summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/spi
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
-rw-r--r--Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt34
-rw-r--r--Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt8
-rw-r--r--Documentation/devicetree/bindings/spi/sqi-pic32.txt18
-rw-r--r--Documentation/devicetree/bindings/spi/ti_qspi.txt7
4 files changed, 64 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt
new file mode 100644
index 000000000..79de379f4
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/microchip,spi-pic32.txt
@@ -0,0 +1,34 @@
+Microchip PIC32 SPI Master controller
+
+Required properties:
+- compatible: Should be "microchip,pic32mzda-spi".
+- reg: Address and length of register space for the device.
+- interrupts: Should contain all three spi interrupts in sequence
+ of <fault-irq>, <receive-irq>, <transmit-irq>.
+- interrupt-names: Should be "fault", "rx", "tx" in order.
+- clocks: Phandle of the clock generating SPI clock on the bus.
+- clock-names: Should be "mck0".
+- cs-gpios: Specifies the gpio pins to be used for chipselects.
+ See: Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Optional properties:
+- dmas: Two or more DMA channel specifiers following the convention outlined
+ in Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: Names for the dma channels. There must be at least one channel
+ named "spi-tx" for transmit and named "spi-rx" for receive.
+
+Example:
+
+spi1: spi@1f821000 {
+ compatible = "microchip,pic32mzda-spi";
+ reg = <0x1f821000 0x200>;
+ interrupts = <109 IRQ_TYPE_LEVEL_HIGH>,
+ <110 IRQ_TYPE_LEVEL_HIGH>,
+ <111 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "fault", "rx", "tx";
+ clocks = <&PBCLK2>;
+ clock-names = "mck0";
+ cs-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+ dmas = <&dma 134>, <&dma 135>;
+ dma-names = "spi-rx", "spi-tx";
+};
diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
index fa77f874e..ff5893d27 100644
--- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
+++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
@@ -1,7 +1,10 @@
ARM Freescale DSPI controller
Required properties:
-- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi", "fsl,ls2085a-dspi"
+- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi",
+ "fsl,ls2085a-dspi"
+ or
+ "fsl,ls2080a-dspi" followed by "fsl,ls2085a-dspi"
- reg : Offset and length of the register set for the device
- interrupts : Should contain SPI controller interrupt
- clocks: from common clock binding: handle to dspi clock.
@@ -13,8 +16,7 @@ Required properties:
Optional property:
- big-endian: If present the dspi device's registers are implemented
- in big endian mode, otherwise in native mode(same with CPU), for more
- detail please see: Documentation/devicetree/bindings/regmap/regmap.txt.
+ in big endian mode.
Optional SPI slave node properties:
- fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip
diff --git a/Documentation/devicetree/bindings/spi/sqi-pic32.txt b/Documentation/devicetree/bindings/spi/sqi-pic32.txt
new file mode 100644
index 000000000..c82d021bc
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/sqi-pic32.txt
@@ -0,0 +1,18 @@
+Microchip PIC32 Quad SPI controller
+-----------------------------------
+Required properties:
+- compatible: Should be "microchip,pic32mzda-sqi".
+- reg: Address and length of SQI controller register space.
+- interrupts: Should contain SQI interrupt.
+- clocks: Should contain phandle of two clocks in sequence, one that drives
+ clock on SPI bus and other that drives SQI controller.
+- clock-names: Should be "spi_ck" and "reg_ck" in order.
+
+Example:
+ sqi1: spi@1f8e2000 {
+ compatible = "microchip,pic32mzda-sqi";
+ reg = <0x1f8e2000 0x200>;
+ clocks = <&rootclk REF2CLK>, <&rootclk PB5CLK>;
+ clock-names = "spi_ck", "reg_ck";
+ interrupts = <169 IRQ_TYPE_LEVEL_HIGH>;
+ };
diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt
index cc8304aa6..50b14f6b5 100644
--- a/Documentation/devicetree/bindings/spi/ti_qspi.txt
+++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt
@@ -19,6 +19,13 @@ Optional properties:
- syscon-chipselects: Handle to system control region contains QSPI
chipselect register and offset of that register.
+NOTE: TI QSPI controller requires different pinmux and IODelay
+paramaters for Mode-0 and Mode-3 operations, which needs to be set up by
+the bootloader (U-Boot). Default configuration only supports Mode-0
+operation. Hence, "spi-cpol" and "spi-cpha" DT properties cannot be
+specified in the slave nodes of TI QSPI controller without appropriate
+modification to bootloader.
+
Example:
For am4372: