diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display')
48 files changed, 2000 insertions, 179 deletions
diff --git a/Documentation/devicetree/bindings/display/arm,hdlcd.txt b/Documentation/devicetree/bindings/display/arm,hdlcd.txt new file mode 100644 index 000000000..78bc24296 --- /dev/null +++ b/Documentation/devicetree/bindings/display/arm,hdlcd.txt @@ -0,0 +1,79 @@ +ARM HDLCD + +This is a display controller found on several development platforms produced +by ARM Ltd and in more modern of its' Fast Models. The HDLCD is an RGB +streamer that reads the data from a framebuffer and sends it to a single +digital encoder (DVI or HDMI). + +Required properties: + - compatible: "arm,hdlcd" + - reg: Physical base address and length of the controller's registers. + - interrupts: One interrupt used by the display controller to notify the + interrupt controller when any of the interrupt sources programmed in + the interrupt mask register have activated. + - clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. + - clock-names: A list of clock names. For HDLCD it should contain: + - "pxlclk" for the clock feeding the output PLL of the controller. + +Required sub-nodes: + - port: The HDLCD connection to an encoder chip. The connection is modeled + using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt. + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) to be + used for the framebuffer; if not present, the framebuffer may be located + anywhere in memory. + + +Example: + +/ { + ... + + hdlcd@2b000000 { + compatible = "arm,hdlcd"; + reg = <0 0x2b000000 0 0x1000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&oscclk5>; + clock-names = "pxlclk"; + port { + hdlcd_output: endpoint@0 { + remote-endpoint = <&hdmi_enc_input>; + }; + }; + }; + + /* HDMI encoder on I2C bus */ + i2c@7ffa0000 { + .... + hdmi-transmitter@70 { + compatible = "....."; + reg = <0x70>; + port@0 { + hdmi_enc_input: endpoint { + remote-endpoint = <&hdlcd_output>; + }; + + hdmi_enc_output: endpoint { + remote-endpoint = <&hdmi_1_port>; + }; + }; + }; + + }; + + hdmi1: connector@1 { + compatible = "hdmi-connector"; + type = "a"; + port { + hdmi_1_port: endpoint { + remote-endpoint = <&hdmi_enc_output>; + }; + }; + }; + + ... +}; diff --git a/Documentation/devicetree/bindings/display/arm,malidp.txt b/Documentation/devicetree/bindings/display/arm,malidp.txt new file mode 100644 index 000000000..2f7870983 --- /dev/null +++ b/Documentation/devicetree/bindings/display/arm,malidp.txt @@ -0,0 +1,65 @@ +ARM Mali-DP + +The following bindings apply to a family of Display Processors sold as +licensable IP by ARM Ltd. The bindings describe the Mali DP500, DP550 and +DP650 processors that offer multiple composition layers, support for +rotation and scaling output. + +Required properties: + - compatible: should be one of + "arm,mali-dp500" + "arm,mali-dp550" + "arm,mali-dp650" + depending on the particular implementation present in the hardware + - reg: Physical base address and size of the block of registers used by + the processor. + - interrupts: Interrupt list, as defined in ../interrupt-controller/interrupts.txt, + interrupt client nodes. + - interrupt-names: name of the engine inside the processor that will + use the corresponding interrupt. Should be one of "DE" or "SE". + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. It should contain: + - "pclk": for the APB interface clock + - "aclk": for the AXI interface clock + - "mclk": for the main processor clock + - "pxlclk": for the pixel clock feeding the output PLL of the processor. + - arm,malidp-output-port-lines: Array of u8 values describing the number + of output lines per channel (R, G and B). + +Required sub-nodes: + - port: The Mali DP connection to an encoder input port. The connection + is modelled using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for the framebuffer; if not present, the framebuffer may + be located anywhere in memory. + + +Example: + +/ { + ... + + dp0: malidp@6f200000 { + compatible = "arm,mali-dp650"; + reg = <0 0x6f200000 0 0x20000>; + memory-region = <&display_reserved>; + interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>, + <0 168 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "DE", "SE"; + clocks = <&oscclk2>, <&fpgaosc0>, <&fpgaosc1>, <&fpgaosc1>; + clock-names = "pxlclk", "mclk", "aclk", "pclk"; + arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; + port { + dp0_output: endpoint { + remote-endpoint = <&tda998x_2_input>; + }; + }; + }; + + ... +}; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt index 56a961aa5..a5ea451e6 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -35,6 +35,22 @@ Optional properties for HDMI: as an interrupt/status bit in the HDMI controller itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt +Required properties for DPI: +- compatible: Should be "brcm,bcm2835-dpi" +- reg: Physical base address and length of the registers +- clocks: a) core: The core clock the unit runs on + b) pixel: The pixel clock that feeds the pixelvalve +- port: Port node with a single endpoint connecting to the panel + device, as defined in [1] + +Required properties for V3D: +- compatible: Should be "brcm,bcm2835-v3d" +- reg: Physical base address and length of the V3D's registers +- interrupts: The interrupt number + See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt + +[1] Documentation/devicetree/bindings/media/video-interfaces.txt + Example: pixelvalve@7e807000 { compatible = "brcm,bcm2835-pixelvalve2"; @@ -60,6 +76,38 @@ hdmi: hdmi@7e902000 { clock-names = "pixel", "hdmi"; }; +dpi: dpi@7e208000 { + compatible = "brcm,bcm2835-dpi"; + reg = <0x7e208000 0x8c>; + clocks = <&clocks BCM2835_CLOCK_VPU>, + <&clocks BCM2835_CLOCK_DPI>; + clock-names = "core", "pixel"; + #address-cells = <1>; + #size-cells = <0>; + + port { + dpi_out: endpoint@0 { + remote-endpoint = <&panel_in>; + }; + }; +}; + +v3d: v3d@7ec00000 { + compatible = "brcm,bcm2835-v3d"; + reg = <0x7ec00000 0x1000>; + interrupts = <1 10>; +}; + vc4: gpu { compatible = "brcm,bcm2835-vc4"; }; + +panel: panel { + compatible = "ontat,yx700wv03", "simple-panel"; + + port { + panel_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 96c25ee01..6532a59c9 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -1,13 +1,19 @@ -Analog Device ADV7511(W)/13 HDMI Encoders +Analog Device ADV7511(W)/13/33 HDMI Encoders ----------------------------------------- -The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters +The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space conversion, -S/PDIF, CEC and HDCP. +S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while +the others support RGB interface. Required properties: -- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513" +- compatible: Should be one of: + "adi,adv7511" + "adi,adv7511w" + "adi,adv7513" + "adi,adv7533" + - reg: I2C slave address The ADV7511 supports a large number of input data formats that differ by their @@ -32,6 +38,11 @@ The following input format properties are required except in "rgb 1x" and - adi,input-justification: The input bit justification ("left", "evenly", "right"). +The following properties are required for ADV7533: + +- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should + be one of 1, 2, 3 or 4. + Optional properties: - interrupts: Specifier for the ADV7511 interrupt @@ -42,13 +53,18 @@ Optional properties: - adi,embedded-sync: The input uses synchronization signals embedded in the data stream (similar to BT.656). Defaults to separate H/V synchronization signals. +- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing + generator. The chip will rely on the sync signals in the DSI data lanes, + rather than generate its own timings for HDMI output. Required nodes: The ADV7511 has two video ports. Their connections are modelled using the OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. -- Video port 0 for the RGB or YUV input +- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the + remote endpoint phandle should be a reference to a valid mipi_dsi_host device + node. - Video port 1 for the HDMI output diff --git a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt new file mode 100644 index 000000000..4a0f4f768 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt @@ -0,0 +1,53 @@ +Analogix Display Port bridge bindings + +Required properties for dp-controller: + -compatible: + platform specific such as: + * "samsung,exynos5-dp" + * "rockchip,rk3288-dp" + * "rockchip,rk3399-edp" + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -clocks: + from common clock binding: handle to dp clock. + -clock-names: + from common clock binding: Shall be "dp". + -interrupt-parent: + phandle to Interrupt combiner node. + -phys: + from general PHY binding: the phandle for the PHY device. + -phy-names: + from general PHY binding: Should be "dp". + +Optional properties for dp-controller: + -force-hpd: + Indicate driver need force hpd when hpd detect failed, this + is used for some eDP screen which don't have hpd signal. + -hpd-gpios: + Hotplug detect GPIO. + Indicates which GPIO should be used for hotplug detection + -port@[X]: SoC specific port nodes with endpoint definitions as defined + in Documentation/devicetree/bindings/media/video-interfaces.txt, + please refer to the SoC specific binding document: + * Documentation/devicetree/bindings/display/exynos/exynos_dp.txt + * Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt +------------------------------------------------------------------------------- + +Example: + + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + clocks = <&clock 342>; + clock-names = "dp"; + + phys = <&dp_phy>; + phy-names = "dp"; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt new file mode 100644 index 000000000..56a3e68cc --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt @@ -0,0 +1,35 @@ +sii902x HDMI bridge bindings + +Required properties: + - compatible: "sil,sii9022" + - reg: i2c address of the bridge + +Optional properties: + - interrupts-extended or interrupt-parent + interrupts: describe + the interrupt line used to inform the host about hotplug events. + - reset-gpios: OF device-tree gpio specification for RST_N pin. + +Optional subnodes: + - video input: this subnode can contain a video input port node + to connect the bridge to a display controller output (See this + documentation [1]). + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + hdmi-bridge@39 { + compatible = "sil,sii9022"; + reg = <0x39>; + reset-gpios = <&pioA 1 0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + bridge_in: endpoint { + remote-endpoint = <&dc_out>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt new file mode 100644 index 000000000..e3f6aa6a2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt @@ -0,0 +1,53 @@ +Toshiba TC358767 eDP bridge bindings + +Required properties: + - compatible: "toshiba,tc358767" + - reg: i2c address of the bridge, 0x68 or 0x0f, depending on bootstrap pins + - clock-names: should be "ref" + - clocks: OF device-tree clock specification for refclk input. The reference + clock rate must be 13 MHz, 19.2 MHz, 26 MHz, or 38.4 MHz. + +Optional properties: + - shutdown-gpios: OF device-tree gpio specification for SD pin + (active high shutdown input) + - reset-gpios: OF device-tree gpio specification for RSTX pin + (active low system reset) + - ports: the ports node can contain video interface port nodes to connect + to a DPI/DSI source and to an eDP/DP sink according to [1][2]: + - port@0: DSI input port + - port@1: DPI input port + - port@2: eDP/DP output port + +[1]: Documentation/devicetree/bindings/graph.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + edp-bridge@68 { + compatible = "toshiba,tc358767"; + reg = <0x68>; + shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>; + clock-names = "ref"; + clocks = <&edp_refclk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + bridge_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + port@2 { + reg = <2>; + + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt index d685be898..e9c65746e 100644 --- a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt +++ b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt @@ -1,7 +1,7 @@ * Currus Logic CLPS711X Framebuffer Required properties: -- compatible: Shall contain "cirrus,clps711x-fb". +- compatible: Shall contain "cirrus,ep7209-fb". - reg : Physical base address and length of the controller's registers + location and size of the framebuffer memory. - clocks : phandle + clock specifier pair of the FB reference clock. @@ -18,7 +18,7 @@ Optional properties: Example: fb: fb@800002c0 { - compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb"; + compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb"; reg = <0x800002c0 0xd44>, <0x60000000 0xc000>; clocks = <&clks 2>; lcd-supply = <®5v0>; diff --git a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt index acd5668b1..508aee461 100644 --- a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt +++ b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt @@ -8,6 +8,7 @@ Required properties: Optional properties: - label: a symbolic name for the connector - hpd-gpios: HPD GPIO number +- ddc-i2c-bus: phandle link to the I2C controller used for DDC EDID probing Required nodes: - Video port for HDMI input diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt index 377afbf51..c9fd7b380 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -5,7 +5,8 @@ Exynos series of SoCs which transfers the image data from a video memory buffer to an external LCD interface. Required properties: -- compatible: value should be "samsung,exynos5433-decon"; +- compatible: value should be one of: + "samsung,exynos5433-decon", "samsung,exynos5433-decon-tv"; - reg: physical base address and length of the DECON registers set. - interrupts: should contain a list of all DECON IP block interrupts in the order: VSYNC, LCD_SYSTEM. The interrupt specifier format @@ -16,7 +17,7 @@ Required properties: - clocks: must include clock specifiers corresponding to entries in the clock-names property. - clock-names: list of clock names sorted in the same order as the clocks - property. Must contain "aclk_decon", "aclk_smmu_decon0x", + property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", "sclk_decon_eclk" - ports: contains a port which is connected to mic node. address-cells and diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt index fe4a7a2de..ade5d8eeb 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt @@ -1,20 +1,3 @@ -Device-Tree bindings for Samsung Exynos Embedded DisplayPort Transmitter(eDP) - -DisplayPort is industry standard to accommodate the growing board adoption -of digital display technology within the PC and CE industries. -It consolidates the internal and external connection methods to reduce device -complexity and cost. It also supports necessary features for important cross -industry applications and provides performance scalability to enable the next -generation of displays that feature higher color depths, refresh rates, and -display resolutions. - -eDP (embedded display port) device is compliant with Embedded DisplayPort -standard as follows, -- DisplayPort standard 1.1a for Exynos5250 and Exynos5260. -- DisplayPort standard 1.3 for Exynos5422s and Exynos5800. - -eDP resides between FIMD and panel or FIMD and bridge such as LVDS. - The Exynos display port interface should be configured based on the type of panel connected to it. @@ -48,26 +31,6 @@ Required properties for dp-controller: from general PHY binding: the phandle for the PHY device. -phy-names: from general PHY binding: Should be "dp". - -samsung,color-space: - input video data format. - COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 - -samsung,dynamic-range: - dynamic range for input video data. - VESA = 0, CEA = 1 - -samsung,ycbcr-coeff: - YCbCr co-efficients for input video. - COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 - -samsung,color-depth: - number of bits per colour component. - COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 - -samsung,link-rate: - link rate supported by the panel. - LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A - -samsung,lane-count: - number of lanes supported by the panel. - LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 - - display-timings: timings for the connected panel as described by - Documentation/devicetree/bindings/display/display-timing.txt Optional properties for dp-controller: -interlaced: @@ -83,17 +46,31 @@ Optional properties for dp-controller: Hotplug detect GPIO. Indicates which GPIO should be used for hotplug detection -Video interfaces: - Device node can contain video interface port nodes according to [1]. - The following are properties specific to those nodes: - - endpoint node connected to bridge or panel node: - - remote-endpoint: specifies the endpoint in panel or bridge node. - This node is required in all kinds of exynos dp - to represent the connection between dp and bridge - or dp and panel. - -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + -video interfaces: Device node can contain video interface port + nodes according to [1]. + - display-timings: timings for the connected panel as described by + Documentation/devicetree/bindings/display/panel/display-timing.txt + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/display/bridge/analogix_dp.txt + -phys (required) + -phy-names (required) + -hpd-gpios (optional) + force-hpd (optional) + +Deprecated properties for DisplayPort: +-interlaced: deprecated prop that can parsed from drm_display_mode. +-vsync-active-high: deprecated prop that can parsed from drm_display_mode. +-hsync-active-high: deprecated prop that can parsed from drm_display_mode. +-samsung,ycbcr-coeff: deprecated prop that can parsed from drm_display_mode. +-samsung,dynamic-range: deprecated prop that can parsed from drm_display_mode. +-samsung,color-space: deprecated prop that can parsed from drm_display_info. +-samsung,color-depth: deprecated prop that can parsed from drm_display_info. +-samsung,link-rate: deprecated prop that can reading from monitor by dpcd method. +-samsung,lane-count: deprecated prop that can reading from monitor by dpcd method. +-samsung,hpd-gpio: deprecated name for hpd-gpios. + +------------------------------------------------------------------------------- Example: @@ -112,13 +89,6 @@ SOC specific portion: Board Specific portion: dp-controller { - samsung,color-space = <0>; - samsung,dynamic-range = <0>; - samsung,ycbcr-coeff = <0>; - samsung,color-depth = <1>; - samsung,link-rate = <0x0a>; - samsung,lane-count = <4>; - display-timings { native-mode = <&lcd_timing>; lcd_timing: 1366x768 { @@ -135,18 +105,9 @@ Board Specific portion: }; ports { - port { + port@0 { dp_out: endpoint { - remote-endpoint = <&dp_in>; - }; - }; - }; - - panel { - ... - port { - dp_in: endpoint { - remote-endpoint = <&dp_out>; + remote-endpoint = <&bridge_in>; }; }; }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index 0e6f0c024..a78265993 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -6,6 +6,7 @@ Required properties: "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */ "samsung,exynos4415-mipi-dsi" /* for Exynos4415 SoC */ "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */ + "samsung,exynos5422-mipi-dsi" /* for Exynos5422/5800 SoCs */ "samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */ - reg: physical base address and length of the registers set for the device - interrupts: should contain DSI interrupt @@ -40,7 +41,7 @@ Video interfaces: endpoint node connected from mic node (reg = 0): - remote-endpoint: specifies the endpoint in mic node. This node is required for Exynos5433 mipi dsi. So mic can access to panel node - thoughout this dsi node. + throughout this dsi node. endpoint node connected to panel node (reg = 1): - remote-endpoint: specifies the endpoint in panel node. This node is required in all kinds of exynos mipi dsi to represent diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt index d474f59be..a2ec4c1c9 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt @@ -5,6 +5,7 @@ Required properties: 1) "samsung,exynos4210-hdmi" 2) "samsung,exynos4212-hdmi" 3) "samsung,exynos5420-hdmi" + 4) "samsung,exynos5433-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -12,6 +13,11 @@ Required properties: a) phandle of the gpio controller node. b) pin number within the gpio controller. c) optional flags and pull up/down. +- ddc: phandle to the hdmi ddc node +- phy: phandle to the hdmi phy node +- samsung,syscon-phandle: phandle for system controller node for PMU. + +Required properties for Exynos 4210, 4212, 5420 and 5433: - clocks: list of clock IDs from SoC clock driver. a) hdmi: Gate of HDMI IP bus clock. b) sclk_hdmi: Gate of HDMI special clock. @@ -25,9 +31,24 @@ Required properties: sclk_pixel. - clock-names: aliases as per driver requirements for above clock IDs: "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi". -- ddc: phandle to the hdmi ddc node -- phy: phandle to the hdmi phy node -- samsung,syscon-phandle: phandle for system controller node for PMU. + +Required properties for Exynos 5433: +- clocks: list of clock specifiers according to common clock bindings. + a) hdmi_pclk: Gate of HDMI IP APB bus. + b) hdmi_i_pclk: Gate of HDMI-PHY IP APB bus. + d) i_tmds_clk: Gate of HDMI TMDS clock. + e) i_pixel_clk: Gate of HDMI pixel clock. + f) i_spdif_clk: Gate of HDMI SPDIF clock. + g) oscclk: Oscillator clock, used as parent of following *_user clocks + in case HDMI-PHY is not operational. + h) tmds_clko: TMDS clock generated by HDMI-PHY. + i) tmds_clko_user: MUX used to switch between oscclk and tmds_clko, + respectively if HDMI-PHY is off and operational. + j) pixel_clko: Pixel clock generated by HDMI-PHY. + k) pixel_clko_user: MUX used to switch between oscclk and pixel_clko, + respectively if HDMI-PHY is off and operational. +- clock-names: aliases for above clock specfiers. +- samsung,sysreg: handle to syscon used to control the system registers. Example: diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt index 27c3ce0db..c7c6b9af8 100644 --- a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt +++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt @@ -12,7 +12,8 @@ Required properties: "samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ "samsung,exynos4415-fimd"; /* for Exynos4415 SoC */ - "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */ + "samsung,exynos5250-fimd"; /* for Exynos5250 SoCs */ + "samsung,exynos5420-fimd"; /* for Exynos5420/5422/5800 SoCs */ - reg: physical base address and length of the FIMD registers set. diff --git a/Documentation/devicetree/bindings/display/fsl,dcu.txt b/Documentation/devicetree/bindings/display/fsl,dcu.txt index ebf1be9ae..63ec2a624 100644 --- a/Documentation/devicetree/bindings/display/fsl,dcu.txt +++ b/Documentation/devicetree/bindings/display/fsl,dcu.txt @@ -6,17 +6,29 @@ Required properties: * "fsl,vf610-dcu". - reg: Address and length of the register set for dcu. -- clocks: From common clock binding: handle to dcu clock. -- clock-names: From common clock binding: Shall be "dcu". +- clocks: Handle to "dcu" and "pix" clock (in the order below) + This can be the same clock (e.g. LS1021a) + See ../clocks/clock-bindings.txt for details. +- clock-names: Should be "dcu" and "pix" + See ../clocks/clock-bindings.txt for details. - big-endian Boolean property, LS1021A DCU registers are big-endian. -- fsl,panel: The phandle to panel node. +- port Video port for the panel output + +Optional properties: +- fsl,tcon: The phandle to the timing controller node. Examples: dcu: dcu@2ce0000 { compatible = "fsl,ls1021a-dcu"; reg = <0x0 0x2ce0000 0x0 0x10000>; - clocks = <&platform_clk 0>; - clock-names = "dcu"; + clocks = <&platform_clk 0>, <&platform_clk 0>; + clock-names = "dcu", "pix"; big-endian; - fsl,panel = <&panel>; + fsl,tcon = <&tcon>; + + port { + dcu_out: endpoint { + remote-endpoint = <&panel_out>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/display/fsl,tcon.txt b/Documentation/devicetree/bindings/display/fsl,tcon.txt new file mode 100644 index 000000000..6fa4ab668 --- /dev/null +++ b/Documentation/devicetree/bindings/display/fsl,tcon.txt @@ -0,0 +1,18 @@ +Device Tree bindings for Freescale TCON Driver + +Required properties: +- compatible: Should be one of + * "fsl,vf610-tcon". + +- reg: Address and length of the register set for tcon. +- clocks: From common clock binding: handle to tcon ipg clock. +- clock-names: From common clock binding: Shall be "ipg". + +Examples: +timing-controller@4003d000 { + compatible = "fsl,vf610-tcon"; + reg = <0x4003d000 0x1000>; + clocks = <&clks VF610_CLK_TCON0>; + clock-names = "ipg"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt new file mode 100644 index 000000000..d270bfe4e --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt @@ -0,0 +1,72 @@ +Device-Tree bindings for DesignWare DSI Host Controller v1.20a driver + +A DSI Host Controller resides in the middle of display controller and external +HDMI converter or panel. + +Required properties: +- compatible: value should be "hisilicon,hi6220-dsi". +- reg: physical base address and length of dsi controller's registers. +- clocks: contains APB clock phandle + clock-specifier pair. +- clock-names: should be "pclk". +- ports: contains DSI controller input and output sub port. + The input port connects to ADE output port with the reg value "0". + The output port with the reg value "1", it could connect to panel or + any other bridge endpoints. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +A example of HiKey board hi6220 SoC and board specific DT entry: +Example: + +SoC specific: + dsi: dsi@f4107800 { + compatible = "hisilicon,hi6220-dsi"; + reg = <0x0 0xf4107800 0x0 0x100>; + clocks = <&media_ctrl HI6220_DSI_PCLK>; + clock-names = "pclk"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 0 for input port */ + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <&ade_out>; + }; + }; + }; + }; + + +Board specific: + &dsi { + status = "ok"; + + ports { + /* 1 for output port */ + port@1 { + reg = <1>; + + dsi_out0: endpoint@0 { + remote-endpoint = <&adv7533_in>; + }; + }; + }; + }; + + &i2c2 { + ... + + adv7533: adv7533@39 { + ... + + port { + adv7533_in: endpoint { + remote-endpoint = <&dsi_out0>; + }; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt new file mode 100644 index 000000000..38dc9d60e --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt @@ -0,0 +1,64 @@ +Device-Tree bindings for hisilicon ADE display controller driver + +ADE (Advanced Display Engine) is the display controller which grab image +data from memory, do composition, do post image processing, generate RGB +timing stream and transfer to DSI. + +Required properties: +- compatible: value should be "hisilicon,hi6220-ade". +- reg: physical base address and length of the ADE controller's registers. +- hisilicon,noc-syscon: ADE NOC QoS syscon. +- resets: The ADE reset controller node. +- interrupt: the ldi vblank interrupt number used. +- clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. +- clock-names: should contain: + "clk_ade_core" for the ADE core clock. + "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with + jpeg codec. + "clk_ade_pix" for the ADE pixel clok. +- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks' + phandle + clock-specifier pairs. +- assigned-clock-rates: clock rates, one for each entry in assigned-clocks. + The rate of "clk_ade_core" could be "360000000" or "180000000"; + The rate of "clk_codec_jpeg" could be or less than "1440000000". + These rate values could be configured according to performance and power + consumption. +- port: the output port. This contains one endpoint subnode, with its + remote-endpoint set to the phandle of the connected DSI input endpoint. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +Optional properties: +- dma-coherent: Present if dma operations are coherent. + + +A example of HiKey board hi6220 SoC specific DT entry: +Example: + + ade: ade@f4100000 { + compatible = "hisilicon,hi6220-ade"; + reg = <0x0 0xf4100000 0x0 0x7800>; + reg-names = "ade_base"; + hisilicon,noc-syscon = <&medianoc_ade>; + resets = <&media_ctrl MEDIA_ADE>; + interrupts = <0 115 4>; /* ldi interrupt */ + + clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>, + <&media_ctrl HI6220_ADE_PIX_SRC>; + /*clock name*/ + clock-names = "clk_ade_core", + "clk_codec_jpeg", + "clk_ade_pix"; + + assigned-clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>; + assigned-clock-rates = <360000000>, <288000000>; + dma-coherent; + + port { + ade_out: endpoint { + remote-endpoint = <&dsi_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt index 0a175d991..a407462c8 100644 --- a/Documentation/devicetree/bindings/display/imx/ldb.txt +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -62,6 +62,7 @@ Required properties: display-timings are used instead. Optional properties (required if display-timings are used): + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - display-timings : A node that describes the display timings as defined in Documentation/devicetree/bindings/display/display-timing.txt. - fsl,data-mapping : should be "spwg" or "jeida" diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt new file mode 100644 index 000000000..db6e77edb --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt @@ -0,0 +1,203 @@ +Mediatek display subsystem +========================== + +The Mediatek display subsystem consists of various DISP function blocks in the +MMSYS register space. The connections between them can be configured by output +and input selectors in the MMSYS_CONFIG register space. Pixel clock and start +of frame signal are distributed to the other function blocks by a DISP_MUTEX +function block. + +All DISP device tree nodes must be siblings to the central MMSYS_CONFIG node. +For a description of the MMSYS_CONFIG binding, see +Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt. + +DISP function blocks +==================== + +A display stream starts at a source function block that reads pixel data from +memory and ends with a sink function block that drives pixels on a display +interface, or writes pixels back to memory. All DISP function blocks have +their own register space, interrupt, and clock gate. The blocks that can +access memory additionally have to list the IOMMU and local arbiter they are +connected to. + +For a description of the display interface sink function blocks, see +Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt and +Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt. + +Required properties (all function blocks): +- compatible: "mediatek,<chip>-disp-<function>", one of + "mediatek,<chip>-disp-ovl" - overlay (4 layers, blending, csc) + "mediatek,<chip>-disp-rdma" - read DMA / line buffer + "mediatek,<chip>-disp-wdma" - write DMA + "mediatek,<chip>-disp-color" - color processor + "mediatek,<chip>-disp-aal" - adaptive ambient light controller + "mediatek,<chip>-disp-gamma" - gamma correction + "mediatek,<chip>-disp-merge" - merge streams from two RDMA sources + "mediatek,<chip>-disp-split" - split stream to two encoders + "mediatek,<chip>-disp-ufoe" - data compression engine + "mediatek,<chip>-dsi" - DSI controller, see mediatek,dsi.txt + "mediatek,<chip>-dpi" - DPI controller, see mediatek,dpi.txt + "mediatek,<chip>-disp-mutex" - display mutex + "mediatek,<chip>-disp-od" - overdrive +- reg: Physical base address and length of the function block register space +- interrupts: The interrupt signal from the function block (required, except for + merge and split function blocks). +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. + For most function blocks this is just a single clock input. Only the DSI and + DPI controller nodes have multiple clock inputs. These are documented in + mediatek,dsi.txt and mediatek,dpi.txt, respectively. + +Required properties (DMA function blocks): +- compatible: Should be one of + "mediatek,<chip>-disp-ovl" + "mediatek,<chip>-disp-rdma" + "mediatek,<chip>-disp-wdma" +- larb: Should contain a phandle pointing to the local arbiter device as defined + in Documentation/devicetree/bindings/soc/mediatek/mediatek,smi-larb.txt +- iommus: Should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. + +Examples: + +mmsys: clock-controller@14000000 { + compatible = "mediatek,mt8173-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + #clock-cells = <1>; +}; + +ovl0: ovl@1400c000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400c000 0 0x1000>; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL0>; + iommus = <&iommu M4U_PORT_DISP_OVL0>; + mediatek,larb = <&larb0>; +}; + +ovl1: ovl@1400d000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400d000 0 0x1000>; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL1>; + iommus = <&iommu M4U_PORT_DISP_OVL1>; + mediatek,larb = <&larb4>; +}; + +rdma0: rdma@1400e000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400e000 0 0x1000>; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA0>; + iommus = <&iommu M4U_PORT_DISP_RDMA0>; + mediatek,larb = <&larb0>; +}; + +rdma1: rdma@1400f000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400f000 0 0x1000>; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA1>; + iommus = <&iommu M4U_PORT_DISP_RDMA1>; + mediatek,larb = <&larb4>; +}; + +rdma2: rdma@14010000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x14010000 0 0x1000>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA2>; + iommus = <&iommu M4U_PORT_DISP_RDMA2>; + mediatek,larb = <&larb4>; +}; + +wdma0: wdma@14011000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14011000 0 0x1000>; + interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA0>; + iommus = <&iommu M4U_PORT_DISP_WDMA0>; + mediatek,larb = <&larb0>; +}; + +wdma1: wdma@14012000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14012000 0 0x1000>; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA1>; + iommus = <&iommu M4U_PORT_DISP_WDMA1>; + mediatek,larb = <&larb4>; +}; + +color0: color@14013000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14013000 0 0x1000>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR0>; +}; + +color1: color@14014000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14014000 0 0x1000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR1>; +}; + +aal@14015000 { + compatible = "mediatek,mt8173-disp-aal"; + reg = <0 0x14015000 0 0x1000>; + interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_AAL>; +}; + +gamma@14016000 { + compatible = "mediatek,mt8173-disp-gamma"; + reg = <0 0x14016000 0 0x1000>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_GAMMA>; +}; + +ufoe@1401a000 { + compatible = "mediatek,mt8173-disp-ufoe"; + reg = <0 0x1401a000 0 0x1000>; + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_UFOE>; +}; + +dsi0: dsi@1401b000 { + /* See mediatek,dsi.txt for details */ +}; + +dpi0: dpi@1401d000 { + /* See mediatek,dpi.txt for details */ +}; + +mutex: mutex@14020000 { + compatible = "mediatek,mt8173-disp-mutex"; + reg = <0 0x14020000 0 0x1000>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MUTEX_32K>; +}; + +od@14023000 { + compatible = "mediatek,mt8173-disp-od"; + reg = <0 0x14023000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OD>; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt new file mode 100644 index 000000000..b6a7e7397 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt @@ -0,0 +1,35 @@ +Mediatek DPI Device +=================== + +The Mediatek DPI function block is a sink of the display subsystem and +provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel +output bus. + +Required properties: +- compatible: "mediatek,<chip>-dpi" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "engine", and "pll" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached HDMI or LVDS encoder chip. + +Example: + +dpi0: dpi@1401d000 { + compatible = "mediatek,mt8173-dpi"; + reg = <0 0x1401d000 0 0x1000>; + interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_DPI_PIXEL>, + <&mmsys CLK_MM_DPI_ENGINE>, + <&apmixedsys CLK_APMIXED_TVDPLL>; + clock-names = "pixel", "engine", "pll"; + + port { + dpi0_out: endpoint { + remote-endpoint = <&hdmi0_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt new file mode 100644 index 000000000..2b1585a34 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt @@ -0,0 +1,60 @@ +Mediatek DSI Device +=================== + +The Mediatek DSI function block is a sink of the display subsystem and can +drive up to 4-lane MIPI DSI output. Two DSIs can be synchronized for dual- +channel output. + +Required properties: +- compatible: "mediatek,<chip>-dsi" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "engine", "digital", and "hs" +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached DSI panel or DSI-to-eDP encoder chip. + +MIPI TX Configuration Module +============================ + +The MIPI TX configuration module controls the MIPI D-PHY. + +Required properties: +- compatible: "mediatek,<chip>-mipi-tx" +- reg: Physical base address and length of the controller's registers +- clocks: PLL reference clock +- clock-output-names: name of the output clock line to the DSI encoder +- #clock-cells: must be <0>; +- #phy-cells: must be <0>. + +Example: + +mipi_tx0: mipi-dphy@10215000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0 0x10215000 0 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx0_pll"; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +dsi0: dsi@1401b000 { + compatible = "mediatek,mt8173-dsi"; + reg = <0 0x1401b000 0 0x1000>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys MM_DSI0_ENGINE>, <&mmsys MM_DSI0_DIGITAL>, + <&mipi_tx0>; + clock-names = "engine", "digital", "hs"; + phys = <&mipi_tx0>; + phy-names = "dphy"; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt new file mode 100644 index 000000000..7b124242b --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt @@ -0,0 +1,148 @@ +Mediatek HDMI Encoder +===================== + +The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from +its parallel input. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi". +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "pll", "bclk", and "spdif". +- phys: phandle link to the HDMI PHY node. + See Documentation/devicetree/bindings/phy/phy-bindings.txt for details. +- phy-names: must contain "hdmi" +- mediatek,syscon-hdmi: phandle link and register offset to the system + configuration registers. For mt8173 this must be offset 0x900 into the + MMSYS_CONFIG region: <&mmsys 0x900>. +- ports: A node containing input and output port nodes with endpoint + definitions as documented in Documentation/devicetree/bindings/graph.txt. +- port@0: The input port in the ports node should be connected to a DPI output + port. +- port@1: The output port in the ports node should be connected to the input + port of a connector node that contains a ddc-i2c-bus property, or to the + input port of an attached bridge chip, such as a SlimPort transmitter. + +HDMI CEC +======== + +The HDMI CEC controller handles hotplug detection and CEC communication. + +Required properties: +- compatible: Should be "mediatek,<chip>-cec" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clock + +HDMI DDC +======== + +The HDMI DDC i2c controller is used to interface with the HDMI DDC pins. +The Mediatek's I2C controller is used to interface with I2C devices. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi-ddc" +- reg: Physical base address and length of the controller's registers +- clocks: device clock +- clock-names: Should be "ddc-i2c". + +HDMI PHY +======== + +The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel +output and drives the HDMI pads. + +Required properties: +- compatible: "mediatek,<chip>-hdmi-phy" +- reg: Physical base address and length of the module's registers +- clocks: PLL reference clock +- clock-names: must contain "pll_ref" +- clock-output-names: must be "hdmitx_dig_cts" on mt8173 +- #phy-cells: must be <0> +- #clock-cells: must be <0> + +Optional properties: +- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa +- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c + +Example: + +cec: cec@10013000 { + compatible = "mediatek,mt8173-cec"; + reg = <0 0x10013000 0 0xbc>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_CEC>; +}; + +hdmi_phy: hdmi-phy@10209100 { + compatible = "mediatek,mt8173-hdmi-phy"; + reg = <0 0x10209100 0 0x24>; + clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>; + clock-names = "pll_ref"; + clock-output-names = "hdmitx_dig_cts"; + mediatek,ibias = <0xa>; + mediatek,ibias_up = <0x1c>; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +hdmi_ddc0: i2c@11012000 { + compatible = "mediatek,mt8173-hdmi-ddc"; + reg = <0 0x11012000 0 0x1c>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_I2C5>; + clock-names = "ddc-i2c"; +}; + +hdmi0: hdmi@14025000 { + compatible = "mediatek,mt8173-hdmi"; + reg = <0 0x14025000 0 0x400>; + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_HDMI_PIXEL>, + <&mmsys CLK_MM_HDMI_PLLCK>, + <&mmsys CLK_MM_HDMI_AUDIO>, + <&mmsys CLK_MM_HDMI_SPDIF>; + clock-names = "pixel", "pll", "bclk", "spdif"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pin>; + phys = <&hdmi_phy>; + phy-names = "hdmi"; + mediatek,syscon-hdmi = <&mmsys 0x900>; + assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>; + assigned-clock-parents = <&hdmi_phy>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi0_in: endpoint { + remote-endpoint = <&dpi0_out>; + }; + }; + + port@1 { + reg = <1>; + + hdmi0_out: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + }; +}; + +connector { + compatible = "hdmi-connector"; + type = "a"; + ddc-i2c-bus = <&hdmiddc0>; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index e7423bea1..6b1cab17f 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -11,8 +11,7 @@ Required properties: be 0 or 1, since we have 2 DSI controllers at most for now. - interrupts: The interrupt signal from the DSI block. - power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clocks: Phandles to device clocks. - clock-names: the following clocks are required: * "mdp_core_clk" * "iface_clk" @@ -23,16 +22,21 @@ Required properties: * "core_clk" For DSIv2, we need an additional clock: * "src_clk" +- assigned-clocks: Parents of "byte_clk" and "pixel_clk" for the given platform. +- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided + by a DSI PHY block. See [1] for details on clock bindings. - vdd-supply: phandle to vdd regulator device node - vddio-supply: phandle to vdd-io regulator device node - vdda-supply: phandle to vdda regulator device node -- qcom,dsi-phy: phandle to DSI PHY device node +- phys: phandle to DSI PHY device node +- phy-names: the name of the corresponding PHY device - syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) +- ports: Contains 2 DSI controller ports as child nodes. Each port contains + an endpoint subnode as defined in [2] and [3]. Optional properties: - panel@0: Node of panel connected to this DSI controller. - See files in Documentation/devicetree/bindings/display/panel/ for each supported - panel. + See files in [4] for each supported panel. - qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is driving a panel which needs 2 DSI links. - qcom,master-dsi: Boolean value indicating if the DSI controller is driving @@ -44,9 +48,38 @@ Optional properties: - pinctrl-names: the pin control state names; should contain "default" - pinctrl-0: the default pinctrl state (active) - pinctrl-n: the "sleep" pinctrl state -- port: DSI controller output port. This contains one endpoint subnode, with its - remote-endpoint set to the phandle of the connected panel's endpoint. - See Documentation/devicetree/bindings/graph.txt for device graph info. +- ports: contains DSI controller input and output ports as children, each + containing one endpoint subnode. + + DSI Endpoint properties: + - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's + input endpoint. For port@1, set to the MDP interface output. See [2] for + device graph info. + + - data-lanes: this describes how the physical DSI data lanes are mapped + to the logical lanes on the given platform. The value contained in + index n describes what physical lane is mapped to the logical lane n + (DATAn, where n lies between 0 and 3). The clock lane position is fixed + and can't be changed. Hence, they aren't a part of the DT bindings. See + [3] for more info on the data-lanes property. + + For example: + + data-lanes = <3 0 1 2>; + + The above mapping describes that the logical data lane DATA0 is mapped to + the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 + to phys DATA1 and logic DATA3 to phys DATA2. + + There are only a limited number of physical to logical mappings possible: + <0 1 2 3> + <1 2 3 0> + <2 3 0 1> + <3 0 1 2> + <0 3 2 1> + <1 0 3 2> + <2 1 0 3> + <3 2 1 0> DSI PHY: Required properties: @@ -61,11 +94,12 @@ Required properties: * "dsi_pll" * "dsi_phy" * "dsi_phy_regulator" +- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating + 2 clocks: A byte clock (index 0), and a pixel clock (index 1). - qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should be 0 or 1, since we have 2 DSI PHYs at most for now. - power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clocks: Phandles to device clocks. See [1] for details on clock bindings. - clock-names: the following clocks are required: * "iface_clk" - vddio-supply: phandle to vdd-io regulator device node @@ -74,11 +108,16 @@ Optional properties: - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY regulator is wanted. +[1] Documentation/devicetree/bindings/clocks/clock-bindings.txt +[2] Documentation/devicetree/bindings/graph.txt +[3] Documentation/devicetree/bindings/media/video-interfaces.txt +[4] Documentation/devicetree/bindings/display/panel/ + Example: - mdss_dsi0: qcom,mdss_dsi@fd922800 { + dsi0: dsi@fd922800 { compatible = "qcom,mdss-dsi-ctrl"; qcom,dsi-host-index = <0>; - interrupt-parent = <&mdss_mdp>; + interrupt-parent = <&mdp>; interrupts = <4 0>; reg-names = "dsi_ctrl"; reg = <0xfd922800 0x200>; @@ -99,19 +138,48 @@ Example: <&mmcc MDSS_AHB_CLK>, <&mmcc MDSS_MDP_CLK>, <&mmcc MDSS_PCLK0_CLK>; + + assigned-clocks = + <&mmcc BYTE0_CLK_SRC>, + <&mmcc PCLK0_CLK_SRC>; + assigned-clock-parents = + <&dsi_phy0 0>, + <&dsi_phy0 1>; + vdda-supply = <&pma8084_l2>; vdd-supply = <&pma8084_l22>; vddio-supply = <&pma8084_l12>; - qcom,dsi-phy = <&mdss_dsi_phy0>; + phys = <&dsi_phy0>; + phy-names ="dsi-phy"; qcom,dual-dsi-mode; qcom,master-dsi; qcom,sync-dual-dsi; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&mdss_dsi_active>; - pinctrl-1 = <&mdss_dsi_suspend>; + pinctrl-0 = <&dsi_active>; + pinctrl-1 = <&dsi_suspend>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; panel: panel@0 { compatible = "sharp,lq101r1sx01"; @@ -127,15 +195,9 @@ Example: }; }; }; - - port { - dsi0_out: endpoint { - remote-endpoint = <&panel_in>; - }; - }; }; - mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 { + dsi_phy0: dsi-phy@fd922a00 { compatible = "qcom,dsi-phy-28nm-hpm"; qcom,dsi-phy-index = <0>; reg-names = @@ -147,6 +209,7 @@ Example: <0xfd922d80 0x7b>; clock-names = "iface_clk"; clocks = <&mmcc MDSS_AHB_CLK>; + #clock-cells = <1>; vddio-supply = <&pma8084_l12>; qcom,dsi-phy-regulator-ldo-mode; diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt index 379ee2ea9..b63f614e0 100644 --- a/Documentation/devicetree/bindings/display/msm/hdmi.txt +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -11,6 +11,7 @@ Required properties: - reg: Physical base address and length of the controller's registers - reg-names: "core_physical" - interrupts: The interrupt signal from the hdmi block. +- power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: device clocks See ../clocks/clock-bindings.txt for details. - qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin @@ -18,6 +19,8 @@ Required properties: - qcom,hdmi-tx-hpd-gpio: hpd pin - core-vdda-supply: phandle to supply regulator - hdmi-mux-supply: phandle to mux regulator +- phys: the phandle for the HDMI PHY device +- phy-names: the name of the corresponding PHY device Optional properties: - qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin @@ -27,15 +30,38 @@ Optional properties: - pinctrl-0: the default pinctrl state (active) - pinctrl-1: the "sleep" pinctrl state +HDMI PHY: +Required properties: +- compatible: Could be the following + * "qcom,hdmi-phy-8660" + * "qcom,hdmi-phy-8960" + * "qcom,hdmi-phy-8974" + * "qcom,hdmi-phy-8084" + * "qcom,hdmi-phy-8996" +- #phy-cells: Number of cells in a PHY specifier; Should be 0. +- reg: Physical base address and length of the registers of the PHY sub blocks. +- reg-names: The names of register regions. The following regions are required: + * "hdmi_phy" + * "hdmi_pll" + For HDMI PHY on msm8996, these additional register regions are required: + * "hdmi_tx_l0" + * "hdmi_tx_l1" + * "hdmi_tx_l3" + * "hdmi_tx_l4" +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- core-vdda-supply: phandle to vdda regulator device node + Example: / { ... - hdmi: qcom,hdmi-tx-8960@4a00000 { + hdmi: hdmi@4a00000 { compatible = "qcom,hdmi-tx-8960"; reg-names = "core_physical"; - reg = <0x04a00000 0x1000>; + reg = <0x04a00000 0x2f0>; interrupts = <GIC_SPI 79 0>; power-domains = <&mmcc MDSS_GDSC>; clock-names = @@ -54,5 +80,21 @@ Example: pinctrl-names = "default", "sleep"; pinctrl-0 = <&hpd_active &ddc_active &cec_active>; pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>; + + phys = <&hdmi_phy>; + phy-names = "hdmi_phy"; + }; + + hdmi_phy: phy@4a00400 { + compatible = "qcom,hdmi-phy-8960"; + reg-names = "hdmi_phy", + "hdmi_pll"; + reg = <0x4a00400 0x60>, + <0x4a00500 0x100>; + #phy-cells = <0>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = "slave_iface_clk"; + clocks = <&mmcc HDMI_S_AHB_CLK>; + core-vdda-supply = <&pm8921_hdmi_mvs>; }; }; diff --git a/Documentation/devicetree/bindings/display/msm/mdp.txt b/Documentation/devicetree/bindings/display/msm/mdp.txt deleted file mode 100644 index a214f6cd0..000000000 --- a/Documentation/devicetree/bindings/display/msm/mdp.txt +++ /dev/null @@ -1,59 +0,0 @@ -Qualcomm adreno/snapdragon display controller - -Required properties: -- compatible: - * "qcom,mdp4" - mdp4 - * "qcom,mdp5" - mdp5 -- reg: Physical base address and length of the controller's registers. -- interrupts: The interrupt signal from the display controller. -- connectors: array of phandles for output device(s) -- clocks: device clocks - See ../clocks/clock-bindings.txt for details. -- clock-names: the following clocks are required. - For MDP4: - * "core_clk" - * "iface_clk" - * "lut_clk" - * "src_clk" - * "hdmi_clk" - * "mdp_clk" - For MDP5: - * "bus_clk" - * "iface_clk" - * "core_clk_src" - * "core_clk" - * "lut_clk" (some MDP5 versions may not need this) - * "vsync_clk" - -Optional properties: -- gpus: phandle for gpu device -- clock-names: the following clocks are optional: - * "lut_clk" - -Example: - -/ { - ... - - mdp: qcom,mdp@5100000 { - compatible = "qcom,mdp4"; - reg = <0x05100000 0xf0000>; - interrupts = <GIC_SPI 75 0>; - connectors = <&hdmi>; - gpus = <&gpu>; - clock-names = - "core_clk", - "iface_clk", - "lut_clk", - "src_clk", - "hdmi_clk", - "mdp_clk"; - clocks = - <&mmcc MDP_SRC>, - <&mmcc MDP_AHB_CLK>, - <&mmcc MDP_LUT_CLK>, - <&mmcc TV_SRC>, - <&mmcc HDMI_TV_CLK>, - <&mmcc MDP_TV_CLK>; - }; -}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp4.txt b/Documentation/devicetree/bindings/display/msm/mdp4.txt new file mode 100644 index 000000000..3c341a15c --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp4.txt @@ -0,0 +1,112 @@ +Qualcomm adreno/snapdragon MDP4 display controller + +Description: + +This is the bindings documentation for the MDP4 display controller found in +SoCs like MSM8960, APQ8064 and MSM8660. + +Required properties: +- compatible: + * "qcom,mdp4" - mdp4 +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the display controller. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "core_clk" + * "iface_clk" + * "bus_clk" + * "lut_clk" + * "hdmi_clk" + * "tv_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The output port mappings are: + Port 0 -> LCDC/LVDS + Port 1 -> DSI1 Cmd/Video + Port 2 -> DSI2 Cmd/Video + Port 3 -> DTV + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + hdmi: hdmi@4a00000 { + ... + ports { + ... + port@0 { + reg = <0>; + hdmi_in: endpoint { + remote-endpoint = <&mdp_dtv_out>; + }; + }; + ... + }; + ... + }; + + ... + + mdp: mdp@5100000 { + compatible = "qcom,mdp4"; + reg = <0x05100000 0xf0000>; + interrupts = <GIC_SPI 75 0>; + clock-names = + "core_clk", + "iface_clk", + "lut_clk", + "hdmi_clk", + "tv_clk"; + clocks = + <&mmcc MDP_CLK>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_AXI_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp_lvds_out: endpoint { + }; + }; + + port@1 { + reg = <1>; + mdp_dsi1_out: endpoint { + }; + }; + + port@2 { + reg = <2>; + mdp_dsi2_out: endpoint { + }; + }; + + port@3 { + reg = <3>; + mdp_dtv_out: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt new file mode 100644 index 000000000..30c11ea83 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp5.txt @@ -0,0 +1,160 @@ +Qualcomm adreno/snapdragon MDP5 display controller + +Description: + +This is the bindings documentation for the Mobile Display Subsytem(MDSS) that +encapsulates sub-blocks like MDP5, DSI, HDMI, eDP etc, and the MDP5 display +controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994 and MSM8996. + +MDSS: +Required properties: +- compatible: + * "qcom,mdss" - MDSS +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdss_phys" + * "vbif_phys" +- interrupts: The interrupt signal from MDSS. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "iface_clk" + * "bus_clk" + * "vsync_clk" +- #address-cells: number of address cells for the MDSS children. Should be 1. +- #size-cells: Should be 1. +- ranges: parent bus address space is the same as the child bus address space. + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +MDP5: +Required properties: +- compatible: + * "qcom,mdp5" - MDP5 +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdp_phys" +- interrupts: Interrupt line from MDP5 to MDSS interrupt controller. +- interrupt-parent: phandle to the MDSS block + through MDP block +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. +- * "bus_clk" +- * "iface_clk" +- * "core_clk" +- * "vsync_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The availability of output ports can vary across SoC revisions: + + For MSM8974 and APQ8084: + Port 0 -> MDP_INTF0 (eDP) + Port 1 -> MDP_INTF1 (DSI1) + Port 2 -> MDP_INTF2 (DSI2) + Port 3 -> MDP_INTF3 (HDMI) + + For MSM8916: + Port 0 -> MDP_INTF1 (DSI1) + + For MSM8994 and MSM8996: + Port 0 -> MDP_INTF1 (DSI1) + Port 1 -> MDP_INTF2 (DSI2) + Port 2 -> MDP_INTF3 (HDMI) + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + mdss: mdss@1a00000 { + compatible = "qcom,mdss"; + reg = <0x1a00000 0x1000>, + <0x1ac8000 0x3000>; + reg-names = "mdss_phys", "vbif_phys"; + + power-domains = <&gcc MDSS_GDSC>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "vsync_clk" + + interrupts = <0 72 0>; + + interrupt-controller; + #interrupt-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mdp: mdp@1a01000 { + compatible = "qcom,mdp5"; + reg = <0x1a01000 0x90000>; + reg-names = "mdp_phys"; + + interrupt-parent = <&mdss>; + interrupts = <0 0>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "core_clk", + "vsync_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp5_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi0: dsi@1a98000 { + ... + ports { + ... + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp5_intf1_out>; + }; + }; + ... + }; + ... + }; + + dsi_phy0: dsi-phy@1a98300 { + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt b/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt new file mode 100644 index 000000000..3e10cd782 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt @@ -0,0 +1,7 @@ +Innolux AT070TN92 7.0" WQVGA TFT LCD panel + +Required properties: +- compatible: should be "innolux,at070tn92" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt b/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt new file mode 100644 index 000000000..b9877acad --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt @@ -0,0 +1,7 @@ +LG LP079QX1-SP0V 7.9" (1536x2048 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp079qx1-sp0v" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt b/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt new file mode 100644 index 000000000..42141516f --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt @@ -0,0 +1,7 @@ +LG 9.7" (2048x1536 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp097qx1-spa1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp120up1.txt b/Documentation/devicetree/bindings/display/panel/lg,lp120up1.txt new file mode 100644 index 000000000..8c5de692c --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp120up1.txt @@ -0,0 +1,7 @@ +LG 12.0" (1920x1280 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp120up1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt new file mode 100644 index 000000000..74540a090 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt @@ -0,0 +1,7 @@ +Olimex 4.3" TFT LCD panel + +Required properties: +- compatible: should be "olimex,lcd-olinuxino-43-ts" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt new file mode 100644 index 000000000..3d8a5e029 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt @@ -0,0 +1,7 @@ +On Tat Industrial Company 7" DPI TFT panel. + +Required properties: +- compatible: should be "ontat,yx700wv03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt index 216c894d4..b52ac5275 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt +++ b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt @@ -7,6 +7,8 @@ Required properties: Optional properties: - label: a symbolic name for the panel - enable-gpios: panel enable gpio +- reset-gpios: GPIO to control the RESET pin +- vcc-supply: phandle of regulator that will be used to enable power to the display Required nodes: - "panel-timing" containing video timings diff --git a/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt b/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt new file mode 100644 index 000000000..dba298b43 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt @@ -0,0 +1,7 @@ +Samsung 12.2" (2560x1600 pixels) TFT LCD panel + +Required properties: +- compatible: should be "samsung,lsn122dl01-c01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt new file mode 100644 index 000000000..4aff25b8d --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt @@ -0,0 +1,7 @@ +Sharp Display Corp. LQ101K1LY04 10.07" WXGA TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq101k1ly04" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt new file mode 100644 index 000000000..bcb0e8a29 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt @@ -0,0 +1,7 @@ +Sharp 12.3" (2400x1600 pixels) TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq123p1jx31" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt b/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt new file mode 100644 index 000000000..1e87fe607 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt @@ -0,0 +1,7 @@ +Starry 12.2" (1920x1200 pixels) TFT LCD panel + +Required properties: +- compatible: should be "starry,kr122ea0sra" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt b/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt new file mode 100644 index 000000000..a2613b967 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt @@ -0,0 +1,8 @@ +TPK U.S.A. LLC Fusion 7" integrated projected capacitive touch display with, +800 x 480 (WVGA) LCD panel. + +Required properties: +- compatible: should be "tpk,f07a-0102" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt b/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt new file mode 100644 index 000000000..b9d051196 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt @@ -0,0 +1,8 @@ +TPK U.S.A. LLC Fusion 10.1" integrated projected capacitive touch display with, +1024 x 600 (WSVGA) LCD panel. + +Required properties: +- compatible: should be "tpk,f10a-0102" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/urt,umsh-8596md.txt b/Documentation/devicetree/bindings/display/panel/urt,umsh-8596md.txt new file mode 100644 index 000000000..088a6cea5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/urt,umsh-8596md.txt @@ -0,0 +1,16 @@ +United Radiant Technology UMSH-8596MD-xT 7.0" WVGA TFT LCD panel + +Supported are LVDS versions (-11T, -19T) and parallel ones +(-T, -1T, -7T, -20T). + +Required properties: +- compatible: should be one of: + "urt,umsh-8596md-t", + "urt,umsh-8596md-1t", + "urt,umsh-8596md-7t", + "urt,umsh-8596md-11t", + "urt,umsh-8596md-19t", + "urt,umsh-8596md-20t". + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index eccd4f486..0d30e42e4 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -8,6 +8,7 @@ Required Properties: - "renesas,du-r8a7791" for R8A7791 (R-Car M2-W) compatible DU - "renesas,du-r8a7793" for R8A7793 (R-Car M2-N) compatible DU - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU + - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU - reg: A list of base address and length of each memory resource, one for each entry in the reg-names property. @@ -24,7 +25,7 @@ Required Properties: - clock-names: Name of the clocks. This property is model-dependent. - R8A7779 uses a single functional clock. The clock doesn't need to be named. - - R8A779[0134] use one functional clock per channel and one clock per LVDS + - R8A779[01345] use one functional clock per channel and one clock per LVDS encoder (if available). The functional clocks must be named "du.x" with "x" being the channel numerical index. The LVDS clocks must be named "lvds.x" with "x" being the LVDS encoder numerical index. @@ -41,13 +42,14 @@ bindings specified in Documentation/devicetree/bindings/graph.txt. The following table lists for each supported model the port number corresponding to each DU output. - Port 0 Port1 Port2 + Port 0 Port1 Port2 Port3 ----------------------------------------------------------------------------- - R8A7779 (H1) DPAD 0 DPAD 1 - - R8A7790 (H2) DPAD LVDS 0 LVDS 1 - R8A7791 (M2-W) DPAD LVDS 0 - - R8A7793 (M2-N) DPAD LVDS 0 - - R8A7794 (E2) DPAD 0 DPAD 1 - + R8A7779 (H1) DPAD 0 DPAD 1 - - + R8A7790 (H2) DPAD LVDS 0 LVDS 1 - + R8A7791 (M2-W) DPAD LVDS 0 - - + R8A7793 (M2-N) DPAD LVDS 0 - - + R8A7794 (E2) DPAD 0 DPAD 1 - - + R8A7795 (H3) DPAD HDMI 0 HDMI 1 LVDS Example: R8A7790 (R-Car H2) DU diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt new file mode 100644 index 000000000..01cced1c2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt @@ -0,0 +1,99 @@ +Rockchip RK3288 specific extensions to the Analogix Display Port +================================ + +Required properties: +- compatible: "rockchip,rk3288-dp", + "rockchip,rk3399-edp"; + +- reg: physical base address of the controller and length + +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. + +- clock-names: from common clock binding: + Required elements: "dp" "pclk" + +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + +- pinctrl-names: Names corresponding to the chip hotplug pinctrl states. +- pinctrl-0: pin-control mode. should be <&edp_hpd> + +- reset-names: Must include the name "dp" + +- rockchip,grf: this soc should set GRF regs, so need get grf here. + +- ports: there are 2 port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0: contained 2 endpoints, connecting to the output of vop. + Port 1: contained 1 endpoint, connecting to the input of panel. + +Optional property for different chips: +- clocks: from common clock binding: handle to grf_vio clock. + +- clock-names: from common clock binding: + Required elements: "grf" + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt +- phys (required) +- phy-names (required) +- hpd-gpios (optional) +- force-hpd (optional) +------------------------------------------------------------------------------- + +Example: + dp-controller: dp@ff970000 { + compatible = "rockchip,rk3288-dp"; + reg = <0xff970000 0x4000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>; + clock-names = "dp", "pclk"; + phys = <&dp_phy>; + phy-names = "dp"; + + rockchip,grf = <&grf>; + resets = <&cru 111>; + reset-names = "dp"; + + pinctrl-names = "default"; + pinctrl-0 = <&edp_hpd>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + edp_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + edp_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_edp>; + }; + edp_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_edp>; + }; + }; + + edp_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + edp_out_panel: endpoint { + reg = <0>; + remote-endpoint = <&panel_in_edp> + }; + }; + }; + }; + + pinctrl { + edp { + edp_hpd: edp-hpd { + rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt new file mode 100644 index 000000000..8096a29f9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/inno_hdmi-rockchip.txt @@ -0,0 +1,50 @@ +Rockchip specific extensions to the Innosilicon HDMI +================================ + +Required properties: +- compatible: + "rockchip,rk3036-inno-hdmi"; +- reg: + Physical base address and length of the controller's registers. +- clocks, clock-names: + Phandle to hdmi controller clock, name should be "pclk" +- interrupts: + HDMI interrupt number +- ports: + Contain one port node with endpoint definitions as defined in + Documentation/devicetree/bindings/graph.txt. +- pinctrl-0, pinctrl-name: + Switch the iomux of HPD/CEC pins to HDMI function. + +Example: +hdmi: hdmi@20034000 { + compatible = "rockchip,rk3036-inno-hdmi"; + reg = <0x20034000 0x4000>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_HDMI>; + clock-names = "pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_ctl>; + status = "disabled"; + + hdmi_in: port { + #address-cells = <1>; + #size-cells = <0>; + hdmi_in_lcdc: endpoint@0 { + reg = <0>; + remote-endpoint = <&lcdc_out_hdmi>; + }; + }; +}; + +&pinctrl { + hdmi { + hdmi_ctl: hdmi-ctl { + rockchip,pins = <1 8 RK_FUNC_1 &pcfg_pull_none>, + <1 9 RK_FUNC_1 &pcfg_pull_none>, + <1 10 RK_FUNC_1 &pcfg_pull_none>, + <1 11 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + +}; diff --git a/Documentation/devicetree/bindings/display/snps,arcpgu.txt b/Documentation/devicetree/bindings/display/snps,arcpgu.txt new file mode 100644 index 000000000..c5c7dfd37 --- /dev/null +++ b/Documentation/devicetree/bindings/display/snps,arcpgu.txt @@ -0,0 +1,35 @@ +ARC PGU + +This is a display controller found on several development boards produced +by Synopsys. The ARC PGU is an RGB streamer that reads the data from a +framebuffer and sends it to a single digital encoder (usually HDMI). + +Required properties: + - compatible: "snps,arcpgu" + - reg: Physical base address and length of the controller's registers. + - clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. + - clock-names: A list of clock names. For ARC PGU it should contain: + - "pxlclk" for the clock feeding the output PLL of the controller. + +Required sub-nodes: + - port: The PGU connection to an encoder chip. + +Example: + +/ { + ... + + pgu@XXXXXXXX { + compatible = "snps,arcpgu"; + reg = <0xXXXXXXXX 0x400>; + clocks = <&clock_node>; + clock-names = "pxlclk"; + + port { + pgu_output: endpoint { + remote-endpoint = <&hdmi_enc_input>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt new file mode 100644 index 000000000..df8f4aeef --- /dev/null +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -0,0 +1,258 @@ +Allwinner A10 Display Pipeline +============================== + +The Allwinner A10 Display pipeline is composed of several components +that are going to be documented below: + +TV Encoder +---------- + +The TV Encoder supports the composite and VGA output. It is one end of +the pipeline. + +Required properties: + - compatible: value should be "allwinner,sun4i-a10-tv-encoder". + - reg: base address and size of memory-mapped region + - clocks: the clocks driving the TV encoder + - resets: phandle to the reset controller driving the encoder + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint. + +TCON +---- + +The TCON acts as a timing controller for RGB, LVDS and TV interfaces. + +Required properties: + - compatible: value should be "allwinner,sun5i-a13-tcon". + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the TCON. Three are needed: + - 'ahb': the interface clocks + - 'tcon-ch0': The clock driving the TCON channel 0 + - 'tcon-ch1': The clock driving the TCON channel 1 + - resets: phandles to the reset controllers driving the encoder + - "lcd": the reset line for the TCON channel 0 + + - clock-names: the clock names mentioned above + - reset-names: the reset names mentioned above + - clock-output-names: Name of the pixel clock created + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint, the second one the output + + The output should have two endpoints. The first is the block + connected to the TCON channel 0 (usually a panel or a bridge), the + second the block connected to the TCON channel 1 (usually the TV + encoder) + + +Display Engine Backend +---------------------- + +The display engine backend exposes layers and sprites to the +system. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-backend + - reg: base address and size of the memory-mapped region. + - clocks: phandles to the clocks feeding the frontend and backend + * ahb: the backend interface clock + * mod: the backend module clock + * ram: the backend DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the backend + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the output + +Display Engine Frontend +----------------------- + +The display engine frontend does formats conversion, scaling, +deinterlacing and color space conversion. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-frontend + - reg: base address and size of the memory-mapped region. + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the frontend and backend + * ahb: the backend interface clock + * mod: the backend module clock + * ram: the backend DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the backend + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the outputs + + +Display Engine Pipeline +----------------------- + +The display engine pipeline (and its entry point, since it can be +either directly the backend or the frontend) is represented as an +extra node. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-engine + + - allwinner,pipelines: list of phandle to the display engine + frontends available. + +Example: + +panel: panel { + compatible = "olimex,lcd-olinuxino-43-ts"; + #address-cells = <1>; + #size-cells = <0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + panel_input: endpoint { + remote-endpoint = <&tcon0_out_panel>; + }; + }; +}; + +tve0: tv-encoder@01c0a000 { + compatible = "allwinner,sun4i-a10-tv-encoder"; + reg = <0x01c0a000 0x1000>; + clocks = <&ahb_gates 34>; + resets = <&tcon_ch0_clk 0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + tve0_in_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_out_tve0>; + }; + }; +}; + +tcon0: lcd-controller@1c0c000 { + compatible = "allwinner,sun5i-a13-tcon"; + reg = <0x01c0c000 0x1000>; + interrupts = <44>; + resets = <&tcon_ch0_clk 1>; + reset-names = "lcd"; + clocks = <&ahb_gates 36>, + <&tcon_ch0_clk>, + <&tcon_ch1_clk>; + clock-names = "ahb", + "tcon-ch0", + "tcon-ch1"; + clock-output-names = "tcon-pixel-clock"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon0_in_be0: endpoint@0 { + reg = <0>; + remote-endpoint = <&be0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tcon0_out_panel: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + + tcon0_out_tve0: endpoint@1 { + reg = <1>; + remote-endpoint = <&tve0_in_tcon0>; + }; + }; + }; +}; + +fe0: display-frontend@1e00000 { + compatible = "allwinner,sun5i-a13-display-frontend"; + reg = <0x01e00000 0x20000>; + interrupts = <47>; + clocks = <&ahb_gates 46>, <&de_fe_clk>, + <&dram_gates 25>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_fe_clk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + fe0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + fe0_out_be0: endpoint { + remote-endpoint = <&be0_in_fe0>; + }; + }; + }; +}; + +be0: display-backend@1e60000 { + compatible = "allwinner,sun5i-a13-display-backend"; + reg = <0x01e60000 0x10000>; + clocks = <&ahb_gates 44>, <&de_be_clk>, + <&dram_gates 26>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_be_clk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + be0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + be0_in_fe0: endpoint@0 { + reg = <0>; + remote-endpoint = <&fe0_out_be0>; + }; + }; + + be0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + be0_out_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_in_be0>; + }; + }; + }; +}; + +display-engine { + compatible = "allwinner,sun5i-a13-display-engine"; + allwinner,pipelines = <&fe0>; +}; diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index a3bd8c050..0fad7ed2e 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -208,6 +208,7 @@ of the following host1x client modules: See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - sor: clock input for the SOR hardware + - source: source clock for the SOR clock - parent: input for the pixel clock - dp: reference clock for the SOR clock - safe: safe reference for the SOR clock during power up @@ -226,9 +227,9 @@ of the following host1x client modules: - nvidia,dpaux: phandle to a DispayPort AUX interface - dpaux: DisplayPort AUX interface - - compatible: For Tegra124, must contain "nvidia,tegra124-dpaux". Otherwise, - must contain '"nvidia,<chip>-dpaux", "nvidia,tegra124-dpaux"', where - <chip> is tegra132. + - compatible : Should contain one of the following: + - "nvidia,tegra124-dpaux": for Tegra124 and Tegra132 + - "nvidia,tegra210-dpaux": for Tegra210 - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. - clocks: Must contain an entry for each entry in clock-names. @@ -241,6 +242,12 @@ of the following host1x client modules: - reset-names: Must include the following entries: - dpaux - vdd-supply: phandle of a supply that powers the DisplayPort link + - i2c-bus: Subnode where I2C slave devices are listed. This subnode + must be always present. If there are no I2C slave devices, an empty + node should be added. See ../../i2c/i2c.txt for more information. + + See ../pinctrl/nvidia,tegra124-dpaux-padctl.txt for information + regarding the DPAUX pad controller bindings. Example: |