Initial import

1 files changed, 115 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
new file mode 100644
index 000000000..02c27004d
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -0,0 +1,115 @@
+NVIDIA Tegra Power Management Controller (PMC)
+
+The PMC block interacts with an external Power Management Unit. The PMC
+mostly controls the entry and exit of the system from different sleep
+modes. It provides power-gating controllers for SoC and CPU power-islands.
+
+Required properties:
+- name : Should be pmc
+- compatible : For Tegra20, must contain "nvidia,tegra20-pmc".  For Tegra30,
+  must contain "nvidia,tegra30-pmc".  For Tegra114, must contain
+  "nvidia,tegra114-pmc".  For Tegra124, must contain "nvidia,tegra124-pmc".
+  Otherwise, must contain "nvidia,<chip>-pmc", plus at least one of the
+  above, where <chip> is tegra132.
+- reg : Offset and length of the register set for the device
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  "pclk" (The Tegra clock of that name),
+  "clk32k_in" (The 32KHz clock input to Tegra).
+
+Optional properties:
+- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal.
+  The PMU is an external Power Management Unit, whose interrupt output
+  signal is fed into the PMC. This signal is optionally inverted, and then
+  fed into the ARM GIC. The PMC is not involved in the detection or
+  handling of this interrupt signal, merely its inversion.
+- nvidia,suspend-mode : The suspend mode that the platform should use.
+  Valid values are 0, 1 and 2:
+  0 (LP0): CPU + Core voltage off and DRAM in self-refresh
+  1 (LP1): CPU voltage off and DRAM in self-refresh
+  2 (LP2): CPU voltage off
+- nvidia,core-power-req-active-high : Boolean, core power request active-high
+- nvidia,sys-clock-req-active-high : Boolean, system clock request active-high
+- nvidia,combined-power-req : Boolean, combined power request for CPU & Core
+- nvidia,cpu-pwr-good-en : Boolean, CPU power good signal (from PMIC to PMC)
+			   is enabled.
+
+Required properties when nvidia,suspend-mode is specified:
+- nvidia,cpu-pwr-good-time : CPU power good time in uS.
+- nvidia,cpu-pwr-off-time : CPU power off time in uS.
+- nvidia,core-pwr-good-time : <Oscillator-stable-time Power-stable-time>
+			      Core power good time in uS.
+- nvidia,core-pwr-off-time : Core power off time in uS.
+
+Required properties when nvidia,suspend-mode=<0>:
+- nvidia,lp0-vec : <start length> Starting address and length of LP0 vector
+  The LP0 vector contains the warm boot code that is executed by AVP when
+  resuming from the LP0 state. The AVP (Audio-Video Processor) is an ARM7
+  processor and always being the first boot processor when chip is power on
+  or resume from deep sleep mode. When the system is resumed from the deep
+  sleep mode, the warm boot code will restore some PLLs, clocks and then
+  bring up CPU0 for resuming the system.
+
+Hardware-triggered thermal reset:
+On Tegra30, Tegra114 and Tegra124, if the 'i2c-thermtrip' subnode exists,
+hardware-triggered thermal reset will be enabled.
+
+Required properties for hardware-triggered thermal reset (inside 'i2c-thermtrip'):
+- nvidia,i2c-controller-id : ID of I2C controller to send poweroff command to. Valid values are
+                             described in section 9.2.148 "APBDEV_PMC_SCRATCH53_0" of the
+                             Tegra K1 Technical Reference Manual.
+- nvidia,bus-addr : Bus address of the PMU on the I2C bus
+- nvidia,reg-addr : I2C register address to write poweroff command to
+- nvidia,reg-data : Poweroff command to write to PMU
+
+Optional properties for hardware-triggered thermal reset (inside 'i2c-thermtrip'):
+- nvidia,pinmux-id : Pinmux used by the hardware when issuing poweroff command.
+                     Defaults to 0. Valid values are described in section 12.5.2
+                     "Pinmux Support" of the Tegra4 Technical Reference Manual.
+
+Example:
+
+/ SoC dts including file
+pmc@7000f400 {
+	compatible = "nvidia,tegra20-pmc";
+	reg = <0x7000e400 0x400>;
+	clocks = <&tegra_car 110>, <&clk32k_in>;
+	clock-names = "pclk", "clk32k_in";
+	nvidia,invert-interrupt;
+	nvidia,suspend-mode = <1>;
+	nvidia,cpu-pwr-good-time = <2000>;
+	nvidia,cpu-pwr-off-time = <100>;
+	nvidia,core-pwr-good-time = <3845 3845>;
+	nvidia,core-pwr-off-time = <458>;
+	nvidia,core-power-req-active-high;
+	nvidia,sys-clock-req-active-high;
+	nvidia,lp0-vec = <0xbdffd000 0x2000>;
+};
+
+/ Tegra board dts file
+{
+	...
+	pmc@7000f400 {
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x40>;
+			nvidia,reg-addr = <0x36>;
+			nvidia,reg-data = <0x2>;
+		};
+	};
+	...
+	clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		clk32k_in: clock {
+			compatible = "fixed-clock";
+			reg=<0>;
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+	...
+};