systemd.mountsystemdDeveloperLennartPoetteringlennart@poettering.netsystemd.mount5systemd.mountsystemd mount configuration filessystemd.mountDescriptionA unit configuration file whose name ends in
.mount encodes information about
a file system mount point controlled and supervised by
systemd.This man page lists the configuration options
specific to this unit type. See
systemd.unit5
for the common options of all unit configuration
files. The common configuration items are configured
in the generic [Unit] and [Install] sections. The
mount specific configuration options are configured
in the [Mount] section.Additional options are listed in
systemd.exec5.Mount units must be named after the mount point
directories they control. Example: the mount point
/home/lennart must be configured
in a unit file
home-lennart.mount. For details
about the escaping logic used to convert a file system
path to a unit name see
systemd.unit5.Optionally, a mount unit may be accompanied by
an automount unit, to allow on-demand or parallelized
mounting. See
systemd.automount5.If an mount point is beneath another mount point
in the file system hierarchy, a dependency between both
units is created automatically.Mount points created at runtime independent on
unit files or /etc/fstab will be
monitored by systemd and appear like any other mount
unit in systemd.<filename>fstab</filename>Mount units may either be configured via unit
files, or via /etc/fstab (see
fstab5
for details).When reading /etc/fstab a
few special mount options are understood by systemd
which influence how dependencies are created for mount
points from /etc/fstab. If
is specified as
mount option, then systemd will create a dependency of
type from either
local-fs.target or
remote-fs.target, depending
whether the file system is local or remote. If
is set, an
automount unit will be created for the file system. See
systemd.automount5
for details.If a mount point is configured in both
/etc/fstab and a unit file, the
configuration in the latter takes precedence.OptionsMount files must include a [Mount] section,
which carries information about the file system mount points it
supervises. A number of options that may be used in
this section are shared with other unit types. These
options are documented in
systemd.exec5. The
options specific to the [Mount] section of mount
units are the following:What=Takes an absolute path
of a device node, file or other
resource to mount. See
mount8
for details. If this refers to a
device node, a dependency on the
respective device unit is
automatically created. (See
systemd.device5 for more information.)
This option is
mandatory.Where=Takes an absolute path
of a directory of the mount point. If
the mount point is not existing at
time of mounting, it is created. This
string must be reflected in the unit
file name. (See above.) This option is
mandatory.Type=Takes a string for the
filesystem type. See
mount8
for details. This setting is
optional.Options=Mount options to use
when mounting. This takes a comma
seperated list of options. This
setting is optional.DirectoryMode=Directories of mount
points (and any parent directories)
are automatically created if
needed. This option specifies the file
system access mode used when creating
these directories. Defaults to
0755.TimeoutSec=Configures the time to
wait for the mount command to
finish. If a command does not exit
within the configured time the mount
will be considered failed and be shut
down again. All commands still running
will be terminated forcibly via
SIGTERM, and after another delay of
this time with SIGKILL. (See
below.)
Takes a unit-less value in seconds, or
a time span value such as "5min
20s". Pass 0 to disable the timeout
logic. Defaults to
60s.KillMode=Specifies how
processes of this mount shall be
killed. One of
,
,
,
.This option is mostly equivalent
to the
option of service files. See
systemd.service5
for details.See Alsosystemd8,
systemctl8,
systemd.unit5,
systemd.exec5,
systemd.device5,
mount8