diff options
Diffstat (limited to 'Documentation/devicetree/bindings/drm')
14 files changed, 731 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt b/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt new file mode 100644 index 000000000..46525ea3e --- /dev/null +++ b/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt @@ -0,0 +1,30 @@ +Device Tree bindings for Armada DRM CRTC driver + +Required properties: + - compatible: value should be "marvell,dove-lcd". + - reg: base address and size of the LCD controller + - interrupts: single interrupt number for the LCD controller + - port: video output port with endpoints, as described by graph.txt + +Optional properties: + + - clocks: as described by clock-bindings.txt + - clock-names: as described by clock-bindings.txt + "axiclk" - axi bus clock for pixel clock + "plldivider" - pll divider clock for pixel clock + "ext_ref_clk0" - external clock 0 for pixel clock + "ext_ref_clk1" - external clock 1 for pixel clock + +Note: all clocks are optional but at least one must be specified. +Further clocks may be added in the future according to requirements of +different SoCs. + +Example: + + lcd0: lcd-controller@820000 { + compatible = "marvell,dove-lcd"; + reg = <0x820000 0x1000>; + interrupts = <47>; + clocks = <&si5351 0>; + clock-names = "ext_ref_clk_1"; + }; diff --git a/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt b/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt new file mode 100644 index 000000000..ebc1a914b --- /dev/null +++ b/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt @@ -0,0 +1,53 @@ +Device-Tree bindings for Atmel's HLCDC (High LCD Controller) DRM driver + +The Atmel HLCDC Display Controller is subdevice of the HLCDC MFD device. +See ../mfd/atmel-hlcdc.txt for more details. + +Required properties: + - compatible: value should be "atmel,hlcdc-display-controller" + - pinctrl-names: the pin control state names. Should contain "default". + - pinctrl-0: should contain the default pinctrl states. + - #address-cells: should be set to 1. + - #size-cells: should be set to 0. + +Required children nodes: + Children nodes are encoding available output ports and their connections + to external devices using the OF graph reprensentation (see ../graph.txt). + At least one port node is required. + +Example: + + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + status = "disabled"; + + hlcdc-display-controller { + compatible = "atmel,hlcdc-display-controller"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + hlcdc_panel_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + }; + }; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt b/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt new file mode 100644 index 000000000..a905c1413 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt @@ -0,0 +1,50 @@ +DesignWare HDMI bridge bindings + +Required properties: +- compatible: platform specific such as: + * "snps,dw-hdmi-tx" + * "fsl,imx6q-hdmi" + * "fsl,imx6dl-hdmi" + * "rockchip,rk3288-dw-hdmi" +- reg: Physical base address and length of the controller's registers. +- interrupts: The HDMI interrupt number +- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks, + as described in Documentation/devicetree/bindings/clock/clock-bindings.txt, + the clocks are soc specific, the clock-names should be "iahb", "isfr" +-port@[X]: SoC specific port nodes with endpoint definitions as defined + in Documentation/devicetree/bindings/media/video-interfaces.txt, + please refer to the SoC specific binding document: + * Documentation/devicetree/bindings/drm/imx/hdmi.txt + * Documentation/devicetree/bindings/video/dw_hdmi-rockchip.txt + +Optional properties +- reg-io-width: the width of the reg:1,4, default set to 1 if not present +- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing +- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec" + +Example: + hdmi: hdmi@0120000 { + compatible = "fsl,imx6q-hdmi"; + reg = <0x00120000 0x9000>; + interrupts = <0 115 0x04>; + gpr = <&gpr>; + clocks = <&clks 123>, <&clks 124>; + clock-names = "iahb", "isfr"; + ddc-i2c-bus = <&i2c2>; + + port@0 { + reg = <0>; + + hdmi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_hdmi>; + }; + }; + + port@1 { + reg = <1>; + + hdmi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_hdmi>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/drm/i2c/tda998x.txt b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt new file mode 100644 index 000000000..e9e4bce40 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for the NXP TDA998x HDMI transmitter + +Required properties; + - compatible: must be "nxp,tda998x" + + - reg: I2C address + +Optional properties: + - interrupts: interrupt number and trigger type + default: polling + + - pinctrl-0: pin control group to be used for + screen plug/unplug interrupt. + + - pinctrl-names: must contain a "default" entry. + + - video-ports: 24 bits value which defines how the video controller + output is wired to the TDA998x input - default: <0x230145> + +Example: + + tda998x: hdmi-encoder { + compatible = "nxp,tda998x"; + reg = <0x70>; + interrupt-parent = <&gpio0>; + interrupts = <27 2>; /* falling edge */ + pinctrl-0 = <&pmx_camera>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt new file mode 100644 index 000000000..e75f0e549 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt @@ -0,0 +1,83 @@ +Freescale i.MX DRM master device +================================ + +The freescale i.MX DRM master device is a virtual device needed to list all +IPU or other display interface nodes that comprise the graphics subsystem. + +Required properties: +- compatible: Should be "fsl,imx-display-subsystem" +- ports: Should contain a list of phandles pointing to display interface ports + of IPU devices + +example: + +display-subsystem { + compatible = "fsl,display-subsystem"; + ports = <&ipu_di0>; +}; + + +Freescale i.MX IPUv3 +==================== + +Required properties: +- compatible: Should be "fsl,<chip>-ipu" +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain sync interrupt and error interrupt, + in this order. +- resets: phandle pointing to the system reset controller and + reset line index, see reset/fsl,imx-src.txt for details +Optional properties: +- port@[0-3]: Port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Ports 0 and 1 should correspond to CSI0 and CSI1, + ports 2 and 3 should correspond to DI0 and DI1, respectively. + +example: + +ipu: ipu@18000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ipu"; + reg = <0x18000000 0x080000000>; + interrupts = <11 10>; + resets = <&src 2>; + + ipu_di0: port@2 { + reg = <2>; + + ipu_di0_disp0: endpoint { + remote-endpoint = <&display_in>; + }; + }; +}; + +Parallel display support +======================== + +Required properties: +- compatible: Should be "fsl,imx-parallel-display" +Optional properties: +- interface_pix_fmt: How this display is connected to the + display interface. Currently supported types: "rgb24", "rgb565", "bgr666" + and "lvds666". +- edid: verbatim EDID data block describing attached display. +- ddc: phandle describing the i2c bus handling the display data + channel +- port: A port node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + +example: + +display@di0 { + compatible = "fsl,imx-parallel-display"; + edid = [edid-data]; + interface-pix-fmt = "rgb24"; + + port { + display_in: endpoint { + remote-endpoint = <&ipu_di0_disp0>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/imx/hdmi.txt b/Documentation/devicetree/bindings/drm/imx/hdmi.txt new file mode 100644 index 000000000..1b756cf9a --- /dev/null +++ b/Documentation/devicetree/bindings/drm/imx/hdmi.txt @@ -0,0 +1,58 @@ +Device-Tree bindings for HDMI Transmitter + +HDMI Transmitter +================ + +The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP +with accompanying PHY IP. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi". + - gpr : should be <&gpr>. + The phandle points to the iomuxc-gpr region containing the HDMI + multiplexer control register. + - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described + in Documentation/devicetree/bindings/clock/clock-bindings.txt and + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + - port@[0-4]: Up to four port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt, + corresponding to the four inputs to the HDMI multiplexer. + +Optional properties: + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + +example: + + gpr: iomuxc-gpr@020e0000 { + /* ... */ + }; + + hdmi: hdmi@0120000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx6q-hdmi"; + reg = <0x00120000 0x9000>; + interrupts = <0 115 0x04>; + gpr = <&gpr>; + clocks = <&clks 123>, <&clks 124>; + clock-names = "iahb", "isfr"; + ddc-i2c-bus = <&i2c2>; + + port@0 { + reg = <0>; + + hdmi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_hdmi>; + }; + }; + + port@1 { + reg = <1>; + + hdmi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_hdmi>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/drm/imx/ldb.txt b/Documentation/devicetree/bindings/drm/imx/ldb.txt new file mode 100644 index 000000000..9a2136643 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/imx/ldb.txt @@ -0,0 +1,146 @@ +Device-Tree bindings for LVDS Display Bridge (ldb) + +LVDS Display Bridge +=================== + +The LVDS Display Bridge device tree node contains up to two lvds-channel +nodes describing each of the two LVDS encoder channels of the bridge. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". + Both LDB versions are similar, but i.MX6 has an additional + multiplexer in the front to select any of the four IPU display + interfaces as input for each LVDS channel. + - gpr : should be <&gpr> on i.MX53 and i.MX6q. + The phandle points to the iomuxc-gpr region containing the LVDS + control register. +- clocks, clock-names : phandles to the LDB divider and selector clocks and to + the display interface selector clocks, as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt + The following clocks are expected on i.MX53: + "di0_pll" - LDB LVDS channel 0 mux + "di1_pll" - LDB LVDS channel 1 mux + "di0" - LDB LVDS channel 0 gate + "di1" - LDB LVDS channel 1 gate + "di0_sel" - IPU1 DI0 mux + "di1_sel" - IPU1 DI1 mux + On i.MX6q the following additional clocks are needed: + "di2_sel" - IPU2 DI0 mux + "di3_sel" - IPU2 DI1 mux + The needed clock numbers for each are documented in + Documentation/devicetree/bindings/clock/imx5-clock.txt, and in + Documentation/devicetree/bindings/clock/imx6q-clock.txt. + +Optional properties: + - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q + - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, + not used on i.MX6q + - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should + be configured - one input will be distributed on both outputs in dual + channel mode + +LVDS Channel +============ + +Each LVDS Channel has to contain either an of graph link to a panel device node +or a display-timings node that describes the video timings for the connected +LVDS display as well as the fsl,data-mapping and fsl,data-width properties. + +Required properties: + - reg : should be <0> or <1> + - port: Input and output port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/graph.txt. + On i.MX5, the internal two-input-multiplexer is used. Due to hardware + limitations, only one input port (port@[0,1]) can be used for each channel + (lvds-channel@[0,1], respectively). + On i.MX6, there should be four input ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. + A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected + to a panel input port. Optionally, the output port can be left out if + display-timings are used instead. + +Optional properties (required if display-timings are used): + - display-timings : A node that describes the display timings as defined in + Documentation/devicetree/bindings/video/display-timing.txt. + - fsl,data-mapping : should be "spwg" or "jeida" + This describes how the color bits are laid out in the + serialized LVDS signal. + - fsl,data-width : should be <18> or <24> + +example: + +gpr: iomuxc-gpr@53fa8000 { + /* ... */ +}; + +ldb: ldb@53fa8008 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ldb"; + gpr = <&gpr>; + clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, + <&clks IMX5_CLK_LDB_DI1_SEL>, + <&clks IMX5_CLK_IPU_DI0_SEL>, + <&clks IMX5_CLK_IPU_DI1_SEL>, + <&clks IMX5_CLK_LDB_DI0_GATE>, + <&clks IMX5_CLK_LDB_DI1_GATE>; + clock-names = "di0_pll", "di1_pll", + "di0_sel", "di1_sel", + "di0", "di1"; + + /* Using an of-graph endpoint link to connect the panel */ + lvds-channel@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + port@0 { + reg = <0>; + + lvds0_in: endpoint { + remote-endpoint = <&ipu_di0_lvds0>; + }; + }; + + port@2 { + reg = <2>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + /* Using display-timings and fsl,data-mapping/width instead */ + lvds-channel@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + + port@1 { + reg = <1>; + + lvds1_in: endpoint { + remote-endpoint = <&ipu_di1_lvds1>; + }; + }; + }; +}; + +panel: lvds-panel { + /* ... */ + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/msm/gpu.txt b/Documentation/devicetree/bindings/drm/msm/gpu.txt new file mode 100644 index 000000000..67d0a58db --- /dev/null +++ b/Documentation/devicetree/bindings/drm/msm/gpu.txt @@ -0,0 +1,52 @@ +Qualcomm adreno/snapdragon GPU + +Required properties: +- compatible: "qcom,adreno-3xx" +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the gpu. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core_clk" + * "iface_clk" + * "mem_iface_clk" +- qcom,chipid: gpu chip-id. Note this may become optional for future + devices if we can reliably read the chipid from hw +- qcom,gpu-pwrlevels: list of operating points + - compatible: "qcom,gpu-pwrlevels" + - for each qcom,gpu-pwrlevel: + - qcom,gpu-freq: requested gpu clock speed + - NOTE: downstream android driver defines additional parameters to + configure memory bandwidth scaling per OPP. + +Example: + +/ { + ... + + gpu: qcom,kgsl-3d0@4300000 { + compatible = "qcom,adreno-3xx"; + reg = <0x04300000 0x20000>; + reg-names = "kgsl_3d0_reg_memory"; + interrupts = <GIC_SPI 80 0>; + interrupt-names = "kgsl_3d0_irq"; + clock-names = + "core_clk", + "iface_clk", + "mem_iface_clk"; + clocks = + <&mmcc GFX3D_CLK>, + <&mmcc GFX3D_AHB_CLK>, + <&mmcc MMSS_IMEM_AHB_CLK>; + qcom,chipid = <0x03020100>; + qcom,gpu-pwrlevels { + compatible = "qcom,gpu-pwrlevels"; + qcom,gpu-pwrlevel@0 { + qcom,gpu-freq = <450000000>; + }; + qcom,gpu-pwrlevel@1 { + qcom,gpu-freq = <27000000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/msm/hdmi.txt b/Documentation/devicetree/bindings/drm/msm/hdmi.txt new file mode 100644 index 000000000..a29a55f3d --- /dev/null +++ b/Documentation/devicetree/bindings/drm/msm/hdmi.txt @@ -0,0 +1,48 @@ +Qualcomm adreno/snapdragon hdmi output + +Required properties: +- compatible: one of the following + * "qcom,hdmi-tx-8084" + * "qcom,hdmi-tx-8074" + * "qcom,hdmi-tx-8660" + * "qcom,hdmi-tx-8960" +- reg: Physical base address and length of the controller's registers +- reg-names: "core_physical" +- interrupts: The interrupt signal from the hdmi block. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin +- qcom,hdmi-tx-ddc-data-gpio: ddc data pin +- qcom,hdmi-tx-hpd-gpio: hpd pin +- core-vdda-supply: phandle to supply regulator +- hdmi-mux-supply: phandle to mux regulator + +Optional properties: +- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin +- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin + +Example: + +/ { + ... + + hdmi: qcom,hdmi-tx-8960@4a00000 { + compatible = "qcom,hdmi-tx-8960"; + reg-names = "core_physical"; + reg = <0x04a00000 0x1000>; + interrupts = <GIC_SPI 79 0>; + clock-names = + "core_clk", + "master_iface_clk", + "slave_iface_clk"; + clocks = + <&mmcc HDMI_APP_CLK>, + <&mmcc HDMI_M_AHB_CLK>, + <&mmcc HDMI_S_AHB_CLK>; + qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>; + qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>; + qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>; + core-vdda-supply = <&pm8921_hdmi_mvs>; + hdmi-mux-supply = <&ext_3p3v>; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/msm/mdp.txt b/Documentation/devicetree/bindings/drm/msm/mdp.txt new file mode 100644 index 000000000..1a0598e52 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/msm/mdp.txt @@ -0,0 +1,48 @@ +Qualcomm adreno/snapdragon display controller + +Required properties: +- compatible: + * "qcom,mdp" - mdp4 +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the display controller. +- connectors: array of phandles for output device(s) +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core_clk" + * "iface_clk" + * "lut_clk" + * "src_clk" + * "hdmi_clk" + * "mpd_clk" + +Optional properties: +- gpus: phandle for gpu device + +Example: + +/ { + ... + + mdp: qcom,mdp@5100000 { + compatible = "qcom,mdp"; + reg = <0x05100000 0xf0000>; + interrupts = <GIC_SPI 