diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb')
9 files changed, 204 insertions, 16 deletions
diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt index 5883b73ea..f4262ed60 100644 --- a/Documentation/devicetree/bindings/usb/atmel-usb.txt +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -113,13 +113,13 @@ usb2: gadget@fff78000 { clock-names = "hclk", "pclk"; atmel,vbus-gpio = <&pioB 19 0>; - ep0 { + ep@0 { reg = <0>; atmel,fifo-size = <64>; atmel,nb-banks = <1>; }; - ep1 { + ep@1 { reg = <1>; atmel,fifo-size = <1024>; atmel,nb-banks = <2>; @@ -127,7 +127,7 @@ usb2: gadget@fff78000 { atmel,can-isoc; }; - ep2 { + ep@2 { reg = <2>; atmel,fifo-size = <1024>; atmel,nb-banks = <2>; @@ -135,21 +135,21 @@ usb2: gadget@fff78000 { atmel,can-isoc; }; - ep3 { + ep@3 { reg = <3>; atmel,fifo-size = <1024>; atmel,nb-banks = <3>; atmel,can-dma; }; - ep4 { + ep@4 { reg = <4>; atmel,fifo-size = <1024>; atmel,nb-banks = <3>; atmel,can-dma; }; - ep5 { + ep@5 { reg = <5>; atmel,fifo-size = <1024>; atmel,nb-banks = <3>; @@ -157,7 +157,7 @@ usb2: gadget@fff78000 { atmel,can-isoc; }; - ep6 { + ep@6 { reg = <6>; atmel,fifo-size = <1024>; atmel,nb-banks = <3>; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 781296bfb..341dc67f3 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -2,7 +2,14 @@ Required properties: - compatible: should be one of: + "fsl,imx23-usb" "fsl,imx27-usb" + "fsl,imx28-usb" + "fsl,imx6q-usb" + "fsl,imx6sl-usb" + "fsl,imx6sx-usb" + "fsl,imx6ul-usb" + "fsl,imx7d-usb" "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" @@ -53,6 +60,22 @@ Optional properties: be specified. - phy-clkgate-delay-us: the delay time (us) between putting the PHY into low power mode and gating the PHY clock. +- non-zero-ttctrl-ttha: after setting this property, the value of register + ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it is + recommended that consult with your IC engineer before setting this value. + On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this + property only affects siTD. + If this property is not set, the max packet size is 1023 bytes, and if + the total of packet size for pervious transactions are more than 256 bytes, + it can't accept any transactions within this frame. The use case is single + transaction, but higher frame rate. + If this property is set, the max packet size is 188 bytes, it can handle + more transactions than above case, it can accept transactions until it + considers the left room size within frame is less than 188 bytes, software + needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple transactions, but + less frame rate. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one @@ -70,7 +93,7 @@ Example: phys = <&usb_phy0>; phy-names = "usb-phy"; vbus-supply = <®_usb0_vbus>; - gadget-itc-setting = <0x4>; /* 4 micro-frames */ + itc-setting = <0x4>; /* 4 micro-frames */ /* Incremental burst of unspecified length */ ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 221368207..20a68bf2b 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -8,6 +8,8 @@ Required properties: - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; + - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs; + - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs; - snps,dwc2: A generic DWC2 USB controller with default parameters. - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index fb2ad0ace..7d7ce089b 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -14,7 +14,6 @@ Optional properties: the second element is expected to be a handle to the USB3/SS PHY - phys: from the *Generic PHY* bindings - phy-names: from the *Generic PHY* bindings - - tx-fifo-resize: determines if the FIFO *has* to be reallocated. - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. @@ -38,6 +37,8 @@ Optional properties: - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal to the PHY. + - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection + in PHY P3 power state. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold @@ -47,6 +48,8 @@ Optional properties: register for post-silicon frame length adjustment when the fladj_30mhz_sdbnd signal is invalid or incorrect. + - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. + This is usually a subnode to DWC3 glue to which it is connected. dwc3@4a030000 { @@ -54,5 +57,4 @@ dwc3@4a030000 { reg = <0x4a030000 0xcfff>; interrupts = <0 92 4> usb-phy = <&usb2_phy>, <&usb3,phy>; - tx-fifo-resize; }; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt new file mode 100644 index 000000000..3eee9e505 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt @@ -0,0 +1,120 @@ +NVIDIA Tegra xHCI controller +============================ + +The Tegra xHCI controller supports both USB2 and USB3 interfaces exposed by +the Tegra XUSB pad controller. + +Required properties: +-------------------- +- compatible: Must be: + - Tegra124: "nvidia,tegra124-xusb" + - Tegra132: "nvidia,tegra132-xusb", "nvidia,tegra124-xusb" + - Tegra210: "nvidia,tegra210-xusb" +- reg: Must contain the base and length of the xHCI host registers, XUSB FPCI + registers and XUSB IPFS registers. +- reg-names: Must contain the following entries: + - "hcd" + - "fpci" + - "ipfs" +- interrupts: Must contain the xHCI host interrupt and the mailbox interrupt. +- clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - xusb_host + - xusb_host_src + - xusb_falcon_src + - xusb_ss + - xusb_ss_src + - xusb_ss_div2 + - xusb_hs_src + - xusb_fs_src + - pll_u_480m + - clk_m + - pll_e +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - xusb_host + - xusb_ss + - xusb_src + Note that xusb_src is the shared reset for xusb_{ss,hs,fs,falcon,host}_src. +- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to + configure the USB pads used by the XHCI controller + +For Tegra124 and Tegra132: +- avddio-pex-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V. +- dvddio-pex-supply: PCIe/USB3 digital logic power supply. Must supply 1.05 V. +- avdd-usb-supply: USB controller power supply. Must supply 3.3 V. +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- avdd-usb-ss-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-usb-ss-supply: High-voltage PCIe/USB3 power supply. Must supply 3.3 V. +- hvdd-usb-ss-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V. + +For Tegra210: +- dvddio-pex-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V. +- hvddio-pex-supply: High-voltage PCIe/USB3 power supply. Must supply 1.8 V. +- avdd-usb-supply: USB controller power supply. Must supply 3.3 V. +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. + +Optional properties: +-------------------- +- phys: Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names: Should include an entry for each PHY used by the controller. The + following PHYs are available: + - Tegra124: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 + - Tegra132: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 + - Tegra210: usb2-0, usb2-1, usb2-2, usb2-3, hsic-0, usb3-0, usb3-1, usb3-2, + usb3-3 + +Example: +-------- + + usb@0,70090000 { + compatible = "nvidia,tegra124-xusb"; + reg = <0x0 0x70090000 0x0 0x8000>, + <0x0 0x70098000 0x0 0x1000>, + <0x0 0x70099000 0x0 0x1000>; + reg-names = "hcd", "fpci", "ipfs"; + + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&tegra_car TEGRA124_CLK_XUSB_HOST>, + <&tegra_car TEGRA124_CLK_XUSB_HOST_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_FALCON_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_SS>, + <&tegra_car TEGRA124_CLK_XUSB_SS_DIV2>, + <&tegra_car TEGRA124_CLK_XUSB_SS_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_HS_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_FS_SRC>, + <&tegra_car TEGRA124_CLK_PLL_U_480M>, + <&tegra_car TEGRA124_CLK_CLK_M>, + <&tegra_car TEGRA124_CLK_PLL_E>; + clock-names = "xusb_host", "xusb_host_src", "xusb_falcon_src", + "xusb_ss", "xusb_ss_div2", "xusb_ss_src", + "xusb_hs_src", "xusb_fs_src", "pll_u_480m", + "clk_m", "pll_e"; + resets = <&tegra_car 89>, <&tegra_car 156>, <&tegra_car 143>; + reset-names = "xusb_host", "xusb_ss", "xusb_src"; + + nvidia,xusb-padctl = <&padctl>; + + phys = <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-1}>, /* mini-PCIe USB */ + <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-2}>, /* USB A */ + <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-0}>; /* USB A */ + phy-names = "usb2-1", "usb2-2", "usb3-0"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-usb-supply = <&vdd_3v3_lp0>; + avdd-pll-utmip-supply = <&vddio_1v8>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + avdd-usb-ss-pll-supply = <&vdd_1v05_run>; + hvdd-usb-ss-supply = <&vdd_3v3_lp0>; + hvdd-usb-ss-pll-e-supply = <&vdd_3v3_lp0>; + }; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index ca164e71d..39acb084b 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -59,7 +59,6 @@ Example device nodes: interrupts = <0 205 0x4>; phys = <&hs_phy>, <&ss_phy>; phy-names = "usb2-phy", "usb3-phy"; - tx-fifo-resize; dr_mode = "host"; }; }; diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt new file mode 100644 index 000000000..1c35e7b66 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -0,0 +1,28 @@ +Generic USB Device Properties + +Usually, we only use device tree for hard wired USB device. +The reference binding doc is from: +http://www.firmware.org/1275/bindings/usb/usb-1_0.ps + +Required properties: +- compatible: usbVID,PID. The textual representation of VID, PID shall + be in lower case hexadecimal with leading zeroes suppressed. The + other compatible strings from the above standard binding could also + be used, but a device adhering to this binding may leave out all except + for usbVID,PID. +- reg: the port number which this device is connecting to, the range + is 1-31. + +Example: + +&usb1 { + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + hub: genesys@1 { + compatible = "usb5e3,608"; + reg = <1>; + }; +} diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 19233b736..9df456968 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -14,7 +14,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" -- resets : phandle + reset specifier pair +- resets : a list of phandle + reset specifier pairs Example: diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 082573289..966885c63 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -1,10 +1,24 @@ USB xHCI controllers Required properties: - - compatible: should be one of "generic-xhci", - "marvell,armada-375-xhci", "marvell,armada-380-xhci", - "renesas,xhci-r8a7790", "renesas,xhci-r8a7791", "renesas,xhci-r8a7793", - "renesas,xhci-r8a7795" (deprecated: "xhci-platform"). + - compatible: should be one or more of + + - "generic-xhci" for generic XHCI device + - "marvell,armada3700-xhci" for Armada 37xx SoCs + - "marvell,armada-375-xhci" for Armada 375 SoCs + - "marvell,armada-380-xhci" for Armada 38x SoCs + - "renesas,xhci-r8a7790" for r8a7790 SoC + - "renesas,xhci-r8a7791" for r8a7791 SoC + - "renesas,xhci-r8a7793" for r8a7793 SoC + - "renesas,xhci-r8a7795" for r8a7795 SoC + - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 compatible device + - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device + - "xhci-platform" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. |