summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/power
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/power')
-rw-r--r--Documentation/devicetree/bindings/power/qcom,coincell-charger.txt2
-rw-r--r--Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt48
-rw-r--r--Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt36
-rw-r--r--Documentation/devicetree/bindings/power/reset/gpio-restart.txt54
-rw-r--r--Documentation/devicetree/bindings/power/rockchip-io-domain.txt4
5 files changed, 142 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt
index 0e6d8754e..747899223 100644
--- a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt
+++ b/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt
@@ -29,7 +29,7 @@ IC (PMIC)
- qcom,charger-disable:
Usage: optional
Value type: <boolean>
- Definition: definining this property disables charging
+ Definition: defining this property disables charging
This charger is a sub-node of one of the 8941 PMIC blocks, and is specified
as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and
diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
new file mode 100644
index 000000000..b74e4d478
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
@@ -0,0 +1,48 @@
+DT bindings for the Renesas R-Car System Controller
+
+== System Controller Node ==
+
+The R-Car System Controller provides power management for the CPU cores and
+various coprocessors.
+
+Required properties:
+ - compatible: Must contain exactly one of the following:
+ - "renesas,r8a7779-sysc" (R-Car H1)
+ - "renesas,r8a7790-sysc" (R-Car H2)
+ - "renesas,r8a7791-sysc" (R-Car M2-W)
+ - "renesas,r8a7792-sysc" (R-Car V2H)
+ - "renesas,r8a7793-sysc" (R-Car M2-N)
+ - "renesas,r8a7794-sysc" (R-Car E2)
+ - "renesas,r8a7795-sysc" (R-Car H3)
+ - reg: Address start and address range for the device.
+ - #power-domain-cells: Must be 1.
+
+
+Example:
+
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7791-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
+
+== PM Domain Consumers ==
+
+Devices residing in a power area must refer to that power area, as documented
+by the generic PM domain bindings in
+Documentation/devicetree/bindings/power/power_domain.txt.
+
+Required properties:
+ - power-domains: A phandle and symbolic PM domain specifier, as defined in
+ <dt-bindings/power/r8a77*-sysc.h>.
+
+
+Example:
+
+ L2_CA15: cache-controller@0 {
+ compatible = "cache";
+ power-domains = <&sysc R8A7791_PD_CA15_SCU>;
+ cache-unified;
+ cache-level = <2>;
+ };
diff --git a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt
new file mode 100644
index 000000000..d4eab9227
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt
@@ -0,0 +1,36 @@
+Driver a GPIO line that can be used to turn the power off.
+
+The driver supports both level triggered and edge triggered power off.
+At driver load time, the driver will request the given gpio line and
+install a pm_power_off handler. If the optional properties 'input' is
+not found, the GPIO line will be driven in the inactive
+state. Otherwise its configured as an input.
+
+When the pm_power_off is called, the gpio is configured as an output,
+and drive active, so triggering a level triggered power off
+condition. This will also cause an inactive->active edge condition, so
+triggering positive edge triggered power off. After a delay of 100ms,
+the GPIO is set to inactive, thus causing an active->inactive edge,
+triggering negative edge triggered power off. After another 100ms
+delay the GPIO is driver active again. If the power is still on and
+the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted.
+
+Required properties:
+- compatible : should be "gpio-poweroff".
+- gpios : The GPIO to set high/low, see "gpios property" in
+ Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
+ low to power down the board set it to "Active Low", otherwise set
+ gpio to "Active High".
+
+Optional properties:
+- input : Initially configure the GPIO line as an input. Only reconfigure
+ it to an output when the pm_power_off function is called. If this optional
+ property is not specified, the GPIO is initialized as an output in its
+ inactive state.
+
+Examples:
+
+gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio 4 0>;
+};
diff --git a/Documentation/devicetree/bindings/power/reset/gpio-restart.txt b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt
new file mode 100644
index 000000000..af3701bc1
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/gpio-restart.txt
@@ -0,0 +1,54 @@
+Drive a GPIO line that can be used to restart the system from a restart
+handler.
+
+This binding supports level and edge triggered reset. At driver load
+time, the driver will request the given gpio line and install a restart
+handler. If the optional properties 'open-source' is not found, the GPIO line
+will be driven in the inactive state. Otherwise its not driven until
+the restart is initiated.
+
+When the system is restarted, the restart handler will be invoked in
+priority order. The gpio is configured as an output, and driven active,
+triggering a level triggered reset condition. This will also cause an
+inactive->active edge condition, triggering positive edge triggered
+reset. After a delay specified by active-delay, the GPIO is set to
+inactive, thus causing an active->inactive edge, triggering negative edge
+triggered reset. After a delay specified by inactive-delay, the GPIO
+is driven active again. After a delay specified by wait-delay, the
+restart handler completes allowing other restart handlers to be attempted.
+
+Required properties:
+- compatible : should be "gpio-restart".
+- gpios : The GPIO to set high/low, see "gpios property" in
+ Documentation/devicetree/bindings/gpio/gpio.txt. If the pin should be
+ low to reset the board set it to "Active Low", otherwise set
+ gpio to "Active High".
+
+Optional properties:
+- open-source : Treat the GPIO as being open source and defer driving
+ it to when the restart is initiated. If this optional property is not
+ specified, the GPIO is initialized as an output in its inactive state.
+- priority : A priority ranging from 0 to 255 (default 128) according to
+ the following guidelines:
+ 0: Restart handler of last resort, with limited restart
+ capabilities
+ 128: Default restart handler; use if no other restart handler is
+ expected to be available, and/or if restart functionality is
+ sufficient to restart the entire system
+ 255: Highest priority restart handler, will preempt all other
+ restart handlers
+- active-delay: Delay (default 100) to wait after driving gpio active [ms]
+- inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms]
+- wait-delay: Delay (default 3000) to wait after completing restart
+ sequence [ms]
+
+Examples:
+
+gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio 4 0>;
+ priority = <128>;
+ active-delay = <100>;
+ inactive-delay = <100>;
+ wait-delay = <3000>;
+};
diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt
index c84fb4726..d23dc002a 100644
--- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt
+++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt
@@ -37,8 +37,10 @@ Required properties:
- "rockchip,rk3368-pmu-io-voltage-domain" for rk3368 pmu-domains
- "rockchip,rk3399-io-voltage-domain" for rk3399
- "rockchip,rk3399-pmu-io-voltage-domain" for rk3399 pmu-domains
-- rockchip,grf: phandle to the syscon managing the "general register files"
+Deprecated properties:
+- rockchip,grf: phandle to the syscon managing the "general register files"
+ Systems should move the io-domains to a sub-node of the grf simple-mfd.
You specify supplies using the standard regulator bindings by including
a phandle the relevant regulator. All specified supplies must be able