75 0>; + connectors = <&hdmi>; + gpus = <&gpu>; + clock-names = + "core_clk", + "iface_clk", + "lut_clk", + "src_clk", + "hdmi_clk", + "mdp_clk"; + clocks = + <&mmcc MDP_SRC>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc TV_SRC>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + }; +}; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt new file mode 100644 index 000000000..4ab9e2300 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt @@ -0,0 +1,66 @@ +Device-Tree bindings for tilcdc DRM generic panel output driver + +Required properties: + - compatible: value should be "ti,tilcdc,panel". + - panel-info: configuration info to configure LCDC correctly for the panel + - ac-bias: AC Bias Pin Frequency + - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt + - dma-burst-sz: DMA burst size + - bpp: Bits per pixel + - fdd: FIFO DMA Request Delay + - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling + - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore + - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most + - fifo-th: DMA FIFO threshold + - display-timings: typical videomode of lcd panel. Multiple video modes + can be listed if the panel supports multiple timings, but the 'native-mode' + should be the preferred/default resolution. Refer to + Documentation/devicetree/bindings/video/display-timing.txt for display + timing binding details. + +Optional properties: +- backlight: phandle of the backlight device attached to the panel +- enable-gpios: GPIO pin to enable or disable the panel + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + /* Settings for CDTech_S035Q01 / LCD3 cape: */ + lcd3 { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + backlight = <&backlight>; + enable-gpios = <&gpio3 19 0>; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + native-mode = <&timing0>; + timing0: 320x240 { + hactive = <320>; + vactive = <240>; + hback-porch = <21>; + hfront-porch = <58>; + hsync-len = <47>; + vback-porch = <11>; + vfront-porch = <23>; + vsync-len = <2>; + clock-frequency = <8000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt new file mode 100644 index 000000000..3d2c52460 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt @@ -0,0 +1,18 @@ +Device-Tree bindings for tilcdc DRM encoder slave output driver + +Required properties: + - compatible: value should be "ti,tilcdc,slave". + - i2c: the phandle for the i2c device the encoder slave is connected to + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + hdmi { + compatible = "ti,tilcdc,slave"; + i2c = <&i2c0>; + pinctrl-names = "default"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt new file mode 100644 index 000000000..a58ae7756 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt @@ -0,0 +1,21 @@ +Device-Tree bindings for tilcdc DRM TFP410 output driver + +Required properties: + - compatible: value should be "ti,tilcdc,tfp410". + - i2c: the phandle for the i2c device to use for DDC + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + - powerdn-gpio: the powerdown GPIO, pulled low to power down the + TFP410 device (for DPMS_OFF) + +Example: + + dvicape { + compatible = "ti,tilcdc,tfp410"; + i2c = <&i2c2>; + pinctrl-names = "default"; + pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>; + powerdn-gpio = <&gpio2 31 0>; + }; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt new file mode 100644 index 000000000..fff10da5e --- /dev/null +++ b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for tilcdc DRM driver + +Required properties: + - compatible: value should be "ti,am33xx-tilcdc". + - interrupts: the interrupt number + - reg: base address and size of the LCDC device + +Recommended properties: + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + - ti,hwmods: Name of the hwmod associated to the LCDC + +Optional properties: + - max-bandwidth: The maximum pixels per second that the memory + interface / lcd controller combination can sustain + - max-width: The maximum horizontal pixel width supported by + the lcd controller. + - max-pixelclock: The maximum pixel clock that can be supported + by the lcd controller in KHz. + +Example: + + fb: fb@4830e000 { + compatible = "ti,am33xx-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + }; |