Initial import

1 files changed, 118 insertions, 0 deletions

diff --git a/arch/cris/arch-v32/mach-a3/dram_init.S b/arch/cris/arch-v32/mach-a3/dram_init.S
new file mode 100644
index 000000000..ec8648be3
--- /dev/null
+++ b/arch/cris/arch-v32/mach-a3/dram_init.S
@@ -0,0 +1,118 @@
+/*
+ * DDR SDRAM initialization - alter with care
+ * This file is intended to be included from other assembler files
+ *
+ * Note: This file may not modify r8 or r9 because they are used to
+ * carry information from the decompresser to the kernel
+ *
+ * Copyright (C) 2005-2007 Axis Communications AB
+ *
+ * Authors:  Mikael Starvik <starvik@axis.com>
+ */
+
+/* Just to be certain the config file is included, we include it here
+ * explicitely instead of depending on it being included in the file that
+ * uses this code.
+ */
+
+#include <hwregs/asm/reg_map_asm.h>
+#include <hwregs/asm/ddr2_defs_asm.h>
+
+	;; WARNING! The registers r8 and r9 are used as parameters carrying
+	;; information from the decompressor (if the kernel was compressed).
+	;; They should not be used in the code below.
+
+	;; Refer to ddr2 MDS for initialization sequence
+
+	; 2. Wait 200us
+	move.d   10000, $r2
+1:	bne      1b
+	subq     1, $r2
+
+	; Start clock
+	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_phy_cfg), $r0
+	move.d   REG_STATE(ddr2, rw_phy_cfg, en, yes), $r1
+	move.d   $r1, [$r0]
+
+	; 2. Wait 200us
+	move.d   10000, $r2
+1:	bne      1b
+	subq     1, $r2
+
+	; Reset phy and start calibration
+	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_phy_ctrl), $r0
+	move.d   REG_STATE(ddr2, rw_phy_ctrl, rst, yes) | \
+		 REG_STATE(ddr2, rw_phy_ctrl, cal_rst, yes), $r1
+	move.d   $r1, [$r0]
+	move.d	 REG_STATE(ddr2, rw_phy_ctrl, cal_start, yes), $r1
+	move.d   $r1, [$r0]
+
+	; 2. Wait 200us
+	move.d   10000, $r2
+1:	bne      1b
+	subq     1, $r2
+
+	; Issue commands
+	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_ctrl), $r0
+	move.d   sdram_commands_start, $r2
+command_loop:
+	movu.b  [$r2+], $r1
+	movu.w  [$r2+], $r3
+do_cmd:
+	lslq     16, $r1
+	or.d     $r3, $r1
+	move.d   $r1, [$r0]
+	; 2. Wait 200us
+	move.d   10000, $r4
+1:	bne      1b
+	subq     1, $r4
+	cmp.d    sdram_commands_end, $r2
+	blo      command_loop
+	nop
+
+	; Set timing
+	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_timing), $r0
+	move.d   CONFIG_ETRAX_DDR2_TIMING, $r1
+	move.d   $r1, [$r0]
+
+	; Set latency
+	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_latency), $r0
+	move.d   CONFIG_ETRAX_DDR2_LATENCY, $r1
+	move.d   $r1, [$r0]
+
+	; Set configuration
+	move.d   REG_ADDR(ddr2, regi_ddr2_ctrl, rw_cfg), $r0
+	move.d   CONFIG_ETRAX_DDR2_CONFIG, $r1
+	move.d   $r1, [$r0]
+
+	ba after_sdram_commands
+	nop
+
+sdram_commands_start:
+	.byte regk_ddr2_deselect
+	.word 0
+	.byte regk_ddr2_pre
+	.word regk_ddr2_pre_all
+	.byte regk_ddr2_emrs2
+	.word 0
+	.byte regk_ddr2_emrs3
+	.word 0
+	.byte regk_ddr2_emrs
+	.word regk_ddr2_dll_en
+	.byte regk_ddr2_mrs
+	.word regk_ddr2_dll_rst
+	.byte regk_ddr2_pre
+	.word regk_ddr2_pre_all
+	.byte regk_ddr2_ref
+	.word 0
+	.byte regk_ddr2_ref
+	.word 0
+	.byte regk_ddr2_mrs
+	.word CONFIG_ETRAX_DDR2_MRS & 0xffff
+	.byte regk_ddr2_emrs
+	.word regk_ddr2_ocd_default | regk_ddr2_dll_en
+	.byte regk_ddr2_emrs
+	.word regk_ddr2_ocd_exit | regk_ddr2_dll_en | (CONFIG_ETRAX_DDR2_MRS >> 16)
+sdram_commands_end:
+	.align 1
+after_sdram_commands: