Initial import

1 files changed, 247 insertions, 0 deletions

diff --git a/drivers/usb/phy/phy-rcar-usb.c b/drivers/usb/phy/phy-rcar-usb.c
new file mode 100644
index 000000000..1e09b8377
--- /dev/null
+++ b/drivers/usb/phy/phy-rcar-usb.c
@@ -0,0 +1,247 @@
+/*
+ * Renesas R-Car USB phy driver
+ *
+ * Copyright (C) 2012-2013 Renesas Solutions Corp.
+ * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
+ * Copyright (C) 2013 Cogent Embedded, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/usb/otg.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/platform_data/usb-rcar-phy.h>
+
+/* REGS block */
+#define USBPCTRL0	0x00
+#define USBPCTRL1	0x04
+#define USBST		0x08
+#define USBEH0		0x0C
+#define USBOH0		0x1C
+#define USBCTL0		0x58
+
+/* High-speed signal quality characteristic control registers (R8A7778 only) */
+#define HSQCTL1		0x24
+#define HSQCTL2		0x28
+
+/* USBPCTRL0 */
+#define OVC2		(1 << 10) /* (R8A7779 only)			*/
+				/* Switches the OVC input pin for port 2: */
+				/* 1: USB_OVC2, 0: OVC2			*/
+#define OVC1_VBUS1	(1 << 9) /* Switches the OVC input pin for port 1: */
+				/* 1: USB_OVC1, 0: OVC1/VBUS1		*/
+				/* Function mode: set to 0		*/
+#define OVC0		(1 << 8) /* Switches the OVC input pin for port 0: */
+				/* 1: USB_OVC0 pin, 0: OVC0		*/
+#define OVC2_ACT 	(1 << 6) /* (R8A7779 only)			*/
+				/* Host mode: OVC2 polarity:		*/
+				/* 1: active-high, 0: active-low	*/
+#define PENC		(1 << 4) /* Function mode: output level of PENC1 pin: */
+				/* 1: high, 0: low			*/
+#define OVC0_ACT 	(1 << 3) /* Host mode: OVC0 polarity:		*/
+				/* 1: active-high, 0: active-low	*/
+#define OVC1_ACT	(1 << 1) /* Host mode: OVC1 polarity:		*/
+				/* 1: active-high, 0: active-low	*/
+				/* Function mode: be sure to set to 1	*/
+#define PORT1		(1 << 0) /* Selects port 1 mode:		*/
+				/* 1: function, 0: host			*/
+/* USBPCTRL1 */
+#define PHY_RST		(1 << 2)
+#define PLL_ENB		(1 << 1)
+#define PHY_ENB		(1 << 0)
+
+/* USBST */
+#define ST_ACT		(1 << 31)
+#define ST_PLL		(1 << 30)
+
+struct rcar_usb_phy_priv {
+	struct usb_phy phy;
+	spinlock_t lock;
+
+	void __iomem *reg0;
+	void __iomem *reg1;
+	int counter;
+};
+
+#define usb_phy_to_priv(p) container_of(p, struct rcar_usb_phy_priv, phy)
+
+
+/*
+ * USB initial/install operation.
+ *
+ * This function setup USB phy.
+ * The used value and setting order came from
+ * [USB :: Initial setting] on datasheet.
+ */
+static int rcar_usb_phy_init(struct usb_phy *phy)
+{
+	struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
+	struct device *dev = phy->dev;
+	struct rcar_phy_platform_data *pdata = dev_get_platdata(dev);
+	void __iomem *reg0 = priv->reg0;
+	void __iomem *reg1 = priv->reg1;
+	static const u8 ovcn_act[] = { OVC0_ACT, OVC1_ACT, OVC2_ACT };
+	int i;
+	u32 val;
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->lock, flags);
+	if (priv->counter++ == 0) {
+
+		/*
+		 * USB phy start-up
+		 */
+
+		/* (1) USB-PHY standby release */
+		iowrite32(PHY_ENB, (reg0 + USBPCTRL1));
+
+		/* (2) start USB-PHY internal PLL */
+		iowrite32(PHY_ENB | PLL_ENB, (reg0 + USBPCTRL1));
+
+		/* (3) set USB-PHY in accord with the conditions of usage */
+		if (reg1) {
+			u32 hsqctl1 = pdata->ferrite_bead ? 0x41 : 0;
+			u32 hsqctl2 = pdata->ferrite_bead ? 0x0d : 7;
+
+			iowrite32(hsqctl1, reg1 + HSQCTL1);
+			iowrite32(hsqctl2, reg1 + HSQCTL2);
+		}
+
+		/* (4) USB module status check */
+		for (i = 0; i < 1024; i++) {
+			udelay(10);
+			val = ioread32(reg0 + USBST);
+			if (val == (ST_ACT | ST_PLL))
+				break;
+		}
+
+		if (val != (ST_ACT | ST_PLL)) {
+			dev_err(dev, "USB phy not ready\n");
+			goto phy_init_end;
+		}
+
+		/* (5) USB-PHY reset clear */
+		iowrite32(PHY_ENB | PLL_ENB | PHY_RST, (reg0 + USBPCTRL1));
+
+		/* Board specific port settings */
+		val = 0;
+		if (pdata->port1_func)
+			val |= PORT1;
+		if (pdata->penc1)
+			val |= PENC;
+		for (i = 0; i < 3; i++) {
+			/* OVCn bits follow each other in the right order */
+			if (pdata->ovc_pin[i].select_3_3v)
+				val |= OVC0 << i;
+			/* OVCn_ACT bits are spaced by irregular intervals */
+			if (pdata->ovc_pin[i].active_high)
+				val |= ovcn_act[i];
+		}
+		iowrite32(val, (reg0 + USBPCTRL0));
+
+		/*
+		 * Bus alignment settings
+		 */
+
+		/* (1) EHCI bus alignment (little endian) */
+		iowrite32(0x00000000, (reg0 + USBEH0));
+
+		/* (1) OHCI bus alignment (little endian) */
+		iowrite32(0x00000000, (reg0 + USBOH0));
+	}
+
+phy_init_end:
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	return 0;
+}
+
+static void rcar_usb_phy_shutdown(struct usb_phy *phy)
+{
+	struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
+	void __iomem *reg0 = priv->reg0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->lock, flags);
+
+	if (priv->counter-- == 1)	/* last user */
+		iowrite32(0x00000000, (reg0 + USBPCTRL1));
+
+	spin_unlock_irqrestore(&priv->lock, flags);
+}
+
+static int rcar_usb_phy_probe(struct platform_device *pdev)
+{
+	struct rcar_usb_phy_priv *priv;
+	struct resource *res0, *res1;
+	struct device *dev = &pdev->dev;
+	void __iomem *reg0, *reg1 = NULL;
+	int ret;
+
+	if (!dev_get_platdata(&pdev->dev)) {
+		dev_err(dev, "No platform data\n");
+		return -EINVAL;
+	}
+
+	res0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	reg0 = devm_ioremap_resource(dev, res0);
+	if (IS_ERR(reg0))
+		return PTR_ERR(reg0);
+
+	res1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	reg1 = devm_ioremap_resource(dev, res1);
+	if (IS_ERR(reg1))
+		return PTR_ERR(reg1);
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->reg0		= reg0;
+	priv->reg1		= reg1;
+	priv->counter		= 0;
+	priv->phy.dev		= dev;
+	priv->phy.label		= dev_name(dev);
+	priv->phy.init		= rcar_usb_phy_init;
+	priv->phy.shutdown	= rcar_usb_phy_shutdown;
+	spin_lock_init(&priv->lock);
+
+	ret = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2);
+	if (ret < 0) {
+		dev_err(dev, "usb phy addition error\n");
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, priv);
+
+	return ret;
+}
+
+static int rcar_usb_phy_remove(struct platform_device *pdev)
+{
+	struct rcar_usb_phy_priv *priv = platform_get_drvdata(pdev);
+
+	usb_remove_phy(&priv->phy);
+
+	return 0;
+}
+
+static struct platform_driver rcar_usb_phy_driver = {
+	.driver		= {
+		.name	= "rcar_usb_phy",
+	},
+	.probe		= rcar_usb_phy_probe,
+	.remove		= rcar_usb_phy_remove,
+};
+
+module_platform_driver(rcar_usb_phy_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Renesas R-Car USB phy");
+MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>");