diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd/max8998.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/max8998.txt | 119 |
1 files changed, 119 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt new file mode 100644 index 000000000..23a3650ff --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8998.txt @@ -0,0 +1,119 @@ +* Maxim MAX8998, National/TI LP3974 multi-function device + +The Maxim MAX8998 is a multi-function device which includes voltage/current +regulators, real time clock, battery charging controller and several +other sub-blocks. It is interfaced using an I2C interface. Each sub-block +is addressed by the host system using different i2c slave address. + +PMIC sub-block +-------------- + +The PMIC sub-block contains a number of voltage and current regulators, +with controllable parameters and dynamic voltage scaling capability. +In addition, it includes a real time clock and battery charging controller +as well. It is accessible at I2C address 0x66. + +Required properties: +- compatible: Should be one of the following: + - "maxim,max8998" for Maxim MAX8998 + - "national,lp3974" or "ti,lp3974" for National/TI LP3974. +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from MAX8998 are routed to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for main interrupt. + - Second interrupt specifier is for power-on/-off interrupt. +- max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used + for buck 1 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used + for buck 2 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from + the possible 4 options selectable by the dvs gpios. The value of this + property should be 0, 1, 2 or 3. If not specified or out of range, + a default value of 0 is taken. +- max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from + the possible 2 options selectable by the dvs gpios. The value of this + property should be 0 or 1. If not specified or out of range, a default + value of 0 is taken. +- max8998,pmic-buck-voltage-lock: If present, disallows changing of + preprogrammed buck dvfs voltages. + +Additional properties required if max8998,pmic-buck1-dvs-gpios is defined: +- max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts + for buck1 regulator that can be selected using dvs gpio. + +Additional properties required if max8998,pmic-buck2-dvs-gpio is defined: +- max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts + for buck2 regulator that can be selected using dvs gpio. + +Regulators: All the regulators of MAX8998 to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the MAX8998 PMIC block are supported. Note that +the 'n' in regulator name, as in LDOn or BUCKn, represents the LDO or BUCK +number as described in MAX8998 datasheet. + + - LDOn + - valid values for n are 2 to 17 + - Example: LDO2, LDO10, LDO17 + - BUCKn + - valid values for n are 1 to 4. + - Example: BUCK1, BUCK2, BUCK3, BUCK4 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details. + +Example: + + pmic@66 { + compatible = "maxim,max8998-pmic"; + reg = <0x66>; + interrupt-parent = <&wakeup_eint>; + interrupts = <4 0>, <3 0>; + + /* Buck 1 DVS settings */ + max8998,pmic-buck1-default-dvs-idx = <0>; + max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>; /* SET2 */ + max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1000000>, <950000>; + + /* Buck 2 DVS settings */ + max8998,pmic-buck2-default-dvs-idx = <0>; + max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */ + max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>; + + /* Regulators to instantiate */ + regulators { + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; |