1 files changed, 39 insertions, 158 deletions

diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c
index 0c1825b0b..315c84979 100644
--- a/drivers/tty/serial/crisv10.c
+++ b/drivers/tty/serial/crisv10.c
@@ -56,10 +56,6 @@ static char *serial_version = "$Revision: 1.25 $";
 #error "RX_TIMEOUT_TICKS == 0 not allowed, use 1"
 #endif
 
-#if defined(CONFIG_ETRAX_RS485_ON_PA) && defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-#error "Disable either CONFIG_ETRAX_RS485_ON_PA or CONFIG_ETRAX_RS485_ON_PORT_G"
-#endif
-
 /*
  * All of the compatibilty code so we can compile serial.c against
  * older kernels is hidden in serial_compat.h
@@ -455,30 +451,6 @@ static struct e100_serial rs_table[] = {
 static struct fast_timer fast_timers[NR_PORTS];
 #endif
 
-#ifdef CONFIG_ETRAX_SERIAL_PROC_ENTRY
-#define PROCSTAT(x) x
-struct ser_statistics_type {
-	int overrun_cnt;
-	int early_errors_cnt;
-	int ser_ints_ok_cnt;
-	int errors_cnt;
-	unsigned long int processing_flip;
-	unsigned long processing_flip_still_room;
-	unsigned long int timeout_flush_cnt;
-	int rx_dma_ints;
-	int tx_dma_ints;
-	int rx_tot;
-	int tx_tot;
-};
-
-static struct ser_statistics_type ser_stat[NR_PORTS];
-
-#else
-
-#define PROCSTAT(x)
-
-#endif /* CONFIG_ETRAX_SERIAL_PROC_ENTRY */
-
 /* RS-485 */
 #if defined(CONFIG_ETRAX_RS485)
 #ifdef CONFIG_ETRAX_FAST_TIMER
@@ -487,9 +459,6 @@ static struct fast_timer fast_timers_rs485[NR_PORTS];
 #if defined(CONFIG_ETRAX_RS485_ON_PA)
 static int rs485_pa_bit = CONFIG_ETRAX_RS485_ON_PA_BIT;
 #endif
-#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-static int rs485_port_g_bit = CONFIG_ETRAX_RS485_ON_PORT_G_BIT;
-#endif
 #endif
 
 /* Info and macros needed for each ports extra control/status signals. */
@@ -739,10 +708,10 @@ static unsigned char dummy_ser[NR_PORTS] = {0xFF, 0xFF, 0xFF,0xFF};
     defined(CONFIG_ETRAX_SER1_DTR_RI_DSR_CD_MIXED) || \
     defined(CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_MIXED) || \
     defined(CONFIG_ETRAX_SER3_DTR_RI_DSR_CD_MIXED)
-#define CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED
+#define ETRAX_SERX_DTR_RI_DSR_CD_MIXED
 #endif
 
-#ifdef CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED
+#ifdef ETRAX_SERX_DTR_RI_DSR_CD_MIXED
 /* The pins can be mixed on PA and PB */
 #define CONTROL_PINS_PORT_NOT_USED(line) \
   &dummy_ser[line], &dummy_ser[line], \
@@ -835,7 +804,7 @@ static const struct control_pins e100_modem_pins[NR_PORTS] =
 #endif
 	}
 };
-#else  /* CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
+#else  /* ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
 
 /* All pins are on either PA or PB for each serial port */
 #define CONTROL_PINS_PORT_NOT_USED(line) \
@@ -917,7 +886,7 @@ static const struct control_pins e100_modem_pins[NR_PORTS] =
 #endif
 	}
 };
-#endif /* !CONFIG_ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
+#endif /* !ETRAX_SERX_DTR_RI_DSR_CD_MIXED */
 
 #define E100_RTS_MASK 0x20
 #define E100_CTS_MASK 0x40
@@ -1367,16 +1336,6 @@ e100_enable_rs485(struct tty_struct *tty, struct serial_rs485 *r)
 #if defined(CONFIG_ETRAX_RS485_ON_PA)
 	*R_PORT_PA_DATA = port_pa_data_shadow |= (1 << rs485_pa_bit);
 #endif
-#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-	REG_SHADOW_SET(R_PORT_G_DATA,  port_g_data_shadow,
-		       rs485_port_g_bit, 1);
-#endif
-#if defined(CONFIG_ETRAX_RS485_LTC1387)
-	REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-		       CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 1);
-	REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-		       CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 1);
-#endif
 
 	info->rs485 = *r;
 
@@ -1454,9 +1413,8 @@ rs_stop(struct tty_struct *tty)
 		xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char,
 				STOP_CHAR(info->port.tty));
 		xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, stop);
-		if (tty->termios.c_iflag & IXON ) {
+		if (I_IXON(tty))
 			xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
-		}
 
 		*((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
 		local_irq_restore(flags);
@@ -1477,9 +1435,8 @@ rs_start(struct tty_struct *tty)
 					 info->xmit.tail,SERIAL_XMIT_SIZE)));
 		xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(tty));
 		xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
-		if (tty->termios.c_iflag & IXON ) {
+		if (I_IXON(tty))
 			xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
-		}
 
 		*((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
 		if (!info->uses_dma_out &&
@@ -1676,7 +1633,8 @@ alloc_recv_buffer(unsigned int size)
 {
 	struct etrax_recv_buffer *buffer;
 
-	if (!(buffer = kmalloc(sizeof *buffer + size, GFP_ATOMIC)))
+	buffer = kmalloc(sizeof *buffer + size, GFP_ATOMIC);
+	if (!buffer)
 		return NULL;
 
 	buffer->next = NULL;
@@ -1712,7 +1670,8 @@ add_char_and_flag(struct e100_serial *info, unsigned char data, unsigned char fl
 {
 	struct etrax_recv_buffer *buffer;
 	if (info->uses_dma_in) {
-		if (!(buffer = alloc_recv_buffer(4)))
+		buffer = alloc_recv_buffer(4);
+		if (!buffer)
 			return 0;
 
 		buffer->length = 1;
@@ -1750,7 +1709,8 @@ static unsigned int handle_descr_data(struct e100_serial *info,
 
 	append_recv_buffer(info, buffer);
 
-	if (!(buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE)))
+	buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE);
+	if (!buffer)
 		panic("%s: Failed to allocate memory for receive buffer!\n", __func__);
 
 	descr->buf = virt_to_phys(buffer->buffer);
@@ -1841,7 +1801,6 @@ static void receive_chars_dma(struct e100_serial *info)
 		 */
 		unsigned char data = info->ioport[REG_DATA];
 
-		PROCSTAT(ser_stat[info->line].errors_cnt++);
 		DEBUG_LOG(info->line, "#dERR: s d 0x%04X\n",
 			  ((rstat & SER_ERROR_MASK) << 8) | data);
 
@@ -1867,7 +1826,8 @@ static int start_recv_dma(struct e100_serial *info)
 
 	/* Set up the receiving descriptors */
 	for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++) {
-		if (!(buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE)))
+		buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE);
+		if (!buffer)
 			panic("%s: Failed to allocate memory for receive buffer!\n", __func__);
 
 		descr[i].ctrl = d_int;
@@ -1943,7 +1903,6 @@ tr_interrupt(int irq, void *dev_id)
 			/* Read jiffies_usec first,
 			 * we want this time to be as late as possible
 			 */
- 			PROCSTAT(ser_stat[info->line].tx_dma_ints++);
 			info->last_tx_active_usec = GET_JIFFIES_USEC();
 			info->last_tx_active = jiffies;
 			transmit_chars_dma(info);
@@ -2022,7 +1981,6 @@ static int force_eop_if_needed(struct e100_serial *info)
 	 */
 	if (!info->forced_eop) {
 		info->forced_eop = 1;
-		PROCSTAT(ser_stat[info->line].timeout_flush_cnt++);
 		TIMERD(DEBUG_LOG(info->line, "timeout EOP %i\n", info->line));
 		FORCE_EOP(info);
 	}
@@ -2374,7 +2332,6 @@ static void handle_ser_rx_interrupt(struct e100_serial *info)
 			DEBUG_LOG(info->line, "#iERR s d %04X\n",
 			          ((rstat & SER_ERROR_MASK) << 8) | data);
 		}
-		PROCSTAT(ser_stat[info->line].early_errors_cnt++);
 	} else { /* It was a valid byte, now let the DMA do the rest */
 		unsigned long curr_time_u = GET_JIFFIES_USEC();
 		unsigned long curr_time = jiffies;
@@ -2407,7 +2364,6 @@ static void handle_ser_rx_interrupt(struct e100_serial *info)
 		DINTR2(DEBUG_LOG(info->line, "ser_rx OK %d\n", info->line));
 		info->break_detected_cnt = 0;
 
-		PROCSTAT(ser_stat[info->line].ser_ints_ok_cnt++);
 	}
 	/* Restarting the DMA never hurts */
 	*info->icmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, restart);
@@ -2643,7 +2599,7 @@ startup(struct e100_serial * info)
 
 	/* if it was already initialized, skip this */
 
-	if (info->port.flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(&info->port)) {
 		local_irq_restore(flags);
 		free_page(xmit_page);
 		return 0;
@@ -2747,7 +2703,7 @@ startup(struct e100_serial * info)
 	e100_rts(info, 1);
 	e100_dtr(info, 1);
 
-	info->port.flags |= ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 1);
 
 	local_irq_restore(flags);
 	return 0;
@@ -2789,7 +2745,7 @@ shutdown(struct e100_serial * info)
 		info->tr_running = 0;
 	}
 
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!tty_port_initialized(&info->port))
 		return;
 
 #ifdef SERIAL_DEBUG_OPEN
@@ -2820,7 +2776,7 @@ shutdown(struct e100_serial * info)
 	if (info->port.tty)
 		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
 
-	info->port.flags &= ~ASYNC_INITIALIZED;
+	tty_port_set_initialized(&info->port, 0);
 	local_irq_restore(flags);
 }
 
@@ -2867,19 +2823,6 @@ change_speed(struct e100_serial *info)
 			*R_SERIAL_PRESCALE = divisor;
 			info->baud = SERIAL_PRESCALE_BASE/divisor;
 		}
-#ifdef CONFIG_ETRAX_EXTERN_PB6CLK_ENABLED
-		else if ((info->baud_base==CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8 &&
-			  info->custom_divisor == 1) ||
-			 (info->baud_base==CONFIG_ETRAX_EXTERN_PB6CLK_FREQ &&
-			  info->custom_divisor == 8)) {
-				/* ext_clk selected */
-				alt_source =
-					IO_STATE(R_ALT_SER_BAUDRATE, ser0_rec, extern) |
-					IO_STATE(R_ALT_SER_BAUDRATE, ser0_tr, extern);
-				DBAUD(printk("using external baudrate: %lu\n", CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8));
-				info->baud = CONFIG_ETRAX_EXTERN_PB6CLK_FREQ/8;
-			}
-#endif
 		else
 		{
 			/* Bad baudbase, we don't support using timer0
@@ -3023,7 +2966,7 @@ static int rs_raw_write(struct tty_struct *tty,
 
 	local_save_flags(flags);
 	DFLOW(DEBUG_LOG(info->line, "write count %i ", count));
-	DFLOW(DEBUG_LOG(info->line, "ldisc %i\n", tty->ldisc.chars_in_buffer(tty)));
+	DFLOW(DEBUG_LOG(info->line, "ldisc\n"));
 
 
 	/* The local_irq_disable/restore_flags pairs below are needed
@@ -3216,15 +3159,12 @@ rs_throttle(struct tty_struct * tty)
 {
 	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
 #ifdef SERIAL_DEBUG_THROTTLE
-	char	buf[64];
-
-	printk("throttle %s: %lu....\n", tty_name(tty, buf),
-	       (unsigned long)tty->ldisc.chars_in_buffer(tty));
+	printk("throttle %s ....\n", tty_name(tty));
 #endif
-	DFLOW(DEBUG_LOG(info->line,"rs_throttle %lu\n", tty->ldisc.chars_in_buffer(tty)));
+	DFLOW(DEBUG_LOG(info->line,"rs_throttle\n"));
 
 	/* Do RTS before XOFF since XOFF might take some time */
-	if (tty->termios.c_cflag & CRTSCTS) {
+	if (C_CRTSCTS(tty)) {
 		/* Turn off RTS line */
 		e100_rts(info, 0);
 	}
@@ -3238,15 +3178,12 @@ rs_unthrottle(struct tty_struct * tty)
 {
 	struct e100_serial *info = (struct e100_serial *)tty->driver_data;
 #ifdef SERIAL_DEBUG_THROTTLE
-	char	buf[64];
-
-	printk("unthrottle %s: %lu....\n", tty_name(tty, buf),
-	       (unsigned long)tty->ldisc.chars_in_buffer(tty));
+	printk("unthrottle %s ....\n", tty_name(tty));
 #endif
-	DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc %d\n", tty->ldisc.chars_in_buffer(tty)));
+	DFLOW(DEBUG_LOG(info->line,"rs_unthrottle ldisc\n"));
 	DFLOW(DEBUG_LOG(info->line,"rs_unthrottle flip.count: %i\n", tty->flip.count));
 	/* Do RTS before XOFF since XOFF might take some time */
-	if (tty->termios.c_cflag & CRTSCTS) {
+	if (C_CRTSCTS(tty)) {
 		/* Assert RTS line  */
 		e100_rts(info, 1);
 	}
@@ -3336,9 +3273,9 @@ set_serial_info(struct e100_serial *info,
 	info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 
  check_and_exit:
-	if (info->port.flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(&info->port))
 		change_speed(info);
-	} else
+	else
 		retval = startup(info);
 	return retval;
 }
@@ -3508,7 +3445,7 @@ rs_ioctl(struct tty_struct *tty,
 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
 	    (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD)  &&
 	    (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
-		if (tty->flags & (1 << TTY_IO_ERROR))
+		if (tty_io_error(tty))
 			return -EIO;
 	}
 
@@ -3614,8 +3551,7 @@ rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
 	change_speed(info);
 
 	/* Handle turning off CRTSCTS */
-	if ((old_termios->c_cflag & CRTSCTS) &&
-	    !(tty->termios.c_cflag & CRTSCTS))
+	if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty))
 		rs_start(tty);
 
 }
@@ -3674,7 +3610,6 @@ rs_close(struct tty_struct *tty, struct file * filp)
 		local_irq_restore(flags);
 		return;
 	}
-	info->port.flags |= ASYNC_CLOSING;
 	/*
 	 * Now we wait for the transmit buffer to clear; and we notify
 	 * the line discipline to only process XON/XOFF characters.
@@ -3693,7 +3628,7 @@ rs_close(struct tty_struct *tty, struct file * filp)
 	e100_disable_rx(info);
 	e100_disable_rx_irq(info);
 
-	if (info->port.flags & ASYNC_INITIALIZED) {
+	if (tty_port_initialized(&info->port)) {
 		/*
 		 * Before we drop DTR, make sure the UART transmitter
 		 * has completely drained; this is especially
@@ -3713,9 +3648,8 @@ rs_close(struct tty_struct *tty, struct file * filp)
 			schedule_timeout_interruptible(info->port.close_delay);
 		wake_up_interruptible(&info->port.open_wait);
 	}
-	info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
-	wake_up_interruptible(&info->port.close_wait);
 	local_irq_restore(flags);
+	tty_port_set_active(&info->port, 0);
 
 	/* port closed */
 
@@ -3725,16 +3659,6 @@ rs_close(struct tty_struct *tty, struct file * filp)
 #if defined(CONFIG_ETRAX_RS485_ON_PA)
 		*R_PORT_PA_DATA = port_pa_data_shadow &= ~(1 << rs485_pa_bit);
 #endif
-#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-		REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-			       rs485_port_g_bit, 0);
-#endif
-#if defined(CONFIG_ETRAX_RS485_LTC1387)
-		REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-			       CONFIG_ETRAX_RS485_LTC1387_DXEN_PORT_G_BIT, 0);
-		REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow,
-			       CONFIG_ETRAX_RS485_LTC1387_RXEN_PORT_G_BIT, 0);
-#endif
 	}
 #endif
 
@@ -3808,7 +3732,7 @@ rs_hangup(struct tty_struct *tty)
 	shutdown(info);
 	info->event = 0;
 	info->port.count = 0;
-	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+	tty_port_set_active(&info->port, 0);
 	info->port.tty = NULL;
 	wake_up_interruptible(&info->port.open_wait);
 }
@@ -3828,35 +3752,16 @@ block_til_ready(struct tty_struct *tty, struct file * filp,
 	int		do_clocal = 0;
 
