summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/net/stmmac.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/net/stmmac.txt')
-rw-r--r--Documentation/devicetree/bindings/net/stmmac.txt54
1 files changed, 37 insertions, 17 deletions
diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt
index e862a922b..6605d1960 100644
--- a/Documentation/devicetree/bindings/net/stmmac.txt
+++ b/Documentation/devicetree/bindings/net/stmmac.txt
@@ -17,7 +17,25 @@ Required properties:
The 1st cell is reset pre-delay in micro seconds.
The 2nd cell is reset pulse in micro seconds.
The 3rd cell is reset post-delay in micro seconds.
+
+Optional properties:
+- resets: Should contain a phandle to the STMMAC reset signal, if any
+- reset-names: Should contain the reset signal name "stmmaceth", if a
+ reset phandle is given
+- max-frame-size: See ethernet.txt file in the same directory
+- clocks: If present, the first clock should be the GMAC main clock and
+ the second clock should be peripheral's register interface clock. Further
+ clocks may be specified in derived bindings.
+- clock-names: One name for each entry in the clocks property, the
+ first one should be "stmmaceth" and the second one should be "pclk".
+- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is
+ available this clock is used for programming the Timestamp Addend Register.
+ If not passed then the system clock will be used and this is fine on some
+ platforms.
+- tx-fifo-depth: See ethernet.txt file in the same directory
+- rx-fifo-depth: See ethernet.txt file in the same directory
- snps,pbl Programmable Burst Length
+- snps,aal Address-Aligned Beats
- snps,fixed-burst Program the DMA to use the fixed burst mode
- snps,mixed-burst Program the DMA to use the mixed burst mode
- snps,force_thresh_dma_mode Force DMA to use the threshold mode for
@@ -29,27 +47,28 @@ Required properties:
supported by this device instance
- snps,perfect-filter-entries: Number of perfect filter entries supported
by this device instance
-
-Optional properties:
-- resets: Should contain a phandle to the STMMAC reset signal, if any
-- reset-names: Should contain the reset signal name "stmmaceth", if a
- reset phandle is given
-- max-frame-size: See ethernet.txt file in the same directory
-- clocks: If present, the first clock should be the GMAC main clock
- The optional second clock should be peripheral's register interface clock.
- The third optional clock should be the ptp reference clock.
- Further clocks may be specified in derived bindings.
-- clock-names: One name for each entry in the clocks property.
- The first one should be "stmmaceth".
- The optional second one should be "pclk".
- The optional third one should be "clk_ptp_ref".
-- snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register.
-- tx-fifo-depth: See ethernet.txt file in the same directory
-- rx-fifo-depth: See ethernet.txt file in the same directory
+- AXI BUS Mode parameters: below the list of all the parameters to program the
+ AXI register inside the DMA module:
+ - snps,lpi_en: enable Low Power Interface
+ - snps,xit_frm: unlock on WoL
+ - snps,wr_osr_lmt: max write oustanding req. limit
+ - snps,rd_osr_lmt: max read oustanding req. limit
+ - snps,kbbe: do not cross 1KiB boundary.
+ - snps,axi_all: align address
+ - snps,blen: this is a vector of supported burst length.
+ - snps,fb: fixed-burst
+ - snps,mb: mixed-burst
+ - snps,rb: rebuild INCRx Burst
- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus.
Examples:
+ stmmac_axi_setup: stmmac-axi-config {
+ snps,wr_osr_lmt = <0xf>;
+ snps,rd_osr_lmt = <0xf>;
+ snps,blen = <256 128 64 32 0 0 0>;
+ };
+
gmac0: ethernet@e0800000 {
compatible = "st,spear600-gmac";
reg = <0xe0800000 0x8000>;
@@ -65,6 +84,7 @@ Examples:
tx-fifo-depth = <16384>;
clocks = <&clock>;
clock-names = "stmmaceth";
+ snps,axi-config = <&stmmac_axi_setup>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;