4 files changed, 15 insertions, 4 deletions
diff --git a/drivers/usb/chipidea/Kconfig b/drivers/usb/chipidea/Kconfig
index 3644a3500..5e5b9eb7e 100644
--- a/drivers/usb/chipidea/Kconfig
+++ b/drivers/usb/chipidea/Kconfig
@@ -4,8 +4,9 @@ config USB_CHIPIDEA
 	select EXTCON
 	help
 	  Say Y here if your system has a dual role high speed USB
-	  controller based on ChipIdea silicon IP. Currently, only the
-	  peripheral mode is supported.
+	  controller based on ChipIdea silicon IP. It supports:
+	  Dual-role switch (ID, OTG FSM, sysfs), Host-only, and
+	  Peripheral-only.
 
 	  When compiled dynamically, the module will be called ci-hdrc.ko.
 
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 69426e644..3dbb4a21a 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -914,6 +914,7 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 	if (!ci)
 		return -ENOMEM;
 
+	spin_lock_init(&ci->lock);
 	ci->dev = dev;
 	ci->platdata = dev_get_platdata(dev);
 	ci->imx28_write_fix = !!(ci->platdata->flags &
diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
index 053bac9d9..887be343f 100644
--- a/drivers/usb/chipidea/host.c
+++ b/drivers/usb/chipidea/host.c
@@ -185,6 +185,8 @@ static void host_stop(struct ci_hdrc *ci)
 
 	if (hcd) {
 		usb_remove_hcd(hcd);
+		ci->role = CI_ROLE_END;
+		synchronize_irq(ci->irq);
 		usb_put_hcd(hcd);
 		if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) &&
 			(ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON))
diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index dfec5a176..bced28fa1 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -949,6 +949,15 @@ static int isr_setup_status_phase(struct ci_hdrc *ci)
 	int retval;
 	struct ci_hw_ep *hwep;
 
+	/*
+	 * Unexpected USB controller behavior, caused by bad signal integrity
+	 * or ground reference problems, can lead to isr_setup_status_phase
+	 * being called with ci->status equal to NULL.
+	 * If this situation occurs, you should review your USB hardware design.
+	 */
+	if (WARN_ON_ONCE(!ci->status))
+		return -EPIPE;
+
 	hwep = (ci->ep0_dir == TX) ? ci->ep0out : ci->ep0in;
 	ci->status->context = ci;
 	ci->status->complete = isr_setup_status_complete;
@@ -1886,8 +1895,6 @@ static int udc_start(struct ci_hdrc *ci)
 	struct usb_otg_caps *otg_caps = &ci->platdata->ci_otg_caps;
 	int retval = 0;
 
-	spin_lock_init(&ci->lock);
-
 	ci->gadget.ops          = &usb_gadget_ops;
 	ci->gadget.speed        = USB_SPEED_UNKNOWN;
 	ci->gadget.max_speed    = USB_SPEED_HIGH;