 	/*
-	 * If the device is in the middle of being closed, then block
-	 * until it's done, and then try again.
-	 */
-	if (info->port.flags & ASYNC_CLOSING) {
-		wait_event_interruptible_tty(tty, info->port.close_wait,
-			!(info->port.flags & ASYNC_CLOSING));
-#ifdef SERIAL_DO_RESTART
-		if (info->port.flags & ASYNC_HUP_NOTIFY)
-			return -EAGAIN;
-		else
-			return -ERESTARTSYS;
-#else
-		return -EAGAIN;
-#endif
-	}
-
-	/*
 	 * If non-blocking mode is set, or the port is not enabled,
 	 * then make the check up front and then exit.
 	 */
-	if ((filp->f_flags & O_NONBLOCK) ||
-	    (tty->flags & (1 << TTY_IO_ERROR))) {
-		info->port.flags |= ASYNC_NORMAL_ACTIVE;
+	if ((filp->f_flags & O_NONBLOCK) || tty_io_error(tty)) {
+		tty_port_set_active(&info->port, 1);
 		return 0;
 	}
 
-	if (tty->termios.c_cflag & CLOCAL) {
-			do_clocal = 1;
-	}
+	if (C_CLOCAL(tty))
+		do_clocal = 1;
 
 	/*
 	 * Block waiting for the carrier detect and the line to become
@@ -3882,8 +3787,7 @@ block_til_ready(struct tty_struct *tty, struct file * filp,
 		e100_dtr(info, 1);
 		local_irq_restore(flags);
 		set_current_state(TASK_INTERRUPTIBLE);
-		if (tty_hung_up_p(filp) ||
-		    !(info->port.flags & ASYNC_INITIALIZED)) {
+		if (tty_hung_up_p(filp) || !tty_port_initialized(&info->port)) {
 #ifdef SERIAL_DO_RESTART
 			if (info->port.flags & ASYNC_HUP_NOTIFY)
 				retval = -EAGAIN;
@@ -3894,7 +3798,7 @@ block_til_ready(struct tty_struct *tty, struct file * filp,
 #endif
 			break;
 		}
-		if (!(info->port.flags & ASYNC_CLOSING) && do_clocal)
+		if (do_clocal)
 			/* && (do_clocal || DCD_IS_ASSERTED) */
 			break;
 		if (signal_pending(current)) {
@@ -3920,7 +3824,7 @@ block_til_ready(struct tty_struct *tty, struct file * filp,
 #endif
 	if (retval)
 		return retval;
-	info->port.flags |= ASYNC_NORMAL_ACTIVE;
+	tty_port_set_active(&info->port, 1);
 	return 0;
 }
 
@@ -3964,20 +3868,6 @@ rs_open(struct tty_struct *tty, struct file * filp)
 	info->port.low_latency = !!(info->port.flags & ASYNC_LOW_LATENCY);
 
 	/*
-	 * If the port is in the middle of closing, bail out now
-	 */
-	if (info->port.flags & ASYNC_CLOSING) {
-		wait_event_interruptible_tty(tty, info->port.close_wait,
-			!(info->port.flags & ASYNC_CLOSING));
-#ifdef SERIAL_DO_RESTART
-		return ((info->port.flags & ASYNC_HUP_NOTIFY) ?
-			-EAGAIN : -ERESTARTSYS);
-#else
-		return -EAGAIN;
-#endif
-	}
-
-	/*
 	 * If DMA is enabled try to allocate the irq's.
 	 */
 	if (info->port.count == 1) {
@@ -4263,15 +4153,6 @@ static int __init rs_init(void)
 		return -EBUSY;
 	}
 #endif
-#if defined(CONFIG_ETRAX_RS485_ON_PORT_G)
-	if (cris_io_interface_allocate_pins(if_serial_0, 'g', rs485_pa_bit,
-			rs485_port_g_bit)) {
-		printk(KERN_ERR "ETRAX100LX serial: Could not allocate "
-			"RS485 pin\n");
-		put_tty_driver(driver);
-		return -EBUSY;
-	}
-#endif
 #endif
 
 	/* Initialize the tty_driver structure */