blob: b9983f8e09f68d00eb7166bd279d34db522c8114 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
|
#!/bin/sh
# This validates that the kernel will fall back to using the user helper
# to load firmware it can't find on disk itself. We must request a firmware
# that the kernel won't find, and any installed helper (e.g. udev) also
# won't find so that we can do the load ourself manually.
set -e
modprobe test_firmware
DIR=/sys/devices/virtual/misc/test_firmware
# CONFIG_FW_LOADER_USER_HELPER has a sysfs class under /sys/class/firmware/
# These days no one enables CONFIG_FW_LOADER_USER_HELPER so check for that
# as an indicator for CONFIG_FW_LOADER_USER_HELPER.
HAS_FW_LOADER_USER_HELPER=$(if [ -d /sys/class/firmware/ ]; then echo yes; else echo no; fi)
if [ "$HAS_FW_LOADER_USER_HELPER" = "yes" ]; then
OLD_TIMEOUT=$(cat /sys/class/firmware/timeout)
else
echo "usermode helper disabled so ignoring test"
exit 0
fi
FWPATH=$(mktemp -d)
FW="$FWPATH/test-firmware.bin"
test_finish()
{
echo "$OLD_TIMEOUT" >/sys/class/firmware/timeout
rm -f "$FW"
rmdir "$FWPATH"
}
load_fw()
{
local name="$1"
local file="$2"
# This will block until our load (below) has finished.
echo -n "$name" >"$DIR"/trigger_request &
# Give kernel a chance to react.
local timeout=10
while [ ! -e "$DIR"/"$name"/loading ]; do
sleep 0.1
timeout=$(( $timeout - 1 ))
if [ "$timeout" -eq 0 ]; then
echo "$0: firmware interface never appeared" >&2
exit 1
fi
done
echo 1 >"$DIR"/"$name"/loading
cat "$file" >"$DIR"/"$name"/data
echo 0 >"$DIR"/"$name"/loading
# Wait for request to finish.
wait
}
trap "test_finish" EXIT
# This is an unlikely real-world firmware content. :)
echo "ABCD0123" >"$FW"
NAME=$(basename "$FW")
# Test failure when doing nothing (timeout works).
echo 1 >/sys/class/firmware/timeout
echo -n "$NAME" >"$DIR"/trigger_request
if diff -q "$FW" /dev/test_firmware >/dev/null ; then
echo "$0: firmware was not expected to match" >&2
exit 1
else
echo "$0: timeout works"
fi
# Put timeout high enough for us to do work but not so long that failures
# slow down this test too much.
echo 4 >/sys/class/firmware/timeout
# Load this script instead of the desired firmware.
load_fw "$NAME" "$0"
if diff -q "$FW" /dev/test_firmware >/dev/null ; then
echo "$0: firmware was not expected to match" >&2
exit 1
else
echo "$0: firmware comparison works"
fi
# Do a proper load, which should work correctly.
load_fw "$NAME" "$FW"
if ! diff -q "$FW" /dev/test_firmware >/dev/null ; then
echo "$0: firmware was not loaded" >&2
exit 1
else
echo "$0: user helper firmware loading works"
fi
exit 0
|
