conmode=3270 kernel parameter is specified
for Linux on z/VM instances. Note that a queued upstream patch also enable
the 3270 terminal device if it is associated with the Linux preferred console.
How
To successfully start agetty on a 3270 terminal, a change in the agetty
parameter order is required. Previously, agetty would started like this:
/sbin/agetty --keep-baud 3270/tty1 115200,38400,9600 TERM
The agetty program interprets the "3270/tty1" as baud rate and fails to start
with the "bad speed: 3270/tty1" error message. Fixing this in agetty is more
complex rather than reordering the command line parameters like this:
/sbin/agetty --keep-baud 115200,38400,9600 3270/tty1 TERM
According to agetty sources and "agetty --help", agetty accepts the "tty",
"baudrate tty", and "tty baudrate" specifications.
P.S. The "tty: Set correct tty name in 'active' sysfs attribute" introduces
a change to display the terminal device which is associated with the
Linux preferred console. This change helps to let systemd handle this
particular case only. Without the changes of this commit, no additional
3270 terminal device can be managed by systemd.
https://git.kernel.org/cgit/linux/kernel/git/gregkh/tty.git/commit/?id=723abd87f6e536f1353c8f64f621520bc29523a3
|
|
|
|
|
|
The instance name is never escaped in the udev rule, but unescaped in the unit.
This results in the following error message on Asus boards:
Failed to get backlight or LED device 'backlight:eeepc/wmi': No such file or directory
|
|
|
|
|
|
|
|
This makes it easier to manually enable and disable
specific gettys, and also mirrors getty@.service.
http://lists.freedesktop.org/archives/systemd-devel/2014-February/017329.html
|
|
[tomegun: pruned the commit message as not to contradict the follow-up commit]
|
|
That is, without --enable-kdbus and kdbus running.
With --enable-kdbus things are more complicated, because dbus might be
necessary, if kdbus is missing at runtime. If it is not necessary,
the socket will be started, which is not imporant, but not the service.
|
|
|
|
process, but SIGKILL to all daemon processes
This should fix some race with terminating systemd --user, where the
system systemd instance might race against the user systemd instance
when sending SIGTERM.
|
|
We may not have a dbus daemon in the initrd (until we can rely on kdbus). In
this case, simply ignore any attempts at using the bus. There is only one user
for now, but surely more to come.
In order to work reliably in the real root without kdbus, but at the same time
don't delay boot when kdbus is in use, order ourselves after dbus.service.
|
|
They were supposed to make it easy to make the default.target a symlink
to these targets, but this was never advertised and we have a better
command for this now in "systemctl set-default". Since the install
section makes the output of "systemctl list-unit-files" confusing (since
it makes the units appear as "disabled"), let's drop the sections.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
As suggested by Kay, it is better to describe what is done,
not what might happen.
|
|
|
|
|
|
|
|
Various operations done by systemd-tmpfiles may only be safely done at
boot (e.g. removal of X lockfiles in /tmp, creation of /run/nologin).
Other operations may be done at any point in time (e.g. setting the
ownership on /{run,var}/log/journal). This distinction is largely
orthogonal to the type of operation.
A new switch --unsafe is added, and operations which should only be
executed during bootup are marked with an exclamation mark in the
configuration files. systemd-tmpfiles.service is modified to use this
switch, and guards are added so it is hard to re-start it by mistake.
If we install a new version of systemd, we actually want to enforce
some changes to tmpfiles configuration immediately. This should now be
possible to do safely, so distribution packages can be modified to
execute the "safe" subset at package installation time.
/run/nologin creation is split out into a separate service, to make it
easy to override.
https://bugzilla.redhat.com/show_bug.cgi?id=1043212
https://bugzilla.redhat.com/show_bug.cgi?id=1045849
|
|
Condition for /lib (necessary for split /usr) was missing from the unit.
Some changes which were done in tmpfiles.d(5) were not carried over to
systemd-tmpfiles(1).
Also use markup where possible.
|
