Linux-libre 4.4-gnupck-4.4-gnu

1 files changed, 0 insertions, 157 deletions

diff --git a/arch/cris/include/uapi/asm/etraxgpio.h b/arch/cris/include/uapi/asm/etraxgpio.h
index 461c089db..c6e7d57c8 100644
--- a/arch/cris/include/uapi/asm/etraxgpio.h
+++ b/arch/cris/include/uapi/asm/etraxgpio.h
@@ -11,26 +11,6 @@
  *       g1-g7 and g25-g31 is both input and outputs but on different pins
  *       Also note that some bits change pins depending on what interfaces
  *       are enabled.
- *
- * For ETRAX FS (CONFIG_ETRAXFS):
- * /dev/gpioa  minor 0,  8 bit GPIO, each bit can change direction
- * /dev/gpiob  minor 1, 18 bit GPIO, each bit can change direction
- * /dev/gpioc  minor 3, 18 bit GPIO, each bit can change direction
- * /dev/gpiod  minor 4, 18 bit GPIO, each bit can change direction
- * /dev/gpioe  minor 5, 18 bit GPIO, each bit can change direction
- * /dev/leds   minor 2, Access to leds depending on kernelconfig
- *
- * For ARTPEC-3 (CONFIG_CRIS_MACH_ARTPEC3):
- * /dev/gpioa  minor 0, 32 bit GPIO, each bit can change direction
- * /dev/gpiob  minor 1, 32 bit GPIO, each bit can change direction
- * /dev/gpioc  minor 3, 16 bit GPIO, each bit can change direction
- * /dev/gpiod  minor 4, 32 bit GPIO, input only
- * /dev/leds   minor 2, Access to leds depending on kernelconfig
- * /dev/pwm0   minor 16, PWM channel 0 on PA30
- * /dev/pwm1   minor 17, PWM channel 1 on PA31
- * /dev/pwm2   minor 18, PWM channel 2 on PB26
- * /dev/ppwm   minor 19, PPWM channel
- *
  */
 #ifndef _ASM_ETRAXGPIO_H
 #define _ASM_ETRAXGPIO_H
@@ -40,52 +20,12 @@
 #define ETRAXGPIO_IOCTYPE 43
 
 /* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */
-#ifdef CONFIG_ETRAX_ARCH_V10
 #define GPIO_MINOR_A 0
 #define GPIO_MINOR_B 1
 #define GPIO_MINOR_LEDS 2
 #define GPIO_MINOR_G 3
 #define GPIO_MINOR_LAST 3
 #define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
-#endif
-
-#ifdef CONFIG_ETRAXFS
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_C 3
-#define GPIO_MINOR_D 4
-#define GPIO_MINOR_E 5
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#define GPIO_MINOR_V 6
-#define GPIO_MINOR_LAST 6
-#else
-#define GPIO_MINOR_LAST 5
-#endif
-#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
-#endif
-
-#ifdef CONFIG_CRIS_MACH_ARTPEC3
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_C 3
-#define GPIO_MINOR_D 4
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#define GPIO_MINOR_V 6
-#define GPIO_MINOR_LAST 6
-#else
-#define GPIO_MINOR_LAST 4
-#endif
-#define GPIO_MINOR_FIRST_PWM 16
-#define GPIO_MINOR_PWM0 (GPIO_MINOR_FIRST_PWM+0)
-#define GPIO_MINOR_PWM1 (GPIO_MINOR_FIRST_PWM+1)
-#define GPIO_MINOR_PWM2 (GPIO_MINOR_FIRST_PWM+2)
-#define GPIO_MINOR_PPWM (GPIO_MINOR_FIRST_PWM+3)
-#define GPIO_MINOR_LAST_PWM GPIO_MINOR_PPWM
-#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST_PWM
-#endif
-
 
 
 /* supported ioctl _IOC_NR's */
@@ -139,101 +79,4 @@
 #define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output, */
 			      /* *arg updated with current output pins. */
 
-/* The following ioctl's are applicable to the PWM channels only */
-
-#define IO_PWM_SET_MODE     0x20
-
-enum io_pwm_mode {
-	PWM_OFF = 0,		/* disabled, deallocated */
-	PWM_STANDARD = 1,	/* 390 kHz, duty cycle 0..255/256 */
-	PWM_FAST = 2,		/* variable freq, w/ 10ns active pulse len */
-	PWM_VARFREQ = 3,	/* individually configurable high/low periods */
-	PWM_SOFT = 4		/* software generated */
-};
-
-struct io_pwm_set_mode {
-	enum io_pwm_mode mode;
-};
-
-/* Only for mode PWM_VARFREQ. Period lo/high set in increments of 10ns
- * from 10ns (value = 0) to 81920ns (value = 8191)
- * (Resulting frequencies range from 50 MHz (10ns + 10ns) down to
- * 6.1 kHz (81920ns + 81920ns) at 50% duty cycle, to 12.2 kHz at min/max duty
- * cycle (81920 + 10ns or 10ns + 81920ns, respectively).)
- */
-#define IO_PWM_SET_PERIOD   0x21
-
-struct io_pwm_set_period {
-	unsigned int lo;		/* 0..8191 */
-	unsigned int hi;		/* 0..8191 */
-};
-
-/* Only for modes PWM_STANDARD and PWM_FAST.
- * For PWM_STANDARD, set duty cycle of 390 kHz PWM output signal, from
- * 0 (value = 0) to 255/256 (value = 255).
- * For PWM_FAST, set duty cycle of PWM output signal from
- * 0% (value = 0) to 100% (value = 255). Output signal in this mode
- * is a 10ns pulse surrounded by a high or low level depending on duty
- * cycle (except for 0% and 100% which result in a constant output).
- * Resulting output frequency varies from 50 MHz at 50% duty cycle,
- * down to 390 kHz at min/max duty cycle.
- */
-#define IO_PWM_SET_DUTY     0x22
-
-struct io_pwm_set_duty {
-	int duty;		/* 0..255 */
-};
-
-/* Returns information about the latest PWM pulse.
- * lo: Length of the latest low period, in units of 10ns.
- * hi: Length of the latest high period, in units of 10ns.
- * cnt: Time since last detected edge, in units of 10ns.
- *
- * The input source to PWM is decied by IO_PWM_SET_INPUT_SRC.
- *
- * NOTE: All PWM devices is connected to the same input source.
- */
-#define IO_PWM_GET_PERIOD   0x23
-
-struct io_pwm_get_period {
-	unsigned int lo;
-	unsigned int hi;
-	unsigned int cnt;
-};
-
-/* Sets the input source for the PWM input. For the src value see the
- * register description for gio:rw_pwm_in_cfg.
- *
- * NOTE: All PWM devices is connected to the same input source.
- */
-#define IO_PWM_SET_INPUT_SRC   0x24
-struct io_pwm_set_input_src {
-	unsigned int src;	/* 0..7 */
-};
-
-/* Sets the duty cycles in steps of 1/256, 0 = 0%, 255 = 100% duty cycle */
-#define IO_PPWM_SET_DUTY     0x25
-
-struct io_ppwm_set_duty {
-	int duty;		/* 0..255 */
-};
-
-/* Configuraton struct for the IO_PWMCLK_SET_CONFIG ioctl to configure
- * PWM capable gpio pins:
- */
-#define IO_PWMCLK_SETGET_CONFIG 0x26
-struct gpio_pwmclk_conf {
-  unsigned int gpiopin; /* The pin number based on the opened device */
-  unsigned int baseclk; /* The base clock to use, or sw will select one close*/
-  unsigned int low;     /* The number of low periods of the baseclk */
-  unsigned int high;    /* The number of high periods of the baseclk */
-};
-
-/* Examples:
- * To get a symmetric 12 MHz clock without knowing anything about the hardware:
- * baseclk = 12000000, low = 0, high = 0
- * To just get info of current setting:
- * baseclk = 0, low = 0, high = 0, the values will be updated by driver.
- */
-
 #endif